Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

1 files changed, 124 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c b/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c
new file mode 100644
index 000000000..fd602ea7e
--- /dev/null
+++ b/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c
@@ -0,0 +1,124 @@
+/*
+ * Copyright 2009 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
+{
+	i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
+		sizeof(ddr2_spd_eeprom_t));
+}
+
+/*
+ * There are four board-specific SDRAM timing parameters which must be
+ * calculated based on the particular PCB artwork.  These are:
+ *   1.) CPO (Read Capture Delay)
+ *           - TIMING_CFG_2 register
+ *           Source: Calculation based on board trace lengths and
+ *                   chip-specific internal delays.
+ *   2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
+ *           - TIMING_CFG_2 register
+ *           Source: Calculation based on board trace lengths.
+ *                   Unless clock and DQ lanes are very different
+ *                   lengths (>2"), this should be set to the nominal value
+ *                   of 1/2 clock delay.
+ *   3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
+ *           - DDR_SDRAM_CLK_CNTL register
+ *           Source: Signal Integrity Simulations
+ *   4.) 2T Timing on Addr/Ctl
+ *           - TIMING_CFG_2 register
+ *           Source: Signal Integrity Simulations
+ *           Usually only needed with heavy load/very high speed (>DDR2-800)
+ *
+ *     PCB routing on the XPedite5170 is nearly identical to the XPedite5370
+ *     so we use the XPedite5370 settings as a basis for the XPedite5170.
+ */
+
+typedef struct board_memctl_options {
+	uint16_t datarate_mhz_low;
+	uint16_t datarate_mhz_high;
+	uint8_t clk_adjust;
+	uint8_t cpo_override;
+	uint8_t write_data_delay;
+} board_memctl_options_t;
+
+static struct board_memctl_options bopts_ctrl[][2] = {
+	{
+		/* Controller 0 */
+		{
+			/* DDR2 600/667 */
+			.datarate_mhz_low	= 500,
+			.datarate_mhz_high	= 750,
+			.clk_adjust		= 5,
+			.cpo_override		= 8,
+			.write_data_delay	= 2,
+		},
+		{
+			/* DDR2 800 */
+			.datarate_mhz_low	= 750,
+			.datarate_mhz_high	= 850,
+			.clk_adjust		= 5,
+			.cpo_override		= 9,
+			.write_data_delay	= 2,
+		},
+	},
+	{
+		/* Controller 1 */
+		{
+			/* DDR2 600/667 */
+			.datarate_mhz_low	= 500,
+			.datarate_mhz_high	= 750,
+			.clk_adjust		= 5,
+			.cpo_override		= 7,
+			.write_data_delay	= 2,
+		},
+		{
+			/* DDR2 800 */
+			.datarate_mhz_low	= 750,
+			.datarate_mhz_high	= 850,
+			.clk_adjust		= 5,
+			.cpo_override		= 8,
+			.write_data_delay	= 2,
+		},
+	},
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			dimm_params_t *pdimm,
+			unsigned int ctrl_num)
+{
+	struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
+	sys_info_t sysinfo;
+	int i;
+	unsigned int datarate;
+
+	get_sys_info(&sysinfo);
+	datarate = get_ddr_freq(0) / 1000000;
+
+	for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
+		if ((bopts[i].datarate_mhz_low <= datarate) &&
+		    (bopts[i].datarate_mhz_high >= datarate)) {
+			debug("controller %d:\n", ctrl_num);
+			debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
+			debug(" cpo = %d\n", bopts[i].cpo_override);
+			debug(" write_data_delay = %d\n",
+				bopts[i].write_data_delay);
+			popts->clk_adjust = bopts[i].clk_adjust;
+			popts->cpo_override = bopts[i].cpo_override;
+			popts->write_data_delay = bopts[i].write_data_delay;
+		}
+	}
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}