Add qemu 2.4.0

Change-Id: Ic99cbad4b61f8b127b7dc74d04576c0bcbaaf4f5
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>

4 files changed, 321 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/Marvell/dreamplug/Makefile b/qemu/roms/u-boot/board/Marvell/dreamplug/Makefile
new file mode 100644
index 000000000..23e6c5318
--- /dev/null
+++ b/qemu/roms/u-boot/board/Marvell/dreamplug/Makefile
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2011
+# Jason Cooper <u-boot@lakedaemon.net>
+#
+# Based on work by:
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Siddarth Gore <gores@marvell.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= dreamplug.o
diff --git a/qemu/roms/u-boot/board/Marvell/dreamplug/dreamplug.c b/qemu/roms/u-boot/board/Marvell/dreamplug/dreamplug.c
new file mode 100644
index 000000000..b53c81080
--- /dev/null
+++ b/qemu/roms/u-boot/board/Marvell/dreamplug/dreamplug.c
@@ -0,0 +1,136 @@
+/*
+ * (C) Copyright 2011
+ * Jason Cooper <u-boot@lakedaemon.net>
+ *
+ * Based on work by:
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Siddarth Gore <gores@marvell.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "dreamplug.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	/*
+	 * default gpio configuration
+	 * There are maximum 64 gpios controlled through 2 sets of registers
+	 * the  below configuration configures mainly initial LED status
+	 */
+	kw_config_gpio(DREAMPLUG_OE_VAL_LOW,
+			DREAMPLUG_OE_VAL_HIGH,
+			DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH);
+
+	/* Multi-Purpose Pins Functionality configuration */
+	static const u32 kwmpp_config[] = {
+		MPP0_SPI_SCn,		/* SPI Flash */
+		MPP1_SPI_MOSI,
+		MPP2_SPI_SCK,
+		MPP3_SPI_MISO,
+		MPP4_NF_IO6,
+		MPP5_NF_IO7,
+		MPP6_SYSRST_OUTn,
+		MPP7_GPO,
+		MPP8_TW_SDA,
+		MPP9_TW_SCK,
+		MPP10_UART0_TXD,	/* Serial */
+		MPP11_UART0_RXD,
+		MPP12_SD_CLK,		/* SDIO Slot */
+		MPP13_SD_CMD,
+		MPP14_SD_D0,
+		MPP15_SD_D1,
+		MPP16_SD_D2,
+		MPP17_SD_D3,
+		MPP18_NF_IO0,
+		MPP19_NF_IO1,
+		MPP20_GE1_0,		/* Gigabit Ethernet */
+		MPP21_GE1_1,
+		MPP22_GE1_2,
+		MPP23_GE1_3,
+		MPP24_GE1_4,
+		MPP25_GE1_5,
+		MPP26_GE1_6,
+		MPP27_GE1_7,
+		MPP28_GE1_8,
+		MPP29_GE1_9,
+		MPP30_GE1_10,
+		MPP31_GE1_11,
+		MPP32_GE1_12,
+		MPP33_GE1_13,
+		MPP34_GE1_14,
+		MPP35_GE1_15,
+		MPP36_GPIO,		/* 7 external GPIO pins (36 - 45) */
+		MPP37_GPIO,
+		MPP38_GPIO,
+		MPP39_GPIO,
+		MPP40_TDM_SPI_SCK,
+		MPP41_TDM_SPI_MISO,
+		MPP42_TDM_SPI_MOSI,
+		MPP43_GPIO,
+		MPP44_GPIO,
+		MPP45_GPIO,
+		MPP46_GPIO,
+		MPP47_GPIO,		/* Bluetooth LED */
+		MPP48_GPIO,		/* Wifi LED */
+		MPP49_GPIO,		/* Wifi AP LED */
+		0
+	};
+	kirkwood_mpp_conf(kwmpp_config, NULL);
+	return 0;
+}
+
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+void mv_phy_88e1116_init(char *name)
+{
+	u16 reg;
+	u16 devadr;
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+		printf("Err..%s could not read PHY dev address\n",
+			__func__);
+		return;
+	}
+
+	/*
+	 * Enable RGMII delay on Tx and Rx for CPU port
+	 * Ref: sec 4.7.2 of chip datasheet
+	 */
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+	miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, &reg);
+	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+	miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg);
+	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+	/* reset the phy */
+	miiphy_reset(name, devadr);
+
+	printf("88E1116 Initialized on %s\n", name);
+}
+
+void reset_phy(void)
+{
+	/* configure and initialize both PHY's */
+	mv_phy_88e1116_init("egiga0");
+	mv_phy_88e1116_init("egiga1");
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/qemu/roms/u-boot/board/Marvell/dreamplug/dreamplug.h b/qemu/roms/u-boot/board/Marvell/dreamplug/dreamplug.h
new file mode 100644
index 000000000..18ea41cba
--- /dev/null
+++ b/qemu/roms/u-boot/board/Marvell/dreamplug/dreamplug.h
@@ -0,0 +1,26 @@
+/*
+ * (C) Copyright 2011
+ * Jason Cooper <u-boot@lakedaemon.net>
+ *
+ * Based on work by:
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Siddarth Gore <gores@marvell.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __DREAMPLUG_H
+#define __DREAMPLUG_H
+
+#define DREAMPLUG_OE_LOW	(~(0))
+#define DREAMPLUG_OE_HIGH	(~(0))
+#define DREAMPLUG_OE_VAL_LOW	0
+#define DREAMPLUG_OE_VAL_HIGH	(0xf << 16) /* 4 LED Pins high */
+
+/* PHY related */
+#define MV88E1116_MAC_CTRL2_REG		21
+#define MV88E1116_PGADR_REG		22
+#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
+
+#endif /* __DREAMPLUG_H */
diff --git a/qemu/roms/u-boot/board/Marvell/dreamplug/kwbimage.cfg b/qemu/roms/u-boot/board/Marvell/dreamplug/kwbimage.cfg
new file mode 100644
index 000000000..19d77e3a1
--- /dev/null
+++ b/qemu/roms/u-boot/board/Marvell/dreamplug/kwbimage.cfg
@@ -0,0 +1,147 @@
+#
+# (C) Copyright 2011
+# Jason Cooper <u-boot@lakedaemon.net>
+#
+# Based on work by:
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Siddarth Gore <gores@marvell.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+# Refer doc/README.kwbimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	spi
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0/1 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b9b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30	# DDR Configuration register
+# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
+# bit3-0:   TRAS lsbs
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc	#  DDR Address Control
+# bit1-0:   01, Cs0width=x8
+# bit3-2:   10, Cs0size=1Gb
+# bit5-4:   01, Cs1width=x8
+# bit7-6:   10, Cs1size=1Gb
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000C52	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    0,  DDR drive strenght normal
+# bit2:    0,  DDR ODT control lsd (disabled)
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, (disabled)
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  0
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0