Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

6 files changed, 702 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/freescale/mpc8572ds/Makefile b/qemu/roms/u-boot/board/freescale/mpc8572ds/Makefile
new file mode 100644
index 000000000..902c90016
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8572ds/Makefile
@@ -0,0 +1,12 @@
+#
+# Copyright 2007 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	+= mpc8572ds.o
+obj-y	+= ddr.o
+obj-y	+= law.o
+obj-y	+= tlb.o
diff --git a/qemu/roms/u-boot/board/freescale/mpc8572ds/README b/qemu/roms/u-boot/board/freescale/mpc8572ds/README
new file mode 100644
index 000000000..57fd2ad61
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8572ds/README
@@ -0,0 +1,166 @@
+Overview
+--------
+MPC8572DS is a high-performance computing, evaluation and development platform
+supporting the mpc8572 PowerTM processor.
+
+Building U-boot
+-----------
+	make MPC8572DS_config
+	make
+
+Flash Banks
+-----------
+MPC8572DS board has two flash banks. They are both present on boot, but their
+locations can be swapped using the dip-switch SW9[1:2].
+
+Booting is always from the boot bank at 0xec00_0000.
+
+
+Memory Map
+----------
+
+0xe800_0000 - 0xebff_ffff	Alternate bank		64MB
+0xec00_0000 - 0xefff_ffff	Boot bank		64MB
+
+0xebf8_0000 - 0xebff_ffff	Alternate u-boot address	512KB
+0xeff8_0000 - 0xefff_ffff	Boot u-boot address		512KB
+
+
+Flashing Images
+---------------
+
+To place a new u-boot image in the alternate flash bank and then reset with that
+ new image temporarily, use this:
+
+	tftp 1000000 u-boot.bin
+	erase ebf80000 ebffffff
+	cp.b 1000000 ebf80000 80000
+	pixis_reset altbank
+
+
+To program the image in the boot flash bank:
+
+	tftp 1000000 u-boot.bin
+	protect off all
+	erase eff80000 ffffffff
+	cp.b 1000000 eff80000 80000
+
+
+The pixis_reset command
+-----------------------
+The command - "pixis_reset", is introduced to reset mpc8572ds board
+using the FPGA sequencer.  When the board restarts, it has the option
+of using either the current or alternate flash bank as the boot
+image, with or without the watchdog timer enabled, and finally with
+or without frequency changes.
+
+Usage is;
+
+	pixis_reset
+	pixis_reset altbank
+	pixis_reset altbank wd
+	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+
+Examples:
+
+	/* reset to current bank, like "reset" command */
+	pixis_reset
+
+	/* reset board but use the to alternate flash bank */
+	pixis_reset altbank
+
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+	dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb
+
+Likely, that .dts file will come from here;
+
+	linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts
+
+
+Booting Linux
+-------------
+
+Place a linux uImage in the TFTP disk area.
+
+	tftp 1000000 uImage.8572
+	tftp c00000 mpc8572ds.dtb
+	bootm 1000000 - c00000
+
+
+Implementing AMP(Asymmetric MultiProcessing)
+-------------
+1. Build kernel image for core0:
+
+	a. $ make 85xx/mpc8572_ds_defconfig
+
+	b. $ make menuconfig
+	   - un-select "Processor support"->"Symetric multi-processing support"
+
+	c. $ make uImage
+
+	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
+
+2. Build kernel image for core1:
+
+	a. $ make 85xx/mpc8572_ds_defconfig
+
+	b. $ make menuconfig
+	   - Un-select "Processor support"->"Symetric multi-processing support"
+	   - Select "Advanced setup" -> " Prompt for advanced kernel
+	     configuration options"
+		- Select "Set physical address where the kernel is loaded" and
+		  set it to 0x20000000, assuming core1 will start from 512MB.
+		- Select "Set custom page offset address"
+		- Select "Set custom kernel base address"
+		- Select "Set maximum low memory"
+	   - "Exit" and save the selection.
+
+	c. $ make uImage
+
+	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
+
+3. Create dtb for core0:
+
+	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
+
+4. Create dtb for core1:
+
+	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
+
+5. Bring up two cores separately:
+
+	a. Power on the board, under u-boot prompt:
+		=> setenv <serverip>
+		=> setenv <ipaddr>
+		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
+	b. Bring up core1's kernel first:
+		=> setenv bootm_low 0x20000000
+		=> setenv bootm_size 0x10000000
+		=> tftp 21000000 8572/uImage.core1
+		=> tftp 22000000 8572/ramdiskfile
+		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
+		=> interrupts off
+		=> bootm start 21000000 22000000 20c00000
+		=> bootm loados
+		=> bootm ramdisk
+		=> bootm fdt
+		=> fdt boardsetup
+		=> fdt chosen $initrd_start $initrd_end
+		=> bootm prep
+		=> cpu 1 release $bootm_low - $fdtaddr -
+	c. Bring up core0's kernel(on the same u-boot console):
+		=> setenv bootm_low 0
+		=> setenv bootm_size 0x20000000
+		=> tftp 1000000 8572/uImage.core0
+		=> tftp 2000000 8572/ramdiskfile
+		=> tftp c00000 8572/mpc8572ds_core0.dtb
+		=> bootm 1000000 2000000 c00000
+
+Please note only core0 will run u-boot, core1 starts kernel directly after
+"cpu release" command is issued.
diff --git a/qemu/roms/u-boot/board/freescale/mpc8572ds/ddr.c b/qemu/roms/u-boot/board/freescale/mpc8572ds/ddr.c
new file mode 100644
index 000000000..2bfc1a170
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8572ds/ddr.c
@@ -0,0 +1,169 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+struct board_specific_parameters {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 clk_adjust;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2t;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ *
+ * For DDR2 DIMM, all combinations of clk_adjust and write_data_delay have been
+ * tested. For RDIMM, clk_adjust = 4 and write_data_delay = 3 is optimized for
+ * all clocks from 400MT/s to 800MT/s, verified with Kingston KVR800D2D8P6/2G.
+ * For UDIMM, clk_adjust = 8 and write_delay = 5 is optimized for all clocks
+ * from 400MT/s to 800MT/s, verified with Micron MT18HTF25672AY-800E1.
+ *
+ * CPO value doesn't matter if workaround for errata 111 and 134 enabled.
+ */
+static const struct board_specific_parameters udimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| cpo|wrdata|2T
+	 * ranks| mhz|adjst|    | delay|
+	 */
+	{2,  333,    8,   7,    5,  0},
+	{2,  400,    8,   9,    5,  0},
+	{2,  549,    8,  11,    5,  0},
+	{2,  680,    8,  10,    5,  0},
+	{2,  850,    8,  12,    5,  1},
+	{1,  333,    6,   7,    3,  0},
+	{1,  400,    6,   9,    3,  0},
+	{1,  549,    6,  11,    3,  0},
+	{1,  680,    1,  10,    5,  0},
+	{1,  850,    1,  12,    5,  0},
+	{}
+};
+
+static const struct board_specific_parameters udimm1[] = {
+	/*
+	 * memory controller 1
+	 *   num|  hi|  clk| cpo|wrdata|2T
+	 * ranks| mhz|adjst|    | delay|
+	 */
+	{2,  333,    8,  7,    5,  0},
+	{2,  400,    8,  9,    5,  0},
+	{2,  549,    8, 11,    5,  0},
+	{2,  680,    8, 11,    5,  0},
+	{2,  850,    8, 13,    5,  1},
+	{1,  333,    6,  7,    3,  0},
+	{1,  400,    6,  9,    3,  0},
+	{1,  549,    6, 11,    3,  0},
+	{1,  680,    1, 11,    6,  0},
+	{1,  850,    1, 13,    6,  0},
+	{}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+	udimm0,
+	udimm1,
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| cpo|wrdata|2T
+	 * ranks| mhz|adjst|    | delay|
+	 */
+	{2,  333,    4,   7,    3,  0},
+	{2,  400,    4,   9,    3,  0},
+	{2,  549,    4,  11,    3,  0},
+	{2,  680,    4,  10,    3,  0},
+	{2,  850,    4,  12,    3,  1},
+	{}
+};
+
+static const struct board_specific_parameters rdimm1[] = {
+	/*
+	 * memory controller 1
+	 *   num|  hi|  clk| cpo|wrdata|2T
+	 * ranks| mhz|adjst|    | delay|
+	 */
+	{2,  333,     4,  7,    3,  0},
+	{2,  400,     4,  9,    3,  0},
+	{2,  549,     4, 11,    3,  0},
+	{2,  680,     4, 11,    3,  0},
+	{2,  850,     4, 13,    3,  1},
+	{}
+};
+
+static const struct board_specific_parameters *rdimms[] = {
+	rdimm0,
+	rdimm1,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num > 1) {
+		printf("Wrong parameter for controller number %d", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	if (popts->registered_dimm_en)
+		pbsp = rdimms[ctrl_num];
+	else
+		pbsp = udimms[ctrl_num];
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->cpo_override = pbsp->cpo;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				popts->twot_en = pbsp->force_2t;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found "
+			"for data rate %lu MT/s!\n"
+			"Trying to use the highest speed (%u) parameters\n",
+			ddr_freq, pbsp_highest->datarate_mhz_high);
+		popts->clk_adjust = pbsp->clk_adjust;
+		popts->cpo_override = pbsp->cpo;
+		popts->write_data_delay = pbsp->write_data_delay;
+		popts->twot_en = pbsp->force_2t;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+
+found:
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
diff --git a/qemu/roms/u-boot/board/freescale/mpc8572ds/law.c b/qemu/roms/u-boot/board/freescale/mpc8572ds/law.c
new file mode 100644
index 000000000..ab44add7b
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8572ds/law.c
@@ -0,0 +1,20 @@
+/*
+ * Copyright 2008, 2010 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+	SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/qemu/roms/u-boot/board/freescale/mpc8572ds/mpc8572ds.c b/qemu/roms/u-boot/board/freescale/mpc8572ds/mpc8572ds.c
new file mode 100644
index 000000000..56863222c
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8572ds/mpc8572ds.c
@@ -0,0 +1,247 @@
+/*
+ * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/io.h>
+#include <asm/fsl_serdes.h>
+#include <miiphy.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <tsec.h>
+#include <fsl_mdio.h>
+#include <netdev.h>
+
+#include "../common/sgmii_riser.h"
+
+int checkboard (void)
+{
+	u8 vboot;
+	u8 *pixis_base = (u8 *)PIXIS_BASE;
+
+	printf("Board: MPC8572DS Sys ID: 0x%02x, "
+		"Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+		in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
+		in_8(pixis_base + PIXIS_PVER));
+
+	vboot = in_8(pixis_base + PIXIS_VBOOT);
+	switch ((vboot & PIXIS_VBOOT_LBMAP) >> 6) {
+		case PIXIS_VBOOT_LBMAP_NOR0:
+			puts ("vBank: 0\n");
+			break;
+		case PIXIS_VBOOT_LBMAP_PJET:
+			puts ("Promjet\n");
+			break;
+		case PIXIS_VBOOT_LBMAP_NAND:
+			puts ("NAND\n");
+			break;
+		case PIXIS_VBOOT_LBMAP_NOR1:
+			puts ("vBank: 1\n");
+			break;
+	}
+
+	return 0;
+}
+
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+
+phys_size_t fixed_sdram (void)
+{
+	volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
+	struct ccsr_ddr __iomem *ddr = &immap->im_ddr;
+	uint d_init;
+
+	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
+	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
+
+	ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
+	ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
+	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
+	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
+	ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
+	ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
+	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
+	ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
+	ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
+	ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2;
+
+#if defined (CONFIG_DDR_ECC)
+	ddr->err_int_en = CONFIG_SYS_DDR_ERR_INT_EN;
+	ddr->err_disable = CONFIG_SYS_DDR_ERR_DIS;
+	ddr->err_sbe = CONFIG_SYS_DDR_SBE;
+#endif
+	asm("sync;isync");
+
+	udelay(500);
+
+	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
+
+#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+	d_init = 1;
+	debug("DDR - 1st controller: memory initializing\n");
+	/*
+	 * Poll until memory is initialized.
+	 * 512 Meg at 400 might hit this 200 times or so.
+	 */
+	while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
+		udelay(1000);
+	}
+	debug("DDR: memory initialized\n\n");
+	asm("sync; isync");
+	udelay(500);
+#endif
+
+	return 512 * 1024 * 1024;
+}
+
+#endif
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+	struct pci_controller *hose;
+
+	fsl_pcie_init_board(0);
+
+	hose = find_hose_by_cfg_addr((void *)(CONFIG_SYS_PCIE3_ADDR));
+
+	if (hose) {
+		u32 temp32;
+		u8 uli_busno = hose->first_busno + 2;
+
+		/*
+		 * Activate ULI1575 legacy chip by performing a fake
+		 * memory access.  Needed to make ULI RTC work.
+		 * Device 1d has the first on-board memory BAR.
+		 */
+		pci_hose_read_config_dword(hose, PCI_BDF(uli_busno, 0x1d, 0),
+				PCI_BASE_ADDRESS_1, &temp32);
+
+		if (temp32 >= CONFIG_SYS_PCIE3_MEM_BUS) {
+			void *p = pci_mem_to_virt(PCI_BDF(uli_busno, 0x1d, 0),
+					temp32, 4, 0);
+			debug(" uli1572 read to %p\n", p);
+			in_be32(p);
+		}
+	}
+}
+#endif
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,	/* tlb, epn, rpn */
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,	/* perms, wimge */
+			0, flash_esel, BOOKE_PAGESZ_256M, 1);	/* ts, esel, tsize, iprot */
+
+	return 0;
+}
+
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+	struct fsl_pq_mdio_info mdio_info;
+	struct tsec_info_struct tsec_info[4];
+	int num = 0;
+
+#ifdef CONFIG_TSEC1
+	SET_STD_TSEC_INFO(tsec_info[num], 1);
+	if (is_serdes_configured(SGMII_TSEC1)) {
+		puts("eTSEC1 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+#ifdef CONFIG_TSEC2
+	SET_STD_TSEC_INFO(tsec_info[num], 2);
+	if (is_serdes_configured(SGMII_TSEC2)) {
+		puts("eTSEC2 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+#ifdef CONFIG_TSEC3
+	SET_STD_TSEC_INFO(tsec_info[num], 3);
+	if (is_serdes_configured(SGMII_TSEC3)) {
+		puts("eTSEC3 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+#ifdef CONFIG_TSEC4
+	SET_STD_TSEC_INFO(tsec_info[num], 4);
+	if (is_serdes_configured(SGMII_TSEC4)) {
+		puts("eTSEC4 is in sgmii mode.\n");
+		tsec_info[num].flags |= TSEC_SGMII;
+	}
+	num++;
+#endif
+
+	if (!num) {
+		printf("No TSECs initialized\n");
+
+		return 0;
+	}
+
+#ifdef CONFIG_FSL_SGMII_RISER
+	fsl_sgmii_riser_init(tsec_info, num);
+#endif
+
+	mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+	mdio_info.name = DEFAULT_MII_NAME;
+	fsl_pq_mdio_init(bis, &mdio_info);
+
+	tsec_eth_init(bis, tsec_info, num);
+
+	return pci_eth_init(bis);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+	FT_FSL_PCI_SETUP;
+
+#ifdef CONFIG_FSL_SGMII_RISER
+	fsl_sgmii_riser_fdt_fixup(blob);
+#endif
+}
+#endif
diff --git a/qemu/roms/u-boot/board/freescale/mpc8572ds/tlb.c b/qemu/roms/u-boot/board/freescale/mpc8572ds/tlb.c
new file mode 100644
index 000000000..577878cf7
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/mpc8572ds/tlb.c
@@ -0,0 +1,88 @@
+/*
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_1M, 1),
+
+	/* W**G* - Flash/promjet, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+#ifndef CONFIG_NAND_SPL
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000, CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000, CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 5, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_256K, 1),
+#endif
+
+	/* *I*G - NAND */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 7, BOOKE_PAGESZ_1M, 1),
+
+	SET_TLB_ENTRY(1, PIXIS_BASE, PIXIS_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 8, BOOKE_PAGESZ_4K, 1),
+
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR)
+	/* *I*G - L2SRAM */
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR,
+			CONFIG_SYS_INIT_L2_ADDR_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 9, BOOKE_PAGESZ_256K, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+			CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, 10, BOOKE_PAGESZ_256K, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);