Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

3 files changed, 465 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/v38b/Makefile b/qemu/roms/u-boot/board/v38b/Makefile
new file mode 100644
index 000000000..a20a5ef0e
--- /dev/null
+++ b/qemu/roms/u-boot/board/v38b/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2003-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= v38b.o ethaddr.o
diff --git a/qemu/roms/u-boot/board/v38b/ethaddr.c b/qemu/roms/u-boot/board/v38b/ethaddr.c
new file mode 100644
index 000000000..982998fad
--- /dev/null
+++ b/qemu/roms/u-boot/board/v38b/ethaddr.c
@@ -0,0 +1,197 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+
+/* For the V38B board the pin is GPIO_PSC_6 */
+#define GPIO_PIN	GPIO_PSC6_0
+
+#define NO_ERROR	0
+#define ERR_NO_NUMBER	1
+#define ERR_BAD_NUMBER	2
+
+static int is_high(void);
+static int check_device(void);
+static void io_out(int value);
+static void io_input(void);
+static void io_output(void);
+static void init_gpio(void);
+static void read_byte(unsigned char *data);
+static void write_byte(unsigned char command);
+
+void read_2501_memory(unsigned char *psernum, unsigned char *perr);
+void board_get_enetaddr(uchar *enetaddr);
+
+
+static int is_high()
+{
+	return (*((vu_long *) MPC5XXX_WU_GPIO_DATA_I) & GPIO_PIN);
+}
+
+static void io_out(int value)
+{
+	if (value)
+		*((vu_long *) MPC5XXX_WU_GPIO_DATA_O) |= GPIO_PIN;
+	else
+		*((vu_long *) MPC5XXX_WU_GPIO_DATA_O) &= ~GPIO_PIN;
+}
+
+static void io_input()
+{
+	*((vu_long *) MPC5XXX_WU_GPIO_DIR) &= ~GPIO_PIN;
+	udelay(3);	/* allow input to settle */
+}
+
+static void io_output()
+{
+	*((vu_long *) MPC5XXX_WU_GPIO_DIR) |= GPIO_PIN;
+}
+
+static void init_gpio()
+{
+	*((vu_long *) MPC5XXX_WU_GPIO_ENABLE) |= GPIO_PIN;	/* Enable appropriate pin */
+}
+
+void read_2501_memory(unsigned char *psernum, unsigned char *perr)
+{
+#define NBYTES 28
+	unsigned char crcval, i;
+	unsigned char buf[NBYTES];
+
+	*perr = 0;
+	crcval = 0;
+
+	for (i = 0; i < NBYTES; i++)
+		buf[i] = 0;
+
+	if (!check_device())
+		*perr = ERR_NO_NUMBER;
+	else {
+		*perr = NO_ERROR;
+		write_byte(0xCC);		/* skip ROM (0xCC) */
+		write_byte(0xF0);		/* Read memory command 0xF0 */
+		write_byte(0x00);		/* Address TA1=0, TA2=0 */
+		write_byte(0x00);
+		read_byte(&crcval);		/* Read CRC of address and command */
+
+		for (i = 0; i < NBYTES; i++)
+			read_byte(&buf[i]);
+	}
+	if (strncmp((const char *) &buf[11], "MAREL IEEE 802.3", 16)) {
+		*perr = ERR_BAD_NUMBER;
+		psernum[0] = 0x00;
+		psernum[1] = 0xE0;
+		psernum[2] = 0xEE;
+		psernum[3] = 0xFF;
+		psernum[4] = 0xFF;
+		psernum[5] = 0xFF;
+	} else {
+		psernum[0] = 0x00;
+		psernum[1] = 0xE0;
+		psernum[2] = 0xEE;
+		psernum[3] = buf[7];
+		psernum[4] = buf[6];
+		psernum[5] = buf[5];
+	}
+}
+
+static int check_device()
+{
+	int found;
+
+	io_output();
+	io_out(0);
+	udelay(500);  /* must be at least 480 us low pulse */
+
+	io_input();
+	udelay(60);
+
+	found = (is_high() == 0) ? 1 : 0;
+	udelay(500);  /* must be at least 480 us low pulse */
+
+	return found;
+}
+
+static void write_byte(unsigned char command)
+{
+	char i;
+
+	for (i = 0; i < 8; i++) {
+		/* 1 us to 15 us low pulse starts bit slot */
+		/* Start with high pulse for 3 us */
+		io_input();
+		udelay(3);
+
+		io_out(0);
+		io_output();
+		udelay(3);
+
+		if (command & 0x01) {
+			/* 60 us high for 1-bit */
+			io_input();
+			udelay(60);
+		} else
+			/* 60 us low for 0-bit */
+			udelay(60);
+		/*  Leave pin as input */
+		io_input();
+
+		command = command >> 1;
+	}
+}
+
+static void read_byte(unsigned char *data)
+{
+	unsigned char i, rdat = 0;
+
+	for (i = 0; i < 8; i++) {
+		/* read one bit from one-wire device */
+
+		/* 1 - 15 us low starts bit slot */
+		io_out(0);
+		io_output();
+		udelay(0);
+
+		/* allow line to be pulled high */
+		io_input();
+
+		/* delay 10 us */
+		udelay(10);
+
+		/* now sample input status */
+		if (is_high())
+			rdat = (rdat >> 1) | 0x80;
+		else
+			rdat = rdat >> 1;
+
+		udelay(60);	/* at least 60 us */
+	}
+	/* copy the return value */
+	*data = rdat;
+}
+
+void board_get_enetaddr(uchar *enetaddr)
+{
+	unsigned char sn[6], err = NO_ERROR;
+
+	init_gpio();
+
+	read_2501_memory(sn, &err);
+
+	if (err == NO_ERROR) {
+		sprintf((char *)enetaddr, "%02x:%02x:%02x:%02x:%02x:%02x",
+				sn[0], sn[1], sn[2], sn[3], sn[4], sn[5]);
+		printf("MAC address: %s\n", enetaddr);
+		setenv("ethaddr", (char *)enetaddr);
+	} else {
+		sprintf((char *)enetaddr, "00:01:02:03:04:05");
+		printf("Error reading MAC address.\n");
+		printf("Setting default to %s\n", enetaddr);
+		setenv("ethaddr", (char *)enetaddr);
+	}
+}
diff --git a/qemu/roms/u-boot/board/v38b/v38b.c b/qemu/roms/u-boot/board/v38b/v38b.c
new file mode 100644
index 000000000..a33772991
--- /dev/null
+++ b/qemu/roms/u-boot/board/v38b/v38b.c
@@ -0,0 +1,260 @@
+/*
+ * (C) Copyright 2003-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+#include <net.h>
+#include <asm/processor.h>
+
+
+#ifndef CONFIG_SYS_RAMBOOT
+static void sdram_start(int hi_addr)
+{
+	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
+
+	/* unlock mode register */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* precharge all banks */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+#if SDRAM_DDR
+	/* set mode register: extended mode */
+	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+	__asm__ volatile ("sync");
+
+	/* set mode register: reset DLL */
+	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+	__asm__ volatile ("sync");
+#endif /* SDRAM_DDR */
+
+	/* precharge all banks */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* auto refresh */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+	/* set mode register */
+	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+	__asm__ volatile ("sync");
+
+	/* normal operation */
+	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+	__asm__ volatile ("sync");
+}
+#endif /* !CONFIG_SYS_RAMBOOT */
+
+
+phys_size_t initdram(int board_type)
+{
+	ulong dramsize = 0;
+	ulong dramsize2 = 0;
+	uint svr, pvr;
+
+#ifndef CONFIG_SYS_RAMBOOT
+	ulong test1, test2;
+
+	/* setup SDRAM chip selects */
+	*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e;	/* 2G at 0x0 */
+	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000;	/* disabled */
+	__asm__ volatile ("sync");
+
+	/* setup config registers */
+	*(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+	__asm__ volatile ("sync");
+
+#if SDRAM_DDR
+	/* set tap delay */
+	*(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+	__asm__ volatile ("sync");
+#endif /* SDRAM_DDR */
+
+	/* find RAM size using SDRAM CS0 only */
+	sdram_start(0);
+	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
+	sdram_start(1);
+	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize = test1;
+	} else
+		dramsize = test2;
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize < (1 << 20))
+		dramsize = 0;
+
+	/* set SDRAM CS0 size according to the amount of RAM found */
+	if (dramsize > 0)
+		*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
+	else
+		*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+
+	/* let SDRAM CS1 start right after CS0 */
+	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
+
+	/* find RAM size using SDRAM CS1 only */
+	if (!dramsize)
+		sdram_start(0);
+	test2 = test1 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
+	if (!dramsize) {
+		sdram_start(1);
+		test2 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
+	}
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize2 = test1;
+	} else
+		dramsize2 = test2;
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize2 < (1 << 20))
+		dramsize2 = 0;
+
+	/* set SDRAM CS1 size according to the amount of RAM found */
+	if (dramsize2 > 0)
+		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize
+			| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
+	else
+		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+
+#else /* CONFIG_SYS_RAMBOOT */
+
+	/* retrieve size of memory connected to SDRAM CS0 */
+	dramsize = *(vu_long *) MPC5XXX_SDRAM_CS0CFG & 0xFF;
+	if (dramsize >= 0x13)
+		dramsize = (1 << (dramsize - 0x13)) << 20;
+	else
+		dramsize = 0;
+
+	/* retrieve size of memory connected to SDRAM CS1 */
+	dramsize2 = *(vu_long *) MPC5XXX_SDRAM_CS1CFG & 0xFF;
+	if (dramsize2 >= 0x13)
+		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+	else
+		dramsize2 = 0;
+
+#endif /* CONFIG_SYS_RAMBOOT */
+
+	/*
+	 * On MPC5200B we need to set the special configuration delay in the
+	 * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
+	 * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
+	 *
+	 * "The SDelay should be written to a value of 0x00000004. It is
+	 * required to account for changes caused by normal wafer processing
+	 * parameters."
+	 */
+	svr = get_svr();
+	pvr = get_pvr();
+	if ((SVR_MJREV(svr) >= 2) &&
+		(PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
+
+		*(vu_long *) MPC5XXX_SDRAM_SDELAY = 0x04;
+		__asm__ volatile ("sync");
+	}
+
+	return dramsize + dramsize2;
+}
+
+
+int checkboard (void)
+{
+	puts("Board: MarelV38B\n");
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_HW_WATCHDOG
+	/*
+	 * Enable and configure the direction (output) of PSC3_9 - watchdog
+	 * reset input. Refer to 7.3.2.2.[1,3,4] of the MPC5200B User's
+	 * Manual.
+	 */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
+#endif /* CONFIG_HW_WATCHDOG */
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	/*
+	 * Now, when we are in RAM, enable flash write access for the
+	 * detection process.  Note that CS_BOOT cannot be cleared when
+	 * executing in flash.
+	 */
+	*(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
+
+	/*
+	 * Enable GPIO_WKUP_7 to "read the status of the actual power
+	 * situation". Default direction is input, so no need to set it
+	 * explicitly.
+	 */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WKUP_7;
+	return 0;
+}
+
+extern void board_get_enetaddr(uchar *enetaddr);
+int misc_init_r(void)
+{
+	uchar enetaddr[6];
+
+	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
+		board_get_enetaddr(enetaddr);
+		eth_setenv_enetaddr("ethaddr", enetaddr);
+	}
+
+	return 0;
+}
+
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
+void init_ide_reset(void)
+{
+	debug("init_ide_reset\n");
+
+	/* Configure PSC1_4 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
+	/* Deassert reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
+}
+
+
+void ide_set_reset(int idereset)
+{
+	debug("ide_reset(%d)\n", idereset);
+
+	if (idereset) {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
+		/* Make a delay. MPC5200 spec says 25 usec min */
+		udelay(500000);
+	} else
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |=  GPIO_PSC1_4;
+}
+#endif
+
+
+#ifdef CONFIG_HW_WATCHDOG
+void hw_watchdog_reset(void)
+{
+	/*
+	 * MarelV38B has a TPS3705 watchdog. Spec says that to kick the dog
+	 * we need a positive or negative transition on WDI i.e., our PSC3_9.
+	 */
+	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O ^= GPIO_PSC3_9;
+}
+#endif /* CONFIG_HW_WATCHDOG */