diff options
Diffstat (limited to 'kernel/Documentation/ABI/testing/sysfs-driver-hid-wiimote')
| -rw-r--r-- | kernel/Documentation/ABI/testing/sysfs-driver-hid-wiimote | 77 |
1 files changed, 77 insertions, 0 deletions
diff --git a/kernel/Documentation/ABI/testing/sysfs-driver-hid-wiimote b/kernel/Documentation/ABI/testing/sysfs-driver-hid-wiimote new file mode 100644 index 000000000..39dfa5cb1 --- /dev/null +++ b/kernel/Documentation/ABI/testing/sysfs-driver-hid-wiimote @@ -0,0 +1,77 @@ +What: /sys/bus/hid/drivers/wiimote/<dev>/led1 +What: /sys/bus/hid/drivers/wiimote/<dev>/led2 +What: /sys/bus/hid/drivers/wiimote/<dev>/led3 +What: /sys/bus/hid/drivers/wiimote/<dev>/led4 +Date: July 2011 +KernelVersion: 3.1 +Contact: David Herrmann <dh.herrmann@googlemail.com> +Description: Make it possible to set/get current led state. Reading from it + returns 0 if led is off and 1 if it is on. Writing 0 to it + disables the led, writing 1 enables it. + +What: /sys/bus/hid/drivers/wiimote/<dev>/extension +Date: August 2011 +KernelVersion: 3.2 +Contact: David Herrmann <dh.herrmann@gmail.com> +Description: This file contains the currently connected and initialized + extensions. It can be one of: none, motionp, nunchuck, classic, + motionp+nunchuck, motionp+classic + motionp is the official Nintendo Motion+ extension, nunchuck is + the official Nintendo Nunchuck extension and classic is the + Nintendo Classic Controller extension. The motionp extension can + be combined with the other two. + Starting with kernel-version 3.11 Motion Plus hotplugging is + supported and if detected, it's no longer reported as static + extension. You will get uevent notifications for the motion-plus + device then. + +What: /sys/bus/hid/drivers/wiimote/<dev>/devtype +Date: May 2013 +KernelVersion: 3.11 +Contact: David Herrmann <dh.herrmann@gmail.com> +Description: While a device is initialized by the wiimote driver, we perform + a device detection and signal a "change" uevent after it is + done. This file shows the detected device type. "pending" means + that the detection is still ongoing, "unknown" means, that the + device couldn't be detected or loaded. "generic" means, that the + device couldn't be detected but supports basic Wii Remote + features and can be used. + Other strings for each device-type are available and may be + added if new device-specific detections are added. + Currently supported are: + gen10: First Wii Remote generation + gen20: Second Wii Remote Plus generation (builtin MP) + balanceboard: Wii Balance Board + +What: /sys/bus/hid/drivers/wiimote/<dev>/bboard_calib +Date: May 2013 +KernelVersion: 3.11 +Contact: David Herrmann <dh.herrmann@gmail.com> +Description: This attribute is only provided if the device was detected as a + balance board. It provides a single line with 3 calibration + values for all 4 sensors. The values are separated by colons and + are each 2 bytes long (encoded as 4 digit hexadecimal value). + First, 0kg values for all 4 sensors are written, followed by the + 17kg values for all 4 sensors and last the 34kg values for all 4 + sensors. + Calibration data is already applied by the kernel to all input + values but may be used by user-space to perform other + transformations. + +What: /sys/bus/hid/drivers/wiimote/<dev>/pro_calib +Date: October 2013 +KernelVersion: 3.13 +Contact: David Herrmann <dh.herrmann@gmail.com> +Description: This attribute is only provided if the device was detected as a + pro-controller. It provides a single line with 4 calibration + values for all 4 analog sticks. Format is: "x1:y1 x2:y2". Data + is prefixed with a +/-. Each value is a signed 16bit number. + Data is encoded as decimal numbers and specifies the offsets of + the analog sticks of the pro-controller. + Calibration data is already applied by the kernel to all input + values but may be used by user-space to perform other + transformations. + Calibration data is detected by the kernel during device setup. + You can write "scan\n" into this file to re-trigger calibration. + You can also write data directly in the form "x1:y1 x2:y2" to + set the calibration values manually. |