diff options
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/clock/ti')
12 files changed, 771 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/apll.txt b/kernel/Documentation/devicetree/bindings/clock/ti/apll.txt new file mode 100644 index 000000000..ade4dd4c3 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/apll.txt @@ -0,0 +1,45 @@ +Binding for Texas Instruments APLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped APLL with usually two selectable input clocks +(reference clock and bypass clock), with analog phase locked +loop logic for multiplying the input clock to a desired output +clock. This clock also typically supports different operation +modes (locked, low power stop etc.) APLL mostly behaves like +a subtype of a DPLL [2], although a simplified one at that. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/dpll.txt + +Required properties: +- compatible : shall be "ti,dra7-apll-clock" or "ti,omap2-apll-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks (clk-ref and clk-bypass) +- reg : address and length of the register set for controlling the APLL. + It contains the information of registers in the following order: + "control" - contains the control register offset + "idlest" - contains the idlest register offset + "autoidle" - contains the autoidle register offset (OMAP2 only) +- ti,clock-frequency : static clock frequency for the clock (OMAP2 only) +- ti,idlest-shift : bit-shift for the idlest field (OMAP2 only) +- ti,bit-shift : bit-shift for enable and autoidle fields (OMAP2 only) + +Examples: + apll_pcie_ck: apll_pcie_ck { + #clock-cells = <0>; + clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>; + reg = <0x021c>, <0x0220>; + compatible = "ti,dra7-apll-clock"; + }; + + apll96_ck: apll96_ck { + #clock-cells = <0>; + compatible = "ti,omap2-apll-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <2>; + ti,idlest-shift = <8>; + ti,clock-frequency = <96000000>; + reg = <0x0500>, <0x0530>, <0x0520>; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/autoidle.txt b/kernel/Documentation/devicetree/bindings/clock/ti/autoidle.txt new file mode 100644 index 000000000..7c735dde9 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/autoidle.txt @@ -0,0 +1,39 @@ +Binding for Texas Instruments autoidle clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a register mapped +clock which can be put to idle automatically by hardware based on the usage +and a configuration bit setting. Autoidle clock is never an individual +clock, it is always a derivative of some basic clock like a gate, divider, +or fixed-factor. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- reg : offset for the register controlling the autoidle +- ti,autoidle-shift : bit shift of the autoidle enable bit +- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0 + +Examples: + dpll_core_m4_ck: dpll_core_m4_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + ti,autoidle-shift = <8>; + reg = <0x2d38>; + ti,index-starts-at-one; + ti,invert-autoidle-bit; + }; + + dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck { + #clock-cells = <0>; + compatible = "ti,fixed-factor-clock"; + clocks = <&dpll_usb_ck>; + ti,clock-div = <1>; + ti,autoidle-shift = <8>; + reg = <0x01b4>; + ti,clock-mult = <1>; + ti,invert-autoidle-bit; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/clockdomain.txt b/kernel/Documentation/devicetree/bindings/clock/ti/clockdomain.txt new file mode 100644 index 000000000..cb76b3f2b --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/clockdomain.txt @@ -0,0 +1,24 @@ +Binding for Texas Instruments clockdomain. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1] in consumer role. +Every clock on TI SoC belongs to one clockdomain, but software +only needs this information for specific clocks which require +their parent clockdomain to be controlled when the clock is +enabled/disabled. This binding doesn't define a new clock +binding type, it is used to group existing clock nodes under +hardware hierarchy. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,clockdomain" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of clocks within this domain + +Examples: + dss_clkdm: dss_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dss1_alwon_fck_3430es2>, <&dss_ick_3430es2>; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/composite.txt b/kernel/Documentation/devicetree/bindings/clock/ti/composite.txt new file mode 100644 index 000000000..5f43c4706 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/composite.txt @@ -0,0 +1,54 @@ +Binding for TI composite clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped composite clock with multiple different sub-types; + +a multiplexer clock with multiple input clock signals or parents, one +of which can be selected as output, this behaves exactly as [2] + +an adjustable clock rate divider, this behaves exactly as [3] + +a gating function which can be used to enable and disable the output +clock, this behaves exactly as [4] + +The binding must provide a list of the component clocks that shall be +merged to this clock. The component clocks shall be of one of the +"ti,*composite*-clock" types. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/mux.txt +[3] Documentation/devicetree/bindings/clock/ti/divider.txt +[4] Documentation/devicetree/bindings/clock/ti/gate.txt + +Required properties: +- compatible : shall be: "ti,composite-clock" +- clocks : link phandles of component clocks +- #clock-cells : from common clock binding; shall be set to 0. + +Examples: + +usb_l4_gate_ick: usb_l4_gate_ick { + #clock-cells = <0>; + compatible = "ti,composite-interface-clock"; + clocks = <&l4_ick>; + ti,bit-shift = <5>; + reg = <0x0a10>; +}; + +usb_l4_div_ick: usb_l4_div_ick { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&l4_ick>; + ti,bit-shift = <4>; + ti,max-div = <1>; + reg = <0x0a40>; + ti,index-starts-at-one; +}; + +usb_l4_ick: usb_l4_ick { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&usb_l4_gate_ick>, <&usb_l4_div_ick>; +}; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/divider.txt b/kernel/Documentation/devicetree/bindings/clock/ti/divider.txt new file mode 100644 index 000000000..35a6f5c7e --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/divider.txt @@ -0,0 +1,114 @@ +Binding for TI divider clock + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped adjustable clock rate divider that does not gate and has +only one input clock or parent. By default the value programmed into +the register is one less than the actual divisor value. E.g: + +register value actual divisor value +0 1 +1 2 +2 3 + +This assumption may be modified by the following optional properties: + +ti,index-starts-at-one - valid divisor values start at 1, not the default +of 0. E.g: +register value actual divisor value +1 1 +2 2 +3 3 + +ti,index-power-of-two - valid divisor values are powers of two. E.g: +register value actual divisor value +0 1 +1 2 +2 4 + +Additionally an array of valid dividers may be supplied like so: + + ti,dividers = <4>, <8>, <0>, <16>; + +Which will map the resulting values to a divisor table by their index: +register value actual divisor value +0 4 +1 8 +2 <invalid divisor, skipped> +3 16 + +Any zero value in this array means the corresponding bit-value is invalid +and must not be used. + +The binding must also provide the register to control the divider and +unless the divider array is provided, min and max dividers. Optionally +the number of bits to shift that mask, if necessary. If the shift value +is missing it is the same as supplying a zero shift. + +This binding can also optionally provide support to the hardware autoidle +feature, see [2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt + +Required properties: +- compatible : shall be "ti,divider-clock" or "ti,composite-divider-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link to phandle of parent clock +- reg : offset for register controlling adjustable divider + +Optional properties: +- clock-output-names : from common clock binding. +- ti,dividers : array of integers defining divisors +- ti,bit-shift : number of bits to shift the divider value, defaults to 0 +- ti,min-div : min divisor for dividing the input clock rate, only + needed if the first divisor is offset from the default value (1) +- ti,max-div : max divisor for dividing the input clock rate, only needed + if ti,dividers is not defined. +- ti,index-starts-at-one : valid divisor programming starts at 1, not zero, + only valid if ti,dividers is not defined. +- ti,index-power-of-two : valid divisor programming must be a power of two, + only valid if ti,dividers is not defined. +- ti,autoidle-shift : bit shift of the autoidle enable bit for the clock, + see [2] +- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0, + see [2] +- ti,set-rate-parent : clk_set_rate is propagated to parent + +Examples: +dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_usb_ck>; + ti,max-div = <127>; + reg = <0x190>; + ti,index-starts-at-one; +}; + +aess_fclk: aess_fclk@4a004528 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&abe_clk>; + ti,bit-shift = <24>; + reg = <0x528>; + ti,max-div = <2>; +}; + +dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + reg = <0x0134>; + ti,index-starts-at-one; +}; + +ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2 { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&corex2_fck>; + ti,bit-shift = <8>; + reg = <0x0a40>; + ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; +}; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/dpll.txt b/kernel/Documentation/devicetree/bindings/clock/ti/dpll.txt new file mode 100644 index 000000000..df57009ff --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/dpll.txt @@ -0,0 +1,85 @@ +Binding for Texas Instruments DPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped DPLL with usually two selectable input clocks +(reference clock and bypass clock), with digital phase locked +loop logic for multiplying the input clock to a desired output +clock. This clock also typically supports different operation +modes (locked, low power stop etc.) This binding has several +sub-types, which effectively result in slightly different setup +for the actual DPLL clock. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of: + "ti,omap3-dpll-clock", + "ti,omap3-dpll-core-clock", + "ti,omap3-dpll-per-clock", + "ti,omap3-dpll-per-j-type-clock", + "ti,omap4-dpll-clock", + "ti,omap4-dpll-x2-clock", + "ti,omap4-dpll-core-clock", + "ti,omap4-dpll-m4xen-clock", + "ti,omap4-dpll-j-type-clock", + "ti,omap5-mpu-dpll-clock", + "ti,am3-dpll-no-gate-clock", + "ti,am3-dpll-j-type-clock", + "ti,am3-dpll-no-gate-j-type-clock", + "ti,am3-dpll-clock", + "ti,am3-dpll-core-clock", + "ti,am3-dpll-x2-clock", + "ti,omap2-dpll-core-clock", + +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks, first entry lists reference clock + and second entry bypass clock +- reg : offsets for the register set for controlling the DPLL. + Registers are listed in following order: + "control" - contains the control register base address + "idlest" - contains the idle status register base address + "mult-div1" - contains the multiplier / divider register base address + "autoidle" - contains the autoidle register base address (optional) + ti,am3-* dpll types do not have autoidle register + ti,omap2-* dpll type does not support idlest / autoidle registers + +Optional properties: +- DPLL mode setting - defining any one or more of the following overrides + default setting. + - ti,low-power-stop : DPLL supports low power stop mode, gating output + - ti,low-power-bypass : DPLL output matches rate of parent bypass clock + - ti,lock : DPLL locks in programmed rate + +Examples: + dpll_core_ck: dpll_core_ck@44e00490 { + #clock-cells = <0>; + compatible = "ti,omap4-dpll-core-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x490>, <0x45c>, <0x488>, <0x468>; + }; + + dpll2_ck: dpll2_ck@48004004 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-clock"; + clocks = <&sys_ck>, <&dpll2_fck>; + ti,low-power-stop; + ti,low-power-bypass; + ti,lock; + reg = <0x4>, <0x24>, <0x34>, <0x40>; + }; + + dpll_core_ck: dpll_core_ck@44e00490 { + #clock-cells = <0>; + compatible = "ti,am3-dpll-core-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x90>, <0x5c>, <0x68>; + }; + + dpll_ck: dpll_ck { + #clock-cells = <0>; + compatible = "ti,omap2-dpll-core-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0500>, <0x0540>; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt b/kernel/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt new file mode 100644 index 000000000..585e8c191 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt @@ -0,0 +1,96 @@ +Device Tree Clock bindings for ATL (Audio Tracking Logic) of DRA7 SoC. + +The ATL IP is used to generate clock to be used to synchronize baseband and +audio codec. A single ATL IP provides four ATL clock instances sharing the same +functional clock but can be configured to provide different clocks. +ATL can maintain a clock averages to some desired frequency based on the bws/aws +signals - can compensate the drift between the two ws signal. + +In order to provide the support for ATL and it's output clocks (which can be used +internally within the SoC or external components) two sets of bindings is needed: + +Clock tree binding: +This binding uses the common clock binding[1]. +To be able to integrate the ATL clocks with DT clock tree. +Provides ccf level representation of the ATL clocks to be used by drivers. +Since the clock instances are part of a single IP this binding is used as a node +for the DT clock tree, the IP driver is needed to handle the actual configuration +of the IP. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dra7-atl-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles to functional clock of ATL + +Binding for the IP driver: +This binding is used to configure the IP driver which is going to handle the +configuration of the IP for the ATL clock instances. + +Required properties: +- compatible : shall be "ti,dra7-atl" +- reg : base address for the ATL IP +- ti,provided-clocks : List of phandles to the clocks associated with the ATL +- clocks : link phandles to functional clock of ATL +- clock-names : Shall be set to "fck" +- ti,hwmods : Shall be set to "atl" + +Optional properties: +Configuration of ATL instances: +- atl{0/1/2/3} { + - bws : Baseband word select signal selection + - aws : Audio word select signal selection +}; + +For valid word select signals, see the dt-bindings/clk/ti-dra7-atl.h include +file. + +Examples: +/* clock bindings for atl provided clocks */ +atl_clkin0_ck: atl_clkin0_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin1_ck: atl_clkin1_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin2_ck: atl_clkin2_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin3_ck: atl_clkin3_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +/* binding for the IP */ +atl: atl@4843c000 { + compatible = "ti,dra7-atl"; + reg = <0x4843c000 0x3ff>; + ti,hwmods = "atl"; + ti,provided-clocks = <&atl_clkin0_ck>, <&atl_clkin1_ck>, + <&atl_clkin2_ck>, <&atl_clkin3_ck>; + clocks = <&atl_gfclk_mux>; + clock-names = "fck"; + status = "disabled"; +}; + +#include <dt-bindings/clk/ti-dra7-atl.h> + +&atl { + status = "okay"; + + atl2 { + bws = <DRA7_ATL_WS_MCASP2_FSX>; + aws = <DRA7_ATL_WS_MCASP3_FSX>; + }; +}; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/fapll.txt b/kernel/Documentation/devicetree/bindings/clock/ti/fapll.txt new file mode 100644 index 000000000..c19b3f253 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/fapll.txt @@ -0,0 +1,33 @@ +Binding for Texas Instruments FAPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped FAPLL with usually two selectable input clocks +(reference clock and bypass clock), and one or more child +syntesizers. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dm816-fapll-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks (clk-ref and clk-bypass) +- reg : address and length of the register set for controlling the FAPLL. + +Examples: + main_fapll: main_fapll { + #clock-cells = <1>; + compatible = "ti,dm816-fapll-clock"; + reg = <0x400 0x40>; + clocks = <&sys_clkin_ck &sys_clkin_ck>; + clock-indices = <1>, <2>, <3>, <4>, <5>, + <6>, <7>; + clock-output-names = "main_pll_clk1", + "main_pll_clk2", + "main_pll_clk3", + "main_pll_clk4", + "main_pll_clk5", + "main_pll_clk6", + "main_pll_clk7"; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt b/kernel/Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt new file mode 100644 index 000000000..662b36d53 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt @@ -0,0 +1,43 @@ +Binding for TI fixed factor rate clock sources. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1], and also uses the autoidle +support from TI autoidle clock [2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt + +Required properties: +- compatible : shall be "ti,fixed-factor-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- ti,clock-div: fixed divider. +- ti,clock-mult: fixed multiplier. +- clocks: parent clock. + +Optional properties: +- ti,autoidle-shift: bit shift of the autoidle enable bit for the clock, + see [2] +- reg: offset for the autoidle register of this clock, see [2] +- ti,invert-autoidle-bit: autoidle is enabled by setting the bit to 0, see [2] +- ti,set-rate-parent: clk_set_rate is propagated to parent + +Example: + clock { + compatible = "ti,fixed-factor-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + ti,clock-div = <2>; + ti,clock-mult = <1>; + }; + + dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck { + #clock-cells = <0>; + compatible = "ti,fixed-factor-clock"; + clocks = <&dpll_usb_ck>; + ti,clock-div = <1>; + ti,autoidle-shift = <8>; + reg = <0x01b4>; + ti,clock-mult = <1>; + ti,invert-autoidle-bit; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/gate.txt b/kernel/Documentation/devicetree/bindings/clock/ti/gate.txt new file mode 100644 index 000000000..03f8fdee6 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/gate.txt @@ -0,0 +1,106 @@ +Binding for Texas Instruments gate clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. This clock is +quite much similar to the basic gate-clock [2], however, +it supports a number of additional features. If no register +is provided for this clock, the code assumes that a clockdomain +will be controlled instead and the corresponding hw-ops for +that is used. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/gate-clock.txt +[3] Documentation/devicetree/bindings/clock/ti/clockdomain.txt + +Required properties: +- compatible : shall be one of: + "ti,gate-clock" - basic gate clock + "ti,wait-gate-clock" - gate clock which waits until clock is active before + returning from clk_enable() + "ti,dss-gate-clock" - gate clock with DSS specific hardware handling + "ti,am35xx-gate-clock" - gate clock with AM35xx specific hardware handling + "ti,clkdm-gate-clock" - clockdomain gate clock, which derives its functional + clock directly from a clockdomain, see [3] how + to map clockdomains properly + "ti,hsdiv-gate-clock" - gate clock with OMAP36xx specific hardware handling, + required for a hardware errata + "ti,composite-gate-clock" - composite gate clock, to be part of composite + clock + "ti,composite-no-wait-gate-clock" - composite gate clock that does not wait + for clock to be active before returning + from clk_enable() +- #clock-cells : from common clock binding; shall be set to 0 +- clocks : link to phandle of parent clock +- reg : offset for register controlling adjustable gate, not needed for + ti,clkdm-gate-clock type + +Optional properties: +- ti,bit-shift : bit shift for programming the clock gate, invalid for + ti,clkdm-gate-clock type +- ti,set-bit-to-disable : inverts default gate programming. Setting the bit + gates the clock and clearing the bit ungates the clock. + +Examples: + mmchs2_fck: mmchs2_fck@48004a00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <25>; + }; + + uart4_fck_am35xx: uart4_fck_am35xx { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <23>; + }; + + dss1_alwon_fck_3430es2: dss1_alwon_fck_3430es2@48004e00 { + #clock-cells = <0>; + compatible = "ti,dss-gate-clock"; + clocks = <&dpll4_m4x2_ck>; + reg = <0x0e00>; + ti,bit-shift = <0>; + }; + + emac_ick: emac_ick@4800259c { + #clock-cells = <0>; + compatible = "ti,am35xx-gate-clock"; + clocks = <&ipss_ick>; + reg = <0x059c>; + ti,bit-shift = <1>; + }; + + emu_src_ck: emu_src_ck { + #clock-cells = <0>; + compatible = "ti,clkdm-gate-clock"; + clocks = <&emu_src_mux_ck>; + }; + + dpll4_m2x2_ck: dpll4_m2x2_ck@48004d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll4_m2x2_mul_ck>; + ti,bit-shift = <0x1b>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + vlynq_gate_fck: vlynq_gate_fck { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <3>; + reg = <0x0200>; + }; + + sys_clkout2_src_gate: sys_clkout2_src_gate { + #clock-cells = <0>; + compatible = "ti,composite-no-wait-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <15>; + reg = <0x0070>; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/interface.txt b/kernel/Documentation/devicetree/bindings/clock/ti/interface.txt new file mode 100644 index 000000000..3111a409f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/interface.txt @@ -0,0 +1,56 @@ +Binding for Texas Instruments interface clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. This clock is +quite much similar to the basic gate-clock [2], however, +it supports a number of additional features, including +companion clock finding (match corresponding functional gate +clock) and hardware autoidle enable / disable. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/gate-clock.txt + +Required properties: +- compatible : shall be one of: + "ti,omap3-interface-clock" - basic OMAP3 interface clock + "ti,omap3-no-wait-interface-clock" - interface clock which has no hardware + capability for waiting clock to be ready + "ti,omap3-hsotgusb-interface-clock" - interface clock with USB specific HW + handling + "ti,omap3-dss-interface-clock" - interface clock with DSS specific HW handling + "ti,omap3-ssi-interface-clock" - interface clock with SSI specific HW handling + "ti,am35xx-interface-clock" - interface clock with AM35xx specific HW handling + "ti,omap2430-interface-clock" - interface clock with OMAP2430 specific HW + handling +- #clock-cells : from common clock binding; shall be set to 0 +- clocks : link to phandle of parent clock +- reg : base address for the control register + +Optional properties: +- ti,bit-shift : bit shift for the bit enabling/disabling the clock (default 0) + +Examples: + aes1_ick: aes1_ick@48004a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x48004a14 0x4>; + ti,bit-shift = <3>; + }; + + cam_ick: cam_ick@48004f10 { + #clock-cells = <0>; + compatible = "ti,omap3-no-wait-interface-clock"; + clocks = <&l4_ick>; + reg = <0x48004f10 0x4>; + ti,bit-shift = <0>; + }; + + ssi_ick_3430es2: ssi_ick_3430es2@48004a10 { + #clock-cells = <0>; + compatible = "ti,omap3-ssi-interface-clock"; + clocks = <&ssi_l4_ick>; + reg = <0x48004a10 0x4>; + ti,bit-shift = <0>; + }; diff --git a/kernel/Documentation/devicetree/bindings/clock/ti/mux.txt b/kernel/Documentation/devicetree/bindings/clock/ti/mux.txt new file mode 100644 index 000000000..2d0d170f8 --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/clock/ti/mux.txt @@ -0,0 +1,76 @@ +Binding for TI mux clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped multiplexer with multiple input clock signals or +parents, one of which can be selected as output. This clock does not +gate or adjust the parent rate via a divider or multiplier. + +By default the "clocks" property lists the parents in the same order +as they are programmed into the regster. E.g: + + clocks = <&foo_clock>, <&bar_clock>, <&baz_clock>; + +results in programming the register as follows: + +register value selected parent clock +0 foo_clock +1 bar_clock +2 baz_clock + +Some clock controller IPs do not allow a value of zero to be programmed +into the register, instead indexing begins at 1. The optional property +"index-starts-at-one" modified the scheme as follows: + +register value selected clock parent +1 foo_clock +2 bar_clock +3 baz_clock + +The binding must provide the register to control the mux. Optionally +the number of bits to shift the control field in the register can be +supplied. If the shift value is missing it is the same as supplying +a zero shift. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,mux-clock" or "ti,composite-mux-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks +- reg : register offset for register controlling adjustable mux + +Optional properties: +- ti,bit-shift : number of bits to shift the bit-mask, defaults to + 0 if not present +- ti,index-starts-at-one : valid input select programming starts at 1, not + zero +- ti,set-rate-parent : clk_set_rate is propagated to parent clock, + not supported by the composite-mux-clock subtype + +Examples: + +sys_clkin_ck: sys_clkin_ck@4a306110 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>; + reg = <0x0110>; + ti,index-starts-at-one; +}; + +abe_dpll_bypass_clk_mux_ck: abe_dpll_bypass_clk_mux_ck@4a306108 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sys_clkin_ck>, <&sys_32k_ck>; + ti,bit-shift = <24>; + reg = <0x0108>; +}; + +mcbsp5_mux_fck: mcbsp5_mux_fck { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <4>; + reg = <0x02d8>; +}; |