These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 185 insertions, 17 deletions

diff --git a/kernel/drivers/usb/phy/phy-msm-usb.c b/kernel/drivers/usb/phy/phy-msm-usb.c
index c9156beea..970a30e15 100644
--- a/kernel/drivers/usb/phy/phy-msm-usb.c
+++ b/kernel/drivers/usb/phy/phy-msm-usb.c
@@ -18,6 +18,7 @@
 
 #include <linux/module.h>
 #include <linux/device.h>
+#include <linux/gpio/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/slab.h>
@@ -32,6 +33,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/reboot.h>
 #include <linux/reset.h>
 
 #include <linux/usb.h>
@@ -240,8 +242,14 @@ static void ulpi_init(struct msm_otg *motg)
 static int msm_phy_notify_disconnect(struct usb_phy *phy,
 				   enum usb_device_speed speed)
 {
+	struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
 	int val;
 
+	if (motg->manual_pullup) {
+		val = ULPI_MISC_A_VBUSVLDEXT | ULPI_MISC_A_VBUSVLDEXTSEL;
+		usb_phy_io_write(phy, val, ULPI_CLR(ULPI_MISC_A));
+	}
+
 	/*
 	 * Put the transceiver in non-driving mode. Otherwise host
 	 * may not detect soft-disconnection.
@@ -422,6 +430,24 @@ static int msm_phy_init(struct usb_phy *phy)
 		ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_FALL);
 	}
 
+	if (motg->manual_pullup) {
+		val = ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT;
+		ulpi_write(phy, val, ULPI_SET(ULPI_MISC_A));
+
+		val = readl(USB_GENCONFIG_2);
+		val |= GENCONFIG_2_SESS_VLD_CTRL_EN;
+		writel(val, USB_GENCONFIG_2);
+
+		val = readl(USB_USBCMD);
+		val |= USBCMD_SESS_VLD_CTRL;
+		writel(val, USB_USBCMD);
+
+		val = ulpi_read(phy, ULPI_FUNC_CTRL);
+		val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
+		val |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
+		ulpi_write(phy, val, ULPI_FUNC_CTRL);
+	}
+
 	if (motg->phy_number)
 		writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
 
@@ -1436,10 +1462,50 @@ static const struct of_device_id msm_otg_dt_match[] = {
 };
 MODULE_DEVICE_TABLE(of, msm_otg_dt_match);
 
+static int msm_otg_vbus_notifier(struct notifier_block *nb, unsigned long event,
+				void *ptr)
+{
+	struct msm_usb_cable *vbus = container_of(nb, struct msm_usb_cable, nb);
+	struct msm_otg *motg = container_of(vbus, struct msm_otg, vbus);
+
+	if (event)
+		set_bit(B_SESS_VLD, &motg->inputs);
+	else
+		clear_bit(B_SESS_VLD, &motg->inputs);
+
+	if (test_bit(B_SESS_VLD, &motg->inputs)) {
+		/* Switch D+/D- lines to Device connector */
+		gpiod_set_value_cansleep(motg->switch_gpio, 0);
+	} else {
+		/* Switch D+/D- lines to Hub */
+		gpiod_set_value_cansleep(motg->switch_gpio, 1);
+	}
+
+	schedule_work(&motg->sm_work);
+
+	return NOTIFY_DONE;
+}
+
+static int msm_otg_id_notifier(struct notifier_block *nb, unsigned long event,
+				void *ptr)
+{
+	struct msm_usb_cable *id = container_of(nb, struct msm_usb_cable, nb);
+	struct msm_otg *motg = container_of(id, struct msm_otg, id);
+
+	if (event)
+		clear_bit(ID, &motg->inputs);
+	else
+		set_bit(ID, &motg->inputs);
+
+	schedule_work(&motg->sm_work);
+
+	return NOTIFY_DONE;
+}
+
 static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
 {
 	struct msm_otg_platform_data *pdata;
-	const struct of_device_id *id;
+	struct extcon_dev *ext_id, *ext_vbus;
 	struct device_node *node = pdev->dev.of_node;
 	struct property *prop;
 	int len, ret, words;
@@ -1451,8 +1517,9 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
 
 	motg->pdata = pdata;
 
-	id = of_match_device(msm_otg_dt_match, &pdev->dev);
-	pdata->phy_type = (enum msm_usb_phy_type) id->data;
+	pdata->phy_type = (enum msm_usb_phy_type)of_device_get_match_data(&pdev->dev);
+	if (!pdata->phy_type)
+		return 1;
 
 	motg->link_rst = devm_reset_control_get(&pdev->dev, "link");
 	if (IS_ERR(motg->link_rst))
@@ -1462,7 +1529,7 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
 	if (IS_ERR(motg->phy_rst))
 		motg->phy_rst = NULL;
 
-	pdata->mode = of_usb_get_dr_mode(node);
+	pdata->mode = usb_get_dr_mode(&pdev->dev);
 	if (pdata->mode == USB_DR_MODE_UNKNOWN)
 		pdata->mode = USB_DR_MODE_OTG;
 
@@ -1487,6 +1554,63 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
 		motg->vdd_levels[VDD_LEVEL_MAX] = tmp[VDD_LEVEL_MAX];
 	}
 
+	motg->manual_pullup = of_property_read_bool(node, "qcom,manual-pullup");
+
+	motg->switch_gpio = devm_gpiod_get_optional(&pdev->dev, "switch",
+						    GPIOD_OUT_LOW);
+	if (IS_ERR(motg->switch_gpio))
+		return PTR_ERR(motg->switch_gpio);
+
+	ext_id = ERR_PTR(-ENODEV);
+	ext_vbus = ERR_PTR(-ENODEV);
+	if (of_property_read_bool(node, "extcon")) {
+
+		/* Each one of them is not mandatory */
+		ext_vbus = extcon_get_edev_by_phandle(&pdev->dev, 0);
+		if (IS_ERR(ext_vbus) && PTR_ERR(ext_vbus) != -ENODEV)
+			return PTR_ERR(ext_vbus);
+
+		ext_id = extcon_get_edev_by_phandle(&pdev->dev, 1);
+		if (IS_ERR(ext_id) && PTR_ERR(ext_id) != -ENODEV)
+			return PTR_ERR(ext_id);
+	}
+
+	if (!IS_ERR(ext_vbus)) {
+		motg->vbus.extcon = ext_vbus;
+		motg->vbus.nb.notifier_call = msm_otg_vbus_notifier;
+		ret = extcon_register_notifier(ext_vbus, EXTCON_USB,
+						&motg->vbus.nb);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "register VBUS notifier failed\n");
+			return ret;
+		}
+
+		ret = extcon_get_cable_state_(ext_vbus, EXTCON_USB);
+		if (ret)
+			set_bit(B_SESS_VLD, &motg->inputs);
+		else
+			clear_bit(B_SESS_VLD, &motg->inputs);
+	}
+
+	if (!IS_ERR(ext_id)) {
+		motg->id.extcon = ext_id;
+		motg->id.nb.notifier_call = msm_otg_id_notifier;
+		ret = extcon_register_notifier(ext_id, EXTCON_USB_HOST,
+						&motg->id.nb);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "register ID notifier failed\n");
+			extcon_unregister_notifier(motg->vbus.extcon,
+						   EXTCON_USB, &motg->vbus.nb);
+			return ret;
+		}
+
+		ret = extcon_get_cable_state_(ext_id, EXTCON_USB_HOST);
+		if (ret)
+			clear_bit(ID, &motg->inputs);
+		else
+			set_bit(ID, &motg->inputs);
+	}
+
 	prop = of_find_property(node, "qcom,phy-init-sequence", &len);
 	if (!prop || !len)
 		return 0;
@@ -1510,6 +1634,19 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
 	return 0;
 }
 
+static int msm_otg_reboot_notify(struct notifier_block *this,
+				 unsigned long code, void *unused)
+{
+	struct msm_otg *motg = container_of(this, struct msm_otg, reboot);
+
+	/*
+	 * Ensure that D+/D- lines are routed to uB connector, so
+	 * we could load bootloader/kernel at next reboot
+	 */
+	gpiod_set_value_cansleep(motg->switch_gpio, 0);
+	return NOTIFY_DONE;
+}
+
 static int msm_otg_probe(struct platform_device *pdev)
 {
 	struct regulator_bulk_data regs[3];
@@ -1525,15 +1662,6 @@ static int msm_otg_probe(struct platform_device *pdev)
 	if (!motg)
 		return -ENOMEM;
 
-	pdata = dev_get_platdata(&pdev->dev);
-	if (!pdata) {
-		if (!np)
-			return -ENXIO;
-		ret = msm_otg_read_dt(pdev, motg);
-		if (ret)
-			return ret;
-	}
-
 	motg->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
 				     GFP_KERNEL);
 	if (!motg->phy.otg)
@@ -1575,6 +1703,15 @@ static int msm_otg_probe(struct platform_device *pdev)
 	if (!motg->regs)
 		return -ENOMEM;
 
+	pdata = dev_get_platdata(&pdev->dev);
+	if (!pdata) {
+		if (!np)
+			return -ENXIO;
+		ret = msm_otg_read_dt(pdev, motg);
+		if (ret)
+			return ret;
+	}
+
 	/*
 	 * NOTE: The PHYs can be multiplexed between the chipidea controller
 	 * and the dwc3 controller, using a single bit. It is important that
@@ -1582,8 +1719,10 @@ static int msm_otg_probe(struct platform_device *pdev)
 	 */
 	if (motg->phy_number) {
 		phy_select = devm_ioremap_nocache(&pdev->dev, USB2_PHY_SEL, 4);
-		if (!phy_select)
-			return -ENOMEM;
+		if (!phy_select) {
+			ret = -ENOMEM;
+			goto unregister_extcon;
+		}
 		/* Enable second PHY with the OTG port */
 		writel(0x1, phy_select);
 	}
@@ -1593,7 +1732,8 @@ static int msm_otg_probe(struct platform_device *pdev)
 	motg->irq = platform_get_irq(pdev, 0);
 	if (motg->irq < 0) {
 		dev_err(&pdev->dev, "platform_get_irq failed\n");
-		return motg->irq;
+		ret = motg->irq;
+		goto unregister_extcon;
 	}
 
 	regs[0].supply = "vddcx";
@@ -1602,7 +1742,7 @@ static int msm_otg_probe(struct platform_device *pdev)
 
 	ret = devm_regulator_bulk_get(motg->phy.dev, ARRAY_SIZE(regs), regs);
 	if (ret)
-		return ret;
+		goto unregister_extcon;
 
 	motg->vddcx = regs[0].consumer;
 	motg->v3p3  = regs[1].consumer;
@@ -1674,6 +1814,17 @@ static int msm_otg_probe(struct platform_device *pdev)
 			dev_dbg(&pdev->dev, "Can not create mode change file\n");
 	}
 
+	if (test_bit(B_SESS_VLD, &motg->inputs)) {
+		/* Switch D+/D- lines to Device connector */
+		gpiod_set_value_cansleep(motg->switch_gpio, 0);
+	} else {
+		/* Switch D+/D- lines to Hub */
+		gpiod_set_value_cansleep(motg->switch_gpio, 1);
+	}
+
+	motg->reboot.notifier_call = msm_otg_reboot_notify;
+	register_reboot_notifier(&motg->reboot);
+
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
@@ -1688,6 +1839,12 @@ disable_clks:
 	clk_disable_unprepare(motg->clk);
 	if (!IS_ERR(motg->core_clk))
 		clk_disable_unprepare(motg->core_clk);
+unregister_extcon:
+	extcon_unregister_notifier(motg->id.extcon,
+				   EXTCON_USB_HOST, &motg->id.nb);
+	extcon_unregister_notifier(motg->vbus.extcon,
+				   EXTCON_USB, &motg->vbus.nb);
+
 	return ret;
 }
 
@@ -1700,6 +1857,17 @@ static int msm_otg_remove(struct platform_device *pdev)
 	if (phy->otg->host || phy->otg->gadget)
 		return -EBUSY;
 
+	unregister_reboot_notifier(&motg->reboot);
+
+	/*
+	 * Ensure that D+/D- lines are routed to uB connector, so
+	 * we could load bootloader/kernel at next reboot
+	 */
+	gpiod_set_value_cansleep(motg->switch_gpio, 0);
+
+	extcon_unregister_notifier(motg->id.extcon, EXTCON_USB_HOST, &motg->id.nb);
+	extcon_unregister_notifier(motg->vbus.extcon, EXTCON_USB, &motg->vbus.nb);
+
 	msm_otg_debugfs_cleanup();
 	cancel_delayed_work_sync(&motg->chg_work);
 	cancel_work_sync(&motg->sm_work);