1 files changed, 0 insertions, 152 deletions
diff --git a/kernel/Documentation/devicetree/bindings/arm/gic.txt b/kernel/Documentation/devicetree/bindings/arm/gic.txt
deleted file mode 100644
index 2da059a47..000000000
--- a/kernel/Documentation/devicetree/bindings/arm/gic.txt
+++ /dev/null
@@ -1,152 +0,0 @@
-* ARM Generic Interrupt Controller
-
-ARM SMP cores are often associated with a GIC, providing per processor
-interrupts (PPI), shared processor interrupts (SPI) and software
-generated interrupts (SGI).
-
-Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
-Secondary GICs are cascaded into the upward interrupt controller and do not
-have PPIs or SGIs.
-
-Main node required properties:
-
-- compatible : should be one of:
-	"arm,gic-400"
-	"arm,cortex-a15-gic"
-	"arm,cortex-a9-gic"
-	"arm,cortex-a7-gic"
-	"arm,arm11mp-gic"
-	"brcm,brahma-b15-gic"
-	"arm,arm1176jzf-devchip-gic"
-	"qcom,msm-8660-qgic"
-	"qcom,msm-qgic2"
-- interrupt-controller : Identifies the node as an interrupt controller
-- #interrupt-cells : Specifies the number of cells needed to encode an
-  interrupt source.  The type shall be a <u32> and the value shall be 3.
-
-  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
-  interrupts.
-
-  The 2nd cell contains the interrupt number for the interrupt type.
-  SPI interrupts are in the range [0-987].  PPI interrupts are in the
-  range [0-15].
-
-  The 3rd cell is the flags, encoded as follows:
-	bits[3:0] trigger type and level flags.
-		1 = low-to-high edge triggered
-		2 = high-to-low edge triggered (invalid for SPIs)
-		4 = active high level-sensitive
-		8 = active low level-sensitive (invalid for SPIs).
-	bits[15:8] PPI interrupt cpu mask.  Each bit corresponds to each of
-	the 8 possible cpus attached to the GIC.  A bit set to '1' indicated
-	the interrupt is wired to that CPU.  Only valid for PPI interrupts.
-	Also note that the configurability of PPI interrupts is IMPLEMENTATION
-	DEFINED and as such not guaranteed to be present (most SoC available
-	in 2014 seem to ignore the setting of this flag and use the hardware
-	default value).
-
-- reg : Specifies base physical address(s) and size of the GIC registers. The
-  first region is the GIC distributor register base and size. The 2nd region is
-  the GIC cpu interface register base and size.
-
-Optional
-- interrupts	: Interrupt source of the parent interrupt controller on
-  secondary GICs, or VGIC maintenance interrupt on primary GIC (see
-  below).
-
-- cpu-offset	: per-cpu offset within the distributor and cpu interface
-  regions, used when the GIC doesn't have banked registers. The offset is
-  cpu-offset * cpu-nr.
-
-Example:
-
-	intc: interrupt-controller@fff11000 {
-		compatible = "arm,cortex-a9-gic";
-		#interrupt-cells = <3>;
-		#address-cells = <1>;
-		interrupt-controller;
-		reg = <0xfff11000 0x1000>,
-		      <0xfff10100 0x100>;
-	};
-
-
-* GIC virtualization extensions (VGIC)
-
-For ARM cores that support the virtualization extensions, additional
-properties must be described (they only exist if the GIC is the
-primary interrupt controller).
-
-Required properties:
-
-- reg : Additional regions specifying the base physical address and
-  size of the VGIC registers. The first additional region is the GIC
-  virtual interface control register base and size. The 2nd additional
-  region is the GIC virtual cpu interface register base and size.
-
-- interrupts : VGIC maintenance interrupt.
-
-Example:
-
-	interrupt-controller@2c001000 {
-		compatible = "arm,cortex-a15-gic";
-		#interrupt-cells = <3>;
-		interrupt-controller;
-		reg = <0x2c001000 0x1000>,
-		      <0x2c002000 0x1000>,
-		      <0x2c004000 0x2000>,
-		      <0x2c006000 0x2000>;
-		interrupts = <1 9 0xf04>;
-	};
-
-
-* GICv2m extension for MSI/MSI-x support (Optional)
-
-Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s).
-This is enabled by specifying v2m sub-node(s).
-
-Required properties:
-
-- compatible	    : The value here should contain "arm,gic-v2m-frame".
-
-- msi-controller    : Identifies the node as an MSI controller.
-
-- reg		    : GICv2m MSI interface register base and size
-
-Optional properties:
-
-- arm,msi-base-spi  : When the MSI_TYPER register contains an incorrect
-  		      value, this property should contain the SPI base of
-		      the MSI frame, overriding the HW value.
-
-- arm,msi-num-spis  : When the MSI_TYPER register contains an incorrect
-  		      value, this property should contain the number of
-		      SPIs assigned to the frame, overriding the HW value.
-
-Example:
-
-	interrupt-controller@e1101000 {
-		compatible = "arm,gic-400";
-		#interrupt-cells = <3>;
-		#address-cells = <2>;
-		#size-cells = <2>;
-		interrupt-controller;
-		interrupts = <1 8 0xf04>;
-		ranges = <0 0 0 0xe1100000 0 0x100000>;
-		reg = <0x0 0xe1110000 0 0x01000>,
-		      <0x0 0xe112f000 0 0x02000>,
-		      <0x0 0xe1140000 0 0x10000>,
-		      <0x0 0xe1160000 0 0x10000>;
-		v2m0: v2m@0x8000 {
-			compatible = "arm,gic-v2m-frame";
-			msi-controller;
-			reg = <0x0 0x80000 0 0x1000>;
-		};
-
-		....
-
-		v2mN: v2m@0x9000 {
-			compatible = "arm,gic-v2m-frame";
-			msi-controller;
-			reg = <0x0 0x90000 0 0x1000>;
-		};
-	};