Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

3 files changed, 0 insertions, 465 deletions

diff --git a/qemu/roms/u-boot/board/v38b/Makefile b/qemu/roms/u-boot/board/v38b/Makefile
deleted file mode 100644
index a20a5ef0e..000000000
--- a/qemu/roms/u-boot/board/v38b/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= v38b.o ethaddr.o
diff --git a/qemu/roms/u-boot/board/v38b/ethaddr.c b/qemu/roms/u-boot/board/v38b/ethaddr.c
deleted file mode 100644
index 982998fad..000000000
--- a/qemu/roms/u-boot/board/v38b/ethaddr.c
+++ /dev/null
@@ -1,197 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-
-/* For the V38B board the pin is GPIO_PSC_6 */
-#define GPIO_PIN	GPIO_PSC6_0
-
-#define NO_ERROR	0
-#define ERR_NO_NUMBER	1
-#define ERR_BAD_NUMBER	2
-
-static int is_high(void);
-static int check_device(void);
-static void io_out(int value);
-static void io_input(void);
-static void io_output(void);
-static void init_gpio(void);
-static void read_byte(unsigned char *data);
-static void write_byte(unsigned char command);
-
-void read_2501_memory(unsigned char *psernum, unsigned char *perr);
-void board_get_enetaddr(uchar *enetaddr);
-
-
-static int is_high()
-{
-	return (*((vu_long *) MPC5XXX_WU_GPIO_DATA_I) & GPIO_PIN);
-}
-
-static void io_out(int value)
-{
-	if (value)
-		*((vu_long *) MPC5XXX_WU_GPIO_DATA_O) |= GPIO_PIN;
-	else
-		*((vu_long *) MPC5XXX_WU_GPIO_DATA_O) &= ~GPIO_PIN;
-}
-
-static void io_input()
-{
-	*((vu_long *) MPC5XXX_WU_GPIO_DIR) &= ~GPIO_PIN;
-	udelay(3);	/* allow input to settle */
-}
-
-static void io_output()
-{
-	*((vu_long *) MPC5XXX_WU_GPIO_DIR) |= GPIO_PIN;
-}
-
-static void init_gpio()
-{
-	*((vu_long *) MPC5XXX_WU_GPIO_ENABLE) |= GPIO_PIN;	/* Enable appropriate pin */
-}
-
-void read_2501_memory(unsigned char *psernum, unsigned char *perr)
-{
-#define NBYTES 28
-	unsigned char crcval, i;
-	unsigned char buf[NBYTES];
-
-	*perr = 0;
-	crcval = 0;
-
-	for (i = 0; i < NBYTES; i++)
-		buf[i] = 0;
-
-	if (!check_device())
-		*perr = ERR_NO_NUMBER;
-	else {
-		*perr = NO_ERROR;
-		write_byte(0xCC);		/* skip ROM (0xCC) */
-		write_byte(0xF0);		/* Read memory command 0xF0 */
-		write_byte(0x00);		/* Address TA1=0, TA2=0 */
-		write_byte(0x00);
-		read_byte(&crcval);		/* Read CRC of address and command */
-
-		for (i = 0; i < NBYTES; i++)
-			read_byte(&buf[i]);
-	}
-	if (strncmp((const char *) &buf[11], "MAREL IEEE 802.3", 16)) {
-		*perr = ERR_BAD_NUMBER;
-		psernum[0] = 0x00;
-		psernum[1] = 0xE0;
-		psernum[2] = 0xEE;
-		psernum[3] = 0xFF;
-		psernum[4] = 0xFF;
-		psernum[5] = 0xFF;
-	} else {
-		psernum[0] = 0x00;
-		psernum[1] = 0xE0;
-		psernum[2] = 0xEE;
-		psernum[3] = buf[7];
-		psernum[4] = buf[6];
-		psernum[5] = buf[5];
-	}
-}
-
-static int check_device()
-{
-	int found;
-
-	io_output();
-	io_out(0);
-	udelay(500);  /* must be at least 480 us low pulse */
-
-	io_input();
-	udelay(60);
-
-	found = (is_high() == 0) ? 1 : 0;
-	udelay(500);  /* must be at least 480 us low pulse */
-
-	return found;
-}
-
-static void write_byte(unsigned char command)
-{
-	char i;
-
-	for (i = 0; i < 8; i++) {
-		/* 1 us to 15 us low pulse starts bit slot */
-		/* Start with high pulse for 3 us */
-		io_input();
-		udelay(3);
-
-		io_out(0);
-		io_output();
-		udelay(3);
-
-		if (command & 0x01) {
-			/* 60 us high for 1-bit */
-			io_input();
-			udelay(60);
-		} else
-			/* 60 us low for 0-bit */
-			udelay(60);
-		/*  Leave pin as input */
-		io_input();
-
-		command = command >> 1;
-	}
-}
-
-static void read_byte(unsigned char *data)
-{
-	unsigned char i, rdat = 0;
-
-	for (i = 0; i < 8; i++) {
-		/* read one bit from one-wire device */
-
-		/* 1 - 15 us low starts bit slot */
-		io_out(0);
-		io_output();
-		udelay(0);
-
-		/* allow line to be pulled high */
-		io_input();
-
-		/* delay 10 us */
-		udelay(10);
-
-		/* now sample input status */
-		if (is_high())
-			rdat = (rdat >> 1) | 0x80;
-		else
-			rdat = rdat >> 1;
-
-		udelay(60);	/* at least 60 us */
-	}
-	/* copy the return value */
-	*data = rdat;
-}
-
-void board_get_enetaddr(uchar *enetaddr)
-{
-	unsigned char sn[6], err = NO_ERROR;
-
-	init_gpio();
-
-	read_2501_memory(sn, &err);
-
-	if (err == NO_ERROR) {
-		sprintf((char *)enetaddr, "%02x:%02x:%02x:%02x:%02x:%02x",
-				sn[0], sn[1], sn[2], sn[3], sn[4], sn[5]);
-		printf("MAC address: %s\n", enetaddr);
-		setenv("ethaddr", (char *)enetaddr);
-	} else {
-		sprintf((char *)enetaddr, "00:01:02:03:04:05");
-		printf("Error reading MAC address.\n");
-		printf("Setting default to %s\n", enetaddr);
-		setenv("ethaddr", (char *)enetaddr);
-	}
-}
diff --git a/qemu/roms/u-boot/board/v38b/v38b.c b/qemu/roms/u-boot/board/v38b/v38b.c
deleted file mode 100644
index a33772991..000000000
--- a/qemu/roms/u-boot/board/v38b/v38b.c
+++ /dev/null
@@ -1,260 +0,0 @@
-/*
- * (C) Copyright 2003-2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <net.h>
-#include <asm/processor.h>
-
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start(int hi_addr)
-{
-	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
-	/* unlock mode register */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* precharge all banks */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-#if SDRAM_DDR
-	/* set mode register: extended mode */
-	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
-	__asm__ volatile ("sync");
-
-	/* set mode register: reset DLL */
-	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
-	__asm__ volatile ("sync");
-#endif /* SDRAM_DDR */
-
-	/* precharge all banks */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* auto refresh */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* set mode register */
-	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
-	__asm__ volatile ("sync");
-
-	/* normal operation */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
-	__asm__ volatile ("sync");
-}
-#endif /* !CONFIG_SYS_RAMBOOT */
-
-
-phys_size_t initdram(int board_type)
-{
-	ulong dramsize = 0;
-	ulong dramsize2 = 0;
-	uint svr, pvr;
-
-#ifndef CONFIG_SYS_RAMBOOT
-	ulong test1, test2;
-
-	/* setup SDRAM chip selects */
-	*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e;	/* 2G at 0x0 */
-	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000;	/* disabled */
-	__asm__ volatile ("sync");
-
-	/* setup config registers */
-	*(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
-	*(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
-	__asm__ volatile ("sync");
-
-#if SDRAM_DDR
-	/* set tap delay */
-	*(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
-	__asm__ volatile ("sync");
-#endif /* SDRAM_DDR */
-
-	/* find RAM size using SDRAM CS0 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize = test1;
-	} else
-		dramsize = test2;
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize < (1 << 20))
-		dramsize = 0;
-
-	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0)
-		*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
-	else
-		*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
-
-	/* let SDRAM CS1 start right after CS0 */
-	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
-
-	/* find RAM size using SDRAM CS1 only */
-	if (!dramsize)
-		sdram_start(0);
-	test2 = test1 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
-	if (!dramsize) {
-		sdram_start(1);
-		test2 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
-	}
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize2 = test1;
-	} else
-		dramsize2 = test2;
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize2 < (1 << 20))
-		dramsize2 = 0;
-
-	/* set SDRAM CS1 size according to the amount of RAM found */
-	if (dramsize2 > 0)
-		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize
-			| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
-	else
-		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-
-#else /* CONFIG_SYS_RAMBOOT */
-
-	/* retrieve size of memory connected to SDRAM CS0 */
-	dramsize = *(vu_long *) MPC5XXX_SDRAM_CS0CFG & 0xFF;
-	if (dramsize >= 0x13)
-		dramsize = (1 << (dramsize - 0x13)) << 20;
-	else
-		dramsize = 0;
-
-	/* retrieve size of memory connected to SDRAM CS1 */
-	dramsize2 = *(vu_long *) MPC5XXX_SDRAM_CS1CFG & 0xFF;
-	if (dramsize2 >= 0x13)
-		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
-	else
-		dramsize2 = 0;
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
-	/*
-	 * On MPC5200B we need to set the special configuration delay in the
-	 * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
-	 * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
-	 *
-	 * "The SDelay should be written to a value of 0x00000004. It is
-	 * required to account for changes caused by normal wafer processing
-	 * parameters."
-	 */
-	svr = get_svr();
-	pvr = get_pvr();
-	if ((SVR_MJREV(svr) >= 2) &&
-		(PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
-
-		*(vu_long *) MPC5XXX_SDRAM_SDELAY = 0x04;
-		__asm__ volatile ("sync");
-	}
-
-	return dramsize + dramsize2;
-}
-
-
-int checkboard (void)
-{
-	puts("Board: MarelV38B\n");
-	return 0;
-}
-
-int board_early_init_f(void)
-{
-#ifdef CONFIG_HW_WATCHDOG
-	/*
-	 * Enable and configure the direction (output) of PSC3_9 - watchdog
-	 * reset input. Refer to 7.3.2.2.[1,3,4] of the MPC5200B User's
-	 * Manual.
-	 */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
-#endif /* CONFIG_HW_WATCHDOG */
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	/*
-	 * Now, when we are in RAM, enable flash write access for the
-	 * detection process.  Note that CS_BOOT cannot be cleared when
-	 * executing in flash.
-	 */
-	*(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-
-	/*
-	 * Enable GPIO_WKUP_7 to "read the status of the actual power
-	 * situation". Default direction is input, so no need to set it
-	 * explicitly.
-	 */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WKUP_7;
-	return 0;
-}
-
-extern void board_get_enetaddr(uchar *enetaddr);
-int misc_init_r(void)
-{
-	uchar enetaddr[6];
-
-	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
-		board_get_enetaddr(enetaddr);
-		eth_setenv_enetaddr("ethaddr", enetaddr);
-	}
-
-	return 0;
-}
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-void init_ide_reset(void)
-{
-	debug("init_ide_reset\n");
-
-	/* Configure PSC1_4 as GPIO output for ATA reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
-	/* Deassert reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
-}
-
-
-void ide_set_reset(int idereset)
-{
-	debug("ide_reset(%d)\n", idereset);
-
-	if (idereset) {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
-		/* Make a delay. MPC5200 spec says 25 usec min */
-		udelay(500000);
-	} else
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |=  GPIO_PSC1_4;
-}
-#endif
-
-
-#ifdef CONFIG_HW_WATCHDOG
-void hw_watchdog_reset(void)
-{
-	/*
-	 * MarelV38B has a TPS3705 watchdog. Spec says that to kick the dog
-	 * we need a positive or negative transition on WDI i.e., our PSC3_9.
-	 */
-	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O ^= GPIO_PSC3_9;
-}
-#endif /* CONFIG_HW_WATCHDOG */