Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 296 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/include/configs/FLAGADM.h b/qemu/roms/u-boot/include/configs/FLAGADM.h
new file mode 100644
index 000000000..d93223fa4
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/FLAGADM.h
@@ -0,0 +1,296 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
+#define CONFIG_FLAGADM		1	/* ...on a FLAGA DM	*/
+#define CONFIG_8xx_GCLK_FREQ 48000000	/*48MHz*/
+
+#define	CONFIG_SYS_TEXT_BASE	0x40000000
+
+#undef	CONFIG_8xx_CONS_SMC1		/* Console is on SMC1		*/
+#define CONFIG_8xx_CONS_SMC2	1
+#undef	CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
+#define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds	*/
+
+#undef	CONFIG_CLOCKS_IN_MHZ
+
+#if 0
+#define CONFIG_BOOTARGS		"root=/dev/nfs rw ip=bootp"
+#define CONFIG_BOOTCOMMAND							\
+   "setenv bootargs root=/dev/ram ip=off panic=1;"     \
+   "bootm 40040000 400e0000"
+#else
+#define CONFIG_BOOTARGS		"root=/dev/nfs rw ip=bootp panic=1"
+#define CONFIG_BOOTCOMMAND	"bootp 0x400000; bootm 0x400000"
+#endif /* 0|1*/
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+/*#define	CONFIG_WATCHDOG*/	/* watchdog enabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_NET
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"EEG> "		/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CONFIG_SYS_MEMTEST_START	0x0100000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0f00000	/* 1 ... 15 MB in DRAM	*/
+
+#define CONFIG_SYS_LOAD_ADDR		0x40040000	/* default load address */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CONFIG_SYS_IMMR		0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0x40000000
+#define CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	8000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CONFIG_ENV_IS_IN_FLASH	1
+/* This is a litlebit wasteful, but one sector is 128kb and we have to
+ * assigne a whole sector for the environment, so that we can safely
+ * erase and write it without disturbing the boot sector
+ */
+#define CONFIG_ENV_OFFSET		0x20000 /*   Offset   of Environment Sector	*/
+#define CONFIG_ENV_SIZE		0x20000 /* Total Size of Environment Sector	*/
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#endif
+#define CONFIG_SYS_DELAYED_ICACHE	1	/* enable ICache not before
+						 * running in RAM.
+						 */
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#ifdef CONFIG_WATCHDOG
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
+#else
+#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CONFIG_SYS_PRE_SIUMCR (SIUMCR_DBGC11 | SIUMCR_MPRE | \
+							SIUMCR_MLRC01 | SIUMCR_GB5E)
+#define CONFIG_SYS_SIUMCR (CONFIG_SYS_PRE_SIUMCR | SIUMCR_DLK)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control				11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register		11-27
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit miltiplier of 0x00b i.e. operation clock is
+ * 4MHz * (0x00b+1) = 4MHz * 12 =  48MHz
+ */
+#define CONFIG_SYS_PLPRCR	(0x00b00000 | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register		15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK	SCCR_EBDF11
+#define CONFIG_SYS_SCCR	( SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
+			 SCCR_DFALCD00)
+
+#define CONFIG_SYS_DER 0
+
+/*
+ * In the Flaga DM we have:
+ * Flash on BR0/OR0/CS0a at 0x40000000
+ * Display on BR1/OR1/CS1 at 0x20000000
+ * SDRAM on BR2/OR2/CS2 at 0x00000000
+ * Free BR3/OR3/CS3
+ * DSP1 on BR4/OR4/CS4 at 0x80000000
+ * DSP2 on BR5/OR5/CS5 at 0xa0000000
+ *
+ * For now we just configure the Flash and the SDRAM and leave the others
+ * untouched.
+*/
+
+#define CONFIG_SYS_FLASH_PROTECTION 0
+
+#define FLASH_BASE0		0x40000000	/* FLASH bank #0	*/
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CONFIG_SYS_OR_AM		0xff000000	/* OR addr mask */
+#define CONFIG_SYS_OR_ATM		0x00006000
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1	*/
+#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | \
+				 OR_SCY_3_CLK | OR_TRLX | OR_EHTR )
+
+#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_OR_AM | CONFIG_SYS_OR_ATM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0 & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+/*
+ * BR2 and OR2 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2			0x00000000	/* SDRAM bank #0	*/
+#define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
+#define CONFIG_SYS_OR_TIMING_SDRAM	( 0x00000800 )
+
+#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM)
+#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2 & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#define CONFIG_SYS_BR2			CONFIG_SYS_BR2_PRELIM
+#define CONFIG_SYS_OR2			CONFIG_SYS_OR2_PRELIM
+
+/*
+ * MAMR settings for SDRAM
+ */
+#define CONFIG_SYS_MAMR_48_SDR (CONFIG_SYS_MAMR_PTA |	 MAMR_WLFA_1X | MAMR_RLFA_1X  \
+					| MAMR_G0CLA_A11)
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CONFIG_SYS_MAMR_PTA	0x0F000000
+
+/*
+   * BR4 and OR4 (DSP1)
+   *
+   * We do not wan't preliminary setup of the DSP, anyway we need the
+   * UPMB setup correctly before we can access the DSP.
+   *
+*/
+#define DSP_BASE 0x80000000
+
+#define CONFIG_SYS_OR4 ( OR_AM_MSK | OR_CSNT_SAM | OR_BI | OR_G5LS)
+#define CONFIG_SYS_BR4 ( (DSP_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_UPMB | BR_V )
+
+#endif	/* __CONFIG_H */