summaryrefslogtreecommitdiffstats
path: root/qemu/roms/u-boot/doc/README.memory-test
diff options
context:
space:
mode:
authorYang Zhang <yang.z.zhang@intel.com>2015-08-28 09:58:54 +0800
committerYang Zhang <yang.z.zhang@intel.com>2015-09-01 12:44:00 +0800
commite44e3482bdb4d0ebde2d8b41830ac2cdb07948fb (patch)
tree66b09f592c55df2878107a468a91d21506104d3f /qemu/roms/u-boot/doc/README.memory-test
parent9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00 (diff)
Add qemu 2.4.0
Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Diffstat (limited to 'qemu/roms/u-boot/doc/README.memory-test')
-rw-r--r--qemu/roms/u-boot/doc/README.memory-test98
1 files changed, 98 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/doc/README.memory-test b/qemu/roms/u-boot/doc/README.memory-test
new file mode 100644
index 000000000..eb60e8d83
--- /dev/null
+++ b/qemu/roms/u-boot/doc/README.memory-test
@@ -0,0 +1,98 @@
+The most frequent cause of problems when porting U-Boot to new
+hardware, or when using a sloppy port on some board, is memory errors.
+In most cases these are not caused by failing hardware, but by
+incorrect initialization of the memory controller. So it appears to
+be a good idea to always test if the memory is working correctly,
+before looking for any other potential causes of any problems.
+
+U-Boot implements 3 different approaches to perform memory tests:
+
+1. The get_ram_size() function (see "common/memsize.c").
+
+ This function is supposed to be used in each and every U-Boot port
+ determine the presence and actual size of each of the potential
+ memory banks on this piece of hardware. The code is supposed to be
+ very fast, so running it for each reboot does not hurt. It is a
+ little known and generally underrated fact that this code will also
+ catch 99% of hardware related (i. e. reliably reproducible) memory
+ errors. It is strongly recommended to always use this function, in
+ each and every port of U-Boot.
+
+2. The "mtest" command.
+
+ This is probably the best known memory test utility in U-Boot.
+ Unfortunately, it is also the most problematic, and the most
+ useless one.
+
+ There are a number of serious problems with this command:
+
+ - It is terribly slow. Running "mtest" on the whole system RAM
+ takes a _long_ time before there is any significance in the fact
+ that no errors have been found so far.
+
+ - It is difficult to configure, and to use. And any errors here
+ will reliably crash or hang your system. "mtest" is dumb and has
+ no knowledge about memory ranges that may be in use for other
+ purposes, like exception code, U-Boot code and data, stack,
+ malloc arena, video buffer, log buffer, etc. If you let it, it
+ will happily "test" all such areas, which of course will cause
+ some problems.
+
+ - It is not easy to configure and use, and a large number of
+ systems are seriously misconfigured. The original idea was to
+ test basically the whole system RAM, with only exempting the
+ areas used by U-Boot itself - on most systems these are the areas
+ used for the exception vectors (usually at the very lower end of
+ system memory) and for U-Boot (code, data, etc. - see above;
+ these are usually at the very upper end of system memory). But
+ experience has shown that a very large number of ports use
+ pretty much bogus settings of CONFIG_SYS_MEMTEST_START and
+ CONFIG_SYS_MEMTEST_END; this results in useless tests (because
+ the ranges is too small and/or badly located) or in critical
+ failures (system crashes).
+
+ Because of these issues, the "mtest" command is considered depre-
+ cated. It should not be enabled in most normal ports of U-Boot,
+ especially not in production. If you really need a memory test,
+ then see 1. and 3. above resp. below.
+
+3. The most thorough memory test facility is available as part of the
+ POST (Power-On Self Test) sub-system, see "post/drivers/memory.c".
+
+ If you really need to perform memory tests (for example, because
+ it is mandatory part of your requirement specification), then
+ enable this test which is generic and should work on all archi-
+ tectures.
+
+WARNING:
+
+It should pointed out that _all_ these memory tests have one
+fundamental, unfixable design flaw: they are based on the assumption
+that memory errors can be found by writing to and reading from memory.
+Unfortunately, this is only true for the relatively harmless, usually
+static errors like shorts between data or address lines, unconnected
+pins, etc. All the really nasty errors which will first turn your
+hair gray, only to make you tear it out later, are dynamical errors,
+which usually happen not with simple read or write cycles on the bus,
+but when performing back-to-back data transfers in burst mode. Such
+accesses usually happen only for certain DMA operations, or for heavy
+cache use (instruction fetching, cache flushing). So far I am not
+aware of any freely available code that implements a generic, and
+efficient, memory test like that. The best known test case to stress
+a system like that is to boot Linux with root file system mounted over
+NFS, and then build some larger software package natively (say,
+compile a Linux kernel on the system) - this will cause enough context
+switches, network traffic (and thus DMA transfers from the network
+controller), varying RAM use, etc. to trigger any weak spots in this
+area.
+
+Note: An attempt was made once to implement such a test to catch
+memory problems on a specific board. The code is pretty much board
+specific (for example, it includes setting specific GPIO signals to
+provide triggers for an attached logic analyzer), but you can get an
+idea how it works: see "examples/standalone/test_burst*".
+
+Note 2: Ironically enough, the "test_burst" did not catch any RAM
+errors, not a single one ever. The problems this code was supposed
+to catch did not happen when accessing the RAM, but when reading from
+NOR flash.