summaryrefslogtreecommitdiffstats
path: root/qemu/roms/u-boot/board/zeus
diff options
context:
space:
mode:
authorYang Zhang <yang.z.zhang@intel.com>2015-08-28 09:58:54 +0800
committerYang Zhang <yang.z.zhang@intel.com>2015-09-01 12:44:00 +0800
commite44e3482bdb4d0ebde2d8b41830ac2cdb07948fb (patch)
tree66b09f592c55df2878107a468a91d21506104d3f /qemu/roms/u-boot/board/zeus
parent9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00 (diff)
Add qemu 2.4.0
Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5 Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Diffstat (limited to 'qemu/roms/u-boot/board/zeus')
-rw-r--r--qemu/roms/u-boot/board/zeus/Makefile8
-rw-r--r--qemu/roms/u-boot/board/zeus/README73
-rw-r--r--qemu/roms/u-boot/board/zeus/update.c89
-rw-r--r--qemu/roms/u-boot/board/zeus/zeus.c410
4 files changed, 580 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/zeus/Makefile b/qemu/roms/u-boot/board/zeus/Makefile
new file mode 100644
index 000000000..aa3658a37
--- /dev/null
+++ b/qemu/roms/u-boot/board/zeus/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2007
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y = zeus.o update.o
diff --git a/qemu/roms/u-boot/board/zeus/README b/qemu/roms/u-boot/board/zeus/README
new file mode 100644
index 000000000..1848d8cd3
--- /dev/null
+++ b/qemu/roms/u-boot/board/zeus/README
@@ -0,0 +1,73 @@
+
+Storage of the board specific values (ethaddr...)
+-------------------------------------------------
+
+The board specific environment variables that should be unique
+for each individual board, can be stored in the I2C EEPROM. This
+will be done from offset 0x80 with the length of 0x80 bytes. The
+following command can be used to store the values here:
+
+=> setdef de:20:6a:ed:e2:72 de:20:6a:ed:e2:73 AB0001
+
+ ethaddr eth1addr serial#
+
+Now those 3 values are stored into the I2C EEPROM. A CRC is added
+to make sure that the values get not corrupted.
+
+
+SW-Reset Pushbutton handling:
+-----------------------------
+
+The SW-reset push button is connected to a GPIO input too. This
+way U-Boot can "see" how long the SW-reset was pressed, and a
+specific action can be taken. Two different actions are supported:
+
+a) Release after more than 5 seconds and less then 10 seconds:
+ -> Run POST
+
+ Please note, that the POST test will take a while (approx. 1 min
+ on the 128MByte board). This is mainly due to the system memory
+ test.
+
+b) Release after more than 10 seconds:
+ -> Restore factory default settings
+
+ The factory default values are restored. The default environment
+ variables are restored (ipaddr, serverip...) and the board
+ specific values (ethaddr, eth1addr and serial#) are restored
+ to the environment from the I2C EEPROM. Also a bootline parameter
+ is added to the Linux bootline to signal the Linux kernel upon
+ the next startup, that the factory defaults should be restored.
+
+The command to check this sw-reset status and act accordingly is
+
+=> chkreset
+
+This command is added to the default "bootcmd", so that it is called
+automatically upon startup.
+
+Also, the 2 LED's are used to indicate the current status of this
+command (time passed since pushing the button). When the POST test
+will be run, the green LED will be switched off, and when the
+factory restore will be initiated, the reg LED will be switched off.
+
+
+Loggin of POST results:
+-----------------------
+
+The results of the POST tests are logged in a logbuffer located at the end
+of the onboard memory. It can be accessed with the U-Boot command "log":
+
+=> log show
+<4>POST memory PASSED
+<4>POST cache PASSED
+<4>POST cpu PASSED
+<4>POST uart PASSED
+<4>POST ethernet PASSED
+
+The DENX Linux kernel tree has support for this log buffer included. Exactly
+this buffer is used for logging of all kernel messages too. By enabling the
+compile time option "CONFIG_LOGBUFFER" this support is enabled. This way you
+can access the U-Boot log messages from Linux too.
+
+2007-08-10, Stefan Roese <sr@denx.de>
diff --git a/qemu/roms/u-boot/board/zeus/update.c b/qemu/roms/u-boot/board/zeus/update.c
new file mode 100644
index 000000000..ac738ef2a
--- /dev/null
+++ b/qemu/roms/u-boot/board/zeus/update.c
@@ -0,0 +1,89 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/ppc4xx-gpio.h>
+#include <i2c.h>
+
+#if defined(CONFIG_ZEUS)
+
+u8 buf_zeus_ce[] = {
+/*00 01 02 03 04 05 06 07 */
+ 0x05, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/*08 09 0a 0b 0c 0d 0e 0f */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/*10 11 12 13 14 15 16 17 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/*18 19 1a 1b 1c 1d 1e 1f */
+ 0x00, 0xc0, 0x50, 0x12, 0x72, 0x3e, 0x00, 0x00 };
+
+u8 buf_zeus_pe[] = {
+
+/* CPU_CLOCK_DIV 1 = 00
+ CPU_PLB_FREQ_DIV 3 = 10
+ OPB_PLB_FREQ_DIV 2 = 01
+ EBC_PLB_FREQ_DIV 2 = 00
+ MAL_PLB_FREQ_DIV 1 = 00
+ PCI_PLB_FRQ_DIV 3 = 10
+ PLL_PLLOUTA = IS SET
+ PLL_OPERATING = IS NOT SET
+ PLL_FDB_MUL 10 = 1010
+ PLL_FWD_DIV_A 3 = 101
+ PLL_FWD_DIV_B 3 = 101
+ TUNE = 0x2be */
+/*00 01 02 03 04 05 06 07 */
+ 0x05, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/*08 09 0a 0b 0c 0d 0e 0f */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/*10 11 12 13 14 15 16 17 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+/*18 19 1a 1b 1c 1d 1e 1f */
+ 0x00, 0x60, 0x68, 0x2d, 0x42, 0xbe, 0x00, 0x00 };
+
+static int update_boot_eeprom(void)
+{
+ u32 len = 0x20;
+ u8 chip = CONFIG_SYS_I2C_EEPROM_ADDR;
+ u8 *pbuf;
+ u8 base;
+ int i;
+
+ if (in_be32((void *)GPIO0_IR) & GPIO_VAL(CONFIG_SYS_GPIO_ZEUS_PE)) {
+ pbuf = buf_zeus_pe;
+ base = 0x40;
+ } else {
+ pbuf = buf_zeus_ce;
+ base = 0x00;
+ }
+
+ for (i = 0; i < len; i++, base++) {
+ if (i2c_write(chip, base, 1, &pbuf[i], 1) != 0) {
+ printf("i2c_write fail\n");
+ return 1;
+ }
+ udelay(11000);
+ }
+
+ return 0;
+}
+
+int do_update_boot_eeprom(cmd_tbl_t* cmdtp, int flag, int argc, char * const argv[])
+{
+ return update_boot_eeprom();
+}
+
+U_BOOT_CMD (
+ update_boot_eeprom, 1, 1, do_update_boot_eeprom,
+ "update boot eeprom content",
+ ""
+);
+
+#endif
diff --git a/qemu/roms/u-boot/board/zeus/zeus.c b/qemu/roms/u-boot/board/zeus/zeus.c
new file mode 100644
index 000000000..e2b12f677
--- /dev/null
+++ b/qemu/roms/u-boot/board/zeus/zeus.c
@@ -0,0 +1,410 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <malloc.h>
+#include <environment.h>
+#include <logbuff.h>
+#include <post.h>
+
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/ppc4xx-gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define REBOOT_MAGIC 0x07081967
+#define REBOOT_NOP 0x00000000
+#define REBOOT_DO_POST 0x00000001
+
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+
+ulong flash_get_size(ulong base, int banknum);
+void env_crc_update(void);
+
+static u32 start_time;
+
+int board_early_init_f(void)
+{
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0ER, 0x00000000); /* disable all ints */
+ mtdcr(UIC0CR, 0x00000000);
+ mtdcr(UIC0PR, 0xFFFF7F00); /* set int polarities */
+ mtdcr(UIC0TR, 0x00000000); /* set int trigger levels */
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
+
+ /*
+ * Configure CPC0_PCI to enable PerWE as output
+ */
+ mtdcr(CPC0_PCI, CPC0_PCI_SPE);
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u32 pbcr;
+ int size_val = 0;
+ u32 post_magic;
+ u32 post_val;
+
+ post_magic = in_be32((void *)CONFIG_SYS_POST_MAGIC);
+ post_val = in_be32((void *)CONFIG_SYS_POST_VAL);
+ if ((post_magic == REBOOT_MAGIC) && (post_val == REBOOT_DO_POST)) {
+ /*
+ * Set special bootline bootparameter to pass this POST boot
+ * mode to Linux to reset the username/password
+ */
+ setenv("addmisc", "setenv bootargs \\${bootargs} factory_reset=yes");
+
+ /*
+ * Normally don't run POST tests, only when enabled
+ * via the sw-reset button. So disable further tests
+ * upon next bootup here.
+ */
+ out_be32((void *)CONFIG_SYS_POST_VAL, REBOOT_NOP);
+ } else {
+ /*
+ * Only run POST when initiated via the sw-reset button mechanism
+ */
+ post_word_store(0);
+ }
+
+ /*
+ * Get current time
+ */
+ start_time = get_timer(0);
+
+ /*
+ * FLASH stuff...
+ */
+
+ /* Re-do sizing to get full correct info */
+
+ /* adjust flash start and offset */
+ mfebc(PB0CR, pbcr);
+ switch (gd->bd->bi_flashsize) {
+ case 1 << 20:
+ size_val = 0;
+ break;
+ case 2 << 20:
+ size_val = 1;
+ break;
+ case 4 << 20:
+ size_val = 2;
+ break;
+ case 8 << 20:
+ size_val = 3;
+ break;
+ case 16 << 20:
+ size_val = 4;
+ break;
+ case 32 << 20:
+ size_val = 5;
+ break;
+ case 64 << 20:
+ size_val = 6;
+ break;
+ case 128 << 20:
+ size_val = 7;
+ break;
+ }
+ pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
+ mtebc(PB0CR, pbcr);
+
+ /*
+ * Re-check to get correct base address
+ */
+ flash_get_size(gd->bd->bi_flashstart, 0);
+
+ /* Monitor protection ON by default */
+ (void)flash_protect(FLAG_PROTECT_SET,
+ -CONFIG_SYS_MONITOR_LEN,
+ 0xffffffff,
+ &flash_info[0]);
+
+ /* Env protection ON by default */
+ (void)flash_protect(FLAG_PROTECT_SET,
+ CONFIG_ENV_ADDR_REDUND,
+ CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
+ &flash_info[0]);
+
+ return 0;
+}
+
+/*
+ * Check Board Identity:
+ */
+int checkboard(void)
+{
+ char buf[64];
+ int i = getenv_f("serial#", buf, sizeof(buf));
+
+ puts("Board: Zeus-");
+
+ if (in_be32((void *)GPIO0_IR) & GPIO_VAL(CONFIG_SYS_GPIO_ZEUS_PE))
+ puts("PE");
+ else
+ puts("CE");
+
+ puts(" of BulletEndPoint");
+
+ if (i > 0) {
+ puts(", serial# ");
+ puts(buf);
+ }
+ putc('\n');
+
+ /* both LED's off */
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_RED, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_GREEN, 0);
+ udelay(10000);
+ /* and on again */
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_RED, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_GREEN, 1);
+
+ return (0);
+}
+
+static int default_env_var(char *buf, char *var)
+{
+ char *ptr;
+ char *val;
+
+ /*
+ * Find env variable
+ */
+ ptr = strstr(buf + 4, var);
+ if (ptr == NULL) {
+ printf("ERROR: %s not found!\n", var);
+ return -1;
+ }
+ ptr += strlen(var) + 1;
+
+ /*
+ * Now the ethaddr needs to be updated in the "normal"
+ * environment storage -> redundant flash.
+ */
+ val = ptr;
+ setenv(var, val);
+ printf("Updated %s from eeprom to %s!\n", var, val);
+
+ return 0;
+}
+
+static int restore_default(void)
+{
+ char *buf;
+ char *buf_save;
+ u32 crc;
+
+ set_default_env("");
+
+ gd->env_valid = 1;
+
+ /*
+ * Read board specific values from I2C EEPROM
+ * and set env variables accordingly
+ * -> ethaddr, eth1addr, serial#
+ */
+ buf = buf_save = malloc(FACTORY_RESET_ENV_SIZE);
+ if (buf == NULL) {
+ printf("ERROR: malloc() failed\n");
+ return -1;
+ }
+ if (eeprom_read(FACTORY_RESET_I2C_EEPROM, FACTORY_RESET_ENV_OFFS,
+ (u8 *)buf, FACTORY_RESET_ENV_SIZE)) {
+ puts("\nError reading EEPROM!\n");
+ } else {
+ crc = crc32(0, (u8 *)(buf + 4), FACTORY_RESET_ENV_SIZE - 4);
+ if (crc != *(u32 *)buf) {
+ printf("ERROR: crc mismatch %08x %08x\n", crc, *(u32 *)buf);
+ return -1;
+ }
+
+ default_env_var(buf, "ethaddr");
+ buf += 8 + 18;
+ default_env_var(buf, "eth1addr");
+ buf += 9 + 18;
+ default_env_var(buf, "serial#");
+ }
+
+ /*
+ * Finally save updated env variables back to flash
+ */
+ saveenv();
+
+ free(buf_save);
+
+ return 0;
+}
+
+int do_set_default(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ char *buf;
+ char *buf_save;
+ char str[32];
+ u32 crc;
+ char var[32];
+
+ if (argc < 4) {
+ puts("ERROR!\n");
+ return -1;
+ }
+
+ buf = buf_save = malloc(FACTORY_RESET_ENV_SIZE);
+ memset(buf, 0, FACTORY_RESET_ENV_SIZE);
+
+ strcpy(var, "ethaddr");
+ printf("Setting %s to %s\n", var, argv[1]);
+ sprintf(str, "%s=%s", var, argv[1]);
+ strcpy(buf + 4, str);
+ buf += strlen(str) + 1;
+
+ strcpy(var, "eth1addr");
+ printf("Setting %s to %s\n", var, argv[2]);
+ sprintf(str, "%s=%s", var, argv[2]);
+ strcpy(buf + 4, str);
+ buf += strlen(str) + 1;
+
+ strcpy(var, "serial#");
+ printf("Setting %s to %s\n", var, argv[3]);
+ sprintf(str, "%s=%s", var, argv[3]);
+ strcpy(buf + 4, str);
+
+ crc = crc32(0, (u8 *)(buf_save + 4), FACTORY_RESET_ENV_SIZE - 4);
+ *(u32 *)buf_save = crc;
+
+ if (eeprom_write(FACTORY_RESET_I2C_EEPROM, FACTORY_RESET_ENV_OFFS,
+ (u8 *)buf_save, FACTORY_RESET_ENV_SIZE)) {
+ puts("\nError writing EEPROM!\n");
+ return -1;
+ }
+
+ free(buf_save);
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ setdef, 4, 1, do_set_default,
+ "write board-specific values to EEPROM (ethaddr...)",
+ "ethaddr eth1addr serial#\n - write board-specific values to EEPROM"
+ );
+
+static inline int sw_reset_pressed(void)
+{
+ return !(in_be32((void *)GPIO0_IR) & GPIO_VAL(CONFIG_SYS_GPIO_SW_RESET));
+}
+
+int do_chkreset(cmd_tbl_t* cmdtp, int flag, int argc, char * const argv[])
+{
+ int delta;
+ int count = 0;
+ int post = 0;
+ int factory_reset = 0;
+
+ if (!sw_reset_pressed()) {
+ printf("SW-Reset already high (Button released)\n");
+ printf("-> No action taken!\n");
+ return 0;
+ }
+
+ printf("Waiting for SW-Reset button to be released.");
+
+ while (1) {
+ delta = get_timer(start_time);
+ if (!sw_reset_pressed())
+ break;
+
+ if ((delta > CONFIG_SYS_TIME_POST) && !post) {
+ printf("\nWhen released now, POST tests will be started.");
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_GREEN, 0);
+ post = 1;
+ }
+
+ if ((delta > CONFIG_SYS_TIME_FACTORY_RESET) && !factory_reset) {
+ printf("\nWhen released now, factory default values"
+ " will be restored.");
+ gpio_write_bit(CONFIG_SYS_GPIO_LED_RED, 0);
+ factory_reset = 1;
+ }
+
+ udelay(1000);
+ if (!(count++ % 1000))
+ printf(".");
+ }
+
+
+ printf("\nSW-Reset Button released after %d milli-seconds!\n", delta);
+
+ if (delta > CONFIG_SYS_TIME_FACTORY_RESET) {
+ printf("Starting factory reset value restoration...\n");
+
+ /*
+ * Restore default setting
+ */
+ restore_default();
+
+ /*
+ * Reset the board for default to become valid
+ */
+ do_reset(NULL, 0, 0, NULL);
+
+ return 0;
+ }
+
+ if (delta > CONFIG_SYS_TIME_POST) {
+ printf("Starting POST configuration...\n");
+
+ /*
+ * Enable POST upon next bootup
+ */
+ out_be32((void *)CONFIG_SYS_POST_MAGIC, REBOOT_MAGIC);
+ out_be32((void *)CONFIG_SYS_POST_VAL, REBOOT_DO_POST);
+ post_bootmode_init();
+
+ /*
+ * Reset the logbuffer for a clean start
+ */
+ logbuff_reset();
+
+ do_reset(NULL, 0, 0, NULL);
+
+ return 0;
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD (
+ chkreset, 1, 1, do_chkreset,
+ "Check for status of SW-reset button and act accordingly",
+ ""
+);
+
+#if defined(CONFIG_POST)
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+ u32 post_magic;
+ u32 post_val;
+
+ post_magic = in_be32((void *)CONFIG_SYS_POST_MAGIC);
+ post_val = in_be32((void *)CONFIG_SYS_POST_VAL);
+
+ if ((post_magic == REBOOT_MAGIC) && (post_val == REBOOT_DO_POST))
+ return 1;
+ else
+ return 0;
+}
+#endif /* CONFIG_POST */