Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

5 files changed, 589 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/freescale/mpc8641hpcn/Makefile b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/Makefile
new file mode 100644
index 000000000..86c70bcb9
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/Makefile
@@ -0,0 +1,10 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	+= mpc8641hpcn.o
+obj-y	+= law.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
diff --git a/qemu/roms/u-boot/board/freescale/mpc8641hpcn/README b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/README
new file mode 100644
index 000000000..d8fe0a4a1
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/README
@@ -0,0 +1,186 @@
+Freescale MPC8641HPCN board
+===========================
+
+Created 05/24/2006 Haiying Wang
+-------------------------------
+
+1. Building U-Boot
+------------------
+The 86xx HPCN code base is known to compile using:
+    Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3
+
+    $ make MPC8641HPCN_config
+    Configuring for MPC8641HPCN board...
+
+    $ make
+
+
+2. Switch and Jumper Setting
+----------------------------
+Jumpers:
+	J14 Pins 1-2 (near plcc32 socket)
+
+Switches:
+	SW1(1-5) = 01100	CONFIG_SYS_COREPLL	= 01000 :: CORE =   2:1
+						  01100 :: CORE = 2.5:1
+						  10000 :: CORE =   3:1
+						  11100 :: CORE = 3.5:1
+						  10100 :: CORE =   4:1
+						  01110 :: CORE = 4.5:1
+	SW1(6-8) = 001		CONFIG_SYS_SYSCLK	= 000	:: SYSCLK = 33MHz
+						  001	:: SYSCLK = 40MHz
+
+	SW2(1-4) = 1100		CONFIG_SYS_CCBPLL	= 0010	:: 2X
+						  0100	:: 4X
+						  0110	:: 6X
+						  1000	:: 8X
+						  1010	:: 10X
+						  1100	:: 12X
+						  1110	:: 14X
+						  0000	:: 16X
+	SW2(5-8) = 1110		CONFIG_SYS_BOOTLOC	= 1110	:: boot 16-bit localbus
+
+	SW3(1-7) = 0011000	CONFIG_SYS_VID		= 0011000 :: VCORE = 1.2V
+						  0100000 :: VCORE = 1.11V
+	SW3(8)	 = 0		VCC_PLAT	= 0	:: VCC_PLAT = 1.2V
+						  1	:: VCC_PLAT = 1.0V
+
+	SW4(1-2) = 11		CONFIG_SYS_HOSTMODE	= 11	:: both prots host/root
+	SW4(3-4) = 11		CONFIG_SYS_BOOTSEQ	= 11	:: no boot seq
+	SW4(5-8) = 0011		CONFIG_SYS_IOPORT	= 0011	:: both PEX
+
+	SW5(1)	 = 1		CONFIG_SYS_FLASHMAP	= 1	:: boot from flash
+						  0	:: boot from PromJet
+	SW5(2)	 = 1		CONFIG_SYS_FLASHBANK	= 1	:: swap upper/lower
+							 halves (virtual banks)
+						  0	:: normal
+	SW5(3)	 = 0		CONFIG_SYS_FLASHWP	= 0	:: not protected
+	SW5(4)	 = 0		CONFIG_SYS_PORTDIV	= 1	:: 2:1 for PD4
+							   1:1 for PD6
+	SW5(5-6) = 11		CONFIG_SYS_PIXISOPT	= 11	:: s/w determined
+	SW5(7-8) = 11		CONFIG_SYS_LADOPT	= 11	:: s/w determined
+
+	SW6(1)	 = 1		CONFIG_SYS_CPUBOOT	= 1	:: no boot holdoff
+	SW6(2)	 = 1		CONFIG_SYS_BOOTADDR	= 1	:: no traslation
+	SW6(3-5) = 000		CONFIG_SYS_REFCLKSEL	= 000	:: 100MHZ
+	SW6(6)	 = 1		CONFIG_SYS_SERROM_ADDR= 1	::
+	SW6(7)	 = 1		CONFIG_SYS_MEMDEBUG	= 1	::
+	SW6(8)	 = 1		CONFIG_SYS_DDRDEBUG	= 1	::
+
+	SW8(1)	 = 1		ACZ_SYNC	= 1	:: 48MHz on TP49
+	SW8(2)	 = 1		ACB_SYNC	= 1	:: THRMTRIP disabled
+	SW8(3)	 = 1		ACZ_SDOUT	= 1	:: p4 mode
+	SW8(4)	 = 1		ACB_SDOUT	= 1	:: PATA freq. = 133MHz
+	SW8(5)	 = 0		SUSLED		= 0	:: SouthBridge Mode
+	SW8(6)	 = 0		SPREAD		= 0	:: REFCLK SSCG Disabled
+	SW8(7)	 = 1		ACPWR		= 1	:: non-battery
+	SW8(8)	 = 0		CONFIG_SYS_IDWP	= 0	:: write enable
+
+
+3. Flash U-Boot
+---------------
+The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves.
+It is possible to use either half to boot using u-boot.  Switch 5 bit 2
+is used for this purpose.
+
+0xEF800000 to 0xEFBFFFFF - 4MB
+0xEFC00000 to 0xEFFFFFFF - 4MB
+When this bit is 0, U-Boot is at 0xEFF00000.
+When this bit is 1, U-Boot is at 0xEFB00000.
+
+Use the above mentioned flash commands to program the other half, and
+use switch 5, bit 2 to alternate between the halves.  Note: The booting
+version of U-Boot will always be at 0xEFF00000.
+
+To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF):
+
+	tftp 1000000 u-boot.bin
+	protect off all
+	erase eff00000 +$filesize
+	cp.b 1000000 eff00000 $filesize
+
+or use tftpflash command:
+	run tftpflash
+
+To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
+
+	tftp 1000000 u-boot.bin
+	erase efb00000 +$filesize
+	cp.b 1000000 efb00000 $filesize
+
+
+4. Memory Map
+-------------
+NOTE:  RIO and PCI are mutually exclusive, so they share an address
+
+For 32-bit u-boot, devices are mapped so that the virtual address ==
+the physical address, and the map looks liks this:
+
+	Memory Range			Device		Size
+	------------			------		----
+	0x0000_0000	0x7fff_ffff	DDR		2G
+	0x8000_0000	0x9fff_ffff	RIO MEM		512M
+	0x8000_0000	0x9fff_ffff	PCI1/PEX1 MEM	512M
+	0xa000_0000	0xbfff_ffff	PCI2/PEX2 MEM	512M
+	0xffe0_0000	0xffef_ffff	CCSR		1M
+	0xffdf_0000	0xffdf_7fff	PIXIS		8K
+	0xffdf_8000	0xffdf_ffff	CF		8K
+	0xf840_0000	0xf840_3fff	Stack space	32K
+	0xffc0_0000	0xffc0_ffff	PCI1/PEX1 IO	64K
+	0xffc1_0000	0xffc1_ffff	PCI2/PEX2 IO	64K
+	0xef80_0000	0xefff_ffff	Flash		8M
+
+For 36-bit-enabled u-boot, the virtual map is the same as for 32-bit.
+However, the physical map is altered to reside in 36-bit space, as follows.
+Addresses are no longer mapped with VA == PA.  All accesses from
+software use the VA; the PA is only used for setting up windows
+and mappings. Note that with the exception of PCI MEM and RIO, the low
+ 32 bits are the same as the VA above; only the top 4 bits vary:
+
+	Memory Range			Device		Size
+	------------			------		----
+	0x0_0000_0000	0x0_7fff_ffff	DDR		2G
+	0xc_0000_0000	0xc_1fff_ffff	RIO MEM		512M
+	0xc_0000_0000	0xc_1fff_ffff	PCI1/PEX1 MEM	512M
+	0xc_2000_0000	0xc_3fff_ffff	PCI2/PEX2 MEM	512M
+	0xf_ffe0_0000	0xf_ffef_ffff	CCSR		1M
+	0xf_ffdf_0000	0xf_ffdf_7fff	PIXIS		8K
+	0xf_ffdf_8000	0xf_ffdf_ffff	CF		8K
+	0x0_f840_0000	0xf_f840_3fff	Stack space	32K
+	0xf_ffc0_0000	0xf_ffc0_ffff	PCI1/PEX1 IO	64K
+	0xf_ffc1_0000	0xf_ffc1_ffff	PCI2/PEX2 IO	64K
+	0xf_ef80_0000	0xf_efff_ffff	Flash		8M
+
+5. pixis_reset command
+--------------------
+A new command, "pixis_reset", is introduced to reset mpc8641hpcn board
+using the FPGA sequencer.  When the board restarts, it has the option
+of using either the current or alternate flash bank as the boot
+image, with or without the watchdog timer enabled, and finally with
+or without frequency changes.
+
+Usage is;
+
+	pixis_reset
+	pixis_reset altbank
+	pixis_reset altbank wd
+	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+
+Examples;
+
+	/* reset to current bank, like "reset" command */
+	pixis_reset
+
+	/* reset board but use the to alternate flash bank */
+	pixis_reset altbank
+
+	/* reset board, use alternate flash bank with watchdog timer enabled*/
+	pixis_reset altbank wd
+
+	/* reset board to alternate bank with frequency changed.
+	 * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio
+	 */
+	pixis-reset altbank cf 40 2.5 10
+
+Valid clock choices are in the 8641 Reference Manuals.
diff --git a/qemu/roms/u-boot/board/freescale/mpc8641hpcn/ddr.c b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/ddr.c
new file mode 100644
index 000000000..7cd039565
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/ddr.c
@@ -0,0 +1,110 @@
+/*
+ * Copyright 2008,2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 clk_adjust;
+	u32 cpo;
+	u32 write_data_delay;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+const struct board_specific_parameters dimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| cpo|wrdata|2T
+	 * ranks| mhz|adjst|    | delay|
+	 */
+	{4,  333,    7,   7,     3},
+	{4,  549,    7,   9,     3},
+	{4,  650,    7,  10,     4},
+	{2,  333,    7,   7,     3},
+	{2,  549,    7,   9,     3},
+	{2,  650,    7,  10,     4},
+	{1,  333,    7,   7,     3},
+	{1,  549,    7,   9,     3},
+	{1,  650,    7,  10,     4},
+	{}
+};
+
+/*
+ * The two slots have slightly different timing. The center values are good
+ * for both slots. We use identical speed tables for them. In future use, if
+ * DIMMs have fewer center values that require two separated tables, copy the
+ * udimm0 table to udimm1 and make changes to clk_adjust and wrlvl_start.
+ */
+const struct board_specific_parameters *dimms[] = {
+	dimm0,
+	dimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+			dimm_params_t *pdimm,
+			unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	unsigned int i;
+	ulong ddr_freq;
+
+	if (ctrl_num > 1) {
+		printf("Wrong parameter for controller number %d", ctrl_num);
+		return;
+	}
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (pdimm[i].n_ranks)
+			break;
+	}
+	if (i >= CONFIG_DIMM_SLOTS_PER_CTLR)    /* no DIMM */
+		return;
+
+	pbsp = dimms[ctrl_num];
+
+	/* Get clk_adjust, cpo, write_data_delay, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm[i].n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->cpo_override = pbsp->cpo;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found "
+			"for data rate %lu MT/s!\n"
+			"Trying to use the highest speed (%u) parameters\n",
+			ddr_freq, pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->cpo_override = pbsp_highest->cpo;
+		popts->write_data_delay = pbsp_highest->write_data_delay;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+
+found:
+	/* 2T timing enable */
+	popts->twot_en = 1;
+}
diff --git a/qemu/roms/u-boot/board/freescale/mpc8641hpcn/law.c b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/law.c
new file mode 100644
index 000000000..6d25c76cc
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/law.c
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2008,2010-2011 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * if PCI (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT)
+ * 0x8000_0000     0x9fff_ffff     PCIE1 MEM                512M
+ * 0xa000_0000     0xbfff_ffff     PCIE2 MEM                512M
+ * else if RIO (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT)
+ * 0x8000_0000     0x9fff_ffff     RapidIO                 512M
+ * endif
+ * (prepend 0xf_0000_0000 if CONFIG_PHYS_64BIT)
+ * 0xffc0_0000     0xffc0_ffff     PCIE1 IO                 64K
+ * 0xffc1_0000     0xffc1_ffff     PCIE2 IO                 64K
+ * 0xffe0_0000     0xffef_ffff     CCSRBAR                 1M
+ * 0xffdf_0000     0xffe0_0000     PIXIS, CF               64K
+ * 0xef80_0000     0xefff_ffff     FLASH (boot bank)       8M
+ *
+ * Notes:
+ *    CCSRBAR doesn't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+struct law_entry law_table[] = {
+#if !defined(CONFIG_SPD_EEPROM)
+	SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR_1),
+#endif
+	SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/qemu/roms/u-boot/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/mpc8641hpcn.c
new file mode 100644
index 000000000..a58b5f9cd
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8641hpcn/mpc8641hpcn.c
@@ -0,0 +1,239 @@
+/*
+ * Copyright 2006, 2007, 2010-2011 Freescale Semiconductor.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_86xx.h>
+#include <asm/fsl_pci.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/fsl_serdes.h>
+#include <asm/io.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <netdev.h>
+
+phys_size_t fixed_sdram(void);
+
+int checkboard(void)
+{
+	u8 vboot;
+	u8 *pixis_base = (u8 *)PIXIS_BASE;
+
+	printf ("Board: MPC8641HPCN, Sys ID: 0x%02x, "
+		"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+		in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
+		in_8(pixis_base + PIXIS_PVER));
+
+	vboot = in_8(pixis_base + PIXIS_VBOOT);
+	if (vboot & PIXIS_VBOOT_FMAP)
+		printf ("vBank: %d\n", ((vboot & PIXIS_VBOOT_FBANK) >> 6));
+	else
+		puts ("Promjet\n");
+
+	return 0;
+}
+
+phys_size_t
+initdram(int board_type)
+{
+	phys_size_t dram_size = 0;
+
+#if defined(CONFIG_SPD_EEPROM)
+	dram_size = fsl_ddr_sdram();
+#else
+	dram_size = fixed_sdram();
+#endif
+
+	setup_ddr_bat(dram_size);
+
+	debug("    DDR: ");
+	return dram_size;
+}
+
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+phys_size_t
+fixed_sdram(void)
+{
+#if !defined(CONFIG_SYS_RAMBOOT)
+	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+	struct ccsr_ddr __iomem *ddr = &immap->im_ddr1;
+
+	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
+	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
+	ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
+	ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
+	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
+	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
+	ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
+	ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
+	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
+	ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
+	ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
+	ddr->sdram_ocd_cntl = CONFIG_SYS_DDR_OCD_CTRL;
+	ddr->sdram_ocd_status = CONFIG_SYS_DDR_OCD_STATUS;
+
+#if defined (CONFIG_DDR_ECC)
+	ddr->err_disable = 0x0000008D;
+	ddr->err_sbe = 0x00ff0000;
+#endif
+	asm("sync;isync");
+
+	udelay(500);
+
+#if defined (CONFIG_DDR_ECC)
+	/* Enable ECC checking */
+	ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
+#else
+	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
+	ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2;
+#endif
+	asm("sync; isync");
+
+	udelay(500);
+#endif
+	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+}
+#endif	/* !defined(CONFIG_SPD_EEPROM) */
+
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+
+#ifdef CONFIG_PCIE1
+		/*
+		 * Activate ULI1575 legacy chip by performing a fake
+		 * memory access.  Needed to make ULI RTC work.
+		 */
+		in_be32((unsigned *) ((char *)(CONFIG_SYS_PCIE1_MEM_VIRT
+				       + CONFIG_SYS_PCIE1_MEM_SIZE - 0x1000000)));
+#endif /* CONFIG_PCIE1 */
+}
+
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void
+ft_board_setup(void *blob, bd_t *bd)
+{
+	int off;
+	u64 *tmp;
+	u32 *addrcells;
+
+	ft_cpu_setup(blob, bd);
+
+	FT_FSL_PCI_SETUP;
+
+	/*
+	 * Warn if it looks like the device tree doesn't match u-boot.
+	 * This is just an estimation, based on the location of CCSR,
+	 * which is defined by the "reg" property in the soc node.
+	 */
+	off = fdt_path_offset(blob, "/soc8641");
+	addrcells = (u32 *)fdt_getprop(blob, 0, "#address-cells", NULL);
+	tmp = (u64 *)fdt_getprop(blob, off, "reg", NULL);
+
+	if (tmp) {
+		u64 addr;
+		if (addrcells && (*addrcells == 1))
+			addr = *(u32 *)tmp;
+		else
+			addr = *tmp;
+
+		if (addr != CONFIG_SYS_CCSRBAR_PHYS)
+			printf("WARNING: The CCSRBAR address in your .dts "
+			       "does not match the address of the CCSR "
+			       "in u-boot.  This means your .dts might "
+			       "be old.\n");
+	}
+}
+#endif
+
+
+/*
+ * get_board_sys_clk
+ *      Reads the FPGA on board for CONFIG_SYS_CLK_FREQ
+ */
+
+unsigned long
+get_board_sys_clk(ulong dummy)
+{
+	u8 i, go_bit, rd_clks;
+	ulong val = 0;
+	u8 *pixis_base = (u8 *)PIXIS_BASE;
+
+	go_bit = in_8(pixis_base + PIXIS_VCTL);
+	go_bit &= 0x01;
+
+	rd_clks = in_8(pixis_base + PIXIS_VCFGEN0);
+	rd_clks &= 0x1C;
+
+	/*
+	 * Only if both go bit and the SCLK bit in VCFGEN0 are set
+	 * should we be using the AUX register. Remember, we also set the
+	 * GO bit to boot from the alternate bank on the on-board flash
+	 */
+
+	if (go_bit) {
+		if (rd_clks == 0x1c)
+			i = in_8(pixis_base + PIXIS_AUX);
+		else
+			i = in_8(pixis_base + PIXIS_SPD);
+	} else {
+		i = in_8(pixis_base + PIXIS_SPD);
+	}
+
+	i &= 0x07;
+
+	switch (i) {
+	case 0:
+		val = 33000000;
+		break;
+	case 1:
+		val = 40000000;
+		break;
+	case 2:
+		val = 50000000;
+		break;
+	case 3:
+		val = 66000000;
+		break;
+	case 4:
+		val = 83000000;
+		break;
+	case 5:
+		val = 100000000;
+		break;
+	case 6:
+		val = 134000000;
+		break;
+	case 7:
+		val = 166000000;
+		break;
+	}
+
+	return val;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	/* Initialize TSECs */
+	cpu_eth_init(bis);
+	return pci_eth_init(bis);
+}
+
+void board_reset(void)
+{
+	u8 *pixis_base = (u8 *)PIXIS_BASE;
+
+	out_8(pixis_base + PIXIS_RST, 0);
+
+	while (1)
+		;
+}