These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

33 files changed, 369 insertions, 453 deletions

diff --git a/kernel/include/linux/platform_data/atmel.h b/kernel/include/linux/platform_data/atmel.h
index 4b452c6a2..3c8825b67 100644
--- a/kernel/include/linux/platform_data/atmel.h
+++ b/kernel/include/linux/platform_data/atmel.h
@@ -9,30 +9,7 @@
 
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
-#include <linux/device.h>
-#include <linux/i2c.h>
-#include <linux/leds.h>
-#include <linux/spi/spi.h>
-#include <linux/usb/atmel_usba_udc.h>
-#include <linux/atmel-mci.h>
-#include <sound/atmel-ac97c.h>
 #include <linux/serial.h>
-#include <linux/platform_data/macb.h>
-
-/*
- * at91: 6 USARTs and one DBGU port (SAM9260)
- * avr32: 4
- */
-#define ATMEL_MAX_UART	7
-
- /* USB Device */
-struct at91_udc_data {
-	int	vbus_pin;		/* high == host powering us */
-	u8	vbus_active_low;	/* vbus polarity */
-	u8	vbus_polled;		/* Use polling, not interrupt */
-	int	pullup_pin;		/* active == D+ pulled up */
-	u8	pullup_active_low;	/* true == pullup_pin is active low */
-};
 
  /* Compact Flash */
 struct at91_cf_data {
@@ -46,18 +23,6 @@ struct at91_cf_data {
 #define AT91_IDE_SWAP_A0_A2	0x02
 };
 
- /* USB Host */
-#define AT91_MAX_USBH_PORTS	3
-struct at91_usbh_data {
-	int		vbus_pin[AT91_MAX_USBH_PORTS];	/* port power-control pin */
-	int             overcurrent_pin[AT91_MAX_USBH_PORTS];
-	u8		ports;				/* number of ports on root hub */
-	u8              overcurrent_supported;
-	u8              vbus_pin_active_low[AT91_MAX_USBH_PORTS];
-	u8              overcurrent_status[AT91_MAX_USBH_PORTS];
-	u8              overcurrent_changed[AT91_MAX_USBH_PORTS];
-};
-
  /* NAND / SmartMedia */
 struct atmel_nand_data {
 	int		enable_pin;		/* chip enable */
@@ -86,11 +51,6 @@ struct atmel_uart_data {
 	struct serial_rs485	rs485;		/* rs485 settings */
 };
 
-/* CAN */
-struct at91_can_data {
-	void (*transceiver_switch)(int on);
-};
-
 /* FIXME: this needs a better location, but gets stuff building again */
 extern int at91_suspend_entering_slow_clock(void);
 
diff --git a/kernel/include/linux/platform_data/atmel_mxt_ts.h b/kernel/include/linux/platform_data/atmel_mxt_ts.h
new file mode 100644
index 000000000..695035a8d
--- /dev/null
+++ b/kernel/include/linux/platform_data/atmel_mxt_ts.h
@@ -0,0 +1,31 @@
+/*
+ * Atmel maXTouch Touchscreen driver
+ *
+ * Copyright (C) 2010 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_ATMEL_MXT_TS_H
+#define __LINUX_PLATFORM_DATA_ATMEL_MXT_TS_H
+
+#include <linux/types.h>
+
+enum mxt_suspend_mode {
+	MXT_SUSPEND_DEEP_SLEEP	= 0,
+	MXT_SUSPEND_T9_CTRL	= 1,
+};
+
+/* The platform data for the Atmel maXTouch touchscreen driver */
+struct mxt_platform_data {
+	unsigned long irqflags;
+	u8 t19_num_keys;
+	const unsigned int *t19_keymap;
+	enum mxt_suspend_mode suspend_mode;
+};
+
+#endif /* __LINUX_PLATFORM_DATA_ATMEL_MXT_TS_H */
diff --git a/kernel/include/linux/platform_data/clk-ux500.h b/kernel/include/linux/platform_data/clk-ux500.h
index 97baf831e..3af0da1f3 100644
--- a/kernel/include/linux/platform_data/clk-ux500.h
+++ b/kernel/include/linux/platform_data/clk-ux500.h
@@ -10,14 +10,8 @@
 #ifndef __CLK_UX500_H
 #define __CLK_UX500_H
 
-void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
-		       u32 clkrst5_base, u32 clkrst6_base);
-
-void u8500_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
-		    u32 clkrst5_base, u32 clkrst6_base);
-void u9540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
-		    u32 clkrst5_base, u32 clkrst6_base);
-void u8540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base,
-		    u32 clkrst5_base, u32 clkrst6_base);
+void u8500_clk_init(void);
+void u9540_clk_init(void);
+void u8540_clk_init(void);
 
 #endif /* __CLK_UX500_H */
diff --git a/kernel/include/linux/platform_data/dma-dw.h b/kernel/include/linux/platform_data/dma-dw.h
index 87ac14c58..03b6095d3 100644
--- a/kernel/include/linux/platform_data/dma-dw.h
+++ b/kernel/include/linux/platform_data/dma-dw.h
@@ -37,6 +37,7 @@ struct dw_dma_slave {
  * @nr_channels: Number of channels supported by hardware (max 8)
  * @is_private: The device channels should be marked as private and not for
  *	by the general purpose DMA channel allocator.
+ * @is_memcpy: The device channels do support memory-to-memory transfers.
  * @chan_allocation_order: Allocate channels starting from 0 or 7
  * @chan_priority: Set channel priority increasing from 0 to 7 or 7 to 0.
  * @block_size: Maximum block size supported by the controller
@@ -47,6 +48,7 @@ struct dw_dma_slave {
 struct dw_dma_platform_data {
 	unsigned int	nr_channels;
 	bool		is_private;
+	bool		is_memcpy;
 #define CHAN_ALLOCATION_ASCENDING	0	/* zero to seven */
 #define CHAN_ALLOCATION_DESCENDING	1	/* seven to zero */
 	unsigned char	chan_allocation_order;
diff --git a/kernel/include/linux/platform_data/dma-hsu.h b/kernel/include/linux/platform_data/dma-hsu.h
index 8a1f6a492..3453fa655 100644
--- a/kernel/include/linux/platform_data/dma-hsu.h
+++ b/kernel/include/linux/platform_data/dma-hsu.h
@@ -18,8 +18,4 @@ struct hsu_dma_slave {
 	int		chan_id;
 };
 
-struct hsu_dma_platform_data {
-	unsigned short	nr_channels;
-};
-
 #endif /* _PLATFORM_DATA_DMA_HSU_H */
diff --git a/kernel/include/linux/platform_data/dma-rcar-audmapp.h b/kernel/include/linux/platform_data/dma-rcar-audmapp.h
deleted file mode 100644
index 471fffebb..000000000
--- a/kernel/include/linux/platform_data/dma-rcar-audmapp.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * This is for Renesas R-Car Audio-DMAC-peri-peri.
- *
- * Copyright (C) 2014 Renesas Electronics Corporation
- * Copyright (C) 2014 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This file is based on the include/linux/sh_dma.h
- *
- * Header for the new SH dmaengine driver
- *
- * Copyright (C) 2010 Guennadi Liakhovetski <g.liakhovetski@gmx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef SH_AUDMAPP_H
-#define SH_AUDMAPP_H
-
-#include <linux/dmaengine.h>
-
-struct audmapp_slave_config {
-	int		slave_id;
-	dma_addr_t	src;
-	dma_addr_t	dst;
-	u32		chcr;
-};
-
-struct audmapp_pdata {
-	struct audmapp_slave_config *slave;
-	int slave_num;
-};
-
-#endif /* SH_AUDMAPP_H */
diff --git a/kernel/include/linux/platform_data/edma.h b/kernel/include/linux/platform_data/edma.h
index bdb2710e2..4299f4ba0 100644
--- a/kernel/include/linux/platform_data/edma.h
+++ b/kernel/include/linux/platform_data/edma.h
@@ -41,51 +41,6 @@
 #ifndef EDMA_H_
 #define EDMA_H_
 
-/* PaRAM slots are laid out like this */
-struct edmacc_param {
-	u32 opt;
-	u32 src;
-	u32 a_b_cnt;
-	u32 dst;
-	u32 src_dst_bidx;
-	u32 link_bcntrld;
-	u32 src_dst_cidx;
-	u32 ccnt;
-} __packed;
-
-/* fields in edmacc_param.opt */
-#define SAM		BIT(0)
-#define DAM		BIT(1)
-#define SYNCDIM		BIT(2)
-#define STATIC		BIT(3)
-#define EDMA_FWID	(0x07 << 8)
-#define TCCMODE		BIT(11)
-#define EDMA_TCC(t)	((t) << 12)
-#define TCINTEN		BIT(20)
-#define ITCINTEN	BIT(21)
-#define TCCHEN		BIT(22)
-#define ITCCHEN		BIT(23)
-
-/*ch_status paramater of callback function possible values*/
-#define EDMA_DMA_COMPLETE 1
-#define EDMA_DMA_CC_ERROR 2
-#define EDMA_DMA_TC1_ERROR 3
-#define EDMA_DMA_TC2_ERROR 4
-
-enum address_mode {
-	INCR = 0,
-	FIFO = 1
-};
-
-enum fifo_width {
-	W8BIT = 0,
-	W16BIT = 1,
-	W32BIT = 2,
-	W64BIT = 3,
-	W128BIT = 4,
-	W256BIT = 5
-};
-
 enum dma_event_q {
 	EVENTQ_0 = 0,
 	EVENTQ_1 = 1,
@@ -94,64 +49,10 @@ enum dma_event_q {
 	EVENTQ_DEFAULT = -1
 };
 
-enum sync_dimension {
-	ASYNC = 0,
-	ABSYNC = 1
-};
-
 #define EDMA_CTLR_CHAN(ctlr, chan)	(((ctlr) << 16) | (chan))
 #define EDMA_CTLR(i)			((i) >> 16)
 #define EDMA_CHAN_SLOT(i)		((i) & 0xffff)
 
-#define EDMA_CHANNEL_ANY		-1	/* for edma_alloc_channel() */
-#define EDMA_SLOT_ANY			-1	/* for edma_alloc_slot() */
-#define EDMA_CONT_PARAMS_ANY		 1001
-#define EDMA_CONT_PARAMS_FIXED_EXACT	 1002
-#define EDMA_CONT_PARAMS_FIXED_NOT_EXACT 1003
-
-#define EDMA_MAX_CC               2
-
-/* alloc/free DMA channels and their dedicated parameter RAM slots */
-int edma_alloc_channel(int channel,
-	void (*callback)(unsigned channel, u16 ch_status, void *data),
-	void *data, enum dma_event_q);
-void edma_free_channel(unsigned channel);
-
-/* alloc/free parameter RAM slots */
-int edma_alloc_slot(unsigned ctlr, int slot);
-void edma_free_slot(unsigned slot);
-
-/* alloc/free a set of contiguous parameter RAM slots */
-int edma_alloc_cont_slots(unsigned ctlr, unsigned int id, int slot, int count);
-int edma_free_cont_slots(unsigned slot, int count);
-
-/* calls that operate on part of a parameter RAM slot */
-void edma_set_src(unsigned slot, dma_addr_t src_port,
-				enum address_mode mode, enum fifo_width);
-void edma_set_dest(unsigned slot, dma_addr_t dest_port,
-				 enum address_mode mode, enum fifo_width);
-dma_addr_t edma_get_position(unsigned slot, bool dst);
-void edma_set_src_index(unsigned slot, s16 src_bidx, s16 src_cidx);
-void edma_set_dest_index(unsigned slot, s16 dest_bidx, s16 dest_cidx);
-void edma_set_transfer_params(unsigned slot, u16 acnt, u16 bcnt, u16 ccnt,
-		u16 bcnt_rld, enum sync_dimension sync_mode);
-void edma_link(unsigned from, unsigned to);
-void edma_unlink(unsigned from);
-
-/* calls that operate on an entire parameter RAM slot */
-void edma_write_slot(unsigned slot, const struct edmacc_param *params);
-void edma_read_slot(unsigned slot, struct edmacc_param *params);
-
-/* channel control operations */
-int edma_start(unsigned channel);
-void edma_stop(unsigned channel);
-void edma_clean_channel(unsigned channel);
-void edma_clear_event(unsigned channel);
-void edma_pause(unsigned channel);
-void edma_resume(unsigned channel);
-
-void edma_assign_channel_eventq(unsigned channel, enum dma_event_q eventq_no);
-
 struct edma_rsv_info {
 
 	const s16	(*rsv_chans)[2];
@@ -170,10 +71,11 @@ struct edma_soc_info {
 	/* Resource reservation for other cores */
 	struct edma_rsv_info	*rsv;
 
+	/* List of channels allocated for memcpy, terminated with -1 */
+	s32			*memcpy_channels;
+
 	s8	(*queue_priority_mapping)[2];
 	const s16	(*xbar_chans)[2];
 };
 
-int edma_trigger_channel(unsigned);
-
 #endif
diff --git a/kernel/include/linux/platform_data/gpio-ath79.h b/kernel/include/linux/platform_data/gpio-ath79.h
new file mode 100644
index 000000000..88b0db7be
--- /dev/null
+++ b/kernel/include/linux/platform_data/gpio-ath79.h
@@ -0,0 +1,19 @@
+/*
+ *  Atheros AR7XXX/AR9XXX GPIO controller platform data
+ *
+ * Copyright (C) 2015 Alban Bedel <albeu@free.fr>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_GPIO_ATH79_H
+#define __LINUX_PLATFORM_DATA_GPIO_ATH79_H
+
+struct ath79_gpio_platform_data {
+	unsigned ngpios;
+	bool oe_inverted;
+};
+
+#endif
diff --git a/kernel/include/linux/platform_data/gpio-em.h b/kernel/include/linux/platform_data/gpio-em.h
deleted file mode 100644
index 7c5a519d2..000000000
--- a/kernel/include/linux/platform_data/gpio-em.h
+++ /dev/null
@@ -1,11 +0,0 @@
-#ifndef __GPIO_EM_H__
-#define __GPIO_EM_H__
-
-struct gpio_em_config {
-	unsigned int gpio_base;
-	unsigned int irq_base;
-	unsigned int number_of_pins;
-	const char *pctl_name;
-};
-
-#endif /* __GPIO_EM_H__ */
diff --git a/kernel/include/linux/platform_data/gpio-omap.h b/kernel/include/linux/platform_data/gpio-omap.h
index 5d50b25a7..cb2618147 100644
--- a/kernel/include/linux/platform_data/gpio-omap.h
+++ b/kernel/include/linux/platform_data/gpio-omap.h
@@ -208,9 +208,17 @@ struct omap_gpio_platform_data {
 	int (*get_context_loss_count)(struct device *dev);
 };
 
+#if IS_BUILTIN(CONFIG_GPIO_OMAP)
 extern void omap2_gpio_prepare_for_idle(int off_mode);
 extern void omap2_gpio_resume_after_idle(void);
-extern void omap_set_gpio_debounce(int gpio, int enable);
-extern void omap_set_gpio_debounce_time(int gpio, int enable);
+#else
+static inline void omap2_gpio_prepare_for_idle(int off_mode)
+{
+}
+
+static inline void omap2_gpio_resume_after_idle(void)
+{
+}
+#endif
 
 #endif
diff --git a/kernel/include/linux/platform_data/i2c-mux-reg.h b/kernel/include/linux/platform_data/i2c-mux-reg.h
new file mode 100644
index 000000000..c68712aad
--- /dev/null
+++ b/kernel/include/linux/platform_data/i2c-mux-reg.h
@@ -0,0 +1,44 @@
+/*
+ * I2C multiplexer using a single register
+ *
+ * Copyright 2015 Freescale Semiconductor
+ * York Sun <yorksun@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_I2C_MUX_REG_H
+#define __LINUX_PLATFORM_DATA_I2C_MUX_REG_H
+
+/**
+ * struct i2c_mux_reg_platform_data - Platform-dependent data for i2c-mux-reg
+ * @parent: Parent I2C bus adapter number
+ * @base_nr: Base I2C bus number to number adapters from or zero for dynamic
+ * @values: Array of value for each channel
+ * @n_values: Number of multiplexer channels
+ * @little_endian: Indicating if the register is in little endian
+ * @write_only: Reading the register is not allowed by hardware
+ * @classes: Optional I2C auto-detection classes
+ * @idle: Value to write to mux when idle
+ * @idle_in_use: indicate if idle value is in use
+ * @reg: Virtual address of the register to switch channel
+ * @reg_size: register size in bytes
+ */
+struct i2c_mux_reg_platform_data {
+	int parent;
+	int base_nr;
+	const unsigned int *values;
+	int n_values;
+	bool little_endian;
+	bool write_only;
+	const unsigned int *classes;
+	u32 idle;
+	bool idle_in_use;
+	void __iomem *reg;
+	resource_size_t reg_size;
+};
+
+#endif	/* __LINUX_PLATFORM_DATA_I2C_MUX_REG_H */
diff --git a/kernel/include/linux/platform_data/irq-renesas-irqc.h b/kernel/include/linux/platform_data/irq-renesas-irqc.h
deleted file mode 100644
index 3ae17b3e0..000000000
--- a/kernel/include/linux/platform_data/irq-renesas-irqc.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * Renesas IRQC Driver
- *
- *  Copyright (C) 2013 Magnus Damm
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#ifndef __IRQ_RENESAS_IRQC_H__
-#define __IRQ_RENESAS_IRQC_H__
-
-struct renesas_irqc_config {
-	unsigned int irq_base;
-};
-
-#endif /* __IRQ_RENESAS_IRQC_H__ */
diff --git a/kernel/include/linux/platform_data/itco_wdt.h b/kernel/include/linux/platform_data/itco_wdt.h
new file mode 100644
index 000000000..f16542c77
--- /dev/null
+++ b/kernel/include/linux/platform_data/itco_wdt.h
@@ -0,0 +1,19 @@
+/*
+ * Platform data for the Intel TCO Watchdog
+ */
+
+#ifndef _ITCO_WDT_H_
+#define _ITCO_WDT_H_
+
+/* Watchdog resources */
+#define ICH_RES_IO_TCO		0
+#define ICH_RES_IO_SMI		1
+#define ICH_RES_MEM_OFF		2
+#define ICH_RES_MEM_GCS_PMC	0
+
+struct itco_wdt_platform_data {
+	char name[32];
+	unsigned int version;
+};
+
+#endif /* _ITCO_WDT_H_ */
diff --git a/kernel/include/linux/platform_data/keyboard-spear.h b/kernel/include/linux/platform_data/keyboard-spear.h
index 9248e3a7e..5e3ff6539 100644
--- a/kernel/include/linux/platform_data/keyboard-spear.h
+++ b/kernel/include/linux/platform_data/keyboard-spear.h
@@ -1,6 +1,6 @@
 /*
  * Copyright (C) 2010 ST Microelectronics
- * Rajeev Kumar<rajeev-dlh.kumar@st.com>
+ * Rajeev Kumar <rajeevkumar.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any
diff --git a/kernel/include/linux/platform_data/leds-kirkwood-netxbig.h b/kernel/include/linux/platform_data/leds-kirkwood-netxbig.h
index d2be19a51..3c85a735c 100644
--- a/kernel/include/linux/platform_data/leds-kirkwood-netxbig.h
+++ b/kernel/include/linux/platform_data/leds-kirkwood-netxbig.h
@@ -40,6 +40,7 @@ struct netxbig_led {
 	int		mode_addr;
 	int		*mode_val;
 	int		bright_addr;
+	int		bright_max;
 };
 
 struct netxbig_led_platform_data {
diff --git a/kernel/include/linux/platform_data/leds-kirkwood-ns2.h b/kernel/include/linux/platform_data/leds-kirkwood-ns2.h
index 6a9fed57f..eb8a6860e 100644
--- a/kernel/include/linux/platform_data/leds-kirkwood-ns2.h
+++ b/kernel/include/linux/platform_data/leds-kirkwood-ns2.h
@@ -9,11 +9,25 @@
 #ifndef __LEDS_KIRKWOOD_NS2_H
 #define __LEDS_KIRKWOOD_NS2_H
 
+enum ns2_led_modes {
+	NS_V2_LED_OFF,
+	NS_V2_LED_ON,
+	NS_V2_LED_SATA,
+};
+
+struct ns2_led_modval {
+	enum ns2_led_modes	mode;
+	int			cmd_level;
+	int			slow_level;
+};
+
 struct ns2_led {
 	const char	*name;
 	const char	*default_trigger;
 	unsigned	cmd;
 	unsigned	slow;
+	int		num_modes;
+	struct ns2_led_modval *modval;
 };
 
 struct ns2_led_platform_data {
diff --git a/kernel/include/linux/platform_data/lp855x.h b/kernel/include/linux/platform_data/lp855x.h
index 9c7fd1efe..1b2ba24e4 100644
--- a/kernel/include/linux/platform_data/lp855x.h
+++ b/kernel/include/linux/platform_data/lp855x.h
@@ -136,7 +136,6 @@ struct lp855x_rom_data {
 		Only valid when mode is PWM_BASED.
  * @size_program : total size of lp855x_rom_data
  * @rom_data : list of new eeprom/eprom registers
- * @supply : regulator that supplies 3V input
  */
 struct lp855x_platform_data {
 	const char *name;
@@ -145,7 +144,6 @@ struct lp855x_platform_data {
 	unsigned int period_ns;
 	int size_program;
 	struct lp855x_rom_data *rom_data;
-	struct regulator *supply;
 };
 
 #endif
diff --git a/kernel/include/linux/platform_data/macb.h b/kernel/include/linux/platform_data/macb.h
index 044a124bf..21b15f6fe 100644
--- a/kernel/include/linux/platform_data/macb.h
+++ b/kernel/include/linux/platform_data/macb.h
@@ -8,11 +8,19 @@
 #ifndef __MACB_PDATA_H__
 #define __MACB_PDATA_H__
 
+/**
+ * struct macb_platform_data - platform data for MACB Ethernet
+ * @phy_mask:		phy mask passed when register the MDIO bus
+ *			within the driver
+ * @phy_irq_pin:	PHY IRQ
+ * @is_rmii:		using RMII interface?
+ * @rev_eth_addr:	reverse Ethernet address byte order
+ */
 struct macb_platform_data {
 	u32		phy_mask;
-	int		phy_irq_pin;	/* PHY IRQ */
-	u8		is_rmii;	/* using RMII interface? */
-	u8		rev_eth_addr;	/* reverse Ethernet address byte order */
+	int		phy_irq_pin;
+	u8		is_rmii;
+	u8		rev_eth_addr;
 };
 
 #endif /* __MACB_PDATA_H__ */
diff --git a/kernel/include/linux/platform_data/mdio-gpio.h b/kernel/include/linux/platform_data/mdio-gpio.h
new file mode 100644
index 000000000..11f00cdab
--- /dev/null
+++ b/kernel/include/linux/platform_data/mdio-gpio.h
@@ -0,0 +1,33 @@
+/*
+ * MDIO-GPIO bus platform data structures
+ *
+ * Copyright (C) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __LINUX_MDIO_GPIO_H
+#define __LINUX_MDIO_GPIO_H
+
+#include <linux/mdio-bitbang.h>
+
+struct mdio_gpio_platform_data {
+	/* GPIO numbers for bus pins */
+	unsigned int mdc;
+	unsigned int mdio;
+	unsigned int mdo;
+
+	bool mdc_active_low;
+	bool mdio_active_low;
+	bool mdo_active_low;
+
+	u32 phy_mask;
+	u32 phy_ignore_ta_mask;
+	int irqs[PHY_MAX_ADDR];
+	/* reset callback */
+	int (*reset)(struct mii_bus *bus);
+};
+
+#endif /* __LINUX_MDIO_GPIO_H */
diff --git a/kernel/include/linux/platform_data/mmc-esdhc-imx.h b/kernel/include/linux/platform_data/mmc-esdhc-imx.h
index 75f70f6ac..95ccab3f4 100644
--- a/kernel/include/linux/platform_data/mmc-esdhc-imx.h
+++ b/kernel/include/linux/platform_data/mmc-esdhc-imx.h
@@ -43,8 +43,8 @@ struct esdhc_platform_data {
 	enum wp_types wp_type;
 	enum cd_types cd_type;
 	int max_bus_width;
-	unsigned int f_max;
 	bool support_vsel;
 	unsigned int delay_line;
+	unsigned int tuning_step;       /* The delay cell steps in tuning procedure */
 };
 #endif /* __ASM_ARCH_IMX_ESDHC_H */
diff --git a/kernel/include/linux/platform_data/mtd-nand-pxa3xx.h b/kernel/include/linux/platform_data/mtd-nand-pxa3xx.h
index ac4ea2e64..394d15597 100644
--- a/kernel/include/linux/platform_data/mtd-nand-pxa3xx.h
+++ b/kernel/include/linux/platform_data/mtd-nand-pxa3xx.h
@@ -4,30 +4,6 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 
-struct pxa3xx_nand_timing {
-	unsigned int	tCH;  /* Enable signal hold time */
-	unsigned int	tCS;  /* Enable signal setup time */
-	unsigned int	tWH;  /* ND_nWE high duration */
-	unsigned int	tWP;  /* ND_nWE pulse time */
-	unsigned int	tRH;  /* ND_nRE high duration */
-	unsigned int	tRP;  /* ND_nRE pulse width */
-	unsigned int	tR;   /* ND_nWE high to ND_nRE low for read */
-	unsigned int	tWHR; /* ND_nWE high to ND_nRE low for status read */
-	unsigned int	tAR;  /* ND_ALE low to ND_nRE low delay */
-};
-
-struct pxa3xx_nand_flash {
-	char		*name;
-	uint32_t	chip_id;
-	unsigned int	page_per_block; /* Pages per block (PG_PER_BLK) */
-	unsigned int	page_size;	/* Page size in bytes (PAGE_SZ) */
-	unsigned int	flash_width;	/* Width of Flash memory (DWIDTH_M) */
-	unsigned int	dfc_width;	/* Width of flash controller(DWIDTH_C) */
-	unsigned int	num_blocks;	/* Number of physical blocks in Flash */
-
-	struct pxa3xx_nand_timing *timing;	/* NAND Flash timing */
-};
-
 /*
  * Current pxa3xx_nand controller has two chip select which
  * both be workable.
@@ -63,9 +39,6 @@ struct pxa3xx_nand_platform_data {
 
 	const struct mtd_partition		*parts[NUM_CHIP_SELECT];
 	unsigned int				nr_parts[NUM_CHIP_SELECT];
-
-	const struct pxa3xx_nand_flash * 	flash;
-	size_t					num_flash;
 };
 
 extern void pxa3xx_set_nand_info(struct pxa3xx_nand_platform_data *info);
diff --git a/kernel/include/linux/platform_data/nfcmrvl.h b/kernel/include/linux/platform_data/nfcmrvl.h
new file mode 100644
index 000000000..a6f9d633f
--- /dev/null
+++ b/kernel/include/linux/platform_data/nfcmrvl.h
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2015, Marvell International Ltd.
+ *
+ * This software file (the "File") is distributed by Marvell International
+ * Ltd. under the terms of the GNU General Public License Version 2, June 1991
+ * (the "License").  You may use, redistribute and/or modify this File in
+ * accordance with the terms and conditions of the License, a copy of which
+ * is available on the worldwide web at
+ * http://www.gnu.org/licenses/old-licenses/gpl-2.0.txt.
+ *
+ * THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
+ * ARE EXPRESSLY DISCLAIMED.  The License provides additional details about
+ * this warranty disclaimer.
+ */
+
+#ifndef _NFCMRVL_PTF_H_
+#define _NFCMRVL_PTF_H_
+
+struct nfcmrvl_platform_data {
+	/*
+	 * Generic
+	 */
+
+	/* GPIO that is wired to RESET_N signal */
+	unsigned int reset_n_io;
+	/* Tell if transport is muxed in HCI one */
+	unsigned int hci_muxed;
+
+	/*
+	 * UART specific
+	 */
+
+	/* Tell if UART needs flow control at init */
+	unsigned int flow_control;
+	/* Tell if firmware supports break control for power management */
+	unsigned int break_control;
+
+
+	/*
+	 * I2C specific
+	 */
+
+	unsigned int irq;
+	unsigned int irq_polarity;
+};
+
+#endif /* _NFCMRVL_PTF_H_ */
diff --git a/kernel/include/linux/platform_data/ntc_thermistor.h b/kernel/include/linux/platform_data/ntc_thermistor.h
index 0a6de4ca4..aed170588 100644
--- a/kernel/include/linux/platform_data/ntc_thermistor.h
+++ b/kernel/include/linux/platform_data/ntc_thermistor.h
@@ -27,6 +27,7 @@ enum ntc_thermistor_type {
 	TYPE_NCPXXWB473,
 	TYPE_NCPXXWL333,
 	TYPE_B57330V2103,
+	TYPE_NCPXXWF104,
 };
 
 struct ntc_thermistor_platform_data {
diff --git a/kernel/include/linux/platform_data/pixcir_i2c_ts.h b/kernel/include/linux/platform_data/pixcir_i2c_ts.h
new file mode 100644
index 000000000..646af6f8b
--- /dev/null
+++ b/kernel/include/linux/platform_data/pixcir_i2c_ts.h
@@ -0,0 +1,63 @@
+#ifndef	_PIXCIR_I2C_TS_H
+#define	_PIXCIR_I2C_TS_H
+
+/*
+ * Register map
+ */
+#define PIXCIR_REG_POWER_MODE	51
+#define PIXCIR_REG_INT_MODE	52
+
+/*
+ * Power modes:
+ * active: max scan speed
+ * idle: lower scan speed with automatic transition to active on touch
+ * halt: datasheet says sleep but this is more like halt as the chip
+ *       clocks are cut and it can only be brought out of this mode
+ *	 using the RESET pin.
+ */
+enum pixcir_power_mode {
+	PIXCIR_POWER_ACTIVE,
+	PIXCIR_POWER_IDLE,
+	PIXCIR_POWER_HALT,
+};
+
+#define PIXCIR_POWER_MODE_MASK	0x03
+#define PIXCIR_POWER_ALLOW_IDLE (1UL << 2)
+
+/*
+ * Interrupt modes:
+ * periodical: interrupt is asserted periodicaly
+ * diff coordinates: interrupt is asserted when coordinates change
+ * level on touch: interrupt level asserted during touch
+ * pulse on touch: interrupt pulse asserted druing touch
+ *
+ */
+enum pixcir_int_mode {
+	PIXCIR_INT_PERIODICAL,
+	PIXCIR_INT_DIFF_COORD,
+	PIXCIR_INT_LEVEL_TOUCH,
+	PIXCIR_INT_PULSE_TOUCH,
+};
+
+#define PIXCIR_INT_MODE_MASK	0x03
+#define PIXCIR_INT_ENABLE	(1UL << 3)
+#define PIXCIR_INT_POL_HIGH	(1UL << 2)
+
+/**
+ * struct pixcir_irc_chip_data - chip related data
+ * @max_fingers:	Max number of fingers reported simultaneously by h/w
+ * @has_hw_ids:		Hardware supports finger tracking IDs
+ *
+ */
+struct pixcir_i2c_chip_data {
+	u8 max_fingers;
+	bool has_hw_ids;
+};
+
+struct pixcir_ts_platform_data {
+	int x_max;
+	int y_max;
+	struct pixcir_i2c_chip_data chip;
+};
+
+#endif
diff --git a/kernel/include/linux/platform_data/s3c-hsotg.h b/kernel/include/linux/platform_data/s3c-hsotg.h
index 3f1cbf95e..3982586ba 100644
--- a/kernel/include/linux/platform_data/s3c-hsotg.h
+++ b/kernel/include/linux/platform_data/s3c-hsotg.h
@@ -17,19 +17,19 @@
 
 struct platform_device;
 
-enum s3c_hsotg_dmamode {
+enum dwc2_hsotg_dmamode {
 	S3C_HSOTG_DMA_NONE,	/* do not use DMA at-all */
 	S3C_HSOTG_DMA_ONLY,	/* always use DMA */
 	S3C_HSOTG_DMA_DRV,	/* DMA is chosen by driver */
 };
 
 /**
- * struct s3c_hsotg_plat - platform data for high-speed otg/udc
+ * struct dwc2_hsotg_plat - platform data for high-speed otg/udc
  * @dma: Whether to use DMA or not.
  * @is_osc: The clock source is an oscillator, not a crystal
  */
-struct s3c_hsotg_plat {
-	enum s3c_hsotg_dmamode	dma;
+struct dwc2_hsotg_plat {
+	enum dwc2_hsotg_dmamode	dma;
 	unsigned int		is_osc:1;
 	int                     phy_type;
 
@@ -37,6 +37,6 @@ struct s3c_hsotg_plat {
 	int (*phy_exit)(struct platform_device *pdev, int type);
 };
 
-extern void s3c_hsotg_set_platdata(struct s3c_hsotg_plat *pd);
+extern void dwc2_hsotg_set_platdata(struct dwc2_hsotg_plat *pd);
 
 #endif /* __LINUX_USB_S3C_HSOTG_H */
diff --git a/kernel/include/linux/platform_data/spi-davinci.h b/kernel/include/linux/platform_data/spi-davinci.h
index 8dc2fa47a..f4edcb03c 100644
--- a/kernel/include/linux/platform_data/spi-davinci.h
+++ b/kernel/include/linux/platform_data/spi-davinci.h
@@ -49,6 +49,7 @@ struct davinci_spi_platform_data {
 	u8			num_chipselect;
 	u8			intr_line;
 	u8			*chip_sel;
+	u8			prescaler_limit;
 	bool			cshold_bug;
 	enum dma_event_q	dma_event_q;
 };
diff --git a/kernel/include/linux/platform_data/spi-mt65xx.h b/kernel/include/linux/platform_data/spi-mt65xx.h
new file mode 100644
index 000000000..54b044839
--- /dev/null
+++ b/kernel/include/linux/platform_data/spi-mt65xx.h
@@ -0,0 +1,20 @@
+/*
+ *  MTK SPI bus driver definitions
+ *
+ * Copyright (c) 2015 MediaTek Inc.
+ * Author: Leilk Liu <leilk.liu@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ____LINUX_PLATFORM_DATA_SPI_MTK_H
+#define ____LINUX_PLATFORM_DATA_SPI_MTK_H
+
+/* Board specific platform_data */
+struct mtk_chip_config {
+	u32 tx_mlsb;
+	u32 rx_mlsb;
+};
+#endif
diff --git a/kernel/include/linux/platform_data/st21nfcb.h b/kernel/include/linux/platform_data/st-nci.h
index b023373d9..f6494b347 100644
--- a/kernel/include/linux/platform_data/st21nfcb.h
+++ b/kernel/include/linux/platform_data/st-nci.h
@@ -1,7 +1,7 @@
 /*
- * Driver include for the ST21NFCB NFC chip.
+ * Driver include for ST NCI NFC chip family.
  *
- * Copyright (C) 2014  STMicroelectronics SAS. All rights reserved.
+ * Copyright (C) 2014-2015  STMicroelectronics SAS. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -16,14 +16,16 @@
  * along with this program; if not, see <http://www.gnu.org/licenses/>.
  */
 
-#ifndef _ST21NFCB_NCI_H_
-#define _ST21NFCB_NCI_H_
+#ifndef _ST_NCI_H_
+#define _ST_NCI_H_
 
-#define ST21NFCB_NCI_DRIVER_NAME "st21nfcb_nci"
+#define ST_NCI_DRIVER_NAME "st_nci"
 
-struct st21nfcb_nfc_platform_data {
+struct st_nci_nfc_platform_data {
 	unsigned int gpio_reset;
 	unsigned int irq_polarity;
+	bool is_ese_present;
+	bool is_uicc_present;
 };
 
-#endif /* _ST21NFCB_NCI_H_ */
+#endif /* _ST_NCI_H_ */
diff --git a/kernel/include/linux/platform_data/usb-rcar-gen2-phy.h b/kernel/include/linux/platform_data/usb-rcar-gen2-phy.h
deleted file mode 100644
index dd3ba46c0..000000000
--- a/kernel/include/linux/platform_data/usb-rcar-gen2-phy.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * Copyright (C) 2013 Renesas Solutions Corp.
- * Copyright (C) 2013 Cogent Embedded, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __USB_RCAR_GEN2_PHY_H
-#define __USB_RCAR_GEN2_PHY_H
-
-#include <linux/types.h>
-
-struct rcar_gen2_phy_platform_data {
-	/* USB channel 0 configuration */
-	bool chan0_pci:1;	/* true: PCI USB host 0, false: USBHS */
-	/* USB channel 2 configuration */
-	bool chan2_pci:1;	/* true: PCI USB host 2, false: USBSS */
-};
-
-#endif
diff --git a/kernel/include/linux/platform_data/video-ep93xx.h b/kernel/include/linux/platform_data/video-ep93xx.h
index 92fc2b223..699ac4109 100644
--- a/kernel/include/linux/platform_data/video-ep93xx.h
+++ b/kernel/include/linux/platform_data/video-ep93xx.h
@@ -2,11 +2,8 @@
 #define __VIDEO_EP93XX_H
 
 struct platform_device;
-struct fb_videomode;
 struct fb_info;
 
-#define EP93XXFB_USE_MODEDB		0
-
 /* VideoAttributes flags */
 #define EP93XXFB_STATE_MACHINE_ENABLE	(1 << 0)
 #define EP93XXFB_PIXEL_CLOCK_ENABLE	(1 << 1)
@@ -38,12 +35,7 @@ struct fb_info;
 					 EP93XXFB_PIXEL_DATA_ENABLE)
 
 struct ep93xxfb_mach_info {
-	unsigned int			num_modes;
-	const struct fb_videomode	*modes;
-	const struct fb_videomode	*default_mode;
-	int				bpp;
 	unsigned int			flags;
-
 	int	(*setup)(struct platform_device *pdev);
 	void	(*teardown)(struct platform_device *pdev);
 	void	(*blank)(int blank_mode, struct fb_info *info);
diff --git a/kernel/include/linux/platform_data/video-msm_fb.h b/kernel/include/linux/platform_data/video-msm_fb.h
deleted file mode 100644
index 31449be3e..000000000
--- a/kernel/include/linux/platform_data/video-msm_fb.h
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * Internal shared definitions for various MSM framebuffer parts.
- *
- * Copyright (C) 2007 Google Incorporated
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef _MSM_FB_H_
-#define _MSM_FB_H_
-
-#include <linux/device.h>
-
-struct mddi_info;
-
-struct msm_fb_data {
-	int xres;	/* x resolution in pixels */
-	int yres;	/* y resolution in pixels */
-	int width;	/* disply width in mm */
-	int height;	/* display height in mm */
-	unsigned output_format;
-};
-
-struct msmfb_callback {
-	void (*func)(struct msmfb_callback *);
-};
-
-enum {
-	MSM_MDDI_PMDH_INTERFACE,
-	MSM_MDDI_EMDH_INTERFACE,
-	MSM_EBI2_INTERFACE,
-};
-
-#define MSMFB_CAP_PARTIAL_UPDATES	(1 << 0)
-
-struct msm_panel_data {
-	/* turns off the fb memory */
-	int (*suspend)(struct msm_panel_data *);
-	/* turns on the fb memory */
-	int (*resume)(struct msm_panel_data *);
-	/* turns off the panel */
-	int (*blank)(struct msm_panel_data *);
-	/* turns on the panel */
-	int (*unblank)(struct msm_panel_data *);
-	void (*wait_vsync)(struct msm_panel_data *);
-	void (*request_vsync)(struct msm_panel_data *, struct msmfb_callback *);
-	void (*clear_vsync)(struct msm_panel_data *);
-	/* from the enum above */
-	unsigned interface_type;
-	/* data to be passed to the fb driver */
-	struct msm_fb_data *fb_data;
-
-	/* capabilities supported by the panel */
-	uint32_t caps;
-};
-
-struct msm_mddi_client_data {
-	void (*suspend)(struct msm_mddi_client_data *);
-	void (*resume)(struct msm_mddi_client_data *);
-	void (*activate_link)(struct msm_mddi_client_data *);
-	void (*remote_write)(struct msm_mddi_client_data *, uint32_t val,
-			     uint32_t reg);
-	uint32_t (*remote_read)(struct msm_mddi_client_data *, uint32_t reg);
-	void (*auto_hibernate)(struct msm_mddi_client_data *, int);
-	/* custom data that needs to be passed from the board file to a 
-	 * particular client */
-	void *private_client_data;
-	struct resource *fb_resource;
-	/* from the list above */
-	unsigned interface_type;
-};
-
-struct msm_mddi_platform_data {
-	unsigned int clk_rate;
-	void (*power_client)(struct msm_mddi_client_data *, int on);
-
-	/* fixup the mfr name, product id */
-	void (*fixup)(uint16_t *mfr_name, uint16_t *product_id);
-
-	struct resource *fb_resource; /*optional*/
-	/* number of clients in the list that follows */
-	int num_clients;
-	/* array of client information of clients */
-	struct {
-		unsigned product_id; /* mfr id in top 16 bits, product id
-				      * in lower 16 bits
-				      */
-		char *name;	/* the device name will be the platform
-				 * device name registered for the client,
-				 * it should match the name of the associated
-				 * driver
-				 */
-		unsigned id;	/* id for mddi client device node, will also
-				 * be used as device id of panel devices, if
-				 * the client device will have multiple panels
-				 * space must be left here for them
-				 */
-		void *client_data;	/* required private client data */
-		unsigned int clk_rate;	/* optional: if the client requires a
-					* different mddi clk rate
-					*/
-	} client_platform_data[];
-};
-
-struct mdp_blit_req;
-struct fb_info;
-struct mdp_device {
-	struct device dev;
-	void (*dma)(struct mdp_device *mpd, uint32_t addr,
-		    uint32_t stride, uint32_t w, uint32_t h, uint32_t x,
-		    uint32_t y, struct msmfb_callback *callback, int interface);
-	void (*dma_wait)(struct mdp_device *mdp);
-	int (*blit)(struct mdp_device *mdp, struct fb_info *fb,
-		    struct mdp_blit_req *req);
-	void (*set_grp_disp)(struct mdp_device *mdp, uint32_t disp_id);
-};
-
-struct class_interface;
-int register_mdp_client(struct class_interface *class_intf);
-
-/**** private client data structs go below this line ***/
-
-struct msm_mddi_bridge_platform_data {
-	/* from board file */
-	int (*init)(struct msm_mddi_bridge_platform_data *,
-		    struct msm_mddi_client_data *);
-	int (*uninit)(struct msm_mddi_bridge_platform_data *,
-		      struct msm_mddi_client_data *);
-	/* passed to panel for use by the fb driver */
-	int (*blank)(struct msm_mddi_bridge_platform_data *,
-		     struct msm_mddi_client_data *);
-	int (*unblank)(struct msm_mddi_bridge_platform_data *,
-		       struct msm_mddi_client_data *);
-	struct msm_fb_data fb_data;
-};
-
-
-
-#endif
diff --git a/kernel/include/linux/platform_data/wkup_m3.h b/kernel/include/linux/platform_data/wkup_m3.h
new file mode 100644
index 000000000..3f1d77eff
--- /dev/null
+++ b/kernel/include/linux/platform_data/wkup_m3.h
@@ -0,0 +1,30 @@
+/*
+ * TI Wakeup M3 remote processor platform data
+ *
+ * Copyright (C) 2014-2015 Texas Instruments, Inc.
+ *
+ * Dave Gerlach <d-gerlach@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _LINUX_PLATFORM_DATA_WKUP_M3_H
+#define _LINUX_PLATFORM_DATA_WKUP_M3_H
+
+struct platform_device;
+
+struct wkup_m3_platform_data {
+	const char *reset_name;
+
+	int (*assert_reset)(struct platform_device *pdev, const char *name);
+	int (*deassert_reset)(struct platform_device *pdev, const char *name);
+};
+
+#endif /* _LINUX_PLATFORM_DATA_WKUP_M3_H */
diff --git a/kernel/include/linux/platform_data/zforce_ts.h b/kernel/include/linux/platform_data/zforce_ts.h
index 0472ab2f6..7bdece8ef 100644
--- a/kernel/include/linux/platform_data/zforce_ts.h
+++ b/kernel/include/linux/platform_data/zforce_ts.h
@@ -16,9 +16,6 @@
 #define _LINUX_INPUT_ZFORCE_TS_H
 
 struct zforce_ts_platdata {
-	int gpio_int;
-	int gpio_rst;
-
 	unsigned int x_max;
 	unsigned int y_max;
 };