Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 449 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/socrates.h b/qemu/roms/u-boot/include/configs/socrates.h
new file mode 100644
index 000000000..c654a0e4e
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/socrates.h
@@ -0,0 +1,449 @@
+/*
+ * (C) Copyright 2008
+ * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
+ *
+ * Wolfgang Denk <wd@denx.de>
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * Socrates
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* new uImage format support */
+#define CONFIG_FIT		1
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_FIT_VERBOSE	1 /* enable fit_format_{error,warning}() */
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE			*/
+#define CONFIG_E500		1	/* BOOKE e500 family		*/
+#define CONFIG_MPC8544		1
+#define CONFIG_SOCRATES		1
+
+#define	CONFIG_SYS_TEXT_BASE	0xfff80000
+
+#define CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+
+#define CONFIG_TSEC_ENET		/* tsec ethernet support	*/
+
+#define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
+#define CONFIG_BOARD_EARLY_INIT_R 1	/* Call board_early_init_r	*/
+
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ *    33000000
+ *    66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz.  In any event, this value
+ * must match the settings of some switches.  Details can be found
+ * in the README.mpc85xxads.
+ */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ	66666666
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache		*/
+#define CONFIG_BTB			/* toggle branch predition	*/
+
+#define CONFIG_SYS_INIT_DBCR DBCR_IDM		/* Enable Debug Exceptions	*/
+
+#undef	CONFIG_SYS_DRAM_TEST			/* memory test, takes time	*/
+#define CONFIG_SYS_MEMTEST_START	0x00400000
+#define CONFIG_SYS_MEMTEST_END		0x00C00000
+
+#define CONFIG_SYS_CCSRBAR		0xE0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+
+/* DDR Setup */
+#define CONFIG_SYS_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x50	/* CTLR 0 DIMM 0 */
+
+#define CONFIG_DDR_DEFAULT_CL	30		/* CAS latency 3	*/
+
+/* Hardcoded values, to use instead of SPD */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000000f
+#define CONFIG_SYS_DDR_CS0_CONFIG		0x80010102
+#define CONFIG_SYS_DDR_TIMING_0		0x00260802
+#define CONFIG_SYS_DDR_TIMING_1		0x3935D322
+#define CONFIG_SYS_DDR_TIMING_2		0x14904CC8
+#define CONFIG_SYS_DDR_MODE			0x00480432
+#define CONFIG_SYS_DDR_INTERVAL		0x030C0100
+#define CONFIG_SYS_DDR_CONFIG_2		0x04400000
+#define CONFIG_SYS_DDR_CONFIG			0xC3008000
+#define CONFIG_SYS_DDR_CLK_CONTROL		0x03800000
+#define CONFIG_SYS_SDRAM_SIZE			256 /* in Megs */
+
+/*
+ * Flash on the LocalBus
+ */
+#define CONFIG_SYS_LBC_CACHE_BASE	0xf0000000	/* Localbus cacheable	 */
+
+#define CONFIG_SYS_FLASH0		0xFE000000
+#define CONFIG_SYS_FLASH1		0xFC000000
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
+
+#define CONFIG_SYS_LBC_FLASH_BASE	CONFIG_SYS_FLASH1	/* Localbus flash start	*/
+#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH	*/
+
+#define CONFIG_SYS_BR0_PRELIM		0xfe001001	/* port size 16bit	*/
+#define CONFIG_SYS_OR0_PRELIM		0xfe000030	/* 32MB Flash		*/
+#define CONFIG_SYS_BR1_PRELIM		0xfc001001	/* port size 16bit	*/
+#define CONFIG_SYS_OR1_PRELIM		0xfe000030	/* 32MB Flash		*/
+
+#define CONFIG_SYS_FLASH_CFI				/* flash is CFI compat.	*/
+#define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver*/
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	256		/* sectors per device	*/
+#undef	CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms)	*/
+
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor	*/
+
+#define CONFIG_SYS_LBC_LCRR		0x00030004    /* LB clock ratio reg	*/
+#define CONFIG_SYS_LBC_LBCR		0x00000000    /* LB config reg		*/
+#define CONFIG_SYS_LBC_LSRT		0x20000000    /* LB sdram refresh timer	*/
+#define CONFIG_SYS_LBC_MRTPR		0x20000000    /* LB refresh timer presc.*/
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address	*/
+#define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(384 * 1024)	/* Reserve 384KiB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(4 << 20)	/* Reserve 4 MB for malloc */
+
+/* FPGA and NAND */
+#define CONFIG_SYS_FPGA_BASE		0xc0000000
+#define CONFIG_SYS_FPGA_SIZE		0x00100000	/* 1 MB		*/
+#define CONFIG_SYS_HMI_BASE		0xc0010000
+#define CONFIG_SYS_BR3_PRELIM		0xc0001881	/* UPMA, 32-bit */
+#define CONFIG_SYS_OR3_PRELIM		0xfff00000	/* 1 MB 	*/
+
+#define CONFIG_SYS_NAND_BASE		(CONFIG_SYS_FPGA_BASE + 0x70)
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_CMD_NAND
+
+/* LIME GDC */
+#define CONFIG_SYS_LIME_BASE		0xc8000000
+#define CONFIG_SYS_LIME_SIZE		0x04000000	/* 64 MB	*/
+#define CONFIG_SYS_BR2_PRELIM		0xc80018a1	/* UPMB, 32-bit	*/
+#define CONFIG_SYS_OR2_PRELIM		0xfc000000	/* 64 MB	*/
+
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_MB862xx
+#define CONFIG_VIDEO_MB862xx_ACCEL
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CONSOLE_EXTRA_INFO
+#define VIDEO_FB_16BPP_PIXEL_SWAP
+#define VIDEO_FB_16BPP_WORD_SWAP
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(2 << 20)	/* decompressed img */
+
+/* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */
+#define CONFIG_SYS_MB862xx_CCF		0x10000
+/* SDRAM parameter */
+#define CONFIG_SYS_MB862xx_MMR		0x4157BA63
+
+/* Serial Port */
+
+#define CONFIG_CONS_INDEX     1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+#define CONFIG_BAUDRATE         115200
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_AUTO_COMPLETE	1	/* add autocompletion support */
+#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
+
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	102124
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	102124
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+
+/* I2C RTC */
+#define CONFIG_RTC_RX8025		/* Use Epson rx8025 rtc via i2c	*/
+#define CONFIG_SYS_I2C_RTC_ADDR	0x32	/* at address 0x32		*/
+
+/* I2C W83782G HW-Monitoring IC */
+#define CONFIG_SYS_I2C_W83782G_ADDR	0x28	/* W83782G address 		*/
+
+/* I2C temp sensor */
+/* Socrates uses Maxim's	DS75, which is compatible with LM75 */
+#define CONFIG_DTT_LM75		1
+#define CONFIG_DTT_SENSORS	{4}		/* Sensor addresses	*/
+#define CONFIG_SYS_DTT_MAX_TEMP	125
+#define CONFIG_SYS_DTT_LOW_TEMP	-55
+#define CONFIG_SYS_DTT_HYSTERESIS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1.
+ */
+#define CONFIG_SYS_PCI_PHYS		0x80000000	/* 1G PCI TLB */
+
+/* PCI is clocked by the external source at 33 MHz */
+#define CONFIG_PCI_CLK_FREQ	33000000
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M			*/
+#define CONFIG_SYS_PCI1_IO_BASE	0xE2000000
+#define CONFIG_SYS_PCI1_IO_PHYS	CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE	0x01000000	/* 16M			*/
+
+#if defined(CONFIG_PCI)
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
+#endif	/* CONFIG_PCI */
+
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_TSEC1	1
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"TSEC1"
+#undef CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR		0
+#define TSEC3_PHY_ADDR		1
+
+#define TSEC1_PHYIDX		0
+#define TSEC3_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC3_FLAGS		TSEC_GIGABIT
+
+/* Options are: TSEC[0,1] */
+#define CONFIG_ETHPRIME		"TSEC0"
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env	*/
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x4000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define	CONFIG_TIMESTAMP		/* Print image info with ts	*/
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BMP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#undef CONFIG_CMD_EEPROM
+#define CONFIG_CMD_EXT2		/* EXT2 Support			*/
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_MII
+#undef CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_PCI)
+    #define CONFIG_CMD_PCI
+#endif
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address		*/
+
+#if defined(CONFIG_CMD_KGDB)
+    #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+    #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size	*/
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux	*/
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port*/
+#endif
+
+
+#define CONFIG_LOADADDR	 200000		/* default addr for tftp & bootm*/
+
+#define CONFIG_BOOTDELAY 1		/* -1 disables auto-boot	*/
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Welcome on the ABB Socrates Board;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs	*/
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"consdev=ttyS0\0"						\
+	"uboot_file=/home/tftp/syscon3/u-boot.bin\0"			\
+	"bootfile=/home/tftp/syscon3/uImage\0"				\
+	"fdt_file=/home/tftp/syscon3/socrates.dtb\0"			\
+	"initrd_file=/home/tftp/syscon3/uinitrd.gz\0"			\
+	"uboot_addr=FFFA0000\0"						\
+	"kernel_addr=FE000000\0"					\
+	"fdt_addr=FE1E0000\0"						\
+	"ramdisk_addr=FE200000\0"					\
+	"fdt_addr_r=B00000\0"						\
+	"kernel_addr_r=200000\0"					\
+	"ramdisk_addr_r=400000\0"					\
+	"rootpath=/opt/eldk/ppc_85xxDP\0"				\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$serverip:$rootpath\0"				\
+	"addcons=setenv bootargs $bootargs "				\
+		"console=$consdev,$baudrate\0"				\
+	"addip=setenv bootargs $bootargs "				\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask"		\
+		":$hostname:$netdev:off panic=1\0"			\
+	"boot_nor=run ramargs addcons;"					\
+		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
+	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
+		"tftp ${fdt_addr_r} ${fdt_file}; "			\
+		"run nfsargs addip addcons;"				\
+		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
+	"update_uboot=tftp 100000 ${uboot_file};"			\
+		"protect off fffa0000 ffffffff;"			\
+		"era fffa0000 ffffffff;"				\
+		"cp.b 100000 fffa0000 ${filesize};"			\
+		"setenv filesize;saveenv\0"				\
+	"update_kernel=tftp 100000 ${bootfile};"			\
+		"era fe000000 fe1dffff;"				\
+		"cp.b 100000 fe000000 ${filesize};"			\
+		"setenv filesize;saveenv\0"				\
+	"update_fdt=tftp 100000 ${fdt_file};" 				\
+		"era fe1e0000 fe1fffff;"				\
+		"cp.b 100000 fe1e0000 ${filesize};"			\
+		"setenv filesize;saveenv\0"				\
+	"update_initrd=tftp 100000 ${initrd_file};" 			\
+		"era fe200000 fe9fffff;"				\
+		"cp.b 100000 fe200000 ${filesize};"			\
+		"setenv filesize;saveenv\0"				\
+	"clean_data=era fea00000 fff5ffff\0"				\
+	"usbargs=setenv bootargs root=/dev/sda1 rw\0" 			\
+	"load_usb=usb start;" 						\
+		"ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0"	\
+	"boot_usb=run load_usb usbargs addcons;"			\
+		"bootm ${kernel_addr_r} - ${fdt_addr};"			\
+		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
+	""
+#define CONFIG_BOOTCOMMAND	"run boot_nor"
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+/* USB support */
+#define CONFIG_USB_OHCI_NEW		1
+#define CONFIG_PCI_OHCI			1
+#define CONFIG_PCI_OHCI_DEVNO		3 /* Number in PCI list */
+#define CONFIG_PCI_EHCI_DEVNO		(CONFIG_PCI_OHCI_DEVNO / 2)
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME		"ohci_pci"
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	1
+#define CONFIG_DOS_PARTITION		1
+#define CONFIG_USB_STORAGE		1
+
+#endif	/* __CONFIG_H */