Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 146 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/cm-bf548.h b/qemu/roms/u-boot/include/configs/cm-bf548.h
new file mode 100644
index 000000000..346e27f3e
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/cm-bf548.h
@@ -0,0 +1,146 @@
+/*
+ * U-boot - Configuration file for cm-bf548 board
+ */
+
+#ifndef __CONFIG_CM_BF548_H__
+#define __CONFIG_CM_BF548_H__
+
+#include <asm/config-pre.h>
+
+
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU             bf548-0.0
+#define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_PARA
+
+
+/*
+ * Clock Settings
+ *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz					*/
+#define CONFIG_CLKIN_HZ			25000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN		*/
+/*                                                1 = CLKIN / 2		*/
+#define CONFIG_CLKIN_HALF		0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass	*/
+/*                                                1 = bypass PLL	*/
+#define CONFIG_PLL_BYPASS		0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL		*/
+/* Values can range from 0-63 (where 0 means 64)			*/
+#define CONFIG_VCO_MULT			21
+/* CCLK_DIV controls the core clock divider				*/
+/* Values can be 1, 2, 4, or 8 ONLY					*/
+#define CONFIG_CCLK_DIV			1
+/* SCLK_DIV controls the system clock divider				*/
+/* Values can range from 1-15						*/
+#define CONFIG_SCLK_DIV			4
+
+/* Decrease core voltage */
+#define CONFIG_VR_CTL_VAL (VLEV_115 | GAIN_20 | FREQ_1000)
+
+
+/*
+ * Memory Settings
+ */
+#define CONFIG_MEM_ADD_WDTH	10
+#define CONFIG_MEM_SIZE		64
+
+#define CONFIG_EBIU_DDRCTL0_VAL	0x218A83FE
+#define CONFIG_EBIU_DDRCTL1_VAL	0x20022222
+#define CONFIG_EBIU_DDRCTL2_VAL	0x00000021
+
+/* Default bank mapping:
+ *	Async Bank 0 - 32MB Burst Flash
+ *	Async Bank 1 - Ethernet
+ *	Async Bank 2 - Nothing
+ *	Async Bank 3 - Nothing
+ */
+#define CONFIG_EBIU_AMGCTL_VAL	0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL	0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL	0xFFC27BB0
+#define CONFIG_EBIU_FCTL_VAL	(BCLK_4)
+#define CONFIG_EBIU_MODE_VAL	(B0MODE_FLASH)
+
+#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN	(640 * 1024)
+
+
+/*
+ * Network Settings
+ */
+#define ADI_CMDS_NETWORK	1
+#define CONFIG_SMC911X	1
+#define CONFIG_SMC911X_BASE	0x24000000
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_HOSTNAME		cm-bf548
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR	02:80:ad:24:31:91 */
+
+
+/*
+ * Flash Settings
+ */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_BASE		0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	259
+
+
+/*
+ * Env Storage Settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_ADDR		0x20008000
+#define CONFIG_ENV_OFFSET	0x8000
+#define CONFIG_ENV_SIZE		0x8000
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
+
+
+/*
+ * I2C Settings
+ */
+#define CONFIG_BFIN_TWI_I2C	1
+#define CONFIG_HARD_I2C		1
+
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE	1
+#define CONFIG_BOOTCOMMAND	"run flashboot"
+#define FLASHBOOT_ENV_SETTINGS	"flashboot=bootm 0x20040000\0"
+#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
+
+#define CONFIG_ADI_GPIO2
+
+#ifndef __ADSPBF542__
+/* Don't waste time transferring a logo over the UART */
+# if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
+#  define CONFIG_VIDEO
+#  define EASYLOGO_HEADER <asm/bfin_logo_230x230_gzip.h>
+# endif
+# define CONFIG_DEB_DMA_URGENT
+#endif
+
+/* Define if want to do post memory test */
+#undef CONFIG_POST
+#ifdef CONFIG_POST
+#define FLASH_START_POST_BLOCK 11       /* Should > = 11 */
+#define FLASH_END_POST_BLOCK   71       /* Should < = 71 */
+#endif
+
+
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
+
+#endif