Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

4 files changed, 618 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/freescale/mx53loco/Makefile b/qemu/roms/u-boot/board/freescale/mx53loco/Makefile
new file mode 100644
index 000000000..70ac6db1f
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mx53loco/Makefile
@@ -0,0 +1,9 @@
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+# Jason Liu <r64343@freescale.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y			+= mx53loco.o
+obj-$(CONFIG_VIDEO)	+= mx53loco_video.o
diff --git a/qemu/roms/u-boot/board/freescale/mx53loco/imximage.cfg b/qemu/roms/u-boot/board/freescale/mx53loco/imximage.cfg
new file mode 100644
index 000000000..d1c1931e4
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mx53loco/imximage.cfg
@@ -0,0 +1,83 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+DATA 4 0x53fa8554 0x00300000
+DATA 4 0x53fa8558 0x00300040
+DATA 4 0x53fa8560 0x00300000
+DATA 4 0x53fa8564 0x00300040
+DATA 4 0x53fa8568 0x00300040
+DATA 4 0x53fa8570 0x00300000
+DATA 4 0x53fa8574 0x00300000
+DATA 4 0x53fa8578 0x00300000
+DATA 4 0x53fa857c 0x00300040
+DATA 4 0x53fa8580 0x00300040
+DATA 4 0x53fa8584 0x00300000
+DATA 4 0x53fa8588 0x00300000
+DATA 4 0x53fa8590 0x00300040
+DATA 4 0x53fa8594 0x00300000
+DATA 4 0x53fa86f0 0x00300000
+DATA 4 0x53fa86f4 0x00000000
+DATA 4 0x53fa86fc 0x00000000
+DATA 4 0x53fa8714 0x00000000
+DATA 4 0x53fa8718 0x00300000
+DATA 4 0x53fa871c 0x00300000
+DATA 4 0x53fa8720 0x00300000
+DATA 4 0x53fa8724 0x04000000
+DATA 4 0x53fa8728 0x00300000
+DATA 4 0x53fa872c 0x00300000
+DATA 4 0x63fd9088 0x35343535
+DATA 4 0x63fd9090 0x4d444c44
+DATA 4 0x63fd907c 0x01370138
+DATA 4 0x63fd9080 0x013b013c
+DATA 4 0x63fd9018 0x00011740
+DATA 4 0x63fd9000 0xc3190000
+DATA 4 0x63fd900c 0x9f5152e3
+DATA 4 0x63fd9010 0xb68e8a63
+DATA 4 0x63fd9014 0x01ff00db
+DATA 4 0x63fd902c 0x000026d2
+DATA 4 0x63fd9030 0x009f0e21
+DATA 4 0x63fd9008 0x12273030
+DATA 4 0x63fd9004 0x0002002d
+DATA 4 0x63fd901c 0x00008032
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00028031
+DATA 4 0x63fd901c 0x052080b0
+DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd901c 0x0000803a
+DATA 4 0x63fd901c 0x0000803b
+DATA 4 0x63fd901c 0x00028039
+DATA 4 0x63fd901c 0x05208138
+DATA 4 0x63fd901c 0x04008048
+DATA 4 0x63fd9020 0x00005800
+DATA 4 0x63fd9040 0x05380003
+DATA 4 0x63fd9058 0x00022227
+DATA 4 0x63fd901c 0x00000000
diff --git a/qemu/roms/u-boot/board/freescale/mx53loco/mx53loco.c b/qemu/roms/u-boot/board/freescale/mx53loco/mx53loco.c
new file mode 100644
index 000000000..b32a97ff1
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mx53loco/mx53loco.c
@@ -0,0 +1,412 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux-mx53.h>
+#include <asm/arch/clock.h>
+#include <asm/errno.h>
+#include <asm/imx-common/mx5_video.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/gpio.h>
+#include <power/pmic.h>
+#include <dialog_pmic.h>
+#include <fsl_pmic.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+
+#define MX53LOCO_LCD_POWER		IMX_GPIO_NR(3, 24)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static uint32_t mx53_dram_size[2];
+
+phys_size_t get_effective_memsize(void)
+{
+	/*
+	 * WARNING: We must override get_effective_memsize() function here
+	 * to report only the size of the first DRAM bank. This is to make
+	 * U-Boot relocator place U-Boot into valid memory, that is, at the
+	 * end of the first DRAM bank. If we did not override this function
+	 * like so, U-Boot would be placed at the address of the first DRAM
+	 * bank + total DRAM size - sizeof(uboot), which in the setup where
+	 * each DRAM bank contains 512MiB of DRAM would result in placing
+	 * U-Boot into invalid memory area close to the end of the first
+	 * DRAM bank.
+	 */
+	return mx53_dram_size[0];
+}
+
+int dram_init(void)
+{
+	mx53_dram_size[0] = get_ram_size((void *)PHYS_SDRAM_1, 1 << 30);
+	mx53_dram_size[1] = get_ram_size((void *)PHYS_SDRAM_2, 1 << 30);
+
+	gd->ram_size = mx53_dram_size[0] + mx53_dram_size[1];
+
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = mx53_dram_size[0];
+
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = mx53_dram_size[1];
+}
+
+u32 get_board_rev(void)
+{
+	struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
+	struct fuse_bank *bank = &iim->bank[0];
+	struct fuse_bank0_regs *fuse =
+		(struct fuse_bank0_regs *)bank->fuse_regs;
+
+	int rev = readl(&fuse->gp[6]);
+
+	if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR))
+		rev = 0;
+
+	return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
+}
+
+#define UART_PAD_CTRL	(PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+			 PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+
+static void setup_iomux_uart(void)
+{
+	static const iomux_v3_cfg_t uart_pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT11__UART1_RXD_MUX, UART_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT10__UART1_TXD_MUX, UART_PAD_CTRL),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
+}
+
+#ifdef CONFIG_USB_EHCI_MX5
+int board_ehci_hcd_init(int port)
+{
+	/* request VBUS power enable pin, GPIO7_8 */
+	imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
+	gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
+	return 0;
+}
+#endif
+
+static void setup_iomux_fec(void)
+{
+	static const iomux_v3_cfg_t fec_pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
+			PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
+		NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
+		NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
+				PAD_CTL_HYS | PAD_CTL_PKE),
+		NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
+				PAD_CTL_HYS | PAD_CTL_PKE),
+		NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
+		NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
+		NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
+		NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
+				PAD_CTL_HYS | PAD_CTL_PKE),
+		NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
+				PAD_CTL_HYS | PAD_CTL_PKE),
+		NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
+				PAD_CTL_HYS | PAD_CTL_PKE),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[2] = {
+	{MMC_SDHC1_BASE_ADDR},
+	{MMC_SDHC3_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret;
+
+	imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11);
+	gpio_direction_input(IMX_GPIO_NR(3, 11));
+	imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13);
+	gpio_direction_input(IMX_GPIO_NR(3, 13));
+
+	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
+		ret = !gpio_get_value(IMX_GPIO_NR(3, 13));
+	else
+		ret = !gpio_get_value(IMX_GPIO_NR(3, 11));
+
+	return ret;
+}
+
+#define SD_CMD_PAD_CTRL		(PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+				 PAD_CTL_PUS_100K_UP)
+#define SD_PAD_CTRL		(PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
+				 PAD_CTL_DSE_HIGH)
+
+int board_mmc_init(bd_t *bis)
+{
+	static const iomux_v3_cfg_t sd1_pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
+		MX53_PAD_EIM_DA13__GPIO3_13,
+	};
+
+	static const iomux_v3_cfg_t sd2_pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
+				SD_CMD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
+		MX53_PAD_EIM_DA11__GPIO3_11,
+	};
+
+	u32 index;
+	s32 status = 0;
+
+	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+	esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+	for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
+		switch (index) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(sd1_pads,
+							 ARRAY_SIZE(sd1_pads));
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(sd2_pads,
+							 ARRAY_SIZE(sd2_pads));
+			break;
+		default:
+			printf("Warning: you configured more ESDHC controller"
+				"(%d) as supported by the board(2)\n",
+				CONFIG_SYS_FSL_ESDHC_NUM);
+			return status;
+		}
+		status |= fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
+	}
+
+	return status;
+}
+#endif
+
+#define I2C_PAD_CTRL	(PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
+			 PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+
+static void setup_iomux_i2c(void)
+{
+	static const iomux_v3_cfg_t i2c1_pads[] = {
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
+		NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
+	};
+
+	imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads));
+}
+
+static int power_init(void)
+{
+	unsigned int val;
+	int ret;
+	struct pmic *p;
+
+	if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) {
+		ret = pmic_dialog_init(I2C_PMIC);
+		if (ret)
+			return ret;
+
+		p = pmic_get("DIALOG_PMIC");
+		if (!p)
+			return -ENODEV;
+
+		/* Set VDDA to 1.25V */
+		val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V;
+		ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val);
+		if (ret) {
+			printf("Writing to BUCKCORE_REG failed: %d\n", ret);
+			return ret;
+		}
+
+		pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
+		val |= DA9052_SUPPLY_VBCOREGO;
+		ret = pmic_reg_write(p, DA9053_SUPPLY_REG, val);
+		if (ret) {
+			printf("Writing to SUPPLY_REG failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Set Vcc peripheral to 1.30V */
+		ret = pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
+		if (ret) {
+			printf("Writing to BUCKPRO_REG failed: %d\n", ret);
+			return ret;
+		}
+
+		ret = pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
+		if (ret) {
+			printf("Writing to SUPPLY_REG failed: %d\n", ret);
+			return ret;
+		}
+
+		return ret;
+	}
+
+	if (!i2c_probe(CONFIG_SYS_FSL_PMIC_I2C_ADDR)) {
+		ret = pmic_init(I2C_0);
+		if (ret)
+			return ret;
+
+		p = pmic_get("FSL_PMIC");
+		if (!p)
+			return -ENODEV;
+
+		/* Set VDDGP to 1.25V for 1GHz on SW1 */
+		pmic_reg_read(p, REG_SW_0, &val);
+		val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708;
+		ret = pmic_reg_write(p, REG_SW_0, val);
+		if (ret) {
+			printf("Writing to REG_SW_0 failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Set VCC as 1.30V on SW2 */
+		pmic_reg_read(p, REG_SW_1, &val);
+		val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_300V_MC34708;
+		ret = pmic_reg_write(p, REG_SW_1, val);
+		if (ret) {
+			printf("Writing to REG_SW_1 failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Set global reset timer to 4s */
+		pmic_reg_read(p, REG_POWER_CTL2, &val);
+		val = (val & ~TIMER_MASK_MC34708) | TIMER_4S_MC34708;
+		ret = pmic_reg_write(p, REG_POWER_CTL2, val);
+		if (ret) {
+			printf("Writing to REG_POWER_CTL2 failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Set VUSBSEL and VUSBEN for USB PHY supply*/
+		pmic_reg_read(p, REG_MODE_0, &val);
+		val |= (VUSBSEL_MC34708 | VUSBEN_MC34708);
+		ret = pmic_reg_write(p, REG_MODE_0, val);
+		if (ret) {
+			printf("Writing to REG_MODE_0 failed: %d\n", ret);
+			return ret;
+		}
+
+		/* Set SWBST to 5V in auto mode */
+		val = SWBST_AUTO;
+		ret = pmic_reg_write(p, SWBST_CTRL, val);
+		if (ret) {
+			printf("Writing to SWBST_CTRL failed: %d\n", ret);
+			return ret;
+		}
+
+		return ret;
+	}
+
+	return -1;
+}
+
+static void clock_1GHz(void)
+{
+	int ret;
+	u32 ref_clk = MXC_HCLK;
+	/*
+	 * After increasing voltage to 1.25V, we can switch
+	 * CPU clock to 1GHz and DDR to 400MHz safely
+	 */
+	ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
+	if (ret)
+		printf("CPU:   Switch CPU clock to 1GHZ failed\n");
+
+	ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
+	ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
+	if (ret)
+		printf("CPU:   Switch DDR clock to 400MHz failed\n");
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_fec();
+	setup_iomux_lcd();
+
+	return 0;
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+	u32 cpurev;
+
+	cpurev = get_cpu_rev();
+	printf("CPU:   Freescale i.MX%x family rev%d.%d at %d MHz\n",
+		(cpurev & 0xFF000) >> 12,
+		(cpurev & 0x000F0) >> 4,
+		(cpurev & 0x0000F) >> 0,
+		mxc_get_clock(MXC_ARM_CLK) / 1000000);
+	printf("Reset cause: %s\n", get_reset_cause());
+	return 0;
+}
+#endif
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	mxc_set_sata_internal_clock();
+	setup_iomux_i2c();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	if (!power_init())
+		clock_1GHz();
+	print_cpuinfo();
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: MX53 LOCO\n");
+
+	return 0;
+}
diff --git a/qemu/roms/u-boot/board/freescale/mx53loco/mx53loco_video.c b/qemu/roms/u-boot/board/freescale/mx53loco/mx53loco_video.c
new file mode 100644
index 000000000..bc5e8a9d3
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mx53loco/mx53loco_video.c
@@ -0,0 +1,114 @@
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ * Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/list.h>
+#include <asm/gpio.h>
+#include <asm/arch/iomux-mx53.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+
+#define MX53LOCO_LCD_POWER		IMX_GPIO_NR(3, 24)
+
+static struct fb_videomode const claa_wvga = {
+	.name		= "CLAA07LC0ACW",
+	.refresh	= 57,
+	.xres		= 800,
+	.yres		= 480,
+	.pixclock	= 37037,
+	.left_margin	= 40,
+	.right_margin	= 60,
+	.upper_margin	= 10,
+	.lower_margin	= 10,
+	.hsync_len	= 20,
+	.vsync_len	= 10,
+	.sync		= 0,
+	.vmode		= FB_VMODE_NONINTERLACED
+};
+
+static struct fb_videomode const seiko_wvga = {
+	.name		= "Seiko-43WVF1G",
+	.refresh	= 60,
+	.xres		= 800,
+	.yres		= 480,
+	.pixclock	= 29851, /* picosecond (33.5 MHz) */
+	.left_margin	= 89,
+	.right_margin	= 164,
+	.upper_margin	= 23,
+	.lower_margin	= 10,
+	.hsync_len	= 10,
+	.vsync_len	= 10,
+	.sync		= 0,
+};
+
+void setup_iomux_lcd(void)
+{
+	static const iomux_v3_cfg_t lcd_pads[] = {
+		MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
+		MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
+		MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
+		MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
+		MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
+		MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
+		MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
+		MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
+		MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
+		MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
+		MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
+		MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
+		MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
+		MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
+		MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
+		MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
+		MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
+		MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
+		MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
+		MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
+		MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
+		MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
+		MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
+		MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
+		MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
+		MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
+		MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
+		MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
+	};
+
+	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+	/* Turn on GPIO backlight */
+	imx_iomux_v3_setup_pad(MX53_PAD_EIM_D24__GPIO3_24);
+	gpio_direction_output(MX53LOCO_LCD_POWER, 1);
+
+	/* Turn on display contrast */
+	imx_iomux_v3_setup_pad(MX53_PAD_GPIO_1__GPIO1_1);
+	gpio_direction_output(IMX_GPIO_NR(1, 1), 1);
+}
+
+int board_video_skip(void)
+{
+	int ret;
+	char const *e = getenv("panel");
+
+	if (e) {
+		if (strcmp(e, "seiko") == 0) {
+			ret = ipuv3_fb_init(&seiko_wvga, 0, IPU_PIX_FMT_RGB24);
+			if (ret)
+				printf("Seiko cannot be configured: %d\n", ret);
+			return ret;
+		}
+	}
+
+	/*
+	 * 'panel' env variable not found or has different value than 'seiko'
+	 *  Defaulting to claa lcd.
+	 */
+	ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565);
+	if (ret)
+		printf("CLAA cannot be configured: %d\n", ret);
+	return ret;
+}