Adding qemu as a submodule of KVMFORNFV

This Patch includes the changes to add qemu as a submodule to
kvmfornfv repo and make use of the updated latest qemu for the
execution of all testcase
Change-Id: I1280af507a857675c7f81d30c95255635667bdd7
Signed-off-by:RajithaY<rajithax.yerrumsetty@intel.com>

5 files changed, 0 insertions, 605 deletions

diff --git a/qemu/roms/u-boot/board/a3m071/Makefile b/qemu/roms/u-boot/board/a3m071/Makefile
deleted file mode 100644
index 4e31e3393..000000000
--- a/qemu/roms/u-boot/board/a3m071/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= a3m071.o
diff --git a/qemu/roms/u-boot/board/a3m071/README b/qemu/roms/u-boot/board/a3m071/README
deleted file mode 100644
index 112c47b60..000000000
--- a/qemu/roms/u-boot/board/a3m071/README
+++ /dev/null
@@ -1,80 +0,0 @@
-------------------------------------------------------------------------
-A3M071 board support
-------------------------------------------------------------------------
-
-
-SPL NOR flash support:
-----------------------
-To boot fast into the OS (Linux), this board port integrates the SPL
-framework. This means, that a special, stripped-down version of
-U-Boot runs in the beginning. In the case of the A3M071 board, this
-SPL U-Boot version is less than 16 KiB big. This SPL U-Boot can either
-boot the OS (Linux) or a "real", full-blown U-Boot. This detection
-on whether to boot Linux or U-Boot is done by using the "boot_os"
-environment variable. If "boot_os" is set to "yes", Linux will be
-loaded and booted from the SPL U-Boot version. Otherwise, the
-full-blown U-Boot version will be loaded and run.
-
-Enabling Linux booting:
------------------------
-From U-Boot:
-=> setenv boot_os yes
-=> saveenv
-
-From Linux:
-$ fw_setenv boot_os yes
-
-Enabling U-Boot booting:
-------------------------
-From U-Boot:
-=> setenv boot_os no
-=> saveenv
-
-From Linux:
-$ fw_setenv boot_os no
-
-
-Preparing Linux image(s) for booting from SPL U-Boot:
------------------------------------------------------
-To boot the Linux kernel from the SPL, the DT blob (fdt) needs to get
-prepard/patched first. U-Boot usually inserts some dynamic values into
-the DT binary (blob), e.g. autodetected memory size, MAC addresses,
-clocks speeds etc. To generate this patched DT blob, you can use
-the following command:
-
-1. Load fdt blob to SDRAM:
-=> tftp 1800000 a3m071/a3m071.dtb
-
-2. Set bootargs as desired for Linux booting (e.g. flash_mtd):
-=> run mtdargs addip2 addtty
-
-3. Use "fdt" commands to patch the DT blob:
-=> fdt addr 1800000
-=> fdt boardsetup
-=> fdt chosen
-
-4. Display patched DT blob (optional):
-=> fdt print
-
-5. Save fdt to NOR flash:
-=> erase fc180000 fc07ffff
-=> cp.b 1800000 fc180000 10000
-
-All this can be integrated into an environment command:
-=> setenv upd_fdt 'tftp 1800000 a3m071/a3m071.dtb;run mtdargs addip addtty; \
-	fdt addr 1800000;fdt boardsetup;fdt chosen;erase fc180000 fc07ffff; \
-	cp.b 1800000 fc180000 10000'
-=> saveenv
-
-After this, only "run upd_fdt" needs to get called to load, patch
-and save the DT blob into NOR flash.
-
-Additionally, the Linux kernel image has to be saved uncompressed in
-its uImage file (and not gzip compressed). This can be done with this
-command:
-
-$ mkimage -A ppc -O linux -T kernel -C none -a 0 -e 0 \
-	-n "Linux Kernel Image" -d vmlinux.bin uImage.uncompressed
-
-------------------------------------------------------------------------
-Stefan Roese, 2012-08-23
diff --git a/qemu/roms/u-boot/board/a3m071/a3m071.c b/qemu/roms/u-boot/board/a3m071/a3m071.c
deleted file mode 100644
index b96ba811f..000000000
--- a/qemu/roms/u-boot/board/a3m071/a3m071.c
+++ /dev/null
@@ -1,475 +0,0 @@
-/*
- * (C) Copyright 2003-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * (C) Copyright 2006
- * MicroSys GmbH
- *
- * Copyright 2012-2013 Stefan Roese <sr@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <miiphy.h>
-#include <linux/compiler.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-
-#ifdef CONFIG_A4M2K
-#include "is46r16320d.h"
-#else
-#include "mt46v16m16-75.h"
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if !defined(CONFIG_SYS_RAMBOOT) && \
-	(defined(CONFIG_SPL) && defined(CONFIG_SPL_BUILD))
-static void sdram_start(int hi_addr)
-{
-	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-	long control = SDRAM_CONTROL | hi_addr_bit;
-
-	/* unlock mode register */
-	out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000000);
-
-	/* precharge all banks */
-	out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000002);
-
-#ifdef SDRAM_DDR
-	/* set mode register: extended mode */
-	out_be32((void *)MPC5XXX_SDRAM_MODE, SDRAM_EMODE);
-
-	/* set mode register: reset DLL */
-	out_be32((void *)MPC5XXX_SDRAM_MODE, SDRAM_MODE | 0x04000000);
-#endif
-
-	/* precharge all banks */
-	out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000002);
-
-	/* auto refresh */
-	out_be32((void *)MPC5XXX_SDRAM_CTRL, control | 0x80000004);
-
-	/* set mode register */
-	out_be32((void *)MPC5XXX_SDRAM_MODE, SDRAM_MODE);
-
-	/* normal operation */
-	out_be32((void *)MPC5XXX_SDRAM_CTRL, control);
-
-	/*
-	 * Wait a short while for the DLL to lock before accessing
-	 * the SDRAM
-	 */
-	udelay(100);
-}
-#endif
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- * use of CONFIG_SYS_SDRAM_BASE. The code does not work if
- * CONFIG_SYS_SDRAM_BASE is something else than 0x00000000.
- */
-phys_size_t initdram(int board_type)
-{
-	ulong dramsize = 0;
-	ulong dramsize2 = 0;
-	uint svr, pvr;
-#if !defined(CONFIG_SYS_RAMBOOT) && \
-	(defined(CONFIG_SPL) && defined(CONFIG_SPL_BUILD))
-	ulong test1, test2;
-
-	/* setup SDRAM chip selects */
-	out_be32((void *)MPC5XXX_SDRAM_CS0CFG, 0x0000001e);	/* 2GB at 0x0 */
-	out_be32((void *)MPC5XXX_SDRAM_CS1CFG, 0x80000000);	/* disabled */
-
-	/* setup config registers */
-	out_be32((void *)MPC5XXX_SDRAM_CONFIG1, SDRAM_CONFIG1);
-	out_be32((void *)MPC5XXX_SDRAM_CONFIG2, SDRAM_CONFIG2);
-
-#ifdef SDRAM_DDR
-	/* set tap delay */
-	out_be32((void *)MPC5XXX_CDM_PORCFG, SDRAM_TAPDELAY);
-#endif
-
-	/* find RAM size using SDRAM CS0 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize = test1;
-	} else {
-		dramsize = test2;
-	}
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize < (1 << 20))
-		dramsize = 0;
-
-	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0) {
-		out_be32((void *)MPC5XXX_SDRAM_CS0CFG,
-			 0x13 + __builtin_ffs(dramsize >> 20) - 1);
-	} else {
-		out_be32((void *)MPC5XXX_SDRAM_CS0CFG, 0);	/* disabled */
-	}
-#else /* CONFIG_SYS_RAMBOOT */
-
-	/* retrieve size of memory connected to SDRAM CS0 */
-	dramsize = in_be32((void *)MPC5XXX_SDRAM_CS0CFG) & 0xFF;
-	if (dramsize >= 0x13)
-		dramsize = (1 << (dramsize - 0x13)) << 20;
-	else
-		dramsize = 0;
-
-	/* retrieve size of memory connected to SDRAM CS1 */
-	dramsize2 = in_be32((void *)MPC5XXX_SDRAM_CS1CFG) & 0xFF;
-	if (dramsize2 >= 0x13)
-		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
-	else
-		dramsize2 = 0;
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
-	/*
-	 * On MPC5200B we need to set the special configuration delay in the
-	 * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
-	 * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
-	 *
-	 * "The SDelay should be written to a value of 0x00000004. It is
-	 * required to account for changes caused by normal wafer processing
-	 * parameters."
-	 */
-	svr = get_svr();
-	pvr = get_pvr();
-	if ((SVR_MJREV(svr) >= 2) && (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4))
-		out_be32((void *)MPC5XXX_SDRAM_SDELAY, 0x04);
-
-	return dramsize + dramsize2;
-}
-
-static void get_revisions(int *failsavelevel, int *digiboardversion,
-	int *fpgaversion)
-{
-	struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
-	u8 val;
-
-	/* read digitalboard-version from TMR[2..4] */
-	val = 0;
-	val |= (gpt->gpt2.sr & (1 << (31 - 23))) ? (1) : 0;
-	val |= (gpt->gpt3.sr & (1 << (31 - 23))) ? (1 << 1) : 0;
-	val |= (gpt->gpt4.sr & (1 << (31 - 23))) ? (1 << 2) : 0;
-	*digiboardversion = val;
-
-	/*
-	 * A4M2K only supports digiboardversion. No failsavelevel and
-	 * fpgaversion here.
-	 */
-#if !defined(CONFIG_A4M2K)
-	/*
-	 * Figure out failsavelevel
-	 * see ticket dsvk#59
-	 */
-	*failsavelevel = 0;	/* 0=failsave, 1=board ok, 2=fpga ok */
-
-	if (*digiboardversion == 0) {
-		*failsavelevel = 1;	/* digiboard-version ok */
-
-		/* read fpga-version from TMR[5..7] */
-		val = 0;
-		val |= (gpt->gpt5.sr & (1 << (31 - 23))) ? (1) : 0;
-		val |= (gpt->gpt6.sr & (1 << (31 - 23))) ? (1 << 1) : 0;
-		val |= (gpt->gpt7.sr & (1 << (31 - 23))) ? (1 << 2) : 0;
-		*fpgaversion = val;
-
-		if (*fpgaversion == 1)
-			*failsavelevel = 2;	/* fpga-version ok */
-	}
-#endif
-}
-
-/*
- * This function is called from the SPL U-Boot version for
- * early init stuff, that needs to be done for OS (e.g. Linux)
- * booting. Doing it later in the real U-Boot would not work
- * in case that the SPL U-Boot boots Linux directly.
- */
-void spl_board_init(void)
-{
-	struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
-	struct mpc5xxx_mmap_ctl *mm =
-		(struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR;
-
-#if defined(CONFIG_A4M2K)
-	/* enable CS3 and CS5 (FPGA) */
-	setbits_be32(&mm->ipbi_ws_ctrl, (1 << 19) | (1 << 21));
-#else
-	int digiboardversion;
-	int failsavelevel;
-	int fpgaversion;
-	u32 val;
-
-	get_revisions(&failsavelevel, &digiboardversion, &fpgaversion);
-
-	val = in_be32(&mm->ipbi_ws_ctrl);
-
-	/* first clear bits 19..21 (CS3...5) */
-	val &= ~((1 << 19) | (1 << 20) | (1 << 21));
-	if (failsavelevel == 2) {
-		/* FPGA ok */
-		val |= (1 << 19) | (1 << 21);
-	}
-
-	if (failsavelevel >= 1) {
-		/* at least digiboard-version ok */
-		val |= (1 << 20);
-	}
-
-	/* And write new value back to register */
-	out_be32(&mm->ipbi_ws_ctrl, val);
-
-
-	/* Setup pin multiplexing */
-	if (failsavelevel == 2) {
-		/* fpga-version ok */
-#if defined(CONFIG_SYS_GPS_PORT_CONFIG_2)
-		out_be32(&gpio->port_config, CONFIG_SYS_GPS_PORT_CONFIG_2);
-#endif
-	} else if (failsavelevel == 1) {
-		/* digiboard-version ok - fpga not */
-#if defined(CONFIG_SYS_GPS_PORT_CONFIG_1)
-		out_be32(&gpio->port_config, CONFIG_SYS_GPS_PORT_CONFIG_1);
-#endif
-	} else {
-		/* full failsave-mode */
-#if defined(CONFIG_SYS_GPS_PORT_CONFIG)
-		out_be32(&gpio->port_config, CONFIG_SYS_GPS_PORT_CONFIG);
-#endif
-	}
-#endif
-
-	/*
-	 * Setup gpio_wkup_7 as watchdog AS INPUT to disable it - see
-	 * ticket #60
-	 *
-	 * MPC5XXX_WU_GPIO_DIR direction is already 0 (INPUT)
-	 * set bit 0(msb) to 1
-	 */
-	setbits_be32((void *)MPC5XXX_WU_GPIO_ENABLE, CONFIG_WDOG_GPIO_PIN);
-
-#if defined(CONFIG_A4M2K)
-	/* Setup USB[x] as MPCDiag[0..3] GPIO outputs */
-
-	/* set USB0,6,7,8 (MPCDiag[0..3]) direction to output */
-	gpio->simple_ddr |= 1 << (31 - 15);
-	gpio->simple_ddr |= 1 << (31 - 14);
-	gpio->simple_ddr |= 1 << (31 - 13);
-	gpio->simple_ddr |= 1 << (31 - 12);
-
-	/* enable USB0,6,7,8 (MPCDiag[0..3]) as GPIO */
-	gpio->simple_gpioe |= 1 << (31 - 15);
-	gpio->simple_gpioe |= 1 << (31 - 14);
-	gpio->simple_gpioe |= 1 << (31 - 13);
-	gpio->simple_gpioe |= 1 << (31 - 12);
-
-	/* Setup PSC2[0..2] as STSLED[0..2] GPIO outputs */
-
-	/* set PSC2[0..2] (STSLED[0..2]) direction to output */
-	gpio->simple_ddr |= 1 << (31 - 27);
-	gpio->simple_ddr |= 1 << (31 - 26);
-	gpio->simple_ddr |= 1 << (31 - 25);
-
-	/* enable PSC2[0..2] (STSLED[0..2]) as GPIO */
-	gpio->simple_gpioe |= 1 << (31 - 27);
-	gpio->simple_gpioe |= 1 << (31 - 26);
-	gpio->simple_gpioe |= 1 << (31 - 25);
-
-	/* Setup PSC6[2] as MRST2 self reset GPIO output */
-
-	/* set PSC6[2]/IRDA_TX (MRST2) direction to output */
-	gpio->simple_ddr |= 1 << (31 - 3);
-
-	/* set PSC6[2]/IRDA_TX (MRST2) output as open drain */
-	gpio->simple_ode |= 1 << (31 - 3);
-
-	/* set PSC6[2]/IRDA_TX (MRST2) output as default high */
-	gpio->simple_dvo |= 1 << (31 - 3);
-
-	/* enable PSC6[2]/IRDA_TX (MRST2) as GPIO */
-	gpio->simple_gpioe |= 1 << (31 - 3);
-
-	/* Setup PSC6[3] as HARNSSCD harness code GPIO input */
-
-	/* set PSC6[3]/IR_USB_CLK (HARNSSCD) direction to input */
-	gpio->simple_ddr |= 0 << (31 - 2);
-
-	/* enable PSC6[3]/IR_USB_CLK (HARNSSCD) as GPIO */
-	gpio->simple_gpioe |= 1 << (31 - 2);
-#else
-	/* setup GPIOs for status-leds if needed - see ticket #57 */
-	if (failsavelevel > 0) {
-		/* digiboard-version is OK */
-		/* LED is LOW ACTIVE - so deactivate by set output to 1 */
-		gpio->simple_dvo |= 1 << (31 - 12);
-		gpio->simple_dvo |= 1 << (31 - 13);
-		/* set GPIO direction to output */
-		gpio->simple_ddr |= 1 << (31 - 12);
-		gpio->simple_ddr |= 1 << (31 - 13);
-		/* open drain config is set to "normal output" at reset */
-		/* gpio->simple_ode &=~ ( 1 << (31-12) ); */
-		/* gpio->simple_ode &=~ ( 1 << (31-13) ); */
-		/* enable as GPIO */
-		gpio->simple_gpioe |= 1 << (31 - 12);
-		gpio->simple_gpioe |= 1 << (31 - 13);
-	}
-
-	/* setup fpga irq - see ticket #65 */
-	if (failsavelevel > 1) {
-		/*
-		 * The main irq initialisation is done in interrupts.c
-		 * mpc5xxx_init_irq
-		 */
-		struct mpc5xxx_intr *intr =
-		    (struct mpc5xxx_intr *)(MPC5XXX_ICTL);
-
-		setbits_be32(&intr->ctrl, 0x08C01801);
-
-		/*
-		 * The MBAR+0x0524 Bit 21:23 CSe are ignored here due to the
-		 * already cleared (intr_ctrl) MBAR+0x0510 ECLR[0] bit above
-		 */
-	}
-#endif
-}
-
-int checkboard(void)
-{
-	int digiboardversion;
-	int failsavelevel;
-	int fpgaversion;
-
-	get_revisions(&failsavelevel, &digiboardversion, &fpgaversion);
-
-#ifdef CONFIG_A4M2K
-	puts("Board: A4M2K\n");
-	printf("       digiboard IO version %u\n", digiboardversion);
-#else
-	puts("Board: A3M071\n");
-	printf("Rev:   failsave level       %u\n", failsavelevel);
-	printf("       digiboard IO version %u\n", digiboardversion);
-	if (failsavelevel > 0)	/* only if fpga-version red */
-		printf("       fpga IO version      %u\n", fpgaversion);
-#endif
-
-	return 0;
-}
-
-/* miscellaneous platform dependent initialisations */
-int misc_init_r(void)
-{
-	/* adjust flash start and offset to detected values */
-	gd->bd->bi_flashstart = flash_info[0].start[0];
-	gd->bd->bi_flashoffset = 0;
-
-	/* adjust mapping */
-	out_be32((void *)MPC5XXX_BOOTCS_START,
-		 START_REG(gd->bd->bi_flashstart));
-	out_be32((void *)MPC5XXX_CS0_START, START_REG(gd->bd->bi_flashstart));
-	out_be32((void *)MPC5XXX_BOOTCS_STOP,
-		 STOP_REG(gd->bd->bi_flashstart, gd->bd->bi_flashsize));
-	out_be32((void *)MPC5XXX_CS0_STOP,
-		 STOP_REG(gd->bd->bi_flashstart, gd->bd->bi_flashsize));
-
-	return 0;
-}
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t * bd)
-{
-	ft_cpu_setup(blob, bd);
-}
-#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */
-
-#ifdef CONFIG_SPL_OS_BOOT
-/*
- * A3M071 specific implementation of spl_start_uboot()
- *
- * RETURN
- * 0 if booting into OS is selected (default)
- * 1 if booting into U-Boot is selected
- */
-int spl_start_uboot(void)
-{
-	char s[8];
-
-	env_init();
-	getenv_f("boot_os", s, sizeof(s));
-	if ((s != NULL) && (*s == '1' || *s == 'y' || *s == 'Y' ||
-			    *s == 't' || *s == 'T'))
-		return 0;
-
-	return 1;
-}
-#endif
-
-#if defined(CONFIG_HW_WATCHDOG)
-static int watchdog_toggle;
-
-void hw_watchdog_reset(void)
-{
-	int val;
-
-	/*
-	 * Check if watchdog is enabled via user command
-	 */
-	if ((gd->flags & GD_FLG_RELOC) && watchdog_toggle) {
-		/* Set direction to output */
-		setbits_be32((void *)MPC5XXX_WU_GPIO_DIR, CONFIG_WDOG_GPIO_PIN);
-
-		/*
-		 * Toggle watchdog output
-		 */
-		val = (in_be32((void *)MPC5XXX_WU_GPIO_DATA_O) &
-		       CONFIG_WDOG_GPIO_PIN);
-		if (val) {
-			clrbits_be32((void *)MPC5XXX_WU_GPIO_DATA_O,
-				     CONFIG_WDOG_GPIO_PIN);
-		} else {
-			setbits_be32((void *)MPC5XXX_WU_GPIO_DATA_O,
-				     CONFIG_WDOG_GPIO_PIN);
-		}
-	}
-}
-
-int do_wdog_toggle(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	if (argc != 2)
-		goto usage;
-
-	if (strncmp(argv[1], "on", 2) == 0)
-		watchdog_toggle = 1;
-	else if (strncmp(argv[1], "off", 3) == 0)
-		watchdog_toggle = 0;
-	else
-		goto usage;
-
-	return 0;
-usage:
-	printf("Usage: wdogtoggle %s\n", cmdtp->usage);
-	return 1;
-}
-
-U_BOOT_CMD(
-	wdogtoggle, CONFIG_SYS_MAXARGS, 2, do_wdog_toggle,
-	"toggle GPIO pin to service watchdog",
-	"[on/off] - Switch watchdog toggling via GPIO pin on/off"
-);
-#endif
diff --git a/qemu/roms/u-boot/board/a3m071/is46r16320d.h b/qemu/roms/u-boot/board/a3m071/is46r16320d.h
deleted file mode 100644
index 981359f22..000000000
--- a/qemu/roms/u-boot/board/a3m071/is46r16320d.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#define SDRAM_DDR		/* is DDR */
-
-#if defined(CONFIG_MPC5200)
-/* Settings for XLB = 132 MHz */
-/* see is46r16320d datasheet and MPC5200UM chap. 8.6.1. */
-
-/* SDRAM Config Standard timing */
-#define SDRAM_MODE	0x008d0000
-#define SDRAM_EMODE	0x40010000
-#define SDRAM_CONTROL	0x70430f00
-#define SDRAM_CONFIG1	0x33622930
-#define SDRAM_CONFIG2	0x46670000
-#define SDRAM_TAPDELAY	0x10000000
-
-#else
-#error CONFIG_MPC5200 not defined
-#endif
diff --git a/qemu/roms/u-boot/board/a3m071/mt46v16m16-75.h b/qemu/roms/u-boot/board/a3m071/mt46v16m16-75.h
deleted file mode 100644
index 8f428306f..000000000
--- a/qemu/roms/u-boot/board/a3m071/mt46v16m16-75.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#define SDRAM_DDR		/* is DDR */
-
-#if defined(CONFIG_MPC5200)
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE	0x018D0000
-#define SDRAM_EMODE	0x40090000
-#define SDRAM_CONTROL	0x704f0f00
-#define SDRAM_CONFIG1	0x73722930
-#define SDRAM_CONFIG2	0x47770000
-#define SDRAM_TAPDELAY	0x10000000
-
-#else
-#error CONFIG_MPC5200 not defined
-#endif