Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

1 files changed, 0 insertions, 432 deletions

diff --git a/qemu/roms/u-boot/board/cm5200/cmd_cm5200.c b/qemu/roms/u-boot/board/cm5200/cmd_cm5200.c
deleted file mode 100644
index 9c40ad7b2..000000000
--- a/qemu/roms/u-boot/board/cm5200/cmd_cm5200.c
+++ /dev/null
@@ -1,432 +0,0 @@
-/*
- * (C) Copyright 2007 Markus Kappeler <markus.kappeler@objectxp.com>
- *
- * Adapted for U-Boot 1.2 by Piotr Kruszynski <ppk@semihalf.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <i2c.h>
-#include <usb.h>
-
-#ifdef CONFIG_CMD_BSP
-
-static int do_i2c_test(char * const argv[])
-{
-	unsigned char temp, temp1;
-
-	printf("Starting I2C Test\n"
-		"Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n"
-		"Please press any key to start\n\n");
-	getc();
-
-	temp = 0xf0; /* set io 0-4 as output */
-	i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1);
-
-	printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n"
-		"Press any key to stop\n\n");
-
-	while (!tstc()) {
-		i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1);
-		temp1 = (temp >> 4) & 0x03;
-		temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */
-		temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */
-		temp = temp1;
-		i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1);
-	}
-	getc();
-
-	return 0;
-}
-
-static int do_usb_test(char * const argv[])
-{
-	int i;
-	static int usb_stor_curr_dev = -1; /* current device */
-
-	printf("Starting USB Test\n"
-		"Please insert USB Memmory Stick\n\n"
-		"Please press any key to start\n\n");
-	getc();
-
-	usb_stop();
-	printf("(Re)start USB...\n");
-	i = usb_init();
-#ifdef CONFIG_USB_STORAGE
-		/* try to recognize storage devices immediately */
-		if (i >= 0)
-			usb_stor_curr_dev = usb_stor_scan(1);
-#endif /* CONFIG_USB_STORAGE */
-	if (usb_stor_curr_dev >= 0)
-		printf("Found USB Storage Dev continue with Test...\n");
-	else {
-		printf("No USB Storage Device detected.. Stop Test\n");
-		return 1;
-	}
-
-	usb_stor_info();
-
-	printf("stopping USB..\n");
-	usb_stop();
-
-	return 0;
-}
-
-static int do_led_test(char * const argv[])
-{
-	int i = 0;
-	struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
-
-	printf("Starting LED Test\n"
-		"Please set Switch S500 all off\n\n"
-		"Please press any key to start\n\n");
-	getc();
-
-	/* configure timer 2-3 for simple GPIO output High */
-	gpt->gpt2.emsr |= 0x00000034;
-	gpt->gpt3.emsr |= 0x00000034;
-
-	(*(vu_long *)MPC5XXX_WU_GPIO_ENABLE) |= 0x80000000;
-	(*(vu_long *)MPC5XXX_WU_GPIO_DIR) |= 0x80000000;
-	printf("Please press any key to stop\n\n");
-	while (!tstc()) {
-		if (i == 1) {
-			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) |= 0x80000000;
-			gpt->gpt2.emsr &= ~0x00000010;
-			gpt->gpt3.emsr &= ~0x00000010;
-		} else if (i == 2) {
-			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) &= ~0x80000000;
-			gpt->gpt2.emsr &= ~0x00000010;
-			gpt->gpt3.emsr |= 0x00000010;
-		} else if (i >= 3) {
-			(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) &= ~0x80000000;
-			gpt->gpt3.emsr &= ~0x00000010;
-			gpt->gpt2.emsr |= 0x00000010;
-			i = 0;
-		}
-		i++;
-		udelay(200000);
-	}
-	getc();
-
-	(*(vu_long *)MPC5XXX_WU_GPIO_DATA_O) |= 0x80000000;
-	gpt->gpt2.emsr |= 0x00000010;
-	gpt->gpt3.emsr |= 0x00000010;
-
-	return 0;
-}
-
-static int do_rs232_test(char * const argv[])
-{
-	int error_status = 0;
-	struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
-	struct mpc5xxx_psc *psc1 = (struct mpc5xxx_psc *)MPC5XXX_PSC1;
-
-	/* Configure PSC 2-3-6 as GPIO */
-	gpio->port_config &= 0xFF0FF80F;
-
-	switch (simple_strtoul(argv[2], NULL, 10)) {
-	case 1:
-		/* check RTS <-> CTS loop */
-		/* set rts to 0 */
-		printf("Uart 1 test: RX TX tested by using U-Boot\n"
-			"Please connect RTS with CTS on Uart1 plug\n\n"
-			"Press any key to start\n\n");
-		getc();
-
-		psc1->op1 |= 0x01;
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		/* check status at cts */
-		if ((psc1->ip & 0x01) != 0) {
-			error_status = 3;
-			printf("%s: failure at rs232_1, cts status is %d "
-				"(should be 0)\n",
-				__FUNCTION__, (psc1->ip & 0x01));
-		}
-
-		/* set rts to 1 */
-		psc1->op0 |= 0x01;
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		/* check status at cts */
-		if ((psc1->ip & 0x01) != 1) {
-			error_status = 3;
-			printf("%s: failure at rs232_1, cts status is %d "
-				"(should be 1)\n",
-				__FUNCTION__, (psc1->ip & 0x01));
-		}
-		break;
-	case 2:
-		/* set PSC2_0, PSC2_2 as output and PSC2_1, PSC2_3 as input */
-		printf("Uart 2 test: Please use RS232 Loopback plug on UART2\n"
-			"\nPress any key to start\n\n");
-		getc();
-
-		gpio->simple_gpioe &= ~(0x000000F0);
-		gpio->simple_gpioe |= 0x000000F0;
-		gpio->simple_ddr &= ~(0x000000F0);
-		gpio->simple_ddr |= 0x00000050;
-
-		/* check TXD <-> RXD loop */
-		/* set TXD to 1 */
-		gpio->simple_dvo |= (1 << 4);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000020) != 0x00000020) {
-			error_status = 2;
-			printf("%s: failure at rs232_2, rxd status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000020) >> 5);
-		}
-
-		/* set TXD to 0 */
-		gpio->simple_dvo &= ~(1 << 4);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000020) != 0x00000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_2, rxd status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000020) >> 5);
-		}
-
-		/* check RTS <-> CTS loop */
-		/* set RTS to 1 */
-		gpio->simple_dvo |= (1 << 6);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000080) != 0x00000080) {
-			error_status = 3;
-			printf("%s: failure at rs232_2, cts status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000080) >> 7);
-		}
-
-		/* set RTS to 0 */
-		gpio->simple_dvo &= ~(1 << 6);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000080) != 0x00000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_2, cts status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000080) >> 7);
-		}
-		break;
-	case 3:
-		/* set PSC3_0, PSC3_2 as output and PSC3_1, PSC3_3 as input */
-		printf("Uart 3 test: Please use RS232 Loopback plug on UART2\n"
-			"\nPress any key to start\n\n");
-		getc();
-
-		gpio->simple_gpioe &= ~(0x00000F00);
-		gpio->simple_gpioe |= 0x00000F00;
-
-		gpio->simple_ddr &= ~(0x00000F00);
-		gpio->simple_ddr |= 0x00000500;
-
-		/* check TXD <-> RXD loop */
-		/* set TXD to 1 */
-		gpio->simple_dvo |= (1 << 8);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000200) != 0x00000200) {
-			error_status = 2;
-			printf("%s: failure at rs232_3, rxd status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000200) >> 9);
-		}
-
-		/* set TXD to 0 */
-		gpio->simple_dvo &= ~(1 << 8);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000200) != 0x00000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_3, rxd status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000200) >> 9);
-		}
-
-		/* check RTS <-> CTS loop */
-		/* set RTS to 1 */
-		gpio->simple_dvo |= (1 << 10);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000800) != 0x00000800) {
-			error_status = 3;
-			printf("%s: failure at rs232_3, cts status is %d "
-				"(should be 1)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000800) >> 11);
-		}
-
-		/* set RTS to 0 */
-		gpio->simple_dvo &= ~(1 << 10);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if ((gpio->simple_ival & 0x00000800) != 0x00000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_3, cts status is %d "
-				"(should be 0)\n", __FUNCTION__,
-				(gpio->simple_ival & 0x00000800) >> 11);
-		}
-		break;
-	case 4:
-		/* set PSC6_2, PSC6_3 as output and PSC6_0, PSC6_1 as input */
-		printf("Uart 4 test: Please use RS232 Loopback plug on UART2\n"
-			"\nPress any key to start\n\n");
-		getc();
-
-		gpio->simple_gpioe &= ~(0xF0000000);
-		gpio->simple_gpioe |= 0x30000000;
-
-		gpio->simple_ddr &= ~(0xf0000000);
-		gpio->simple_ddr |= 0x30000000;
-
-		(*(vu_long *)MPC5XXX_WU_GPIO_ENABLE) |= 0x30000000;
-		(*(vu_long *)MPC5XXX_WU_GPIO_DIR) &= ~(0x30000000);
-
-		/* check TXD <-> RXD loop */
-		/* set TXD to 1 */
-		gpio->simple_dvo |= (1 << 28);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x10000000) !=
-				0x10000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_4, rxd status is %lu "
-				"(should be 1)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x10000000) >> 28);
-		}
-
-		/* set TXD to 0 */
-		gpio->simple_dvo &= ~(1 << 28);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x10000000) !=
-				0x00000000) {
-			error_status = 2;
-			printf("%s: failure at rs232_4, rxd status is %lu "
-				"(should be 0)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x10000000) >> 28);
-		}
-
-		/* check RTS <-> CTS loop */
-		/* set RTS to 1 */
-		gpio->simple_dvo |= (1 << 29);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x20000000) !=
-				0x20000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_4, cts status is %lu "
-				"(should be 1)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x20000000) >> 29);
-		}
-
-		/* set RTS to 0 */
-		gpio->simple_dvo &= ~(1 << 29);
-
-		/* wait some time before requesting status */
-		udelay(10);
-
-		if (((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) & 0x20000000) !=
-				0x00000000) {
-			error_status = 3;
-			printf("%s: failure at rs232_4, cts status is %lu "
-				"(should be 0)\n", __FUNCTION__,
-				((*(vu_long *)MPC5XXX_WU_GPIO_DATA_I) &
-					0x20000000) >> 29);
-		}
-		break;
-	default:
-		printf("%s: invalid rs232 number %s\n", __FUNCTION__, argv[2]);
-		error_status = 1;
-		break;
-	}
-	gpio->port_config |= (CONFIG_SYS_GPS_PORT_CONFIG & 0xFF0FF80F);
-
-	return error_status;
-}
-
-static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	int rcode = -1;
-
-	switch (argc) {
-	case 2:
-		if (strncmp(argv[1], "i2c", 3) == 0)
-			rcode = do_i2c_test(argv);
-		else if (strncmp(argv[1], "led", 3) == 0)
-			rcode = do_led_test(argv);
-		else if (strncmp(argv[1], "usb", 3) == 0)
-			rcode = do_usb_test(argv);
-		break;
-	case 3:
-		if (strncmp(argv[1], "rs232", 3) == 0)
-			rcode = do_rs232_test(argv);
-		break;
-	}
-
-	switch (rcode) {
-	case -1:
-		printf("Usage:\n"
-			"fkt { i2c | led | usb }\n"
-			"fkt rs232 number\n");
-		rcode = 1;
-		break;
-	case 0:
-		printf("Test passed\n");
-		break;
-	default:
-		printf("Test failed with code: %d\n", rcode);
-	}
-
-	return rcode;
-}
-
-U_BOOT_CMD(
-	fkt,	4,	1,	cmd_fkt,
-	"Function test routines",
-	"i2c\n"
-	"     - Test I2C communication\n"
-	"fkt led\n"
-	"     - Test LEDs\n"
-	"fkt rs232 number\n"
-	"     - Test RS232 (loopback plug(s) for RS232 required)\n"
-	"fkt usb\n"
-	"     - Test USB communication"
-);
-#endif /* CONFIG_CMD_BSP */