summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/devicetree/bindings/dma
diff options
context:
space:
mode:
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/dma')
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt61
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt2
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt54
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/dma.txt28
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt54
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/mv-xor.txt12
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt3
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt46
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt5
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt63
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/ti-edma.txt115
-rw-r--r--kernel/Documentation/devicetree/bindings/dma/zxdma.txt38
12 files changed, 470 insertions, 11 deletions
diff --git a/kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
new file mode 100644
index 000000000..47cb1d14b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
@@ -0,0 +1,61 @@
+Analog Device AXI-DMAC DMA controller
+
+Required properties:
+ - compatible: Must be "adi,axi-dmac-1.00.a".
+ - reg: Specification for the controllers memory mapped register map.
+ - interrupts: Specification for the controllers interrupt.
+ - clocks: Phandle and specifier to the controllers AXI interface clock
+ - #dma-cells: Must be 1.
+
+Required sub-nodes:
+ - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
+ the channel sub-nodes the following bindings apply. They must match the
+ configuration options of the peripheral as it was instantiated.
+
+Required properties for adi,channels sub-node:
+ - #size-cells: Must be 0
+ - #address-cells: Must be 1
+
+Required channel sub-node properties:
+ - reg: Which channel this node refers to.
+ - adi,length-width: Width of the DMA transfer length register.
+ - adi,source-bus-width,
+ adi,destination-bus-width: Width of the source or destination bus in bits.
+ - adi,source-bus-type,
+ adi,destination-bus-type: Type of the source or destination bus. Must be one
+ of the following:
+ 0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
+ 1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
+ 2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
+
+Optional channel properties:
+ - adi,cyclic: Must be set if the channel supports hardware cyclic DMA
+ transfers.
+ - adi,2d: Must be set if the channel supports hardware 2D DMA transfers.
+
+DMA clients connected to the AXI-DMAC DMA controller must use the format
+described in the dma.txt file using a one-cell specifier. The value of the
+specifier refers to the DMA channel index.
+
+Example:
+
+dma: dma@7c420000 {
+ compatible = "adi,axi-dmac-1.00.a";
+ reg = <0x7c420000 0x10000>;
+ interrupts = <0 57 0>;
+ clocks = <&clkc 16>;
+ #dma-cells = <1>;
+
+ adi,channels {
+ #size-cells = <0>;
+ #address-cells = <1>;
+
+ dma-channel@0 {
+ reg = <0>;
+ adi,source-bus-width = <32>;
+ adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>;
+ adi,destination-bus-width = <64>;
+ adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>;
+ };
+ };
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt b/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt
index d3058768b..c53e0b080 100644
--- a/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt
@@ -35,7 +35,7 @@ Example:
device_type = "dma";
reg = <0x0 0x1f270000 0x0 0x10000>,
<0x0 0x1f200000 0x0 0x10000>,
- <0x0 0x1b008000 0x0 0x2000>,
+ <0x0 0x1b000000 0x0 0x400000>,
<0x0 0x1054a000 0x0 0x100>;
interrupts = <0x0 0x82 0x4>,
<0x0 0xb8 0x4>,
diff --git a/kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt b/kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt
new file mode 100644
index 000000000..8a0097a02
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/arm-pl08x.txt
@@ -0,0 +1,54 @@
+* ARM PrimeCells PL080 and PL081 and derivatives DMA controller
+
+Required properties:
+- compatible: "arm,pl080", "arm,primecell";
+ "arm,pl081", "arm,primecell";
+- reg: Address range of the PL08x registers
+- interrupt: The PL08x interrupt number
+- clocks: The clock running the IP core clock
+- clock-names: Must contain "apb_pclk"
+- lli-bus-interface-ahb1: if AHB master 1 is eligible for fetching LLIs
+- lli-bus-interface-ahb2: if AHB master 2 is eligible for fetching LLIs
+- mem-bus-interface-ahb1: if AHB master 1 is eligible for fetching memory contents
+- mem-bus-interface-ahb2: if AHB master 2 is eligible for fetching memory contents
+- #dma-cells: must be <2>. First cell should contain the DMA request,
+ second cell should contain either 1 or 2 depending on
+ which AHB master that is used.
+
+Optional properties:
+- dma-channels: contains the total number of DMA channels supported by the DMAC
+- dma-requests: contains the total number of DMA requests supported by the DMAC
+- memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32
+ 64, 128 or 256 bytes are legal values
+- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal
+ values
+
+Clients
+Required properties:
+- dmas: List of DMA controller phandle, request channel and AHB master id
+- dma-names: Names of the aforementioned requested channels
+
+Example:
+
+dmac0: dma-controller@10130000 {
+ compatible = "arm,pl080", "arm,primecell";
+ reg = <0x10130000 0x1000>;
+ interrupt-parent = <&vica>;
+ interrupts = <15>;
+ clocks = <&hclkdma0>;
+ clock-names = "apb_pclk";
+ lli-bus-interface-ahb1;
+ lli-bus-interface-ahb2;
+ mem-bus-interface-ahb2;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+ #dma-cells = <2>;
+};
+
+device@40008000 {
+ ...
+ dmas = <&dmac0 0 2
+ &dmac0 1 2>;
+ dma-names = "tx", "rx";
+ ...
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/dma.txt b/kernel/Documentation/devicetree/bindings/dma/dma.txt
index 82104271e..6312fb00c 100644
--- a/kernel/Documentation/devicetree/bindings/dma/dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/dma.txt
@@ -31,6 +31,34 @@ Example:
dma-requests = <127>;
};
+* DMA router
+
+DMA routers are transparent IP blocks used to route DMA request lines from
+devices to the DMA controller. Some SoCs (like TI DRA7x) have more peripherals
+integrated with DMA requests than what the DMA controller can handle directly.
+
+Required property:
+- dma-masters: phandle of the DMA controller or list of phandles for
+ the DMA controllers the router can direct the signal to.
+- #dma-cells: Must be at least 1. Used to provide DMA router specific
+ information. See DMA client binding below for more
+ details.
+
+Optional properties:
+- dma-requests: Number of incoming request lines the router can handle.
+- In the node pointed by the dma-masters:
+ - dma-requests: The router driver might need to look for this in order
+ to configure the routing.
+
+Example:
+ sdma_xbar: dma-router@4a002b78 {
+ compatible = "ti,dra7-dma-crossbar";
+ reg = <0x4a002b78 0xfc>;
+ #dma-cells = <1>;
+ dma-requests = <205>;
+ ti,dma-safe-map = <0>;
+ dma-masters = <&sdma>;
+ };
* DMA client
diff --git a/kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt b/kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
new file mode 100644
index 000000000..87740adb2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
@@ -0,0 +1,54 @@
+NXP LPC18xx/43xx DMA MUX (DMA request router)
+
+Required properties:
+- compatible: "nxp,lpc1850-dmamux"
+- reg: Memory map for accessing module
+- #dma-cells: Should be set to <3>.
+ * 1st cell contain the master dma request signal
+ * 2nd cell contain the mux value (0-3) for the peripheral
+ * 3rd cell contain either 1 or 2 depending on the AHB
+ master used.
+- dma-requests: Number of DMA requests for the mux
+- dma-masters: phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests: Number of DMA requests the controller can handle
+
+Example:
+
+dmac: dma@40002000 {
+ compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell";
+ arm,primecell-periphid = <0x00041080>;
+ reg = <0x40002000 0x1000>;
+ interrupts = <2>;
+ clocks = <&ccu1 CLK_CPU_DMA>;
+ clock-names = "apb_pclk";
+ #dma-cells = <2>;
+ dma-channels = <8>;
+ dma-requests = <16>;
+ lli-bus-interface-ahb1;
+ lli-bus-interface-ahb2;
+ mem-bus-interface-ahb1;
+ mem-bus-interface-ahb2;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+};
+
+dmamux: dma-mux {
+ compatible = "nxp,lpc1850-dmamux";
+ #dma-cells = <3>;
+ dma-requests = <64>;
+ dma-masters = <&dmac>;
+};
+
+uart0: serial@40081000 {
+ compatible = "nxp,lpc1850-uart", "ns16550a";
+ reg = <0x40081000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <24>;
+ clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+ clock-names = "uartclk", "reg";
+ dmas = <&dmamux 1 1 2
+ &dmamux 2 1 2>;
+ dma-names = "tx", "rx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt b/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt
index 7c6cb7fce..276ef815e 100644
--- a/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/mv-xor.txt
@@ -1,7 +1,7 @@
* Marvell XOR engines
Required properties:
-- compatible: Should be "marvell,orion-xor"
+- compatible: Should be "marvell,orion-xor" or "marvell,armada-380-xor"
- reg: Should contain registers location and length (two sets)
the first set is the low registers, the second set the high
registers for the XOR engine.
@@ -12,10 +12,13 @@ XOR engine has. Those sub-nodes have the following required
properties:
- interrupts: interrupt of the XOR channel
-And the following optional properties:
+The sub-nodes used to contain one or several of the following
+properties, but they are now deprecated:
- dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations
- dmacap,memset to indicate that the XOR channel is capable of memset operations
- dmacap,xor to indicate that the XOR channel is capable of xor operations
+- dmacap,interrupt to indicate that the XOR channel is capable of
+ generating interrupts
Example:
@@ -28,13 +31,8 @@ xor@d0060900 {
xor00 {
interrupts = <51>;
- dmacap,memcpy;
- dmacap,xor;
};
xor01 {
interrupts = <52>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
};
};
diff --git a/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt b/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt
index ecbc96ad3..ccd52d6a2 100644
--- a/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/sirfsoc-dma.txt
@@ -3,7 +3,8 @@
See dma.txt first
Required properties:
-- compatible: Should be "sirf,prima2-dmac" or "sirf,marco-dmac"
+- compatible: Should be "sirf,prima2-dmac", "sirf,atlas7-dmac" or
+ "sirf,atlas7-dmac-v2"
- reg: Should contain DMA registers location and length.
- interrupts: Should contain one interrupt shared by all channel
- #dma-cells: must be <1>. used to represent the number of integer
diff --git a/kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt
new file mode 100644
index 000000000..f1634a27a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/sun4i-dma.txt
@@ -0,0 +1,46 @@
+Allwinner A10 DMA Controller
+
+This driver follows the generic DMA bindings defined in dma.txt.
+
+Required properties:
+
+- compatible: Must be "allwinner,sun4i-a10-dma"
+- reg: Should contain the registers base address and length
+- interrupts: Should contain a reference to the interrupt used by this device
+- clocks: Should contain a reference to the parent AHB clock
+- #dma-cells : Should be 2, first cell denoting normal or dedicated dma,
+ second cell holding the request line number.
+
+Example:
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun4i-a10-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <27>;
+ clocks = <&ahb_gates 6>;
+ #dma-cells = <2>;
+ };
+
+Clients:
+
+DMA clients connected to the Allwinner A10 DMA controller must use the
+format described in the dma.txt file, using a three-cell specifier for
+each channel: a phandle plus two integer cells.
+The three cells in order are:
+
+1. A phandle pointing to the DMA controller.
+2. Whether it is using normal (0) or dedicated (1) channels
+3. The port ID as specified in the datasheet
+
+Example:
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <0 12 4>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 1 29>, <&dma 1 28>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
diff --git a/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt
index 9cdcba24d..d13c136ce 100644
--- a/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -4,7 +4,10 @@ This driver follows the generic DMA bindings defined in dma.txt.
Required properties:
-- compatible: Must be "allwinner,sun6i-a31-dma" or "allwinner,sun8i-a23-dma"
+- compatible: Must be one of
+ "allwinner,sun6i-a31-dma"
+ "allwinner,sun8i-a23-dma"
+ "allwinner,sun8i-h3-dma"
- reg: Should contain the registers base address and length
- interrupts: Should contain a reference to the interrupt used by this device
- clocks: Should contain a reference to the parent AHB clock
diff --git a/kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt b/kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt
new file mode 100644
index 000000000..b152a75dc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt
@@ -0,0 +1,63 @@
+Texas Instruments DMA Crossbar (DMA request router)
+
+Required properties:
+- compatible: "ti,dra7-dma-crossbar" for DRA7xx DMA crossbar
+ "ti,am335x-edma-crossbar" for AM335x and AM437x
+- reg: Memory map for accessing module
+- #dma-cells: Should be set to to match with the DMA controller's dma-cells
+ for ti,dra7-dma-crossbar and <3> for ti,am335x-edma-crossbar.
+- dma-requests: Number of DMA requests the crossbar can receive
+- dma-masters: phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests: Number of DMA requests the controller can handle
+
+Optional properties:
+- ti,dma-safe-map: Safe routing value for unused request lines
+
+Notes:
+When requesting channel via ti,dra7-dma-crossbar, the DMA clinet must request
+the DMA event number as crossbar ID (input to the DMA crossbar).
+
+For ti,am335x-edma-crossbar: the meaning of parameters of dmas for clients:
+dmas = <&edma_xbar 12 0 1>; where <12> is the DMA request number, <0> is the TC
+the event should be assigned and <1> is the mux selection for in the crossbar.
+When mux 0 is used the DMA channel can be requested directly from edma node.
+
+Example:
+
+/* DMA controller */
+sdma: dma-controller@4a056000 {
+ compatible = "ti,omap4430-sdma";
+ reg = <0x4a056000 0x1000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ dma-channels = <32>;
+ dma-requests = <127>;
+};
+
+/* DMA crossbar */
+sdma_xbar: dma-router@4a002b78 {
+ compatible = "ti,dra7-dma-crossbar";
+ reg = <0x4a002b78 0xfc>;
+ #dma-cells = <1>;
+ dma-requests = <205>;
+ ti,dma-safe-map = <0>;
+ dma-masters = <&sdma>;
+};
+
+/* DMA client */
+uart1: serial@4806a000 {
+ compatible = "ti,omap4-uart";
+ reg = <0x4806a000 0x100>;
+ interrupts-extended = <&gic GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "uart1";
+ clock-frequency = <48000000>;
+ status = "disabled";
+ /* Requesting crossbar input 49 and 50 */
+ dmas = <&sdma_xbar 49>, <&sdma_xbar 50>;
+ dma-names = "tx", "rx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt b/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt
index 5ba525a10..079b42a81 100644
--- a/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/kernel/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -1,4 +1,117 @@
-TI EDMA
+Texas Instruments eDMA
+
+The eDMA3 consists of two components: Channel controller (CC) and Transfer
+Controller(s) (TC). The CC is the main entry for DMA users since it is
+responsible for the DMA channel handling, while the TCs are responsible to
+execute the actual DMA tansfer.
+
+------------------------------------------------------------------------------
+eDMA3 Channel Controller
+
+Required properties:
+- compatible: "ti,edma3-tpcc" for the channel controller(s)
+- #dma-cells: Should be set to <2>. The first number is the DMA request
+ number and the second is the TC the channel is serviced on.
+- reg: Memory map of eDMA CC
+- reg-names: "edma3_cc"
+- interrupts: Interrupt lines for CCINT, MPERR and CCERRINT.
+- interrupt-names: "edma3_ccint", "emda3_mperr" and "edma3_ccerrint"
+- ti,tptcs: List of TPTCs associated with the eDMA in the following form:
+ <&tptc_phandle TC_priority_number>. The highest priority is 0.
+
+Optional properties:
+- ti,hwmods: Name of the hwmods associated to the eDMA CC
+- ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow
+ these channels will be SW triggered channels. See example.
+- ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by
+ the driver, they are allocated to be used by for example the
+ DSP. See example.
+
+------------------------------------------------------------------------------
+eDMA3 Transfer Controller
+
+Required properties:
+- compatible: "ti,edma3-tptc" for the transfer controller(s)
+- reg: Memory map of eDMA TC
+- interrupts: Interrupt number for TCerrint.
+
+Optional properties:
+- ti,hwmods: Name of the hwmods associated to the given eDMA TC
+- interrupt-names: "edma3_tcerrint"
+
+------------------------------------------------------------------------------
+Example:
+
+edma: edma@49000000 {
+ compatible = "ti,edma3-tpcc";
+ ti,hwmods = "tpcc";
+ reg = <0x49000000 0x10000>;
+ reg-names = "edma3_cc";
+ interrupts = <12 13 14>;
+ interrupt-names = "edma3_ccint", "emda3_mperr", "edma3_ccerrint";
+ dma-requests = <64>;
+ #dma-cells = <2>;
+
+ ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 7>, <&edma_tptc2 0>;
+
+ /* Channel 20 and 21 is allocated for memcpy */
+ ti,edma-memcpy-channels = <20 21>;
+ /* The following PaRAM slots are reserved: 35-44 and 100-109 */
+ ti,edma-reserved-slot-ranges = <35 10>, <100 10>;
+};
+
+edma_tptc0: tptc@49800000 {
+ compatible = "ti,edma3-tptc";
+ ti,hwmods = "tptc0";
+ reg = <0x49800000 0x100000>;
+ interrupts = <112>;
+ interrupt-names = "edm3_tcerrint";
+};
+
+edma_tptc1: tptc@49900000 {
+ compatible = "ti,edma3-tptc";
+ ti,hwmods = "tptc1";
+ reg = <0x49900000 0x100000>;
+ interrupts = <113>;
+ interrupt-names = "edm3_tcerrint";
+};
+
+edma_tptc2: tptc@49a00000 {
+ compatible = "ti,edma3-tptc";
+ ti,hwmods = "tptc2";
+ reg = <0x49a00000 0x100000>;
+ interrupts = <114>;
+ interrupt-names = "edm3_tcerrint";
+};
+
+sham: sham@53100000 {
+ compatible = "ti,omap4-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x200>;
+ interrupts = <109>;
+ /* DMA channel 36 executed on eDMA TC0 - low priority queue */
+ dmas = <&edma 36 0>;
+ dma-names = "rx";
+};
+
+mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupt-names = "tx", "rx";
+ status = "disabled";
+ /* DMA channels 8 and 9 executed on eDMA TC2 - high priority queue */
+ dmas = <&edma 8 2>,
+ <&edma 9 2>;
+ dma-names = "tx", "rx";
+};
+
+------------------------------------------------------------------------------
+DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc
+binding.
Required properties:
- compatible : "ti,edma3"
diff --git a/kernel/Documentation/devicetree/bindings/dma/zxdma.txt b/kernel/Documentation/devicetree/bindings/dma/zxdma.txt
new file mode 100644
index 000000000..3207ceb04
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/zxdma.txt
@@ -0,0 +1,38 @@
+* ZTE ZX296702 DMA controller
+
+Required properties:
+- compatible: Should be "zte,zx296702-dma"
+- reg: Should contain DMA registers location and length.
+- interrupts: Should contain one interrupt shared by all channel
+- #dma-cells: see dma.txt, should be 1, para number
+- dma-channels: physical channels supported
+- dma-requests: virtual channels supported, each virtual channel
+ have specific request line
+- clocks: clock required
+
+Example:
+
+Controller:
+ dma: dma-controller@0x09c00000{
+ compatible = "zte,zx296702-dma";
+ reg = <0x09c00000 0x1000>;
+ clocks = <&topclk ZX296702_DMA_ACLK>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ dma-channels = <24>;
+ dma-requests = <24>;
+ };
+
+Client:
+Use specific request line passing from dmax
+For example, spdif0 tx channel request line is 4
+ spdif0: spdif0@0b004000 {
+ #sound-dai-cells = <0>;
+ compatible = "zte,zx296702-spdif";
+ reg = <0x0b004000 0x1000>;
+ clocks = <&lsp0clk ZX296702_SPDIF0_DIV>;
+ clock-names = "tx";
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma 4>;
+ dma-names = "tx";
+ }