These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

17 files changed, 4860 insertions, 3514 deletions

diff --git a/kernel/drivers/tty/serial/8250/8250.h b/kernel/drivers/tty/serial/8250/8250.h
index c43f74c53..d54dcd87c 100644
--- a/kernel/drivers/tty/serial/8250/8250.h
+++ b/kernel/drivers/tty/serial/8250/8250.h
@@ -42,9 +42,9 @@ struct uart_8250_dma {
 	size_t			rx_size;
 	size_t			tx_size;
 
-	unsigned char		tx_running:1;
-	unsigned char		tx_err: 1;
-	unsigned char		rx_running:1;
+	unsigned char		tx_running;
+	unsigned char		tx_err;
+	unsigned char		rx_running;
 };
 
 struct old_serial_port {
@@ -211,3 +211,14 @@ static inline int ns16550a_goto_highspeed(struct uart_8250_port *up)
 	}
 	return 1;
 }
+
+static inline int serial_index(struct uart_port *port)
+{
+	return port->minor - 64;
+}
+
+#if 0
+#define DEBUG_INTR(fmt...)	printk(fmt)
+#else
+#define DEBUG_INTR(fmt...)	do { } while (0)
+#endif
diff --git a/kernel/drivers/tty/serial/8250/8250_core.c b/kernel/drivers/tty/serial/8250/8250_core.c
index 822a2e197..af7701ca4 100644
--- a/kernel/drivers/tty/serial/8250/8250_core.c
+++ b/kernel/drivers/tty/serial/8250/8250_core.c
@@ -1,25 +1,23 @@
 /*
- *  Driver for 8250/16550-type serial ports
+ *  Universal/legacy driver for 8250/16550-type serial ports
  *
  *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
  *
  *  Copyright (C) 2001 Russell King.
  *
+ *  Supports: ISA-compatible 8250/16550 ports
+ *	      PNP 8250/16550 ports
+ *	      early_serial_setup() ports
+ *	      userspace-configurable "phantom" ports
+ *	      "serial8250" platform devices
+ *	      serial8250_register_8250_port() ports
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
- *
- * A note about mapbase / membase
- *
- *  mapbase is the physical address of the IO port.
- *  membase is an 'ioremapped' cookie.
  */
 
-#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/ioport.h>
@@ -36,14 +34,13 @@
 #include <linux/nmi.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
-#include <linux/kdb.h>
 #include <linux/uaccess.h>
 #include <linux/pm_runtime.h>
+#include <linux/io.h>
 #ifdef CONFIG_SPARC
 #include <linux/sunserialcore.h>
 #endif
 
-#include <asm/io.h>
 #include <asm/irq.h>
 
 #include "8250.h"
@@ -59,29 +56,9 @@ static unsigned int nr_uarts = CONFIG_SERIAL_8250_RUNTIME_UARTS;
 
 static struct uart_driver serial8250_reg;
 
-static int serial_index(struct uart_port *port)
-{
-	return port->minor - 64;
-}
-
 static unsigned int skip_txen_test; /* force skip of txen test at init time */
 
 /*
- * Debugging.
- */
-#if 0
-#define DEBUG_AUTOCONF(fmt...)	printk(fmt)
-#else
-#define DEBUG_AUTOCONF(fmt...)	do { } while (0)
-#endif
-
-#if 0
-#define DEBUG_INTR(fmt...)	printk(fmt)
-#else
-#define DEBUG_INTR(fmt...)	do { } while (0)
-#endif
-
-/*
  * On -rt we can have a more delays, and legitimately
  * so - so don't drop work spuriously and spam the
  * syslog:
@@ -92,22 +69,6 @@ static unsigned int skip_txen_test; /* force skip of txen test at init time */
 # define PASS_LIMIT	512
 #endif
 
-#define BOTH_EMPTY 	(UART_LSR_TEMT | UART_LSR_THRE)
-
-
-#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
-#define CONFIG_SERIAL_DETECT_IRQ 1
-#endif
-#ifdef CONFIG_SERIAL_8250_MANY_PORTS
-#define CONFIG_SERIAL_MANY_PORTS 1
-#endif
-
-/*
- * HUB6 is always on.  This will be removed once the header
- * files have been cleaned.
- */
-#define CONFIG_HUB6 1
-
 #include <asm/serial.h>
 /*
  * SERIAL_PORT_DFNS tells us about built-in ports that have no
@@ -143,1563 +104,6 @@ static struct hlist_head irq_lists[NR_IRQ_HASH];
 static DEFINE_MUTEX(hash_mutex);	/* Used to walk the hash */
 
 /*
- * Here we define the default xmit fifo size used for each type of UART.
- */
-static const struct serial8250_config uart_config[] = {
-	[PORT_UNKNOWN] = {
-		.name		= "unknown",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-	},
-	[PORT_8250] = {
-		.name		= "8250",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-	},
-	[PORT_16450] = {
-		.name		= "16450",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-	},
-	[PORT_16550] = {
-		.name		= "16550",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-	},
-	[PORT_16550A] = {
-		.name		= "16550A",
-		.fifo_size	= 16,
-		.tx_loadsz	= 16,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.rxtrig_bytes	= {1, 4, 8, 14},
-		.flags		= UART_CAP_FIFO,
-	},
-	[PORT_CIRRUS] = {
-		.name		= "Cirrus",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-	},
-	[PORT_16650] = {
-		.name		= "ST16650",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
-	},
-	[PORT_16650V2] = {
-		.name		= "ST16650V2",
-		.fifo_size	= 32,
-		.tx_loadsz	= 16,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
-				  UART_FCR_T_TRIG_00,
-		.rxtrig_bytes	= {8, 16, 24, 28},
-		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
-	},
-	[PORT_16750] = {
-		.name		= "TI16750",
-		.fifo_size	= 64,
-		.tx_loadsz	= 64,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
-				  UART_FCR7_64BYTE,
-		.rxtrig_bytes	= {1, 16, 32, 56},
-		.flags		= UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE,
-	},
-	[PORT_STARTECH] = {
-		.name		= "Startech",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1,
-	},
-	[PORT_16C950] = {
-		.name		= "16C950/954",
-		.fifo_size	= 128,
-		.tx_loadsz	= 128,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		/* UART_CAP_EFR breaks billionon CF bluetooth card. */
-		.flags		= UART_CAP_FIFO | UART_CAP_SLEEP,
-	},
-	[PORT_16654] = {
-		.name		= "ST16654",
-		.fifo_size	= 64,
-		.tx_loadsz	= 32,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
-				  UART_FCR_T_TRIG_10,
-		.rxtrig_bytes	= {8, 16, 56, 60},
-		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
-	},
-	[PORT_16850] = {
-		.name		= "XR16850",
-		.fifo_size	= 128,
-		.tx_loadsz	= 128,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
-	},
-	[PORT_RSA] = {
-		.name		= "RSA",
-		.fifo_size	= 2048,
-		.tx_loadsz	= 2048,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11,
-		.flags		= UART_CAP_FIFO,
-	},
-	[PORT_NS16550A] = {
-		.name		= "NS16550A",
-		.fifo_size	= 16,
-		.tx_loadsz	= 16,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_NATSEMI,
-	},
-	[PORT_XSCALE] = {
-		.name		= "XScale",
-		.fifo_size	= 32,
-		.tx_loadsz	= 32,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE,
-	},
-	[PORT_OCTEON] = {
-		.name		= "OCTEON",
-		.fifo_size	= 64,
-		.tx_loadsz	= 64,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO,
-	},
-	[PORT_AR7] = {
-		.name		= "AR7",
-		.fifo_size	= 16,
-		.tx_loadsz	= 16,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
-	},
-	[PORT_U6_16550A] = {
-		.name		= "U6_16550A",
-		.fifo_size	= 64,
-		.tx_loadsz	= 64,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
-	},
-	[PORT_TEGRA] = {
-		.name		= "Tegra",
-		.fifo_size	= 32,
-		.tx_loadsz	= 8,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
-				  UART_FCR_T_TRIG_01,
-		.rxtrig_bytes	= {1, 4, 8, 14},
-		.flags		= UART_CAP_FIFO | UART_CAP_RTOIE,
-	},
-	[PORT_XR17D15X] = {
-		.name		= "XR17D15X",
-		.fifo_size	= 64,
-		.tx_loadsz	= 64,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
-				  UART_CAP_SLEEP,
-	},
-	[PORT_XR17V35X] = {
-		.name		= "XR17V35X",
-		.fifo_size	= 256,
-		.tx_loadsz	= 256,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
-				  UART_FCR_T_TRIG_11,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
-				  UART_CAP_SLEEP,
-	},
-	[PORT_LPC3220] = {
-		.name		= "LPC3220",
-		.fifo_size	= 64,
-		.tx_loadsz	= 32,
-		.fcr		= UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
-				  UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00,
-		.flags		= UART_CAP_FIFO,
-	},
-	[PORT_BRCM_TRUMANAGE] = {
-		.name		= "TruManage",
-		.fifo_size	= 1,
-		.tx_loadsz	= 1024,
-		.flags		= UART_CAP_HFIFO,
-	},
-	[PORT_8250_CIR] = {
-		.name		= "CIR port"
-	},
-	[PORT_ALTR_16550_F32] = {
-		.name		= "Altera 16550 FIFO32",
-		.fifo_size	= 32,
-		.tx_loadsz	= 32,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
-	},
-	[PORT_ALTR_16550_F64] = {
-		.name		= "Altera 16550 FIFO64",
-		.fifo_size	= 64,
-		.tx_loadsz	= 64,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
-	},
-	[PORT_ALTR_16550_F128] = {
-		.name		= "Altera 16550 FIFO128",
-		.fifo_size	= 128,
-		.tx_loadsz	= 128,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
-		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
-	},
-/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
-workaround of errata A-008006 which states that tx_loadsz should  be
-configured less than Maximum supported fifo bytes */
-	[PORT_16550A_FSL64] = {
-		.name		= "16550A_FSL64",
-		.fifo_size	= 64,
-		.tx_loadsz	= 63,
-		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
-				  UART_FCR7_64BYTE,
-		.flags		= UART_CAP_FIFO,
-	},
-};
-
-/* Uart divisor latch read */
-static int default_serial_dl_read(struct uart_8250_port *up)
-{
-	return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8;
-}
-
-/* Uart divisor latch write */
-static void default_serial_dl_write(struct uart_8250_port *up, int value)
-{
-	serial_out(up, UART_DLL, value & 0xff);
-	serial_out(up, UART_DLM, value >> 8 & 0xff);
-}
-
-#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X)
-
-/* Au1x00/RT288x UART hardware has a weird register layout */
-static const s8 au_io_in_map[8] = {
-	 0,	/* UART_RX  */
-	 2,	/* UART_IER */
-	 3,	/* UART_IIR */
-	 5,	/* UART_LCR */
-	 6,	/* UART_MCR */
-	 7,	/* UART_LSR */
-	 8,	/* UART_MSR */
-	-1,	/* UART_SCR (unmapped) */
-};
-
-static const s8 au_io_out_map[8] = {
-	 1,	/* UART_TX  */
-	 2,	/* UART_IER */
-	 4,	/* UART_FCR */
-	 5,	/* UART_LCR */
-	 6,	/* UART_MCR */
-	-1,	/* UART_LSR (unmapped) */
-	-1,	/* UART_MSR (unmapped) */
-	-1,	/* UART_SCR (unmapped) */
-};
-
-static unsigned int au_serial_in(struct uart_port *p, int offset)
-{
-	if (offset >= ARRAY_SIZE(au_io_in_map))
-		return UINT_MAX;
-	offset = au_io_in_map[offset];
-	if (offset < 0)
-		return UINT_MAX;
-	return __raw_readl(p->membase + (offset << p->regshift));
-}
-
-static void au_serial_out(struct uart_port *p, int offset, int value)
-{
-	if (offset >= ARRAY_SIZE(au_io_out_map))
-		return;
-	offset = au_io_out_map[offset];
-	if (offset < 0)
-		return;
-	__raw_writel(value, p->membase + (offset << p->regshift));
-}
-
-/* Au1x00 haven't got a standard divisor latch */
-static int au_serial_dl_read(struct uart_8250_port *up)
-{
-	return __raw_readl(up->port.membase + 0x28);
-}
-
-static void au_serial_dl_write(struct uart_8250_port *up, int value)
-{
-	__raw_writel(value, up->port.membase + 0x28);
-}
-
-#endif
-
-static unsigned int hub6_serial_in(struct uart_port *p, int offset)
-{
-	offset = offset << p->regshift;
-	outb(p->hub6 - 1 + offset, p->iobase);
-	return inb(p->iobase + 1);
-}
-
-static void hub6_serial_out(struct uart_port *p, int offset, int value)
-{
-	offset = offset << p->regshift;
-	outb(p->hub6 - 1 + offset, p->iobase);
-	outb(value, p->iobase + 1);
-}
-
-static unsigned int mem_serial_in(struct uart_port *p, int offset)
-{
-	offset = offset << p->regshift;
-	return readb(p->membase + offset);
-}
-
-static void mem_serial_out(struct uart_port *p, int offset, int value)
-{
-	offset = offset << p->regshift;
-	writeb(value, p->membase + offset);
-}
-
-static void mem32_serial_out(struct uart_port *p, int offset, int value)
-{
-	offset = offset << p->regshift;
-	writel(value, p->membase + offset);
-}
-
-static unsigned int mem32_serial_in(struct uart_port *p, int offset)
-{
-	offset = offset << p->regshift;
-	return readl(p->membase + offset);
-}
-
-static void mem32be_serial_out(struct uart_port *p, int offset, int value)
-{
-	offset = offset << p->regshift;
-	iowrite32be(value, p->membase + offset);
-}
-
-static unsigned int mem32be_serial_in(struct uart_port *p, int offset)
-{
-	offset = offset << p->regshift;
-	return ioread32be(p->membase + offset);
-}
-
-static unsigned int io_serial_in(struct uart_port *p, int offset)
-{
-	offset = offset << p->regshift;
-	return inb(p->iobase + offset);
-}
-
-static void io_serial_out(struct uart_port *p, int offset, int value)
-{
-	offset = offset << p->regshift;
-	outb(value, p->iobase + offset);
-}
-
-static int serial8250_default_handle_irq(struct uart_port *port);
-static int exar_handle_irq(struct uart_port *port);
-
-static void set_io_from_upio(struct uart_port *p)
-{
-	struct uart_8250_port *up = up_to_u8250p(p);
-
-	up->dl_read = default_serial_dl_read;
-	up->dl_write = default_serial_dl_write;
-
-	switch (p->iotype) {
-	case UPIO_HUB6:
-		p->serial_in = hub6_serial_in;
-		p->serial_out = hub6_serial_out;
-		break;
-
-	case UPIO_MEM:
-		p->serial_in = mem_serial_in;
-		p->serial_out = mem_serial_out;
-		break;
-
-	case UPIO_MEM32:
-		p->serial_in = mem32_serial_in;
-		p->serial_out = mem32_serial_out;
-		break;
-
-	case UPIO_MEM32BE:
-		p->serial_in = mem32be_serial_in;
-		p->serial_out = mem32be_serial_out;
-		break;
-
-#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X)
-	case UPIO_AU:
-		p->serial_in = au_serial_in;
-		p->serial_out = au_serial_out;
-		up->dl_read = au_serial_dl_read;
-		up->dl_write = au_serial_dl_write;
-		break;
-#endif
-
-	default:
-		p->serial_in = io_serial_in;
-		p->serial_out = io_serial_out;
-		break;
-	}
-	/* Remember loaded iotype */
-	up->cur_iotype = p->iotype;
-	p->handle_irq = serial8250_default_handle_irq;
-}
-
-static void
-serial_port_out_sync(struct uart_port *p, int offset, int value)
-{
-	switch (p->iotype) {
-	case UPIO_MEM:
-	case UPIO_MEM32:
-	case UPIO_MEM32BE:
-	case UPIO_AU:
-		p->serial_out(p, offset, value);
-		p->serial_in(p, UART_LCR);	/* safe, no side-effects */
-		break;
-	default:
-		p->serial_out(p, offset, value);
-	}
-}
-
-/*
- * For the 16C950
- */
-static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
-{
-	serial_out(up, UART_SCR, offset);
-	serial_out(up, UART_ICR, value);
-}
-
-static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
-{
-	unsigned int value;
-
-	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
-	serial_out(up, UART_SCR, offset);
-	value = serial_in(up, UART_ICR);
-	serial_icr_write(up, UART_ACR, up->acr);
-
-	return value;
-}
-
-/*
- * FIFO support.
- */
-static void serial8250_clear_fifos(struct uart_8250_port *p)
-{
-	if (p->capabilities & UART_CAP_FIFO) {
-		serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO);
-		serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO |
-			       UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
-		serial_out(p, UART_FCR, 0);
-	}
-}
-
-void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p)
-{
-	serial8250_clear_fifos(p);
-	serial_out(p, UART_FCR, p->fcr);
-}
-EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
-
-void serial8250_rpm_get(struct uart_8250_port *p)
-{
-	if (!(p->capabilities & UART_CAP_RPM))
-		return;
-	pm_runtime_get_sync(p->port.dev);
-}
-EXPORT_SYMBOL_GPL(serial8250_rpm_get);
-
-void serial8250_rpm_put(struct uart_8250_port *p)
-{
-	if (!(p->capabilities & UART_CAP_RPM))
-		return;
-	pm_runtime_mark_last_busy(p->port.dev);
-	pm_runtime_put_autosuspend(p->port.dev);
-}
-EXPORT_SYMBOL_GPL(serial8250_rpm_put);
-
-/*
- * These two wrappers ensure that enable_runtime_pm_tx() can be called more than
- * once and disable_runtime_pm_tx() will still disable RPM because the fifo is
- * empty and the HW can idle again.
- */
-static void serial8250_rpm_get_tx(struct uart_8250_port *p)
-{
-	unsigned char rpm_active;
-
-	if (!(p->capabilities & UART_CAP_RPM))
-		return;
-
-	rpm_active = xchg(&p->rpm_tx_active, 1);
-	if (rpm_active)
-		return;
-	pm_runtime_get_sync(p->port.dev);
-}
-
-static void serial8250_rpm_put_tx(struct uart_8250_port *p)
-{
-	unsigned char rpm_active;
-
-	if (!(p->capabilities & UART_CAP_RPM))
-		return;
-
-	rpm_active = xchg(&p->rpm_tx_active, 0);
-	if (!rpm_active)
-		return;
-	pm_runtime_mark_last_busy(p->port.dev);
-	pm_runtime_put_autosuspend(p->port.dev);
-}
-
-/*
- * IER sleep support.  UARTs which have EFRs need the "extended
- * capability" bit enabled.  Note that on XR16C850s, we need to
- * reset LCR to write to IER.
- */
-static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
-{
-	unsigned char lcr = 0, efr = 0;
-	/*
-	 * Exar UARTs have a SLEEP register that enables or disables
-	 * each UART to enter sleep mode separately.  On the XR17V35x the
-	 * register is accessible to each UART at the UART_EXAR_SLEEP
-	 * offset but the UART channel may only write to the corresponding
-	 * bit.
-	 */
-	serial8250_rpm_get(p);
-	if ((p->port.type == PORT_XR17V35X) ||
-	   (p->port.type == PORT_XR17D15X)) {
-		serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0);
-		goto out;
-	}
-
-	if (p->capabilities & UART_CAP_SLEEP) {
-		if (p->capabilities & UART_CAP_EFR) {
-			lcr = serial_in(p, UART_LCR);
-			efr = serial_in(p, UART_EFR);
-			serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
-			serial_out(p, UART_EFR, UART_EFR_ECB);
-			serial_out(p, UART_LCR, 0);
-		}
-		serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
-		if (p->capabilities & UART_CAP_EFR) {
-			serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
-			serial_out(p, UART_EFR, efr);
-			serial_out(p, UART_LCR, lcr);
-		}
-	}
-out:
-	serial8250_rpm_put(p);
-}
-
-#ifdef CONFIG_SERIAL_8250_RSA
-/*
- * Attempts to turn on the RSA FIFO.  Returns zero on failure.
- * We set the port uart clock rate if we succeed.
- */
-static int __enable_rsa(struct uart_8250_port *up)
-{
-	unsigned char mode;
-	int result;
-
-	mode = serial_in(up, UART_RSA_MSR);
-	result = mode & UART_RSA_MSR_FIFO;
-
-	if (!result) {
-		serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
-		mode = serial_in(up, UART_RSA_MSR);
-		result = mode & UART_RSA_MSR_FIFO;
-	}
-
-	if (result)
-		up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
-
-	return result;
-}
-
-static void enable_rsa(struct uart_8250_port *up)
-{
-	if (up->port.type == PORT_RSA) {
-		if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
-			spin_lock_irq(&up->port.lock);
-			__enable_rsa(up);
-			spin_unlock_irq(&up->port.lock);
-		}
-		if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
-			serial_out(up, UART_RSA_FRR, 0);
-	}
-}
-
-/*
- * Attempts to turn off the RSA FIFO.  Returns zero on failure.
- * It is unknown why interrupts were disabled in here.  However,
- * the caller is expected to preserve this behaviour by grabbing
- * the spinlock before calling this function.
- */
-static void disable_rsa(struct uart_8250_port *up)
-{
-	unsigned char mode;
-	int result;
-
-	if (up->port.type == PORT_RSA &&
-	    up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
-		spin_lock_irq(&up->port.lock);
-
-		mode = serial_in(up, UART_RSA_MSR);
-		result = !(mode & UART_RSA_MSR_FIFO);
-
-		if (!result) {
-			serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
-			mode = serial_in(up, UART_RSA_MSR);
-			result = !(mode & UART_RSA_MSR_FIFO);
-		}
-
-		if (result)
-			up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
-		spin_unlock_irq(&up->port.lock);
-	}
-}
-#endif /* CONFIG_SERIAL_8250_RSA */
-
-/*
- * This is a quickie test to see how big the FIFO is.
- * It doesn't work at all the time, more's the pity.
- */
-static int size_fifo(struct uart_8250_port *up)
-{
-	unsigned char old_fcr, old_mcr, old_lcr;
-	unsigned short old_dl;
-	int count;
-
-	old_lcr = serial_in(up, UART_LCR);
-	serial_out(up, UART_LCR, 0);
-	old_fcr = serial_in(up, UART_FCR);
-	old_mcr = serial_in(up, UART_MCR);
-	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
-		    UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
-	serial_out(up, UART_MCR, UART_MCR_LOOP);
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
-	old_dl = serial_dl_read(up);
-	serial_dl_write(up, 0x0001);
-	serial_out(up, UART_LCR, 0x03);
-	for (count = 0; count < 256; count++)
-		serial_out(up, UART_TX, count);
-	mdelay(20);/* FIXME - schedule_timeout */
-	for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) &&
-	     (count < 256); count++)
-		serial_in(up, UART_RX);
-	serial_out(up, UART_FCR, old_fcr);
-	serial_out(up, UART_MCR, old_mcr);
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial_dl_write(up, old_dl);
-	serial_out(up, UART_LCR, old_lcr);
-
-	return count;
-}
-
-/*
- * Read UART ID using the divisor method - set DLL and DLM to zero
- * and the revision will be in DLL and device type in DLM.  We
- * preserve the device state across this.
- */
-static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
-{
-	unsigned char old_dll, old_dlm, old_lcr;
-	unsigned int id;
-
-	old_lcr = serial_in(p, UART_LCR);
-	serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A);
-
-	old_dll = serial_in(p, UART_DLL);
-	old_dlm = serial_in(p, UART_DLM);
-
-	serial_out(p, UART_DLL, 0);
-	serial_out(p, UART_DLM, 0);
-
-	id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8;
-
-	serial_out(p, UART_DLL, old_dll);
-	serial_out(p, UART_DLM, old_dlm);
-	serial_out(p, UART_LCR, old_lcr);
-
-	return id;
-}
-
-/*
- * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's.
- * When this function is called we know it is at least a StarTech
- * 16650 V2, but it might be one of several StarTech UARTs, or one of
- * its clones.  (We treat the broken original StarTech 16650 V1 as a
- * 16550, and why not?  Startech doesn't seem to even acknowledge its
- * existence.)
- *
- * What evil have men's minds wrought...
- */
-static void autoconfig_has_efr(struct uart_8250_port *up)
-{
-	unsigned int id1, id2, id3, rev;
-
-	/*
-	 * Everything with an EFR has SLEEP
-	 */
-	up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
-
-	/*
-	 * First we check to see if it's an Oxford Semiconductor UART.
-	 *
-	 * If we have to do this here because some non-National
-	 * Semiconductor clone chips lock up if you try writing to the
-	 * LSR register (which serial_icr_read does)
-	 */
-
-	/*
-	 * Check for Oxford Semiconductor 16C950.
-	 *
-	 * EFR [4] must be set else this test fails.
-	 *
-	 * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca)
-	 * claims that it's needed for 952 dual UART's (which are not
-	 * recommended for new designs).
-	 */
-	up->acr = 0;
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_out(up, UART_EFR, UART_EFR_ECB);
-	serial_out(up, UART_LCR, 0x00);
-	id1 = serial_icr_read(up, UART_ID1);
-	id2 = serial_icr_read(up, UART_ID2);
-	id3 = serial_icr_read(up, UART_ID3);
-	rev = serial_icr_read(up, UART_REV);
-
-	DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev);
-
-	if (id1 == 0x16 && id2 == 0xC9 &&
-	    (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) {
-		up->port.type = PORT_16C950;
-
-		/*
-		 * Enable work around for the Oxford Semiconductor 952 rev B
-		 * chip which causes it to seriously miscalculate baud rates
-		 * when DLL is 0.
-		 */
-		if (id3 == 0x52 && rev == 0x01)
-			up->bugs |= UART_BUG_QUOT;
-		return;
-	}
-
-	/*
-	 * We check for a XR16C850 by setting DLL and DLM to 0, and then
-	 * reading back DLL and DLM.  The chip type depends on the DLM
-	 * value read back:
-	 *  0x10 - XR16C850 and the DLL contains the chip revision.
-	 *  0x12 - XR16C2850.
-	 *  0x14 - XR16C854.
-	 */
-	id1 = autoconfig_read_divisor_id(up);
-	DEBUG_AUTOCONF("850id=%04x ", id1);
-
-	id2 = id1 >> 8;
-	if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) {
-		up->port.type = PORT_16850;
-		return;
-	}
-
-	/*
-	 * It wasn't an XR16C850.
-	 *
-	 * We distinguish between the '654 and the '650 by counting
-	 * how many bytes are in the FIFO.  I'm using this for now,
-	 * since that's the technique that was sent to me in the
-	 * serial driver update, but I'm not convinced this works.
-	 * I've had problems doing this in the past.  -TYT
-	 */
-	if (size_fifo(up) == 64)
-		up->port.type = PORT_16654;
-	else
-		up->port.type = PORT_16650V2;
-}
-
-/*
- * We detected a chip without a FIFO.  Only two fall into
- * this category - the original 8250 and the 16450.  The
- * 16450 has a scratch register (accessible with LCR=0)
- */
-static void autoconfig_8250(struct uart_8250_port *up)
-{
-	unsigned char scratch, status1, status2;
-
-	up->port.type = PORT_8250;
-
-	scratch = serial_in(up, UART_SCR);
-	serial_out(up, UART_SCR, 0xa5);
-	status1 = serial_in(up, UART_SCR);
-	serial_out(up, UART_SCR, 0x5a);
-	status2 = serial_in(up, UART_SCR);
-	serial_out(up, UART_SCR, scratch);
-
-	if (status1 == 0xa5 && status2 == 0x5a)
-		up->port.type = PORT_16450;
-}
-
-static int broken_efr(struct uart_8250_port *up)
-{
-	/*
-	 * Exar ST16C2550 "A2" devices incorrectly detect as
-	 * having an EFR, and report an ID of 0x0201.  See
-	 * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html
-	 */
-	if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16)
-		return 1;
-
-	return 0;
-}
-
-/*
- * We know that the chip has FIFOs.  Does it have an EFR?  The
- * EFR is located in the same register position as the IIR and
- * we know the top two bits of the IIR are currently set.  The
- * EFR should contain zero.  Try to read the EFR.
- */
-static void autoconfig_16550a(struct uart_8250_port *up)
-{
-	unsigned char status1, status2;
-	unsigned int iersave;
-
-	up->port.type = PORT_16550A;
-	up->capabilities |= UART_CAP_FIFO;
-
-	/*
-	 * XR17V35x UARTs have an extra divisor register, DLD
-	 * that gets enabled with when DLAB is set which will
-	 * cause the device to incorrectly match and assign
-	 * port type to PORT_16650.  The EFR for this UART is
-	 * found at offset 0x09. Instead check the Deice ID (DVID)
-	 * register for a 2, 4 or 8 port UART.
-	 */
-	if (up->port.flags & UPF_EXAR_EFR) {
-		status1 = serial_in(up, UART_EXAR_DVID);
-		if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
-			DEBUG_AUTOCONF("Exar XR17V35x ");
-			up->port.type = PORT_XR17V35X;
-			up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
-						UART_CAP_SLEEP;
-
-			return;
-		}
-
-	}
-
-	/*
-	 * Check for presence of the EFR when DLAB is set.
-	 * Only ST16C650V1 UARTs pass this test.
-	 */
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
-	if (serial_in(up, UART_EFR) == 0) {
-		serial_out(up, UART_EFR, 0xA8);
-		if (serial_in(up, UART_EFR) != 0) {
-			DEBUG_AUTOCONF("EFRv1 ");
-			up->port.type = PORT_16650;
-			up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
-		} else {
-			serial_out(up, UART_LCR, 0);
-			serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
-				   UART_FCR7_64BYTE);
-			status1 = serial_in(up, UART_IIR) >> 5;
-			serial_out(up, UART_FCR, 0);
-			serial_out(up, UART_LCR, 0);
-
-			if (status1 == 7)
-				up->port.type = PORT_16550A_FSL64;
-			else
-				DEBUG_AUTOCONF("Motorola 8xxx DUART ");
-		}
-		serial_out(up, UART_EFR, 0);
-		return;
-	}
-
-	/*
-	 * Maybe it requires 0xbf to be written to the LCR.
-	 * (other ST16C650V2 UARTs, TI16C752A, etc)
-	 */
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-	if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
-		DEBUG_AUTOCONF("EFRv2 ");
-		autoconfig_has_efr(up);
-		return;
-	}
-
-	/*
-	 * Check for a National Semiconductor SuperIO chip.
-	 * Attempt to switch to bank 2, read the value of the LOOP bit
-	 * from EXCR1. Switch back to bank 0, change it in MCR. Then
-	 * switch back to bank 2, read it from EXCR1 again and check
-	 * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
-	 */
-	serial_out(up, UART_LCR, 0);
-	status1 = serial_in(up, UART_MCR);
-	serial_out(up, UART_LCR, 0xE0);
-	status2 = serial_in(up, 0x02); /* EXCR1 */
-
-	if (!((status2 ^ status1) & UART_MCR_LOOP)) {
-		serial_out(up, UART_LCR, 0);
-		serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP);
-		serial_out(up, UART_LCR, 0xE0);
-		status2 = serial_in(up, 0x02); /* EXCR1 */
-		serial_out(up, UART_LCR, 0);
-		serial_out(up, UART_MCR, status1);
-
-		if ((status2 ^ status1) & UART_MCR_LOOP) {
-			unsigned short quot;
-
-			serial_out(up, UART_LCR, 0xE0);
-
-			quot = serial_dl_read(up);
-			quot <<= 3;
-
-			if (ns16550a_goto_highspeed(up))
-				serial_dl_write(up, quot);
-
-			serial_out(up, UART_LCR, 0);
-
-			up->port.uartclk = 921600*16;
-			up->port.type = PORT_NS16550A;
-			up->capabilities |= UART_NATSEMI;
-			return;
-		}
-	}
-
-	/*
-	 * No EFR.  Try to detect a TI16750, which only sets bit 5 of
-	 * the IIR when 64 byte FIFO mode is enabled when DLAB is set.
-	 * Try setting it with and without DLAB set.  Cheap clones
-	 * set bit 5 without DLAB set.
-	 */
-	serial_out(up, UART_LCR, 0);
-	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
-	status1 = serial_in(up, UART_IIR) >> 5;
-	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
-	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
-	status2 = serial_in(up, UART_IIR) >> 5;
-	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
-	serial_out(up, UART_LCR, 0);
-
-	DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
-
-	if (status1 == 6 && status2 == 7) {
-		up->port.type = PORT_16750;
-		up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
-		return;
-	}
-
-	/*
-	 * Try writing and reading the UART_IER_UUE bit (b6).
-	 * If it works, this is probably one of the Xscale platform's
-	 * internal UARTs.
-	 * We're going to explicitly set the UUE bit to 0 before
-	 * trying to write and read a 1 just to make sure it's not
-	 * already a 1 and maybe locked there before we even start start.
-	 */
-	iersave = serial_in(up, UART_IER);
-	serial_out(up, UART_IER, iersave & ~UART_IER_UUE);
-	if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
-		/*
-		 * OK it's in a known zero state, try writing and reading
-		 * without disturbing the current state of the other bits.
-		 */
-		serial_out(up, UART_IER, iersave | UART_IER_UUE);
-		if (serial_in(up, UART_IER) & UART_IER_UUE) {
-			/*
-			 * It's an Xscale.
-			 * We'll leave the UART_IER_UUE bit set to 1 (enabled).
-			 */
-			DEBUG_AUTOCONF("Xscale ");
-			up->port.type = PORT_XSCALE;
-			up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE;
-			return;
-		}
-	} else {
-		/*
-		 * If we got here we couldn't force the IER_UUE bit to 0.
-		 * Log it and continue.
-		 */
-		DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
-	}
-	serial_out(up, UART_IER, iersave);
-
-	/*
-	 * Exar uarts have EFR in a weird location
-	 */
-	if (up->port.flags & UPF_EXAR_EFR) {
-		DEBUG_AUTOCONF("Exar XR17D15x ");
-		up->port.type = PORT_XR17D15X;
-		up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
-				    UART_CAP_SLEEP;
-
-		return;
-	}
-
-	/*
-	 * We distinguish between 16550A and U6 16550A by counting
-	 * how many bytes are in the FIFO.
-	 */
-	if (up->port.type == PORT_16550A && size_fifo(up) == 64) {
-		up->port.type = PORT_U6_16550A;
-		up->capabilities |= UART_CAP_AFE;
-	}
-}
-
-/*
- * This routine is called by rs_init() to initialize a specific serial
- * port.  It determines what type of UART chip this serial port is
- * using: 8250, 16450, 16550, 16550A.  The important question is
- * whether or not this UART is a 16550A or not, since this will
- * determine whether or not we can use its FIFO features or not.
- */
-static void autoconfig(struct uart_8250_port *up)
-{
-	unsigned char status1, scratch, scratch2, scratch3;
-	unsigned char save_lcr, save_mcr;
-	struct uart_port *port = &up->port;
-	unsigned long flags;
-	unsigned int old_capabilities;
-
-	if (!port->iobase && !port->mapbase && !port->membase)
-		return;
-
-	DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ",
-		       serial_index(port), port->iobase, port->membase);
-
-	/*
-	 * We really do need global IRQs disabled here - we're going to
-	 * be frobbing the chips IRQ enable register to see if it exists.
-	 */
-	spin_lock_irqsave(&port->lock, flags);
-
-	up->capabilities = 0;
-	up->bugs = 0;
-
-	if (!(port->flags & UPF_BUGGY_UART)) {
-		/*
-		 * Do a simple existence test first; if we fail this,
-		 * there's no point trying anything else.
-		 *
-		 * 0x80 is used as a nonsense port to prevent against
-		 * false positives due to ISA bus float.  The
-		 * assumption is that 0x80 is a non-existent port;
-		 * which should be safe since include/asm/io.h also
-		 * makes this assumption.
-		 *
-		 * Note: this is safe as long as MCR bit 4 is clear
-		 * and the device is in "PC" mode.
-		 */
-		scratch = serial_in(up, UART_IER);
-		serial_out(up, UART_IER, 0);
-#ifdef __i386__
-		outb(0xff, 0x080);
-#endif
-		/*
-		 * Mask out IER[7:4] bits for test as some UARTs (e.g. TL
-		 * 16C754B) allow only to modify them if an EFR bit is set.
-		 */
-		scratch2 = serial_in(up, UART_IER) & 0x0f;
-		serial_out(up, UART_IER, 0x0F);
-#ifdef __i386__
-		outb(0, 0x080);
-#endif
-		scratch3 = serial_in(up, UART_IER) & 0x0f;
-		serial_out(up, UART_IER, scratch);
-		if (scratch2 != 0 || scratch3 != 0x0F) {
-			/*
-			 * We failed; there's nothing here
-			 */
-			spin_unlock_irqrestore(&port->lock, flags);
-			DEBUG_AUTOCONF("IER test failed (%02x, %02x) ",
-				       scratch2, scratch3);
-			goto out;
-		}
-	}
-
-	save_mcr = serial_in(up, UART_MCR);
-	save_lcr = serial_in(up, UART_LCR);
-
-	/*
-	 * Check to see if a UART is really there.  Certain broken
-	 * internal modems based on the Rockwell chipset fail this
-	 * test, because they apparently don't implement the loopback
-	 * test mode.  So this test is skipped on the COM 1 through
-	 * COM 4 ports.  This *should* be safe, since no board
-	 * manufacturer would be stupid enough to design a board
-	 * that conflicts with COM 1-4 --- we hope!
-	 */
-	if (!(port->flags & UPF_SKIP_TEST)) {
-		serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A);
-		status1 = serial_in(up, UART_MSR) & 0xF0;
-		serial_out(up, UART_MCR, save_mcr);
-		if (status1 != 0x90) {
-			spin_unlock_irqrestore(&port->lock, flags);
-			DEBUG_AUTOCONF("LOOP test failed (%02x) ",
-				       status1);
-			goto out;
-		}
-	}
-
-	/*
-	 * We're pretty sure there's a port here.  Lets find out what
-	 * type of port it is.  The IIR top two bits allows us to find
-	 * out if it's 8250 or 16450, 16550, 16550A or later.  This
-	 * determines what we test for next.
-	 *
-	 * We also initialise the EFR (if any) to zero for later.  The
-	 * EFR occupies the same register location as the FCR and IIR.
-	 */
-	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-	serial_out(up, UART_EFR, 0);
-	serial_out(up, UART_LCR, 0);
-
-	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
-	scratch = serial_in(up, UART_IIR) >> 6;
-
-	switch (scratch) {
-	case 0:
-		autoconfig_8250(up);
-		break;
-	case 1:
-		port->type = PORT_UNKNOWN;
-		break;
-	case 2:
-		port->type = PORT_16550;
-		break;
-	case 3:
-		autoconfig_16550a(up);
-		break;
-	}
-
-#ifdef CONFIG_SERIAL_8250_RSA
-	/*
-	 * Only probe for RSA ports if we got the region.
-	 */
-	if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA &&
-	    __enable_rsa(up))
-		port->type = PORT_RSA;
-#endif
-
-	serial_out(up, UART_LCR, save_lcr);
-
-	port->fifosize = uart_config[up->port.type].fifo_size;
-	old_capabilities = up->capabilities;
-	up->capabilities = uart_config[port->type].flags;
-	up->tx_loadsz = uart_config[port->type].tx_loadsz;
-
-	if (port->type == PORT_UNKNOWN)
-		goto out_lock;
-
-	/*
-	 * Reset the UART.
-	 */
-#ifdef CONFIG_SERIAL_8250_RSA
-	if (port->type == PORT_RSA)
-		serial_out(up, UART_RSA_FRR, 0);
-#endif
-	serial_out(up, UART_MCR, save_mcr);
-	serial8250_clear_fifos(up);
-	serial_in(up, UART_RX);
-	if (up->capabilities & UART_CAP_UUE)
-		serial_out(up, UART_IER, UART_IER_UUE);
-	else
-		serial_out(up, UART_IER, 0);
-
-out_lock:
-	spin_unlock_irqrestore(&port->lock, flags);
-	if (up->capabilities != old_capabilities) {
-		printk(KERN_WARNING
-		       "ttyS%d: detected caps %08x should be %08x\n",
-		       serial_index(port), old_capabilities,
-		       up->capabilities);
-	}
-out:
-	DEBUG_AUTOCONF("iir=%d ", scratch);
-	DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name);
-}
-
-static void autoconfig_irq(struct uart_8250_port *up)
-{
-	struct uart_port *port = &up->port;
-	unsigned char save_mcr, save_ier;
-	unsigned char save_ICP = 0;
-	unsigned int ICP = 0;
-	unsigned long irqs;
-	int irq;
-
-	if (port->flags & UPF_FOURPORT) {
-		ICP = (port->iobase & 0xfe0) | 0x1f;
-		save_ICP = inb_p(ICP);
-		outb_p(0x80, ICP);
-		inb_p(ICP);
-	}
-
-	/* forget possible initially masked and pending IRQ */
-	probe_irq_off(probe_irq_on());
-	save_mcr = serial_in(up, UART_MCR);
-	save_ier = serial_in(up, UART_IER);
-	serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
-
-	irqs = probe_irq_on();
-	serial_out(up, UART_MCR, 0);
-	udelay(10);
-	if (port->flags & UPF_FOURPORT) {
-		serial_out(up, UART_MCR,
-			    UART_MCR_DTR | UART_MCR_RTS);
-	} else {
-		serial_out(up, UART_MCR,
-			    UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
-	}
-	serial_out(up, UART_IER, 0x0f);	/* enable all intrs */
-	serial_in(up, UART_LSR);
-	serial_in(up, UART_RX);
-	serial_in(up, UART_IIR);
-	serial_in(up, UART_MSR);
-	serial_out(up, UART_TX, 0xFF);
-	udelay(20);
-	irq = probe_irq_off(irqs);
-
-	serial_out(up, UART_MCR, save_mcr);
-	serial_out(up, UART_IER, save_ier);
-
-	if (port->flags & UPF_FOURPORT)
-		outb_p(save_ICP, ICP);
-
-	port->irq = (irq > 0) ? irq : 0;
-}
-
-static inline void __stop_tx(struct uart_8250_port *p)
-{
-	if (p->ier & UART_IER_THRI) {
-		p->ier &= ~UART_IER_THRI;
-		serial_out(p, UART_IER, p->ier);
-		serial8250_rpm_put_tx(p);
-	}
-}
-
-static void serial8250_stop_tx(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	serial8250_rpm_get(up);
-	__stop_tx(up);
-
-	/*
-	 * We really want to stop the transmitter from sending.
-	 */
-	if (port->type == PORT_16C950) {
-		up->acr |= UART_ACR_TXDIS;
-		serial_icr_write(up, UART_ACR, up->acr);
-	}
-	serial8250_rpm_put(up);
-}
-
-static void serial8250_start_tx(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	serial8250_rpm_get_tx(up);
-
-	if (up->dma && !up->dma->tx_dma(up))
-		return;
-
-	if (!(up->ier & UART_IER_THRI)) {
-		up->ier |= UART_IER_THRI;
-		serial_port_out(port, UART_IER, up->ier);
-
-		if (up->bugs & UART_BUG_TXEN) {
-			unsigned char lsr;
-			lsr = serial_in(up, UART_LSR);
-			up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
-			if (lsr & UART_LSR_THRE)
-				serial8250_tx_chars(up);
-		}
-	}
-
-	/*
-	 * Re-enable the transmitter if we disabled it.
-	 */
-	if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
-		up->acr &= ~UART_ACR_TXDIS;
-		serial_icr_write(up, UART_ACR, up->acr);
-	}
-}
-
-static void serial8250_throttle(struct uart_port *port)
-{
-	port->throttle(port);
-}
-
-static void serial8250_unthrottle(struct uart_port *port)
-{
-	port->unthrottle(port);
-}
-
-static void serial8250_stop_rx(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	serial8250_rpm_get(up);
-
-	up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
-	up->port.read_status_mask &= ~UART_LSR_DR;
-	serial_port_out(port, UART_IER, up->ier);
-
-	serial8250_rpm_put(up);
-}
-
-static void serial8250_disable_ms(struct uart_port *port)
-{
-	struct uart_8250_port *up =
-		container_of(port, struct uart_8250_port, port);
-
-	/* no MSR capabilities */
-	if (up->bugs & UART_BUG_NOMSR)
-		return;
-
-	up->ier &= ~UART_IER_MSI;
-	serial_port_out(port, UART_IER, up->ier);
-}
-
-static void serial8250_enable_ms(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	/* no MSR capabilities */
-	if (up->bugs & UART_BUG_NOMSR)
-		return;
-
-	up->ier |= UART_IER_MSI;
-
-	serial8250_rpm_get(up);
-	serial_port_out(port, UART_IER, up->ier);
-	serial8250_rpm_put(up);
-}
-
-/*
- * serial8250_rx_chars: processes according to the passed in LSR
- * value, and returns the remaining LSR bits not handled
- * by this Rx routine.
- */
-unsigned char
-serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
-{
-	struct uart_port *port = &up->port;
-	unsigned char ch;
-	int max_count = 256;
-	char flag;
-
-	do {
-		if (likely(lsr & UART_LSR_DR))
-			ch = serial_in(up, UART_RX);
-		else
-			/*
-			 * Intel 82571 has a Serial Over Lan device that will
-			 * set UART_LSR_BI without setting UART_LSR_DR when
-			 * it receives a break. To avoid reading from the
-			 * receive buffer without UART_LSR_DR bit set, we
-			 * just force the read character to be 0
-			 */
-			ch = 0;
-
-		flag = TTY_NORMAL;
-		port->icount.rx++;
-
-		lsr |= up->lsr_saved_flags;
-		up->lsr_saved_flags = 0;
-
-		if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
-			if (lsr & UART_LSR_BI) {
-				lsr &= ~(UART_LSR_FE | UART_LSR_PE);
-				port->icount.brk++;
-				/*
-				 * We do the SysRQ and SAK checking
-				 * here because otherwise the break
-				 * may get masked by ignore_status_mask
-				 * or read_status_mask.
-				 */
-				if (uart_handle_break(port))
-					goto ignore_char;
-			} else if (lsr & UART_LSR_PE)
-				port->icount.parity++;
-			else if (lsr & UART_LSR_FE)
-				port->icount.frame++;
-			if (lsr & UART_LSR_OE)
-				port->icount.overrun++;
-
-			/*
-			 * Mask off conditions which should be ignored.
-			 */
-			lsr &= port->read_status_mask;
-
-			if (lsr & UART_LSR_BI) {
-				DEBUG_INTR("handling break....");
-				flag = TTY_BREAK;
-			} else if (lsr & UART_LSR_PE)
-				flag = TTY_PARITY;
-			else if (lsr & UART_LSR_FE)
-				flag = TTY_FRAME;
-		}
-		if (uart_handle_sysrq_char(port, ch))
-			goto ignore_char;
-
-		uart_insert_char(port, lsr, UART_LSR_OE, ch, flag);
-
-ignore_char:
-		lsr = serial_in(up, UART_LSR);
-	} while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0));
-	spin_unlock(&port->lock);
-	tty_flip_buffer_push(&port->state->port);
-	spin_lock(&port->lock);
-	return lsr;
-}
-EXPORT_SYMBOL_GPL(serial8250_rx_chars);
-
-void serial8250_tx_chars(struct uart_8250_port *up)
-{
-	struct uart_port *port = &up->port;
-	struct circ_buf *xmit = &port->state->xmit;
-	int count;
-
-	if (port->x_char) {
-		serial_out(up, UART_TX, port->x_char);
-		port->icount.tx++;
-		port->x_char = 0;
-		return;
-	}
-	if (uart_tx_stopped(port)) {
-		serial8250_stop_tx(port);
-		return;
-	}
-	if (uart_circ_empty(xmit)) {
-		__stop_tx(up);
-		return;
-	}
-
-	count = up->tx_loadsz;
-	do {
-		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
-		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
-		port->icount.tx++;
-		if (uart_circ_empty(xmit))
-			break;
-		if (up->capabilities & UART_CAP_HFIFO) {
-			if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) !=
-			    BOTH_EMPTY)
-				break;
-		}
-	} while (--count > 0);
-
-	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-		uart_write_wakeup(port);
-
-	DEBUG_INTR("THRE...");
-
-	/*
-	 * With RPM enabled, we have to wait until the FIFO is empty before the
-	 * HW can go idle. So we get here once again with empty FIFO and disable
-	 * the interrupt and RPM in __stop_tx()
-	 */
-	if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
-		__stop_tx(up);
-}
-EXPORT_SYMBOL_GPL(serial8250_tx_chars);
-
-/* Caller holds uart port lock */
-unsigned int serial8250_modem_status(struct uart_8250_port *up)
-{
-	struct uart_port *port = &up->port;
-	unsigned int status = serial_in(up, UART_MSR);
-
-	status |= up->msr_saved_flags;
-	up->msr_saved_flags = 0;
-	if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
-	    port->state != NULL) {
-		if (status & UART_MSR_TERI)
-			port->icount.rng++;
-		if (status & UART_MSR_DDSR)
-			port->icount.dsr++;
-		if (status & UART_MSR_DDCD)
-			uart_handle_dcd_change(port, status & UART_MSR_DCD);
-		if (status & UART_MSR_DCTS)
-			uart_handle_cts_change(port, status & UART_MSR_CTS);
-
-		wake_up_interruptible(&port->state->port.delta_msr_wait);
-	}
-
-	return status;
-}
-EXPORT_SYMBOL_GPL(serial8250_modem_status);
-
-/*
- * This handles the interrupt from one port.
- */
-int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
-{
-	unsigned char status;
-	unsigned long flags;
-	struct uart_8250_port *up = up_to_u8250p(port);
-	int dma_err = 0;
-
-	if (iir & UART_IIR_NO_INT)
-		return 0;
-
-	spin_lock_irqsave(&port->lock, flags);
-
-	status = serial_port_in(port, UART_LSR);
-
-	DEBUG_INTR("status = %x...", status);
-
-	if (status & (UART_LSR_DR | UART_LSR_BI)) {
-		if (up->dma)
-			dma_err = up->dma->rx_dma(up, iir);
-
-		if (!up->dma || dma_err)
-			status = serial8250_rx_chars(up, status);
-	}
-	serial8250_modem_status(up);
-	if ((!up->dma || (up->dma && up->dma->tx_err)) &&
-	    (status & UART_LSR_THRE))
-		serial8250_tx_chars(up);
-
-	spin_unlock_irqrestore(&port->lock, flags);
-	return 1;
-}
-EXPORT_SYMBOL_GPL(serial8250_handle_irq);
-
-static int serial8250_default_handle_irq(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned int iir;
-	int ret;
-
-	serial8250_rpm_get(up);
-
-	iir = serial_port_in(port, UART_IIR);
-	ret = serial8250_handle_irq(port, iir);
-
-	serial8250_rpm_put(up);
-	return ret;
-}
-
-/*
- * These Exar UARTs have an extra interrupt indicator that could
- * fire for a few unimplemented interrupts.  One of which is a
- * wakeup event when coming out of sleep.  Put this here just
- * to be on the safe side that these interrupts don't go unhandled.
- */
-static int exar_handle_irq(struct uart_port *port)
-{
-	unsigned char int0, int1, int2, int3;
-	unsigned int iir = serial_port_in(port, UART_IIR);
-	int ret;
-
-	ret = serial8250_handle_irq(port, iir);
-
-	if ((port->type == PORT_XR17V35X) ||
-	   (port->type == PORT_XR17D15X)) {
-		int0 = serial_port_in(port, 0x80);
-		int1 = serial_port_in(port, 0x81);
-		int2 = serial_port_in(port, 0x82);
-		int3 = serial_port_in(port, 0x83);
-	}
-
-	return ret;
-}
-
-/*
  * This is the serial driver's interrupt routine.
  *
  * Arjan thinks the old way was overly complex, so it got simplified.
@@ -1964,875 +368,6 @@ static void univ8250_release_irq(struct uart_8250_port *up)
 		serial_unlink_irq_chain(up);
 }
 
-static unsigned int serial8250_tx_empty(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned long flags;
-	unsigned int lsr;
-
-	serial8250_rpm_get(up);
-
-	spin_lock_irqsave(&port->lock, flags);
-	lsr = serial_port_in(port, UART_LSR);
-	up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
-	spin_unlock_irqrestore(&port->lock, flags);
-
-	serial8250_rpm_put(up);
-
-	return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
-}
-
-static unsigned int serial8250_get_mctrl(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned int status;
-	unsigned int ret;
-
-	serial8250_rpm_get(up);
-	status = serial8250_modem_status(up);
-	serial8250_rpm_put(up);
-
-	ret = 0;
-	if (status & UART_MSR_DCD)
-		ret |= TIOCM_CAR;
-	if (status & UART_MSR_RI)
-		ret |= TIOCM_RNG;
-	if (status & UART_MSR_DSR)
-		ret |= TIOCM_DSR;
-	if (status & UART_MSR_CTS)
-		ret |= TIOCM_CTS;
-	return ret;
-}
-
-void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned char mcr = 0;
-
-	if (mctrl & TIOCM_RTS)
-		mcr |= UART_MCR_RTS;
-	if (mctrl & TIOCM_DTR)
-		mcr |= UART_MCR_DTR;
-	if (mctrl & TIOCM_OUT1)
-		mcr |= UART_MCR_OUT1;
-	if (mctrl & TIOCM_OUT2)
-		mcr |= UART_MCR_OUT2;
-	if (mctrl & TIOCM_LOOP)
-		mcr |= UART_MCR_LOOP;
-
-	mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
-
-	serial_port_out(port, UART_MCR, mcr);
-}
-EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl);
-
-static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-	if (port->set_mctrl)
-		return port->set_mctrl(port, mctrl);
-	return serial8250_do_set_mctrl(port, mctrl);
-}
-
-static void serial8250_break_ctl(struct uart_port *port, int break_state)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned long flags;
-
-	serial8250_rpm_get(up);
-	spin_lock_irqsave(&port->lock, flags);
-	if (break_state == -1)
-		up->lcr |= UART_LCR_SBC;
-	else
-		up->lcr &= ~UART_LCR_SBC;
-	serial_port_out(port, UART_LCR, up->lcr);
-	spin_unlock_irqrestore(&port->lock, flags);
-	serial8250_rpm_put(up);
-}
-
-/*
- *	Wait for transmitter & holding register to empty
- */
-static void wait_for_xmitr(struct uart_8250_port *up, int bits)
-{
-	unsigned int status, tmout = 10000;
-
-	/* Wait up to 10ms for the character(s) to be sent. */
-	for (;;) {
-		status = serial_in(up, UART_LSR);
-
-		up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
-
-		if ((status & bits) == bits)
-			break;
-		if (--tmout == 0)
-			break;
-		udelay(1);
-	}
-
-	/* Wait up to 1s for flow control if necessary */
-	if (up->port.flags & UPF_CONS_FLOW) {
-		unsigned int tmout;
-		for (tmout = 1000000; tmout; tmout--) {
-			unsigned int msr = serial_in(up, UART_MSR);
-			up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
-			if (msr & UART_MSR_CTS)
-				break;
-			udelay(1);
-			touch_nmi_watchdog();
-		}
-	}
-}
-
-#ifdef CONFIG_CONSOLE_POLL
-/*
- * Console polling routines for writing and reading from the uart while
- * in an interrupt or debug context.
- */
-
-static int serial8250_get_poll_char(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned char lsr;
-	int status;
-
-	serial8250_rpm_get(up);
-
-	lsr = serial_port_in(port, UART_LSR);
-
-	if (!(lsr & UART_LSR_DR)) {
-		status = NO_POLL_CHAR;
-		goto out;
-	}
-
-	status = serial_port_in(port, UART_RX);
-out:
-	serial8250_rpm_put(up);
-	return status;
-}
-
-
-static void serial8250_put_poll_char(struct uart_port *port,
-			 unsigned char c)
-{
-	unsigned int ier;
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	serial8250_rpm_get(up);
-	/*
-	 *	First save the IER then disable the interrupts
-	 */
-	ier = serial_port_in(port, UART_IER);
-	if (up->capabilities & UART_CAP_UUE)
-		serial_port_out(port, UART_IER, UART_IER_UUE);
-	else
-		serial_port_out(port, UART_IER, 0);
-
-	wait_for_xmitr(up, BOTH_EMPTY);
-	/*
-	 *	Send the character out.
-	 */
-	serial_port_out(port, UART_TX, c);
-
-	/*
-	 *	Finally, wait for transmitter to become empty
-	 *	and restore the IER
-	 */
-	wait_for_xmitr(up, BOTH_EMPTY);
-	serial_port_out(port, UART_IER, ier);
-	serial8250_rpm_put(up);
-}
-
-#endif /* CONFIG_CONSOLE_POLL */
-
-int serial8250_do_startup(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned long flags;
-	unsigned char lsr, iir;
-	int retval;
-
-	if (port->type == PORT_8250_CIR)
-		return -ENODEV;
-
-	if (!port->fifosize)
-		port->fifosize = uart_config[port->type].fifo_size;
-	if (!up->tx_loadsz)
-		up->tx_loadsz = uart_config[port->type].tx_loadsz;
-	if (!up->capabilities)
-		up->capabilities = uart_config[port->type].flags;
-	up->mcr = 0;
-
-	if (port->iotype != up->cur_iotype)
-		set_io_from_upio(port);
-
-	serial8250_rpm_get(up);
-	if (port->type == PORT_16C950) {
-		/* Wake up and initialize UART */
-		up->acr = 0;
-		serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
-		serial_port_out(port, UART_EFR, UART_EFR_ECB);
-		serial_port_out(port, UART_IER, 0);
-		serial_port_out(port, UART_LCR, 0);
-		serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
-		serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
-		serial_port_out(port, UART_EFR, UART_EFR_ECB);
-		serial_port_out(port, UART_LCR, 0);
-	}
-
-#ifdef CONFIG_SERIAL_8250_RSA
-	/*
-	 * If this is an RSA port, see if we can kick it up to the
-	 * higher speed clock.
-	 */
-	enable_rsa(up);
-#endif
-	/*
-	 * Clear the FIFO buffers and disable them.
-	 * (they will be reenabled in set_termios())
-	 */
-	serial8250_clear_fifos(up);
-
-	/*
-	 * Clear the interrupt registers.
-	 */
-	serial_port_in(port, UART_LSR);
-	serial_port_in(port, UART_RX);
-	serial_port_in(port, UART_IIR);
-	serial_port_in(port, UART_MSR);
-
-	/*
-	 * At this point, there's no way the LSR could still be 0xff;
-	 * if it is, then bail out, because there's likely no UART
-	 * here.
-	 */
-	if (!(port->flags & UPF_BUGGY_UART) &&
-	    (serial_port_in(port, UART_LSR) == 0xff)) {
-		printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
-				   serial_index(port));
-		retval = -ENODEV;
-		goto out;
-	}
-
-	/*
-	 * For a XR16C850, we need to set the trigger levels
-	 */
-	if (port->type == PORT_16850) {
-		unsigned char fctr;
-
-		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-
-		fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
-		serial_port_out(port, UART_FCTR,
-				fctr | UART_FCTR_TRGD | UART_FCTR_RX);
-		serial_port_out(port, UART_TRG, UART_TRG_96);
-		serial_port_out(port, UART_FCTR,
-				fctr | UART_FCTR_TRGD | UART_FCTR_TX);
-		serial_port_out(port, UART_TRG, UART_TRG_96);
-
-		serial_port_out(port, UART_LCR, 0);
-	}
-
-	if (port->irq) {
-		unsigned char iir1;
-		/*
-		 * Test for UARTs that do not reassert THRE when the
-		 * transmitter is idle and the interrupt has already
-		 * been cleared.  Real 16550s should always reassert
-		 * this interrupt whenever the transmitter is idle and
-		 * the interrupt is enabled.  Delays are necessary to
-		 * allow register changes to become visible.
-		 */
-		spin_lock_irqsave(&port->lock, flags);
-		if (up->port.irqflags & IRQF_SHARED)
-			disable_irq_nosync(port->irq);
-
-		wait_for_xmitr(up, UART_LSR_THRE);
-		serial_port_out_sync(port, UART_IER, UART_IER_THRI);
-		udelay(1); /* allow THRE to set */
-		iir1 = serial_port_in(port, UART_IIR);
-		serial_port_out(port, UART_IER, 0);
-		serial_port_out_sync(port, UART_IER, UART_IER_THRI);
-		udelay(1); /* allow a working UART time to re-assert THRE */
-		iir = serial_port_in(port, UART_IIR);
-		serial_port_out(port, UART_IER, 0);
-
-		if (port->irqflags & IRQF_SHARED)
-			enable_irq(port->irq);
-		spin_unlock_irqrestore(&port->lock, flags);
-
-		/*
-		 * If the interrupt is not reasserted, or we otherwise
-		 * don't trust the iir, setup a timer to kick the UART
-		 * on a regular basis.
-		 */
-		if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) ||
-		    up->port.flags & UPF_BUG_THRE) {
-			up->bugs |= UART_BUG_THRE;
-		}
-	}
-
-	retval = up->ops->setup_irq(up);
-	if (retval)
-		goto out;
-
-	/*
-	 * Now, initialize the UART
-	 */
-	serial_port_out(port, UART_LCR, UART_LCR_WLEN8);
-
-	spin_lock_irqsave(&port->lock, flags);
-	if (up->port.flags & UPF_FOURPORT) {
-		if (!up->port.irq)
-			up->port.mctrl |= TIOCM_OUT1;
-	} else
-		/*
-		 * Most PC uarts need OUT2 raised to enable interrupts.
-		 */
-		if (port->irq)
-			up->port.mctrl |= TIOCM_OUT2;
-
-	serial8250_set_mctrl(port, port->mctrl);
-
-	/* Serial over Lan (SoL) hack:
-	   Intel 8257x Gigabit ethernet chips have a
-	   16550 emulation, to be used for Serial Over Lan.
-	   Those chips take a longer time than a normal
-	   serial device to signalize that a transmission
-	   data was queued. Due to that, the above test generally
-	   fails. One solution would be to delay the reading of
-	   iir. However, this is not reliable, since the timeout
-	   is variable. So, let's just don't test if we receive
-	   TX irq. This way, we'll never enable UART_BUG_TXEN.
-	 */
-	if (up->port.flags & UPF_NO_TXEN_TEST)
-		goto dont_test_tx_en;
-
-	/*
-	 * Do a quick test to see if we receive an
-	 * interrupt when we enable the TX irq.
-	 */
-	serial_port_out(port, UART_IER, UART_IER_THRI);
-	lsr = serial_port_in(port, UART_LSR);
-	iir = serial_port_in(port, UART_IIR);
-	serial_port_out(port, UART_IER, 0);
-
-	if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
-		if (!(up->bugs & UART_BUG_TXEN)) {
-			up->bugs |= UART_BUG_TXEN;
-			pr_debug("ttyS%d - enabling bad tx status workarounds\n",
-				 serial_index(port));
-		}
-	} else {
-		up->bugs &= ~UART_BUG_TXEN;
-	}
-
-dont_test_tx_en:
-	spin_unlock_irqrestore(&port->lock, flags);
-
-	/*
-	 * Clear the interrupt registers again for luck, and clear the
-	 * saved flags to avoid getting false values from polling
-	 * routines or the previous session.
-	 */
-	serial_port_in(port, UART_LSR);
-	serial_port_in(port, UART_RX);
-	serial_port_in(port, UART_IIR);
-	serial_port_in(port, UART_MSR);
-	up->lsr_saved_flags = 0;
-	up->msr_saved_flags = 0;
-
-	/*
-	 * Request DMA channels for both RX and TX.
-	 */
-	if (up->dma) {
-		retval = serial8250_request_dma(up);
-		if (retval) {
-			pr_warn_ratelimited("ttyS%d - failed to request DMA\n",
-					    serial_index(port));
-			up->dma = NULL;
-		}
-	}
-
-	/*
-	 * Finally, enable interrupts.  Note: Modem status interrupts
-	 * are set via set_termios(), which will be occurring imminently
-	 * anyway, so we don't enable them here.
-	 */
-	up->ier = UART_IER_RLSI | UART_IER_RDI;
-	serial_port_out(port, UART_IER, up->ier);
-
-	if (port->flags & UPF_FOURPORT) {
-		unsigned int icp;
-		/*
-		 * Enable interrupts on the AST Fourport board
-		 */
-		icp = (port->iobase & 0xfe0) | 0x01f;
-		outb_p(0x80, icp);
-		inb_p(icp);
-	}
-	retval = 0;
-out:
-	serial8250_rpm_put(up);
-	return retval;
-}
-EXPORT_SYMBOL_GPL(serial8250_do_startup);
-
-static int serial8250_startup(struct uart_port *port)
-{
-	if (port->startup)
-		return port->startup(port);
-	return serial8250_do_startup(port);
-}
-
-void serial8250_do_shutdown(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned long flags;
-
-	serial8250_rpm_get(up);
-	/*
-	 * Disable interrupts from this port
-	 */
-	up->ier = 0;
-	serial_port_out(port, UART_IER, 0);
-
-	if (up->dma)
-		serial8250_release_dma(up);
-
-	spin_lock_irqsave(&port->lock, flags);
-	if (port->flags & UPF_FOURPORT) {
-		/* reset interrupts on the AST Fourport board */
-		inb((port->iobase & 0xfe0) | 0x1f);
-		port->mctrl |= TIOCM_OUT1;
-	} else
-		port->mctrl &= ~TIOCM_OUT2;
-
-	serial8250_set_mctrl(port, port->mctrl);
-	spin_unlock_irqrestore(&port->lock, flags);
-
-	/*
-	 * Disable break condition and FIFOs
-	 */
-	serial_port_out(port, UART_LCR,
-			serial_port_in(port, UART_LCR) & ~UART_LCR_SBC);
-	serial8250_clear_fifos(up);
-
-#ifdef CONFIG_SERIAL_8250_RSA
-	/*
-	 * Reset the RSA board back to 115kbps compat mode.
-	 */
-	disable_rsa(up);
-#endif
-
-	/*
-	 * Read data port to reset things, and then unlink from
-	 * the IRQ chain.
-	 */
-	serial_port_in(port, UART_RX);
-	serial8250_rpm_put(up);
-
-	up->ops->release_irq(up);
-}
-EXPORT_SYMBOL_GPL(serial8250_do_shutdown);
-
-static void serial8250_shutdown(struct uart_port *port)
-{
-	if (port->shutdown)
-		port->shutdown(port);
-	else
-		serial8250_do_shutdown(port);
-}
-
-/*
- * XR17V35x UARTs have an extra fractional divisor register (DLD)
- * Calculate divisor with extra 4-bit fractional portion
- */
-static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up,
-					 unsigned int baud,
-					 unsigned int *frac)
-{
-	struct uart_port *port = &up->port;
-	unsigned int quot_16;
-
-	quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud);
-	*frac = quot_16 & 0x0f;
-
-	return quot_16 >> 4;
-}
-
-static unsigned int serial8250_get_divisor(struct uart_8250_port *up,
-					   unsigned int baud,
-					   unsigned int *frac)
-{
-	struct uart_port *port = &up->port;
-	unsigned int quot;
-
-	/*
-	 * Handle magic divisors for baud rates above baud_base on
-	 * SMSC SuperIO chips.
-	 *
-	 */
-	if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
-	    baud == (port->uartclk/4))
-		quot = 0x8001;
-	else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
-		 baud == (port->uartclk/8))
-		quot = 0x8002;
-	else if (up->port.type == PORT_XR17V35X)
-		quot = xr17v35x_get_divisor(up, baud, frac);
-	else
-		quot = uart_get_divisor(port, baud);
-
-	/*
-	 * Oxford Semi 952 rev B workaround
-	 */
-	if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
-		quot++;
-
-	return quot;
-}
-
-static unsigned char serial8250_compute_lcr(struct uart_8250_port *up,
-					    tcflag_t c_cflag)
-{
-	unsigned char cval;
-
-	switch (c_cflag & CSIZE) {
-	case CS5:
-		cval = UART_LCR_WLEN5;
-		break;
-	case CS6:
-		cval = UART_LCR_WLEN6;
-		break;
-	case CS7:
-		cval = UART_LCR_WLEN7;
-		break;
-	default:
-	case CS8:
-		cval = UART_LCR_WLEN8;
-		break;
-	}
-
-	if (c_cflag & CSTOPB)
-		cval |= UART_LCR_STOP;
-	if (c_cflag & PARENB) {
-		cval |= UART_LCR_PARITY;
-		if (up->bugs & UART_BUG_PARITY)
-			up->fifo_bug = true;
-	}
-	if (!(c_cflag & PARODD))
-		cval |= UART_LCR_EPAR;
-#ifdef CMSPAR
-	if (c_cflag & CMSPAR)
-		cval |= UART_LCR_SPAR;
-#endif
-
-	return cval;
-}
-
-static void serial8250_set_divisor(struct uart_port *port, unsigned int baud,
-			    unsigned int quot, unsigned int quot_frac)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	/* Workaround to enable 115200 baud on OMAP1510 internal ports */
-	if (is_omap1510_8250(up)) {
-		if (baud == 115200) {
-			quot = 1;
-			serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1);
-		} else
-			serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0);
-	}
-
-	/*
-	 * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2,
-	 * otherwise just set DLAB
-	 */
-	if (up->capabilities & UART_NATSEMI)
-		serial_port_out(port, UART_LCR, 0xe0);
-	else
-		serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
-
-	serial_dl_write(up, quot);
-
-	/* XR17V35x UARTs have an extra fractional divisor register (DLD) */
-	if (up->port.type == PORT_XR17V35X)
-		serial_port_out(port, 0x2, quot_frac);
-}
-
-void
-serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
-		          struct ktermios *old)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	unsigned char cval;
-	unsigned long flags;
-	unsigned int baud, quot, frac = 0;
-
-	cval = serial8250_compute_lcr(up, termios->c_cflag);
-
-	/*
-	 * Ask the core to calculate the divisor for us.
-	 */
-	baud = uart_get_baud_rate(port, termios, old,
-				  port->uartclk / 16 / 0xffff,
-				  port->uartclk / 16);
-	quot = serial8250_get_divisor(up, baud, &frac);
-
-	/*
-	 * Ok, we're now changing the port state.  Do it with
-	 * interrupts disabled.
-	 */
-	serial8250_rpm_get(up);
-	spin_lock_irqsave(&port->lock, flags);
-
-	up->lcr = cval;					/* Save computed LCR */
-
-	if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
-		/* NOTE: If fifo_bug is not set, a user can set RX_trigger. */
-		if ((baud < 2400 && !up->dma) || up->fifo_bug) {
-			up->fcr &= ~UART_FCR_TRIGGER_MASK;
-			up->fcr |= UART_FCR_TRIGGER_1;
-		}
-	}
-
-	/*
-	 * MCR-based auto flow control.  When AFE is enabled, RTS will be
-	 * deasserted when the receive FIFO contains more characters than
-	 * the trigger, or the MCR RTS bit is cleared.  In the case where
-	 * the remote UART is not using CTS auto flow control, we must
-	 * have sufficient FIFO entries for the latency of the remote
-	 * UART to respond.  IOW, at least 32 bytes of FIFO.
-	 */
-	if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) {
-		up->mcr &= ~UART_MCR_AFE;
-		if (termios->c_cflag & CRTSCTS)
-			up->mcr |= UART_MCR_AFE;
-	}
-
-	/*
-	 * Update the per-port timeout.
-	 */
-	uart_update_timeout(port, termios->c_cflag, baud);
-
-	port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
-	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
-	if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
-		port->read_status_mask |= UART_LSR_BI;
-
-	/*
-	 * Characteres to ignore
-	 */
-	port->ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
-	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= UART_LSR_BI;
-		/*
-		 * If we're ignoring parity and break indicators,
-		 * ignore overruns too (for real raw support).
-		 */
-		if (termios->c_iflag & IGNPAR)
-			port->ignore_status_mask |= UART_LSR_OE;
-	}
-
-	/*
-	 * ignore all characters if CREAD is not set
-	 */
-	if ((termios->c_cflag & CREAD) == 0)
-		port->ignore_status_mask |= UART_LSR_DR;
-
-	/*
-	 * CTS flow control flag and modem status interrupts
-	 */
-	up->ier &= ~UART_IER_MSI;
-	if (!(up->bugs & UART_BUG_NOMSR) &&
-			UART_ENABLE_MS(&up->port, termios->c_cflag))
-		up->ier |= UART_IER_MSI;
-	if (up->capabilities & UART_CAP_UUE)
-		up->ier |= UART_IER_UUE;
-	if (up->capabilities & UART_CAP_RTOIE)
-		up->ier |= UART_IER_RTOIE;
-
-	serial_port_out(port, UART_IER, up->ier);
-
-	if (up->capabilities & UART_CAP_EFR) {
-		unsigned char efr = 0;
-		/*
-		 * TI16C752/Startech hardware flow control.  FIXME:
-		 * - TI16C752 requires control thresholds to be set.
-		 * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled.
-		 */
-		if (termios->c_cflag & CRTSCTS)
-			efr |= UART_EFR_CTS;
-
-		serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
-		if (port->flags & UPF_EXAR_EFR)
-			serial_port_out(port, UART_XR_EFR, efr);
-		else
-			serial_port_out(port, UART_EFR, efr);
-	}
-
-	serial8250_set_divisor(port, baud, quot, frac);
-
-	/*
-	 * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
-	 * is written without DLAB set, this mode will be disabled.
-	 */
-	if (port->type == PORT_16750)
-		serial_port_out(port, UART_FCR, up->fcr);
-
-	serial_port_out(port, UART_LCR, up->lcr);	/* reset DLAB */
-	if (port->type != PORT_16750) {
-		/* emulated UARTs (Lucent Venus 167x) need two steps */
-		if (up->fcr & UART_FCR_ENABLE_FIFO)
-			serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO);
-		serial_port_out(port, UART_FCR, up->fcr);	/* set fcr */
-	}
-	serial8250_set_mctrl(port, port->mctrl);
-	spin_unlock_irqrestore(&port->lock, flags);
-	serial8250_rpm_put(up);
-
-	/* Don't rewrite B0 */
-	if (tty_termios_baud_rate(termios))
-		tty_termios_encode_baud_rate(termios, baud, baud);
-}
-EXPORT_SYMBOL(serial8250_do_set_termios);
-
-static void
-serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
-		       struct ktermios *old)
-{
-	if (port->set_termios)
-		port->set_termios(port, termios, old);
-	else
-		serial8250_do_set_termios(port, termios, old);
-}
-
-static void
-serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios)
-{
-	if (termios->c_line == N_PPS) {
-		port->flags |= UPF_HARDPPS_CD;
-		spin_lock_irq(&port->lock);
-		serial8250_enable_ms(port);
-		spin_unlock_irq(&port->lock);
-	} else {
-		port->flags &= ~UPF_HARDPPS_CD;
-		if (!UART_ENABLE_MS(port, termios->c_cflag)) {
-			spin_lock_irq(&port->lock);
-			serial8250_disable_ms(port);
-			spin_unlock_irq(&port->lock);
-		}
-	}
-}
-
-
-void serial8250_do_pm(struct uart_port *port, unsigned int state,
-		      unsigned int oldstate)
-{
-	struct uart_8250_port *p = up_to_u8250p(port);
-
-	serial8250_set_sleep(p, state != 0);
-}
-EXPORT_SYMBOL(serial8250_do_pm);
-
-static void
-serial8250_pm(struct uart_port *port, unsigned int state,
-	      unsigned int oldstate)
-{
-	if (port->pm)
-		port->pm(port, state, oldstate);
-	else
-		serial8250_do_pm(port, state, oldstate);
-}
-
-static unsigned int serial8250_port_size(struct uart_8250_port *pt)
-{
-	if (pt->port.mapsize)
-		return pt->port.mapsize;
-	if (pt->port.iotype == UPIO_AU) {
-		if (pt->port.type == PORT_RT2880)
-			return 0x100;
-		return 0x1000;
-	}
-	if (is_omap1_8250(pt))
-		return 0x16 << pt->port.regshift;
-
-	return 8 << pt->port.regshift;
-}
-
-/*
- * Resource handling.
- */
-static int serial8250_request_std_resource(struct uart_8250_port *up)
-{
-	unsigned int size = serial8250_port_size(up);
-	struct uart_port *port = &up->port;
-	int ret = 0;
-
-	switch (port->iotype) {
-	case UPIO_AU:
-	case UPIO_TSI:
-	case UPIO_MEM32:
-	case UPIO_MEM32BE:
-	case UPIO_MEM:
-		if (!port->mapbase)
-			break;
-
-		if (!request_mem_region(port->mapbase, size, "serial")) {
-			ret = -EBUSY;
-			break;
-		}
-
-		if (port->flags & UPF_IOREMAP) {
-			port->membase = ioremap_nocache(port->mapbase, size);
-			if (!port->membase) {
-				release_mem_region(port->mapbase, size);
-				ret = -ENOMEM;
-			}
-		}
-		break;
-
-	case UPIO_HUB6:
-	case UPIO_PORT:
-		if (!request_region(port->iobase, size, "serial"))
-			ret = -EBUSY;
-		break;
-	}
-	return ret;
-}
-
-static void serial8250_release_std_resource(struct uart_8250_port *up)
-{
-	unsigned int size = serial8250_port_size(up);
-	struct uart_port *port = &up->port;
-
-	switch (port->iotype) {
-	case UPIO_AU:
-	case UPIO_TSI:
-	case UPIO_MEM32:
-	case UPIO_MEM32BE:
-	case UPIO_MEM:
-		if (!port->mapbase)
-			break;
-
-		if (port->flags & UPF_IOREMAP) {
-			iounmap(port->membase);
-			port->membase = NULL;
-		}
-
-		release_mem_region(port->mapbase, size);
-		break;
-
-	case UPIO_HUB6:
-	case UPIO_PORT:
-		release_region(port->iobase, size);
-		break;
-	}
-}
-
 #ifdef CONFIG_SERIAL_8250_RSA
 static int serial8250_request_rsa_resource(struct uart_8250_port *up)
 {
@@ -2870,259 +405,6 @@ static void serial8250_release_rsa_resource(struct uart_8250_port *up)
 }
 #endif
 
-static void serial8250_release_port(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	serial8250_release_std_resource(up);
-}
-
-static int serial8250_request_port(struct uart_port *port)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	int ret;
-
-	if (port->type == PORT_8250_CIR)
-		return -ENODEV;
-
-	ret = serial8250_request_std_resource(up);
-
-	return ret;
-}
-
-static int fcr_get_rxtrig_bytes(struct uart_8250_port *up)
-{
-	const struct serial8250_config *conf_type = &uart_config[up->port.type];
-	unsigned char bytes;
-
-	bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)];
-
-	return bytes ? bytes : -EOPNOTSUPP;
-}
-
-static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes)
-{
-	const struct serial8250_config *conf_type = &uart_config[up->port.type];
-	int i;
-
-	if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)])
-		return -EOPNOTSUPP;
-
-	for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) {
-		if (bytes < conf_type->rxtrig_bytes[i])
-			/* Use the nearest lower value */
-			return (--i) << UART_FCR_R_TRIG_SHIFT;
-	}
-
-	return UART_FCR_R_TRIG_11;
-}
-
-static int do_get_rxtrig(struct tty_port *port)
-{
-	struct uart_state *state = container_of(port, struct uart_state, port);
-	struct uart_port *uport = state->uart_port;
-	struct uart_8250_port *up =
-		container_of(uport, struct uart_8250_port, port);
-
-	if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1)
-		return -EINVAL;
-
-	return fcr_get_rxtrig_bytes(up);
-}
-
-static int do_serial8250_get_rxtrig(struct tty_port *port)
-{
-	int rxtrig_bytes;
-
-	mutex_lock(&port->mutex);
-	rxtrig_bytes = do_get_rxtrig(port);
-	mutex_unlock(&port->mutex);
-
-	return rxtrig_bytes;
-}
-
-static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev,
-	struct device_attribute *attr, char *buf)
-{
-	struct tty_port *port = dev_get_drvdata(dev);
-	int rxtrig_bytes;
-
-	rxtrig_bytes = do_serial8250_get_rxtrig(port);
-	if (rxtrig_bytes < 0)
-		return rxtrig_bytes;
-
-	return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes);
-}
-
-static int do_set_rxtrig(struct tty_port *port, unsigned char bytes)
-{
-	struct uart_state *state = container_of(port, struct uart_state, port);
-	struct uart_port *uport = state->uart_port;
-	struct uart_8250_port *up =
-		container_of(uport, struct uart_8250_port, port);
-	int rxtrig;
-
-	if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 ||
-	    up->fifo_bug)
-		return -EINVAL;
-
-	rxtrig = bytes_to_fcr_rxtrig(up, bytes);
-	if (rxtrig < 0)
-		return rxtrig;
-
-	serial8250_clear_fifos(up);
-	up->fcr &= ~UART_FCR_TRIGGER_MASK;
-	up->fcr |= (unsigned char)rxtrig;
-	serial_out(up, UART_FCR, up->fcr);
-	return 0;
-}
-
-static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes)
-{
-	int ret;
-
-	mutex_lock(&port->mutex);
-	ret = do_set_rxtrig(port, bytes);
-	mutex_unlock(&port->mutex);
-
-	return ret;
-}
-
-static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev,
-	struct device_attribute *attr, const char *buf, size_t count)
-{
-	struct tty_port *port = dev_get_drvdata(dev);
-	unsigned char bytes;
-	int ret;
-
-	if (!count)
-		return -EINVAL;
-
-	ret = kstrtou8(buf, 10, &bytes);
-	if (ret < 0)
-		return ret;
-
-	ret = do_serial8250_set_rxtrig(port, bytes);
-	if (ret < 0)
-		return ret;
-
-	return count;
-}
-
-static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP,
-		   serial8250_get_attr_rx_trig_bytes,
-		   serial8250_set_attr_rx_trig_bytes);
-
-static struct attribute *serial8250_dev_attrs[] = {
-	&dev_attr_rx_trig_bytes.attr,
-	NULL,
-	};
-
-static struct attribute_group serial8250_dev_attr_group = {
-	.attrs = serial8250_dev_attrs,
-	};
-
-static void register_dev_spec_attr_grp(struct uart_8250_port *up)
-{
-	const struct serial8250_config *conf_type = &uart_config[up->port.type];
-
-	if (conf_type->rxtrig_bytes[0])
-		up->port.attr_group = &serial8250_dev_attr_group;
-}
-
-static void serial8250_config_port(struct uart_port *port, int flags)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-	int ret;
-
-	if (port->type == PORT_8250_CIR)
-		return;
-
-	/*
-	 * Find the region that we can probe for.  This in turn
-	 * tells us whether we can probe for the type of port.
-	 */
-	ret = serial8250_request_std_resource(up);
-	if (ret < 0)
-		return;
-
-	if (port->iotype != up->cur_iotype)
-		set_io_from_upio(port);
-
-	if (flags & UART_CONFIG_TYPE)
-		autoconfig(up);
-
-	/* if access method is AU, it is a 16550 with a quirk */
-	if (port->type == PORT_16550A && port->iotype == UPIO_AU)
-		up->bugs |= UART_BUG_NOMSR;
-
-	/* HW bugs may trigger IRQ while IIR == NO_INT */
-	if (port->type == PORT_TEGRA)
-		up->bugs |= UART_BUG_NOMSR;
-
-	if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
-		autoconfig_irq(up);
-
-	if (port->type == PORT_UNKNOWN)
-		serial8250_release_std_resource(up);
-
-	/* Fixme: probably not the best place for this */
-	if ((port->type == PORT_XR17V35X) ||
-	   (port->type == PORT_XR17D15X))
-		port->handle_irq = exar_handle_irq;
-
-	register_dev_spec_attr_grp(up);
-	up->fcr = uart_config[up->port.type].fcr;
-}
-
-static int
-serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
-	if (ser->irq >= nr_irqs || ser->irq < 0 ||
-	    ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
-	    ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS ||
-	    ser->type == PORT_STARTECH)
-		return -EINVAL;
-	return 0;
-}
-
-static const char *
-serial8250_type(struct uart_port *port)
-{
-	int type = port->type;
-
-	if (type >= ARRAY_SIZE(uart_config))
-		type = 0;
-	return uart_config[type].name;
-}
-
-static const struct uart_ops serial8250_pops = {
-	.tx_empty	= serial8250_tx_empty,
-	.set_mctrl	= serial8250_set_mctrl,
-	.get_mctrl	= serial8250_get_mctrl,
-	.stop_tx	= serial8250_stop_tx,
-	.start_tx	= serial8250_start_tx,
-	.throttle	= serial8250_throttle,
-	.unthrottle	= serial8250_unthrottle,
-	.stop_rx	= serial8250_stop_rx,
-	.enable_ms	= serial8250_enable_ms,
-	.break_ctl	= serial8250_break_ctl,
-	.startup	= serial8250_startup,
-	.shutdown	= serial8250_shutdown,
-	.set_termios	= serial8250_set_termios,
-	.set_ldisc	= serial8250_set_ldisc,
-	.pm		= serial8250_pm,
-	.type		= serial8250_type,
-	.release_port	= serial8250_release_port,
-	.request_port	= serial8250_request_port,
-	.config_port	= serial8250_config_port,
-	.verify_port	= serial8250_verify_port,
-#ifdef CONFIG_CONSOLE_POLL
-	.poll_get_char = serial8250_get_poll_char,
-	.poll_put_char = serial8250_put_poll_char,
-#endif
-};
-
 static const struct uart_ops *base_ops;
 static struct uart_ops univ8250_port_ops;
 
@@ -3161,42 +443,6 @@ void serial8250_set_isa_configurator(
 }
 EXPORT_SYMBOL(serial8250_set_isa_configurator);
 
-static void serial8250_init_port(struct uart_8250_port *up)
-{
-	struct uart_port *port = &up->port;
-
-	spin_lock_init(&port->lock);
-	port->ops = &serial8250_pops;
-
-	up->cur_iotype = 0xFF;
-}
-
-static void serial8250_set_defaults(struct uart_8250_port *up)
-{
-	struct uart_port *port = &up->port;
-
-	if (up->port.flags & UPF_FIXED_TYPE) {
-		unsigned int type = up->port.type;
-
-		if (!up->port.fifosize)
-			up->port.fifosize = uart_config[type].fifo_size;
-		if (!up->tx_loadsz)
-			up->tx_loadsz = uart_config[type].tx_loadsz;
-		if (!up->capabilities)
-			up->capabilities = uart_config[type].flags;
-	}
-
-	set_io_from_upio(port);
-
-	/* default dma handlers */
-	if (up->dma) {
-		if (!up->dma->tx_dma)
-			up->dma->tx_dma = serial8250_tx_dma;
-		if (!up->dma->rx_dma)
-			up->dma->rx_dma = serial8250_rx_dma;
-	}
-}
-
 #ifdef CONFIG_SERIAL_8250_RSA
 
 static void univ8250_config_port(struct uart_port *port, int flags)
@@ -3332,6 +578,9 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
 	for (i = 0; i < nr_uarts; i++) {
 		struct uart_8250_port *up = &serial8250_ports[i];
 
+		if (up->port.type == PORT_8250_CIR)
+			continue;
+
 		if (up->port.dev)
 			continue;
 
@@ -3346,94 +595,6 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
 
-static void serial8250_console_putchar(struct uart_port *port, int ch)
-{
-	struct uart_8250_port *up = up_to_u8250p(port);
-
-	wait_for_xmitr(up, UART_LSR_THRE);
-	serial_port_out(port, UART_TX, ch);
-}
-
-/*
- *	Print a string to the serial port trying not to disturb
- *	any possible real use of the port...
- *
- *	The console_lock must be held when we get here.
- */
-static void serial8250_console_write(struct uart_8250_port *up, const char *s,
-				     unsigned int count)
-{
-	struct uart_port *port = &up->port;
-	unsigned long flags;
-	unsigned int ier;
-	int locked = 1;
-
-	touch_nmi_watchdog();
-
-	serial8250_rpm_get(up);
-
-	if (port->sysrq)
-		locked = 0;
-	else if (oops_in_progress || in_kdb_printk())
-		locked = spin_trylock_irqsave(&port->lock, flags);
-	else
-		spin_lock_irqsave(&port->lock, flags);
-
-	/*
-	 *	First save the IER then disable the interrupts
-	 */
-	ier = serial_port_in(port, UART_IER);
-
-	if (up->capabilities & UART_CAP_UUE)
-		serial_port_out(port, UART_IER, UART_IER_UUE);
-	else
-		serial_port_out(port, UART_IER, 0);
-
-	/* check scratch reg to see if port powered off during system sleep */
-	if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
-		struct ktermios termios;
-		unsigned int baud, quot, frac = 0;
-
-		termios.c_cflag = port->cons->cflag;
-		if (port->state->port.tty && termios.c_cflag == 0)
-			termios.c_cflag = port->state->port.tty->termios.c_cflag;
-
-		baud = uart_get_baud_rate(port, &termios, NULL,
-					  port->uartclk / 16 / 0xffff,
-					  port->uartclk / 16);
-		quot = serial8250_get_divisor(up, baud, &frac);
-
-		serial8250_set_divisor(port, baud, quot, frac);
-		serial_port_out(port, UART_LCR, up->lcr);
-		serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
-
-		up->canary = 0;
-	}
-
-	uart_console_write(port, s, count, serial8250_console_putchar);
-
-	/*
-	 *	Finally, wait for transmitter to become empty
-	 *	and restore the IER
-	 */
-	wait_for_xmitr(up, BOTH_EMPTY);
-	serial_port_out(port, UART_IER, ier);
-
-	/*
-	 *	The receive handling will happen properly because the
-	 *	receive ready bit will still be set; it is not cleared
-	 *	on read.  However, modem control will not, we must
-	 *	call it if we have saved something in the saved flags
-	 *	while processing with interrupts off.
-	 */
-	if (up->msr_saved_flags)
-		serial8250_modem_status(up);
-
-	if (locked)
-		spin_unlock_irqrestore(&port->lock, flags);
-	serial8250_rpm_put(up);
-}
-
 static void univ8250_console_write(struct console *co, const char *s,
 				   unsigned int count)
 {
@@ -3442,39 +603,6 @@ static void univ8250_console_write(struct console *co, const char *s,
 	serial8250_console_write(up, s, count);
 }
 
-static unsigned int probe_baud(struct uart_port *port)
-{
-	unsigned char lcr, dll, dlm;
-	unsigned int quot;
-
-	lcr = serial_port_in(port, UART_LCR);
-	serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB);
-	dll = serial_port_in(port, UART_DLL);
-	dlm = serial_port_in(port, UART_DLM);
-	serial_port_out(port, UART_LCR, lcr);
-
-	quot = (dlm << 8) | dll;
-	return (port->uartclk / 16) / quot;
-}
-
-static int serial8250_console_setup(struct uart_port *port, char *options, bool probe)
-{
-	int baud = 9600;
-	int bits = 8;
-	int parity = 'n';
-	int flow = 'n';
-
-	if (!port->iobase && !port->membase)
-		return -ENODEV;
-
-	if (options)
-		uart_parse_options(options, &baud, &parity, &bits, &flow);
-	else if (probe)
-		baud = probe_baud(port);
-
-	return uart_set_options(port, port->cons, baud, parity, bits, flow);
-}
-
 static int univ8250_console_setup(struct console *co, char *options)
 {
 	struct uart_port *port;
@@ -3558,6 +686,9 @@ static struct console univ8250_console = {
 
 static int __init univ8250_console_init(void)
 {
+	if (nr_uarts == 0)
+		return -ENODEV;
+
 	serial8250_isa_init_ports();
 	register_console(&univ8250_console);
 	return 0;
@@ -3588,7 +719,7 @@ int __init early_serial_setup(struct uart_port *port)
 {
 	struct uart_port *p;
 
-	if (port->line >= ARRAY_SIZE(serial8250_ports))
+	if (port->line >= ARRAY_SIZE(serial8250_ports) || nr_uarts == 0)
 		return -ENODEV;
 
 	serial8250_isa_init_ports();
@@ -3860,7 +991,6 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
 		uart->port.mapbase      = up->port.mapbase;
 		uart->port.mapsize      = up->port.mapsize;
 		uart->port.private_data = up->port.private_data;
-		uart->port.fifosize	= up->port.fifosize;
 		uart->tx_loadsz		= up->tx_loadsz;
 		uart->capabilities	= up->capabilities;
 		uart->port.throttle	= up->port.throttle;
@@ -3909,13 +1039,24 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
 		if (up->dl_write)
 			uart->dl_write = up->dl_write;
 
-		if (serial8250_isa_config != NULL)
-			serial8250_isa_config(0, &uart->port,
-					&uart->capabilities);
+		if (uart->port.type != PORT_8250_CIR) {
+			if (serial8250_isa_config != NULL)
+				serial8250_isa_config(0, &uart->port,
+						&uart->capabilities);
+
+			ret = uart_add_one_port(&serial8250_reg,
+						&uart->port);
+			if (ret == 0)
+				ret = uart->port.line;
+		} else {
+			dev_info(uart->port.dev,
+				"skipping CIR port at 0x%lx / 0x%llx, IRQ %d\n",
+				uart->port.iobase,
+				(unsigned long long)uart->port.mapbase,
+				uart->port.irq);
 
-		ret = uart_add_one_port(&serial8250_reg, &uart->port);
-		if (ret == 0)
-			ret = uart->port.line;
+			ret = 0;
+		}
 	}
 	mutex_unlock(&serial_mutex);
 
@@ -3955,6 +1096,9 @@ static int __init serial8250_init(void)
 {
 	int ret;
 
+	if (nr_uarts == 0)
+		return -ENODEV;
+
 	serial8250_isa_init_ports();
 
 	printk(KERN_INFO "Serial: 8250/16550 driver, "
diff --git a/kernel/drivers/tty/serial/8250/8250_dma.c b/kernel/drivers/tty/serial/8250/8250_dma.c
index 21d01a491..78259d3c6 100644
--- a/kernel/drivers/tty/serial/8250/8250_dma.c
+++ b/kernel/drivers/tty/serial/8250/8250_dma.c
@@ -54,9 +54,6 @@ static void __dma_rx_complete(void *param)
 	struct dma_tx_state	state;
 	int			count;
 
-	dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr,
-				dma->rx_size, DMA_FROM_DEVICE);
-
 	dma->rx_running = 0;
 	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
 
@@ -80,10 +77,6 @@ int serial8250_tx_dma(struct uart_8250_port *p)
 		return 0;
 
 	dma->tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
-	if (dma->tx_size < p->port.fifosize) {
-		ret = -EINVAL;
-		goto err;
-	}
 
 	desc = dmaengine_prep_slave_single(dma->txchan,
 					   dma->tx_addr + xmit->tail,
@@ -156,9 +149,6 @@ int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 
 	dma->rx_cookie = dmaengine_submit(desc);
 
-	dma_sync_single_for_device(dma->rxchan->device->dev, dma->rx_addr,
-				   dma->rx_size, DMA_FROM_DEVICE);
-
 	dma_async_issue_pending(dma->rxchan);
 
 	return 0;
diff --git a/kernel/drivers/tty/serial/8250/8250_dw.c b/kernel/drivers/tty/serial/8250/8250_dw.c
index 176f18f2e..a5d319e4a 100644
--- a/kernel/drivers/tty/serial/8250/8250_dw.c
+++ b/kernel/drivers/tty/serial/8250/8250_dw.c
@@ -56,7 +56,6 @@
 
 struct dw8250_data {
 	u8			usr_reg;
-	int			last_mcr;
 	int			line;
 	int			msr_mask_on;
 	int			msr_mask_off;
@@ -64,6 +63,9 @@ struct dw8250_data {
 	struct clk		*pclk;
 	struct reset_control	*rst;
 	struct uart_8250_dma	dma;
+
+	unsigned int		skip_autocfg:1;
+	unsigned int		uart_16550_compatible:1;
 };
 
 #define BYT_PRV_CLK			0x800
@@ -76,12 +78,6 @@ static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value)
 {
 	struct dw8250_data *d = p->private_data;
 
-	/* If reading MSR, report CTS asserted when auto-CTS/RTS enabled */
-	if (offset == UART_MSR && d->last_mcr & UART_MCR_AFE) {
-		value |= UART_MSR_CTS;
-		value &= ~UART_MSR_DCTS;
-	}
-
 	/* Override any modem control signals if needed */
 	if (offset == UART_MSR) {
 		value |= d->msr_mask_on;
@@ -101,11 +97,6 @@ static void dw8250_force_idle(struct uart_port *p)
 
 static void dw8250_serial_out(struct uart_port *p, int offset, int value)
 {
-	struct dw8250_data *d = p->private_data;
-
-	if (offset == UART_MCR)
-		d->last_mcr = value;
-
 	writeb(value, p->membase + (offset << p->regshift));
 
 	/* Make sure LCR write wasn't ignored */
@@ -144,11 +135,6 @@ static unsigned int dw8250_serial_inq(struct uart_port *p, int offset)
 
 static void dw8250_serial_outq(struct uart_port *p, int offset, int value)
 {
-	struct dw8250_data *d = p->private_data;
-
-	if (offset == UART_MCR)
-		d->last_mcr = value;
-
 	value &= 0xff;
 	__raw_writeq(value, p->membase + (offset << p->regshift));
 	/* Read back to ensure register write ordering. */
@@ -175,11 +161,6 @@ static void dw8250_serial_outq(struct uart_port *p, int offset, int value)
 
 static void dw8250_serial_out32(struct uart_port *p, int offset, int value)
 {
-	struct dw8250_data *d = p->private_data;
-
-	if (offset == UART_MCR)
-		d->last_mcr = value;
-
 	writel(value, p->membase + (offset << p->regshift));
 
 	/* Make sure LCR write wasn't ignored */
@@ -246,10 +227,6 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios,
 	if (IS_ERR(d->clk) || !old)
 		goto out;
 
-	/* Not requesting clock rates below 1.8432Mhz */
-	if (baud < 115200)
-		baud = 115200;
-
 	clk_disable_unprepare(d->clk);
 	rate = clk_round_rate(d->clk, baud * 16);
 	ret = clk_set_rate(d->clk, rate);
@@ -257,28 +234,86 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios,
 
 	if (!ret)
 		p->uartclk = rate;
+
+	p->status &= ~UPSTAT_AUTOCTS;
+	if (termios->c_cflag & CRTSCTS)
+		p->status |= UPSTAT_AUTOCTS;
+
 out:
 	serial8250_do_set_termios(p, termios, old);
 }
 
-static bool dw8250_dma_filter(struct dma_chan *chan, void *param)
+/*
+ * dw8250_fallback_dma_filter will prevent the UART from getting just any free
+ * channel on platforms that have DMA engines, but don't have any channels
+ * assigned to the UART.
+ *
+ * REVISIT: This is a work around for limitation in the DMA Engine API. Once the
+ * core problem is fixed, this function is no longer needed.
+ */
+static bool dw8250_fallback_dma_filter(struct dma_chan *chan, void *param)
 {
 	return false;
 }
 
-static void dw8250_setup_port(struct uart_8250_port *up)
+static bool dw8250_idma_filter(struct dma_chan *chan, void *param)
 {
-	struct uart_port	*p = &up->port;
-	u32			reg = readl(p->membase + DW_UART_UCV);
+	return param == chan->device->dev->parent;
+}
+
+static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
+{
+	if (p->dev->of_node) {
+		struct device_node *np = p->dev->of_node;
+		int id;
+
+		/* get index of serial line, if found in DT aliases */
+		id = of_alias_get_id(np, "serial");
+		if (id >= 0)
+			p->line = id;
+#ifdef CONFIG_64BIT
+		if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) {
+			p->serial_in = dw8250_serial_inq;
+			p->serial_out = dw8250_serial_outq;
+			p->flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
+			p->type = PORT_OCTEON;
+			data->usr_reg = 0x27;
+			data->skip_autocfg = true;
+		}
+#endif
+	} else if (has_acpi_companion(p->dev)) {
+		p->iotype = UPIO_MEM32;
+		p->regshift = 2;
+		p->serial_in = dw8250_serial_in32;
+		p->set_termios = dw8250_set_termios;
+		/* So far none of there implement the Busy Functionality */
+		data->uart_16550_compatible = true;
+	}
+
+	/* Platforms with iDMA */
+	if (platform_get_resource_byname(to_platform_device(p->dev),
+					 IORESOURCE_MEM, "lpss_priv")) {
+		p->set_termios = dw8250_set_termios;
+		data->dma.rx_param = p->dev->parent;
+		data->dma.tx_param = p->dev->parent;
+		data->dma.fn = dw8250_idma_filter;
+	}
+}
+
+static void dw8250_setup_port(struct uart_port *p)
+{
+	struct uart_8250_port *up = up_to_u8250p(p);
+	u32 reg;
 
 	/*
 	 * If the Component Version Register returns zero, we know that
 	 * ADDITIONAL_FEATURES are not enabled. No need to go any further.
 	 */
+	reg = readl(p->membase + DW_UART_UCV);
 	if (!reg)
 		return;
 
-	dev_dbg_ratelimited(p->dev, "Designware UART version %c.%c%c\n",
+	dev_dbg(p->dev, "Designware UART version %c.%c%c\n",
 		(reg >> 24) & 0xff, (reg >> 16) & 0xff, (reg >> 8) & 0xff);
 
 	reg = readl(p->membase + DW_UART_CPR);
@@ -290,7 +325,6 @@ static void dw8250_setup_port(struct uart_8250_port *up)
 		p->type = PORT_16550A;
 		p->flags |= UPF_FIXED_TYPE;
 		p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
-		up->tx_loadsz = p->fifosize;
 		up->capabilities = UART_CAP_FIFO;
 	}
 
@@ -298,149 +332,91 @@ static void dw8250_setup_port(struct uart_8250_port *up)
 		up->capabilities |= UART_CAP_AFE;
 }
 
-static int dw8250_probe_of(struct uart_port *p,
-			   struct dw8250_data *data)
+static int dw8250_probe(struct platform_device *pdev)
 {
-	struct device_node	*np = p->dev->of_node;
-	struct uart_8250_port *up = up_to_u8250p(p);
-	u32			val;
-	bool has_ucv = true;
-	int id;
+	struct uart_8250_port uart = {};
+	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	int irq = platform_get_irq(pdev, 0);
+	struct uart_port *p = &uart.port;
+	struct dw8250_data *data;
+	int err;
+	u32 val;
 
-#ifdef CONFIG_64BIT
-	if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) {
-		p->serial_in = dw8250_serial_inq;
-		p->serial_out = dw8250_serial_outq;
-		p->flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
-		p->type = PORT_OCTEON;
-		data->usr_reg = 0x27;
-		has_ucv = false;
-	} else
-#endif
-	if (!of_property_read_u32(np, "reg-io-width", &val)) {
-		switch (val) {
-		case 1:
-			break;
-		case 4:
-			p->iotype = UPIO_MEM32;
-			p->serial_in = dw8250_serial_in32;
-			p->serial_out = dw8250_serial_out32;
-			break;
-		default:
-			dev_err(p->dev, "unsupported reg-io-width (%u)\n", val);
-			return -EINVAL;
-		}
+	if (!regs) {
+		dev_err(&pdev->dev, "no registers defined\n");
+		return -EINVAL;
 	}
-	if (has_ucv)
-		dw8250_setup_port(up);
 
-	/* if we have a valid fifosize, try hooking up DMA here */
-	if (p->fifosize) {
-		up->dma = &data->dma;
-
-		up->dma->rxconf.src_maxburst = p->fifosize / 4;
-		up->dma->txconf.dst_maxburst = p->fifosize / 4;
+	if (irq < 0) {
+		if (irq != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "cannot get irq\n");
+		return irq;
 	}
 
-	if (!of_property_read_u32(np, "reg-shift", &val))
+	spin_lock_init(&p->lock);
+	p->mapbase	= regs->start;
+	p->irq		= irq;
+	p->handle_irq	= dw8250_handle_irq;
+	p->pm		= dw8250_do_pm;
+	p->type		= PORT_8250;
+	p->flags	= UPF_SHARE_IRQ | UPF_FIXED_PORT;
+	p->dev		= &pdev->dev;
+	p->iotype	= UPIO_MEM;
+	p->serial_in	= dw8250_serial_in;
+	p->serial_out	= dw8250_serial_out;
+
+	p->membase = devm_ioremap(&pdev->dev, regs->start, resource_size(regs));
+	if (!p->membase)
+		return -ENOMEM;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->dma.fn = dw8250_fallback_dma_filter;
+	data->usr_reg = DW_UART_USR;
+	p->private_data = data;
+
+	data->uart_16550_compatible = device_property_read_bool(p->dev,
+						"snps,uart-16550-compatible");
+
+	err = device_property_read_u32(p->dev, "reg-shift", &val);
+	if (!err)
 		p->regshift = val;
 
-	/* get index of serial line, if found in DT aliases */
-	id = of_alias_get_id(np, "serial");
-	if (id >= 0)
-		p->line = id;
+	err = device_property_read_u32(p->dev, "reg-io-width", &val);
+	if (!err && val == 4) {
+		p->iotype = UPIO_MEM32;
+		p->serial_in = dw8250_serial_in32;
+		p->serial_out = dw8250_serial_out32;
+	}
 
-	if (of_property_read_bool(np, "dcd-override")) {
+	if (device_property_read_bool(p->dev, "dcd-override")) {
 		/* Always report DCD as active */
 		data->msr_mask_on |= UART_MSR_DCD;
 		data->msr_mask_off |= UART_MSR_DDCD;
 	}
 
-	if (of_property_read_bool(np, "dsr-override")) {
+	if (device_property_read_bool(p->dev, "dsr-override")) {
 		/* Always report DSR as active */
 		data->msr_mask_on |= UART_MSR_DSR;
 		data->msr_mask_off |= UART_MSR_DDSR;
 	}
 
-	if (of_property_read_bool(np, "cts-override")) {
+	if (device_property_read_bool(p->dev, "cts-override")) {
 		/* Always report CTS as active */
 		data->msr_mask_on |= UART_MSR_CTS;
 		data->msr_mask_off |= UART_MSR_DCTS;
 	}
 
-	if (of_property_read_bool(np, "ri-override")) {
+	if (device_property_read_bool(p->dev, "ri-override")) {
 		/* Always report Ring indicator as inactive */
 		data->msr_mask_off |= UART_MSR_RI;
 		data->msr_mask_off |= UART_MSR_TERI;
 	}
 
-	return 0;
-}
-
-static int dw8250_probe_acpi(struct uart_8250_port *up,
-			     struct dw8250_data *data)
-{
-	struct uart_port *p = &up->port;
-
-	dw8250_setup_port(up);
-
-	p->iotype = UPIO_MEM32;
-	p->serial_in = dw8250_serial_in32;
-	p->serial_out = dw8250_serial_out32;
-	p->regshift = 2;
-
-	up->dma = &data->dma;
-
-	up->dma->rxconf.src_maxburst = p->fifosize / 4;
-	up->dma->txconf.dst_maxburst = p->fifosize / 4;
-
-	up->port.set_termios = dw8250_set_termios;
-
-	return 0;
-}
-
-static int dw8250_probe(struct platform_device *pdev)
-{
-	struct uart_8250_port uart = {};
-	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	int irq = platform_get_irq(pdev, 0);
-	struct dw8250_data *data;
-	int err;
-
-	if (!regs) {
-		dev_err(&pdev->dev, "no registers defined\n");
-		return -EINVAL;
-	}
-
-	if (irq < 0) {
-		if (irq != -EPROBE_DEFER)
-			dev_err(&pdev->dev, "cannot get irq\n");
-		return irq;
-	}
-
-	spin_lock_init(&uart.port.lock);
-	uart.port.mapbase = regs->start;
-	uart.port.irq = irq;
-	uart.port.handle_irq = dw8250_handle_irq;
-	uart.port.pm = dw8250_do_pm;
-	uart.port.type = PORT_8250;
-	uart.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
-	uart.port.dev = &pdev->dev;
-
-	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
-					 resource_size(regs));
-	if (!uart.port.membase)
-		return -ENOMEM;
-
-	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
-
-	data->usr_reg = DW_UART_USR;
-
 	/* Always ask for fixed clock rate from a property. */
-	device_property_read_u32(&pdev->dev, "clock-frequency",
-				 &uart.port.uartclk);
+	device_property_read_u32(p->dev, "clock-frequency", &p->uartclk);
 
 	/* If there is separate baudclk, get the rate from it. */
 	data->clk = devm_clk_get(&pdev->dev, "baudclk");
@@ -454,11 +430,11 @@ static int dw8250_probe(struct platform_device *pdev)
 			dev_warn(&pdev->dev, "could not enable optional baudclk: %d\n",
 				 err);
 		else
-			uart.port.uartclk = clk_get_rate(data->clk);
+			p->uartclk = clk_get_rate(data->clk);
 	}
 
 	/* If no clock rate is defined, fail. */
-	if (!uart.port.uartclk) {
+	if (!p->uartclk) {
 		dev_err(&pdev->dev, "clock rate not defined\n");
 		return -EINVAL;
 	}
@@ -484,26 +460,22 @@ static int dw8250_probe(struct platform_device *pdev)
 	if (!IS_ERR(data->rst))
 		reset_control_deassert(data->rst);
 
-	data->dma.rx_param = data;
-	data->dma.tx_param = data;
-	data->dma.fn = dw8250_dma_filter;
+	dw8250_quirks(p, data);
 
-	uart.port.iotype = UPIO_MEM;
-	uart.port.serial_in = dw8250_serial_in;
-	uart.port.serial_out = dw8250_serial_out;
-	uart.port.private_data = data;
+	/* If the Busy Functionality is not implemented, don't handle it */
+	if (data->uart_16550_compatible) {
+		p->serial_out = NULL;
+		p->handle_irq = NULL;
+	}
 
-	if (pdev->dev.of_node) {
-		err = dw8250_probe_of(&uart.port, data);
-		if (err)
-			goto err_reset;
-	} else if (ACPI_HANDLE(&pdev->dev)) {
-		err = dw8250_probe_acpi(&uart, data);
-		if (err)
-			goto err_reset;
-	} else {
-		err = -ENODEV;
-		goto err_reset;
+	if (!data->skip_autocfg)
+		dw8250_setup_port(p);
+
+	/* If we have a valid fifosize, try hooking up DMA */
+	if (p->fifosize) {
+		data->dma.rxconf.src_maxburst = p->fifosize / 4;
+		data->dma.txconf.dst_maxburst = p->fifosize / 4;
+		uart.dma = &data->dma;
 	}
 
 	data->line = serial8250_register_8250_port(&uart);
diff --git a/kernel/drivers/tty/serial/8250/8250_early.c b/kernel/drivers/tty/serial/8250/8250_early.c
index 6c0fd8b9d..ceb85792a 100644
--- a/kernel/drivers/tty/serial/8250/8250_early.c
+++ b/kernel/drivers/tty/serial/8250/8250_early.c
@@ -29,13 +29,15 @@
 #include <linux/tty.h>
 #include <linux/init.h>
 #include <linux/console.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/serial_reg.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
 #include <asm/io.h>
 #include <asm/serial.h>
 
-unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offset)
+static unsigned int __init serial8250_early_in(struct uart_port *port, int offset)
 {
 	switch (port->iotype) {
 	case UPIO_MEM:
@@ -51,7 +53,7 @@ unsigned int __weak __init serial8250_early_in(struct uart_port *port, int offse
 	}
 }
 
-void __weak __init serial8250_early_out(struct uart_port *port, int offset, int value)
+static void __init serial8250_early_out(struct uart_port *port, int offset, int value)
 {
 	switch (port->iotype) {
 	case UPIO_MEM:
@@ -131,7 +133,7 @@ static void __init init_port(struct earlycon_device *device)
 	serial8250_early_out(port, UART_LCR, c & ~UART_LCR_DLAB);
 }
 
-static int __init early_serial8250_setup(struct earlycon_device *device,
+int __init early_serial8250_setup(struct earlycon_device *device,
 					 const char *options)
 {
 	if (!(device->port.membase || device->port.iobase))
@@ -152,3 +154,5 @@ static int __init early_serial8250_setup(struct earlycon_device *device,
 }
 EARLYCON_DECLARE(uart8250, early_serial8250_setup);
 EARLYCON_DECLARE(uart, early_serial8250_setup);
+OF_EARLYCON_DECLARE(ns16550, "ns16550", early_serial8250_setup);
+OF_EARLYCON_DECLARE(ns16550a, "ns16550a", early_serial8250_setup);
diff --git a/kernel/drivers/tty/serial/8250/8250_fintek.c b/kernel/drivers/tty/serial/8250/8250_fintek.c
index 5815e81b5..89474399a 100644
--- a/kernel/drivers/tty/serial/8250/8250_fintek.c
+++ b/kernel/drivers/tty/serial/8250/8250_fintek.c
@@ -17,18 +17,19 @@
 #include <linux/serial_core.h>
 #include  "8250.h"
 
-#define ADDR_PORT 0x4E
-#define DATA_PORT 0x4F
-#define ENTRY_KEY 0x77
+#define ADDR_PORT 0
+#define DATA_PORT 1
 #define EXIT_KEY 0xAA
 #define CHIP_ID1  0x20
-#define CHIP_ID1_VAL 0x02
 #define CHIP_ID2  0x21
-#define CHIP_ID2_VAL 0x16
+#define CHIP_ID_0 0x1602
+#define CHIP_ID_1 0x0501
 #define VENDOR_ID1 0x23
 #define VENDOR_ID1_VAL 0x19
 #define VENDOR_ID2 0x24
 #define VENDOR_ID2_VAL 0x34
+#define IO_ADDR1 0x61
+#define IO_ADDR2 0x60
 #define LDN 0x7
 
 #define RS485  0xF0
@@ -39,51 +40,49 @@
 
 #define DRIVER_NAME "8250_fintek"
 
-static int fintek_8250_enter_key(void){
+struct fintek_8250 {
+	u16 base_port;
+	u8 index;
+	u8 key;
+	long line;
+};
+
+static int fintek_8250_enter_key(u16 base_port, u8 key)
+{
 
-	if (!request_muxed_region(ADDR_PORT, 2, DRIVER_NAME))
+	if (!request_muxed_region(base_port, 2, DRIVER_NAME))
 		return -EBUSY;
 
-	outb(ENTRY_KEY, ADDR_PORT);
-	outb(ENTRY_KEY, ADDR_PORT);
+	outb(key, base_port + ADDR_PORT);
+	outb(key, base_port + ADDR_PORT);
 	return 0;
 }
 
-static void fintek_8250_exit_key(void){
-
-	outb(EXIT_KEY, ADDR_PORT);
-	release_region(ADDR_PORT, 2);
-}
-
-static int fintek_8250_get_index(resource_size_t base_addr)
+static void fintek_8250_exit_key(u16 base_port)
 {
-	resource_size_t base[] = {0x3f8, 0x2f8, 0x3e8, 0x2e8};
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(base); i++)
-		if (base_addr == base[i])
-			return i;
 
-	return -ENODEV;
+	outb(EXIT_KEY, base_port + ADDR_PORT);
+	release_region(base_port + ADDR_PORT, 2);
 }
 
-static int fintek_8250_check_id(void)
+static int fintek_8250_check_id(u16 base_port)
 {
+	u16 chip;
 
-	outb(CHIP_ID1, ADDR_PORT);
-	if (inb(DATA_PORT) != CHIP_ID1_VAL)
+	outb(VENDOR_ID1, base_port + ADDR_PORT);
+	if (inb(base_port + DATA_PORT) != VENDOR_ID1_VAL)
 		return -ENODEV;
 
-	outb(CHIP_ID2, ADDR_PORT);
-	if (inb(DATA_PORT) != CHIP_ID2_VAL)
+	outb(VENDOR_ID2, base_port + ADDR_PORT);
+	if (inb(base_port + DATA_PORT) != VENDOR_ID2_VAL)
 		return -ENODEV;
 
-	outb(VENDOR_ID1, ADDR_PORT);
-	if (inb(DATA_PORT) != VENDOR_ID1_VAL)
-		return -ENODEV;
+	outb(CHIP_ID1, base_port + ADDR_PORT);
+	chip = inb(base_port + DATA_PORT);
+	outb(CHIP_ID2, base_port + ADDR_PORT);
+	chip |= inb(base_port + DATA_PORT) << 8;
 
-	outb(VENDOR_ID2, ADDR_PORT);
-	if (inb(DATA_PORT) != VENDOR_ID2_VAL)
+	if (chip != CHIP_ID_0 && chip != CHIP_ID_1)
 		return -ENODEV;
 
 	return 0;
@@ -93,9 +92,9 @@ static int fintek_8250_rs485_config(struct uart_port *port,
 			      struct serial_rs485 *rs485)
 {
 	uint8_t config = 0;
-	int index = fintek_8250_get_index(port->iobase);
+	struct fintek_8250 *pdata = port->private_data;
 
-	if (index < 0)
+	if (!pdata)
 		return -EINVAL;
 
 	if (rs485->flags & SER_RS485_ENABLED)
@@ -125,44 +124,84 @@ static int fintek_8250_rs485_config(struct uart_port *port,
 	if (rs485->flags & SER_RS485_RTS_ON_SEND)
 		config |= RTS_INVERT;
 
-	if (fintek_8250_enter_key())
+	if (fintek_8250_enter_key(pdata->base_port, pdata->key))
 		return -EBUSY;
 
-	outb(LDN, ADDR_PORT);
-	outb(index, DATA_PORT);
-	outb(RS485, ADDR_PORT);
-	outb(config, DATA_PORT);
-	fintek_8250_exit_key();
+	outb(LDN, pdata->base_port + ADDR_PORT);
+	outb(pdata->index, pdata->base_port + DATA_PORT);
+	outb(RS485, pdata->base_port + ADDR_PORT);
+	outb(config, pdata->base_port + DATA_PORT);
+	fintek_8250_exit_key(pdata->base_port);
 
 	port->rs485 = *rs485;
 
 	return 0;
 }
 
+static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index)
+{
+	static const u16 addr[] = {0x4e, 0x2e};
+	static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67};
+	int i, j, k;
+
+	for (i = 0; i < ARRAY_SIZE(addr); i++) {
+		for (j = 0; j < ARRAY_SIZE(keys); j++) {
+
+			if (fintek_8250_enter_key(addr[i], keys[j]))
+				continue;
+			if (fintek_8250_check_id(addr[i])) {
+				fintek_8250_exit_key(addr[i]);
+				continue;
+			}
+
+			for (k = 0; k < 4; k++) {
+				u16 aux;
+
+				outb(LDN, addr[i] + ADDR_PORT);
+				outb(k, addr[i] + DATA_PORT);
+
+				outb(IO_ADDR1, addr[i] + ADDR_PORT);
+				aux = inb(addr[i] + DATA_PORT);
+				outb(IO_ADDR2, addr[i] + ADDR_PORT);
+				aux |= inb(addr[i] + DATA_PORT) << 8;
+				if (aux != io_address)
+					continue;
+
+				fintek_8250_exit_key(addr[i]);
+				*key = keys[j];
+				*index = k;
+				return addr[i];
+			}
+			fintek_8250_exit_key(addr[i]);
+		}
+	}
+
+	return -ENODEV;
+}
+
 static int
 fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 {
-	int line;
 	struct uart_8250_port uart;
-	int ret;
+	struct fintek_8250 *pdata;
+	int base_port;
+	u8 key;
+	u8 index;
 
 	if (!pnp_port_valid(dev, 0))
 		return -ENODEV;
 
-	if (fintek_8250_get_index(pnp_port_start(dev, 0)) < 0)
+	base_port = fintek_8250_base_port(pnp_port_start(dev, 0), &key, &index);
+	if (base_port < 0)
 		return -ENODEV;
 
-	/* Enable configuration registers*/
-	if (fintek_8250_enter_key())
-		return -EBUSY;
+	memset(&uart, 0, sizeof(uart));
 
-	/*Check ID*/
-	ret = fintek_8250_check_id();
-	fintek_8250_exit_key();
-	if (ret)
-		return ret;
+	pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+	uart.port.private_data = pdata;
 
-	memset(&uart, 0, sizeof(uart));
 	if (!pnp_irq_valid(dev, 0))
 		return -ENODEV;
 	uart.port.irq = pnp_irq(dev, 0);
@@ -176,40 +215,43 @@ fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 	uart.port.uartclk = 1843200;
 	uart.port.dev = &dev->dev;
 
-	line = serial8250_register_8250_port(&uart);
-	if (line < 0)
+	pdata->key = key;
+	pdata->base_port = base_port;
+	pdata->index = index;
+	pdata->line = serial8250_register_8250_port(&uart);
+	if (pdata->line < 0)
 		return -ENODEV;
 
-	pnp_set_drvdata(dev, (void *)((long)line + 1));
+	pnp_set_drvdata(dev, pdata);
 	return 0;
 }
 
 static void fintek_8250_remove(struct pnp_dev *dev)
 {
-	long line = (long)pnp_get_drvdata(dev);
+	struct fintek_8250 *pdata = pnp_get_drvdata(dev);
 
-	if (line)
-		serial8250_unregister_port(line - 1);
+	if (pdata)
+		serial8250_unregister_port(pdata->line);
 }
 
 #ifdef CONFIG_PM
 static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state)
 {
-	long line = (long)pnp_get_drvdata(dev);
+	struct fintek_8250 *pdata = pnp_get_drvdata(dev);
 
-	if (!line)
+	if (!pdata)
 		return -ENODEV;
-	serial8250_suspend_port(line - 1);
+	serial8250_suspend_port(pdata->line);
 	return 0;
 }
 
 static int fintek_8250_resume(struct pnp_dev *dev)
 {
-	long line = (long)pnp_get_drvdata(dev);
+	struct fintek_8250 *pdata = pnp_get_drvdata(dev);
 
-	if (!line)
+	if (!pdata)
 		return -ENODEV;
-	serial8250_resume_port(line - 1);
+	serial8250_resume_port(pdata->line);
 	return 0;
 }
 #else
diff --git a/kernel/drivers/tty/serial/8250/8250_fsl.c b/kernel/drivers/tty/serial/8250/8250_fsl.c
index c0533a57e..910bfee5a 100644
--- a/kernel/drivers/tty/serial/8250/8250_fsl.c
+++ b/kernel/drivers/tty/serial/8250/8250_fsl.c
@@ -60,3 +60,4 @@ int fsl8250_handle_irq(struct uart_port *port)
 	spin_unlock_irqrestore(&up->port.lock, flags);
 	return 1;
 }
+EXPORT_SYMBOL_GPL(fsl8250_handle_irq);
diff --git a/kernel/drivers/tty/serial/8250/8250_ingenic.c b/kernel/drivers/tty/serial/8250/8250_ingenic.c
new file mode 100644
index 000000000..49394b4c5
--- /dev/null
+++ b/kernel/drivers/tty/serial/8250/8250_ingenic.c
@@ -0,0 +1,345 @@
+/*
+ * Copyright (C) 2010 Lars-Peter Clausen <lars@metafoo.de>
+ * Copyright (C) 2015 Imagination Technologies
+ *
+ * Ingenic SoC UART support
+ *
+ * This program is free software; you can redistribute	 it and/or modify it
+ * under  the terms of	 the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the	License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the  GNU General Public License along
+ * with this program; if not, write  to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/libfdt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_fdt.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+
+#include "8250.h"
+
+/** ingenic_uart_config: SOC specific config data. */
+struct ingenic_uart_config {
+	int tx_loadsz;
+	int fifosize;
+};
+
+struct ingenic_uart_data {
+	struct clk	*clk_module;
+	struct clk	*clk_baud;
+	int		line;
+};
+
+static const struct of_device_id of_match[];
+
+#define UART_FCR_UME	BIT(4)
+
+#define UART_MCR_MDCE	BIT(7)
+#define UART_MCR_FCM	BIT(6)
+
+static struct earlycon_device *early_device;
+
+static uint8_t __init early_in(struct uart_port *port, int offset)
+{
+	return readl(port->membase + (offset << 2));
+}
+
+static void __init early_out(struct uart_port *port, int offset, uint8_t value)
+{
+	writel(value, port->membase + (offset << 2));
+}
+
+static void __init ingenic_early_console_putc(struct uart_port *port, int c)
+{
+	uint8_t lsr;
+
+	do {
+		lsr = early_in(port, UART_LSR);
+	} while ((lsr & UART_LSR_TEMT) == 0);
+
+	early_out(port, UART_TX, c);
+}
+
+static void __init ingenic_early_console_write(struct console *console,
+					      const char *s, unsigned int count)
+{
+	uart_console_write(&early_device->port, s, count,
+			   ingenic_early_console_putc);
+}
+
+static void __init ingenic_early_console_setup_clock(struct earlycon_device *dev)
+{
+	void *fdt = initial_boot_params;
+	const __be32 *prop;
+	int offset;
+
+	offset = fdt_path_offset(fdt, "/ext");
+	if (offset < 0)
+		return;
+
+	prop = fdt_getprop(fdt, offset, "clock-frequency", NULL);
+	if (!prop)
+		return;
+
+	dev->port.uartclk = be32_to_cpup(prop);
+}
+
+static int __init ingenic_early_console_setup(struct earlycon_device *dev,
+					      const char *opt)
+{
+	struct uart_port *port = &dev->port;
+	unsigned int baud, divisor;
+
+	if (!dev->port.membase)
+		return -ENODEV;
+
+	ingenic_early_console_setup_clock(dev);
+
+	baud = dev->baud ?: 115200;
+	divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud);
+
+	early_out(port, UART_IER, 0);
+	early_out(port, UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8);
+	early_out(port, UART_DLL, 0);
+	early_out(port, UART_DLM, 0);
+	early_out(port, UART_LCR, UART_LCR_WLEN8);
+	early_out(port, UART_FCR, UART_FCR_UME | UART_FCR_CLEAR_XMIT |
+			UART_FCR_CLEAR_RCVR | UART_FCR_ENABLE_FIFO);
+	early_out(port, UART_MCR, UART_MCR_RTS | UART_MCR_DTR);
+
+	early_out(port, UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8);
+	early_out(port, UART_DLL, divisor & 0xff);
+	early_out(port, UART_DLM, (divisor >> 8) & 0xff);
+	early_out(port, UART_LCR, UART_LCR_WLEN8);
+
+	early_device = dev;
+	dev->con->write = ingenic_early_console_write;
+
+	return 0;
+}
+
+EARLYCON_DECLARE(jz4740_uart, ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart",
+		    ingenic_early_console_setup);
+
+EARLYCON_DECLARE(jz4775_uart, ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4775_uart, "ingenic,jz4775-uart",
+		    ingenic_early_console_setup);
+
+EARLYCON_DECLARE(jz4780_uart, ingenic_early_console_setup);
+OF_EARLYCON_DECLARE(jz4780_uart, "ingenic,jz4780-uart",
+		    ingenic_early_console_setup);
+
+static void ingenic_uart_serial_out(struct uart_port *p, int offset, int value)
+{
+	int ier;
+
+	switch (offset) {
+	case UART_FCR:
+		/* UART module enable */
+		value |= UART_FCR_UME;
+		break;
+
+	case UART_IER:
+		/* Enable receive timeout interrupt with the
+		 * receive line status interrupt */
+		value |= (value & 0x4) << 2;
+		break;
+
+	case UART_MCR:
+		/* If we have enabled modem status IRQs we should enable modem
+		 * mode. */
+		ier = p->serial_in(p, UART_IER);
+
+		if (ier & UART_IER_MSI)
+			value |= UART_MCR_MDCE | UART_MCR_FCM;
+		else
+			value &= ~(UART_MCR_MDCE | UART_MCR_FCM);
+		break;
+
+	default:
+		break;
+	}
+
+	writeb(value, p->membase + (offset << p->regshift));
+}
+
+static unsigned int ingenic_uart_serial_in(struct uart_port *p, int offset)
+{
+	unsigned int value;
+
+	value = readb(p->membase + (offset << p->regshift));
+
+	/* Hide non-16550 compliant bits from higher levels */
+	switch (offset) {
+	case UART_FCR:
+		value &= ~UART_FCR_UME;
+		break;
+
+	case UART_MCR:
+		value &= ~(UART_MCR_MDCE | UART_MCR_FCM);
+		break;
+
+	default:
+		break;
+	}
+	return value;
+}
+
+static int ingenic_uart_probe(struct platform_device *pdev)
+{
+	struct uart_8250_port uart = {};
+	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	struct ingenic_uart_data *data;
+	const struct ingenic_uart_config *cdata;
+	const struct of_device_id *match;
+	int err, line;
+
+	match = of_match_device(of_match, &pdev->dev);
+	if (!match) {
+		dev_err(&pdev->dev, "Error: No device match found\n");
+		return -ENODEV;
+	}
+	cdata = match->data;
+
+	if (!regs || !irq) {
+		dev_err(&pdev->dev, "no registers/irq defined\n");
+		return -EINVAL;
+	}
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	spin_lock_init(&uart.port.lock);
+	uart.port.type = PORT_16550A;
+	uart.port.flags = UPF_SKIP_TEST | UPF_IOREMAP | UPF_FIXED_TYPE;
+	uart.port.iotype = UPIO_MEM;
+	uart.port.mapbase = regs->start;
+	uart.port.regshift = 2;
+	uart.port.serial_out = ingenic_uart_serial_out;
+	uart.port.serial_in = ingenic_uart_serial_in;
+	uart.port.irq = irq->start;
+	uart.port.dev = &pdev->dev;
+	uart.port.fifosize = cdata->fifosize;
+	uart.tx_loadsz = cdata->tx_loadsz;
+	uart.capabilities = UART_CAP_FIFO | UART_CAP_RTOIE;
+
+	/* Check for a fixed line number */
+	line = of_alias_get_id(pdev->dev.of_node, "serial");
+	if (line >= 0)
+		uart.port.line = line;
+
+	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+					 resource_size(regs));
+	if (!uart.port.membase)
+		return -ENOMEM;
+
+	data->clk_module = devm_clk_get(&pdev->dev, "module");
+	if (IS_ERR(data->clk_module)) {
+		err = PTR_ERR(data->clk_module);
+		if (err != -EPROBE_DEFER)
+			dev_err(&pdev->dev,
+				"unable to get module clock: %d\n", err);
+		return err;
+	}
+
+	data->clk_baud = devm_clk_get(&pdev->dev, "baud");
+	if (IS_ERR(data->clk_baud)) {
+		err = PTR_ERR(data->clk_baud);
+		if (err != -EPROBE_DEFER)
+			dev_err(&pdev->dev,
+				"unable to get baud clock: %d\n", err);
+		return err;
+	}
+
+	err = clk_prepare_enable(data->clk_module);
+	if (err) {
+		dev_err(&pdev->dev, "could not enable module clock: %d\n", err);
+		goto out;
+	}
+
+	err = clk_prepare_enable(data->clk_baud);
+	if (err) {
+		dev_err(&pdev->dev, "could not enable baud clock: %d\n", err);
+		goto out_disable_moduleclk;
+	}
+	uart.port.uartclk = clk_get_rate(data->clk_baud);
+
+	data->line = serial8250_register_8250_port(&uart);
+	if (data->line < 0) {
+		err = data->line;
+		goto out_disable_baudclk;
+	}
+
+	platform_set_drvdata(pdev, data);
+	return 0;
+
+out_disable_baudclk:
+	clk_disable_unprepare(data->clk_baud);
+out_disable_moduleclk:
+	clk_disable_unprepare(data->clk_module);
+out:
+	return err;
+}
+
+static int ingenic_uart_remove(struct platform_device *pdev)
+{
+	struct ingenic_uart_data *data = platform_get_drvdata(pdev);
+
+	serial8250_unregister_port(data->line);
+	clk_disable_unprepare(data->clk_module);
+	clk_disable_unprepare(data->clk_baud);
+	return 0;
+}
+
+static const struct ingenic_uart_config jz4740_uart_config = {
+	.tx_loadsz = 8,
+	.fifosize = 16,
+};
+
+static const struct ingenic_uart_config jz4760_uart_config = {
+	.tx_loadsz = 16,
+	.fifosize = 32,
+};
+
+static const struct ingenic_uart_config jz4780_uart_config = {
+	.tx_loadsz = 32,
+	.fifosize = 64,
+};
+
+static const struct of_device_id of_match[] = {
+	{ .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config },
+	{ .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config },
+	{ .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config },
+	{ .compatible = "ingenic,jz4780-uart", .data = &jz4780_uart_config },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, of_match);
+
+static struct platform_driver ingenic_uart_platform_driver = {
+	.driver = {
+		.name		= "ingenic-uart",
+		.of_match_table	= of_match,
+	},
+	.probe			= ingenic_uart_probe,
+	.remove			= ingenic_uart_remove,
+};
+
+module_platform_driver(ingenic_uart_platform_driver);
+
+MODULE_AUTHOR("Paul Burton");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Ingenic SoC UART driver");
diff --git a/kernel/drivers/tty/serial/8250/8250_lpc18xx.c b/kernel/drivers/tty/serial/8250/8250_lpc18xx.c
new file mode 100644
index 000000000..99cd47885
--- /dev/null
+++ b/kernel/drivers/tty/serial/8250/8250_lpc18xx.c
@@ -0,0 +1,230 @@
+/*
+ * Serial port driver for NXP LPC18xx/43xx UART
+ *
+ * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * Based on 8250_mtk.c:
+ * Copyright (c) 2014 MundoReader S.L.
+ * Matthias Brugger <matthias.bgg@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "8250.h"
+
+/* Additional LPC18xx/43xx 8250 registers and bits */
+#define LPC18XX_UART_RS485CTRL		(0x04c / sizeof(u32))
+#define  LPC18XX_UART_RS485CTRL_NMMEN	BIT(0)
+#define  LPC18XX_UART_RS485CTRL_DCTRL	BIT(4)
+#define  LPC18XX_UART_RS485CTRL_OINV	BIT(5)
+#define LPC18XX_UART_RS485DLY		(0x054 / sizeof(u32))
+#define LPC18XX_UART_RS485DLY_MAX	255
+
+struct lpc18xx_uart_data {
+	struct uart_8250_dma dma;
+	struct clk *clk_uart;
+	struct clk *clk_reg;
+	int line;
+};
+
+static int lpc18xx_rs485_config(struct uart_port *port,
+				struct serial_rs485 *rs485)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	u32 rs485_ctrl_reg = 0;
+	u32 rs485_dly_reg = 0;
+	unsigned baud_clk;
+
+	if (rs485->flags & SER_RS485_ENABLED)
+		memset(rs485->padding, 0, sizeof(rs485->padding));
+	else
+		memset(rs485, 0, sizeof(*rs485));
+
+	rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+			SER_RS485_RTS_AFTER_SEND;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN |
+				  LPC18XX_UART_RS485CTRL_DCTRL;
+
+		if (rs485->flags & SER_RS485_RTS_ON_SEND) {
+			rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV;
+			rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
+		} else {
+			rs485->flags |= SER_RS485_RTS_AFTER_SEND;
+		}
+	}
+
+	if (rs485->delay_rts_after_send) {
+		baud_clk = port->uartclk / up->dl_read(up);
+		rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send
+						* baud_clk, MSEC_PER_SEC);
+
+		if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX)
+			rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX;
+
+		/* Calculate the resulting delay in ms */
+		rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC)
+						/ baud_clk;
+	}
+
+	/* Delay RTS before send not supported */
+	rs485->delay_rts_before_send = 0;
+
+	serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg);
+	serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg);
+
+	port->rs485 = *rs485;
+
+	return 0;
+}
+
+static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value)
+{
+	/*
+	 * For DMA mode one must ensure that the UART_FCR_DMA_SELECT
+	 * bit is set when FIFO is enabled. Even if DMA is not used
+	 * setting this bit doesn't seem to affect anything.
+	 */
+	if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO))
+		value |= UART_FCR_DMA_SELECT;
+
+	offset = offset << p->regshift;
+	writel(value, p->membase + offset);
+}
+
+static int lpc18xx_serial_probe(struct platform_device *pdev)
+{
+	struct lpc18xx_uart_data *data;
+	struct uart_8250_port uart;
+	struct resource *res;
+	int irq, ret;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "irq not found");
+		return irq;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "memory resource not found");
+		return -EINVAL;
+	}
+
+	memset(&uart, 0, sizeof(uart));
+
+	uart.port.membase = devm_ioremap(&pdev->dev, res->start,
+					 resource_size(res));
+	if (!uart.port.membase)
+		return -ENOMEM;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->clk_uart = devm_clk_get(&pdev->dev, "uartclk");
+	if (IS_ERR(data->clk_uart)) {
+		dev_err(&pdev->dev, "uart clock not found\n");
+		return PTR_ERR(data->clk_uart);
+	}
+
+	data->clk_reg = devm_clk_get(&pdev->dev, "reg");
+	if (IS_ERR(data->clk_reg)) {
+		dev_err(&pdev->dev, "reg clock not found\n");
+		return PTR_ERR(data->clk_reg);
+	}
+
+	ret = clk_prepare_enable(data->clk_reg);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to enable reg clock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(data->clk_uart);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to enable uart clock\n");
+		goto dis_clk_reg;
+	}
+
+	ret = of_alias_get_id(pdev->dev.of_node, "serial");
+	if (ret >= 0)
+		uart.port.line = ret;
+
+	data->dma.rx_param = data;
+	data->dma.tx_param = data;
+
+	spin_lock_init(&uart.port.lock);
+	uart.port.dev = &pdev->dev;
+	uart.port.irq = irq;
+	uart.port.iotype = UPIO_MEM32;
+	uart.port.mapbase = res->start;
+	uart.port.regshift = 2;
+	uart.port.type = PORT_16550A;
+	uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST;
+	uart.port.uartclk = clk_get_rate(data->clk_uart);
+	uart.port.private_data = data;
+	uart.port.rs485_config = lpc18xx_rs485_config;
+	uart.port.serial_out = lpc18xx_uart_serial_out;
+
+	uart.dma = &data->dma;
+	uart.dma->rxconf.src_maxburst = 1;
+	uart.dma->txconf.dst_maxburst = 1;
+
+	ret = serial8250_register_8250_port(&uart);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "unable to register 8250 port\n");
+		goto dis_uart_clk;
+	}
+
+	data->line = ret;
+	platform_set_drvdata(pdev, data);
+
+	return 0;
+
+dis_uart_clk:
+	clk_disable_unprepare(data->clk_uart);
+dis_clk_reg:
+	clk_disable_unprepare(data->clk_reg);
+	return ret;
+}
+
+static int lpc18xx_serial_remove(struct platform_device *pdev)
+{
+	struct lpc18xx_uart_data *data = platform_get_drvdata(pdev);
+
+	serial8250_unregister_port(data->line);
+	clk_disable_unprepare(data->clk_uart);
+	clk_disable_unprepare(data->clk_reg);
+
+	return 0;
+}
+
+static const struct of_device_id lpc18xx_serial_match[] = {
+	{ .compatible = "nxp,lpc1850-uart" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, lpc18xx_serial_match);
+
+static struct platform_driver lpc18xx_serial_driver = {
+	.probe  = lpc18xx_serial_probe,
+	.remove = lpc18xx_serial_remove,
+	.driver = {
+		.name = "lpc18xx-uart",
+		.of_match_table = lpc18xx_serial_match,
+	},
+};
+module_platform_driver(lpc18xx_serial_driver);
+
+MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>");
+MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices");
+MODULE_LICENSE("GPL v2");
diff --git a/kernel/drivers/tty/serial/8250/8250_mid.c b/kernel/drivers/tty/serial/8250/8250_mid.c
new file mode 100644
index 000000000..88531a36b
--- /dev/null
+++ b/kernel/drivers/tty/serial/8250/8250_mid.c
@@ -0,0 +1,326 @@
+/*
+ * 8250_mid.c - Driver for UART on Intel Penwell and various other Intel SOCs
+ *
+ * Copyright (C) 2015 Intel Corporation
+ * Author: Heikki Krogerus <heikki.krogerus@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/rational.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+
+#include <linux/dma/hsu.h>
+
+#include "8250.h"
+
+#define PCI_DEVICE_ID_INTEL_PNW_UART1	0x081b
+#define PCI_DEVICE_ID_INTEL_PNW_UART2	0x081c
+#define PCI_DEVICE_ID_INTEL_PNW_UART3	0x081d
+#define PCI_DEVICE_ID_INTEL_TNG_UART	0x1191
+#define PCI_DEVICE_ID_INTEL_DNV_UART	0x19d8
+
+/* Intel MID Specific registers */
+#define INTEL_MID_UART_PS		0x30
+#define INTEL_MID_UART_MUL		0x34
+#define INTEL_MID_UART_DIV		0x38
+
+struct mid8250;
+
+struct mid8250_board {
+	unsigned long freq;
+	unsigned int base_baud;
+	int (*setup)(struct mid8250 *, struct uart_port *p);
+	void (*exit)(struct mid8250 *);
+};
+
+struct mid8250 {
+	int line;
+	int dma_index;
+	struct pci_dev *dma_dev;
+	struct uart_8250_dma dma;
+	struct mid8250_board *board;
+	struct hsu_dma_chip dma_chip;
+};
+
+/*****************************************************************************/
+
+static int pnw_setup(struct mid8250 *mid, struct uart_port *p)
+{
+	struct pci_dev *pdev = to_pci_dev(p->dev);
+
+	switch (pdev->device) {
+	case PCI_DEVICE_ID_INTEL_PNW_UART1:
+		mid->dma_index = 0;
+		break;
+	case PCI_DEVICE_ID_INTEL_PNW_UART2:
+		mid->dma_index = 1;
+		break;
+	case PCI_DEVICE_ID_INTEL_PNW_UART3:
+		mid->dma_index = 2;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	mid->dma_dev = pci_get_slot(pdev->bus,
+				    PCI_DEVFN(PCI_SLOT(pdev->devfn), 3));
+	return 0;
+}
+
+static int tng_setup(struct mid8250 *mid, struct uart_port *p)
+{
+	struct pci_dev *pdev = to_pci_dev(p->dev);
+	int index = PCI_FUNC(pdev->devfn);
+
+	/* Currently no support for HSU port0 */
+	if (index-- == 0)
+		return -ENODEV;
+
+	mid->dma_index = index;
+	mid->dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(5, 0));
+	return 0;
+}
+
+static int dnv_handle_irq(struct uart_port *p)
+{
+	struct mid8250 *mid = p->private_data;
+	int ret;
+
+	ret = hsu_dma_irq(&mid->dma_chip, 0);
+	ret |= hsu_dma_irq(&mid->dma_chip, 1);
+
+	/* For now, letting the HW generate separate interrupt for the UART */
+	if (ret)
+		return ret;
+
+	return serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+}
+
+#define DNV_DMA_CHAN_OFFSET 0x80
+
+static int dnv_setup(struct mid8250 *mid, struct uart_port *p)
+{
+	struct hsu_dma_chip *chip = &mid->dma_chip;
+	struct pci_dev *pdev = to_pci_dev(p->dev);
+	int ret;
+
+	chip->dev = &pdev->dev;
+	chip->irq = pdev->irq;
+	chip->regs = p->membase;
+	chip->length = pci_resource_len(pdev, 0);
+	chip->offset = DNV_DMA_CHAN_OFFSET;
+
+	/* Falling back to PIO mode if DMA probing fails */
+	ret = hsu_dma_probe(chip);
+	if (ret)
+		return 0;
+
+	mid->dma_dev = pdev;
+
+	p->handle_irq = dnv_handle_irq;
+	return 0;
+}
+
+static void dnv_exit(struct mid8250 *mid)
+{
+	if (!mid->dma_dev)
+		return;
+	hsu_dma_remove(&mid->dma_chip);
+}
+
+/*****************************************************************************/
+
+static void mid8250_set_termios(struct uart_port *p,
+				struct ktermios *termios,
+				struct ktermios *old)
+{
+	unsigned int baud = tty_termios_baud_rate(termios);
+	struct mid8250 *mid = p->private_data;
+	unsigned short ps = 16;
+	unsigned long fuart = baud * ps;
+	unsigned long w = BIT(24) - 1;
+	unsigned long mul, div;
+
+	if (mid->board->freq < fuart) {
+		/* Find prescaler value that satisfies Fuart < Fref */
+		if (mid->board->freq > baud)
+			ps = mid->board->freq / baud;	/* baud rate too high */
+		else
+			ps = 1;				/* PLL case */
+		fuart = baud * ps;
+	} else {
+		/* Get Fuart closer to Fref */
+		fuart *= rounddown_pow_of_two(mid->board->freq / fuart);
+	}
+
+	rational_best_approximation(fuart, mid->board->freq, w, w, &mul, &div);
+	p->uartclk = fuart * 16 / ps;		/* core uses ps = 16 always */
+
+	writel(ps, p->membase + INTEL_MID_UART_PS);		/* set PS */
+	writel(mul, p->membase + INTEL_MID_UART_MUL);		/* set MUL */
+	writel(div, p->membase + INTEL_MID_UART_DIV);
+
+	serial8250_do_set_termios(p, termios, old);
+}
+
+static bool mid8250_dma_filter(struct dma_chan *chan, void *param)
+{
+	struct hsu_dma_slave *s = param;
+
+	if (s->dma_dev != chan->device->dev || s->chan_id != chan->chan_id)
+		return false;
+
+	chan->private = s;
+	return true;
+}
+
+static int mid8250_dma_setup(struct mid8250 *mid, struct uart_8250_port *port)
+{
+	struct uart_8250_dma *dma = &mid->dma;
+	struct device *dev = port->port.dev;
+	struct hsu_dma_slave *rx_param;
+	struct hsu_dma_slave *tx_param;
+
+	if (!mid->dma_dev)
+		return 0;
+
+	rx_param = devm_kzalloc(dev, sizeof(*rx_param), GFP_KERNEL);
+	if (!rx_param)
+		return -ENOMEM;
+
+	tx_param = devm_kzalloc(dev, sizeof(*tx_param), GFP_KERNEL);
+	if (!tx_param)
+		return -ENOMEM;
+
+	rx_param->chan_id = mid->dma_index * 2 + 1;
+	tx_param->chan_id = mid->dma_index * 2;
+
+	dma->rxconf.src_maxburst = 64;
+	dma->txconf.dst_maxburst = 64;
+
+	rx_param->dma_dev = &mid->dma_dev->dev;
+	tx_param->dma_dev = &mid->dma_dev->dev;
+
+	dma->fn = mid8250_dma_filter;
+	dma->rx_param = rx_param;
+	dma->tx_param = tx_param;
+
+	port->dma = dma;
+	return 0;
+}
+
+static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct uart_8250_port uart;
+	struct mid8250 *mid;
+	int ret;
+
+	ret = pcim_enable_device(pdev);
+	if (ret)
+		return ret;
+
+	pci_set_master(pdev);
+
+	mid = devm_kzalloc(&pdev->dev, sizeof(*mid), GFP_KERNEL);
+	if (!mid)
+		return -ENOMEM;
+
+	mid->board = (struct mid8250_board *)id->driver_data;
+
+	memset(&uart, 0, sizeof(struct uart_8250_port));
+
+	uart.port.dev = &pdev->dev;
+	uart.port.irq = pdev->irq;
+	uart.port.private_data = mid;
+	uart.port.type = PORT_16750;
+	uart.port.iotype = UPIO_MEM;
+	uart.port.uartclk = mid->board->base_baud * 16;
+	uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
+	uart.port.set_termios = mid8250_set_termios;
+
+	uart.port.mapbase = pci_resource_start(pdev, 0);
+	uart.port.membase = pcim_iomap(pdev, 0, 0);
+	if (!uart.port.membase)
+		return -ENOMEM;
+
+	if (mid->board->setup) {
+		ret = mid->board->setup(mid, &uart.port);
+		if (ret)
+			return ret;
+	}
+
+	ret = mid8250_dma_setup(mid, &uart);
+	if (ret)
+		goto err;
+
+	ret = serial8250_register_8250_port(&uart);
+	if (ret < 0)
+		goto err;
+
+	mid->line = ret;
+
+	pci_set_drvdata(pdev, mid);
+	return 0;
+err:
+	if (mid->board->exit)
+		mid->board->exit(mid);
+	return ret;
+}
+
+static void mid8250_remove(struct pci_dev *pdev)
+{
+	struct mid8250 *mid = pci_get_drvdata(pdev);
+
+	if (mid->board->exit)
+		mid->board->exit(mid);
+
+	serial8250_unregister_port(mid->line);
+}
+
+static const struct mid8250_board pnw_board = {
+	.freq = 50000000,
+	.base_baud = 115200,
+	.setup = pnw_setup,
+};
+
+static const struct mid8250_board tng_board = {
+	.freq = 38400000,
+	.base_baud = 1843200,
+	.setup = tng_setup,
+};
+
+static const struct mid8250_board dnv_board = {
+	.freq = 133333333,
+	.base_baud = 115200,
+	.setup = dnv_setup,
+	.exit = dnv_exit,
+};
+
+#define MID_DEVICE(id, board) { PCI_VDEVICE(INTEL, id), (kernel_ulong_t)&board }
+
+static const struct pci_device_id pci_ids[] = {
+	MID_DEVICE(PCI_DEVICE_ID_INTEL_PNW_UART1, pnw_board),
+	MID_DEVICE(PCI_DEVICE_ID_INTEL_PNW_UART2, pnw_board),
+	MID_DEVICE(PCI_DEVICE_ID_INTEL_PNW_UART3, pnw_board),
+	MID_DEVICE(PCI_DEVICE_ID_INTEL_TNG_UART, tng_board),
+	MID_DEVICE(PCI_DEVICE_ID_INTEL_DNV_UART, dnv_board),
+	{ },
+};
+MODULE_DEVICE_TABLE(pci, pci_ids);
+
+static struct pci_driver mid8250_pci_driver = {
+	.name           = "8250_mid",
+	.id_table       = pci_ids,
+	.probe          = mid8250_probe,
+	.remove         = mid8250_remove,
+};
+
+module_pci_driver(mid8250_pci_driver);
+
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Intel MID UART driver");
diff --git a/kernel/drivers/tty/serial/8250/8250_mtk.c b/kernel/drivers/tty/serial/8250/8250_mtk.c
index 7a11fac77..78883ca64 100644
--- a/kernel/drivers/tty/serial/8250/8250_mtk.c
+++ b/kernel/drivers/tty/serial/8250/8250_mtk.c
@@ -34,6 +34,7 @@
 struct mtk8250_data {
 	int			line;
 	struct clk		*uart_clk;
+	struct clk		*bus_clk;
 };
 
 static void
@@ -115,6 +116,36 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios,
 		tty_termios_encode_baud_rate(termios, baud, baud);
 }
 
+static int mtk8250_runtime_suspend(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(data->uart_clk);
+	clk_disable_unprepare(data->bus_clk);
+
+	return 0;
+}
+
+static int mtk8250_runtime_resume(struct device *dev)
+{
+	struct mtk8250_data *data = dev_get_drvdata(dev);
+	int err;
+
+	err = clk_prepare_enable(data->uart_clk);
+	if (err) {
+		dev_warn(dev, "Can't enable clock\n");
+		return err;
+	}
+
+	err = clk_prepare_enable(data->bus_clk);
+	if (err) {
+		dev_warn(dev, "Can't enable bus clock\n");
+		return err;
+	}
+
+	return 0;
+}
+
 static void
 mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
 {
@@ -130,22 +161,24 @@ mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
 static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p,
 			   struct mtk8250_data *data)
 {
-	int err;
-	struct device_node *np = pdev->dev.of_node;
-
-	data->uart_clk = of_clk_get(np, 0);
+	data->uart_clk = devm_clk_get(&pdev->dev, "baud");
 	if (IS_ERR(data->uart_clk)) {
-		dev_warn(&pdev->dev, "Can't get timer clock\n");
-		return PTR_ERR(data->uart_clk);
+		/*
+		 * For compatibility with older device trees try unnamed
+		 * clk when no baud clk can be found.
+		 */
+		data->uart_clk = devm_clk_get(&pdev->dev, NULL);
+		if (IS_ERR(data->uart_clk)) {
+			dev_warn(&pdev->dev, "Can't get uart clock\n");
+			return PTR_ERR(data->uart_clk);
+		}
+
+		return 0;
 	}
 
-	err = clk_prepare_enable(data->uart_clk);
-	if (err) {
-		dev_warn(&pdev->dev, "Can't prepare clock\n");
-		clk_put(data->uart_clk);
-		return err;
-	}
-	p->uartclk = clk_get_rate(data->uart_clk);
+	data->bus_clk = devm_clk_get(&pdev->dev, "bus");
+	if (IS_ERR(data->bus_clk))
+		return PTR_ERR(data->bus_clk);
 
 	return 0;
 }
@@ -190,19 +223,24 @@ static int mtk8250_probe(struct platform_device *pdev)
 	uart.port.regshift = 2;
 	uart.port.private_data = data;
 	uart.port.set_termios = mtk8250_set_termios;
+	uart.port.uartclk = clk_get_rate(data->uart_clk);
 
 	/* Disable Rate Fix function */
 	writel(0x0, uart.port.membase +
 			(MTK_UART_RATE_FIX << uart.port.regshift));
 
-	data->line = serial8250_register_8250_port(&uart);
-	if (data->line < 0)
-		return data->line;
-
 	platform_set_drvdata(pdev, data);
 
-	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
+	if (!pm_runtime_enabled(&pdev->dev)) {
+		err = mtk8250_runtime_resume(&pdev->dev);
+		if (err)
+			return err;
+	}
+
+	data->line = serial8250_register_8250_port(&uart);
+	if (data->line < 0)
+		return data->line;
 
 	return 0;
 }
@@ -214,13 +252,13 @@ static int mtk8250_remove(struct platform_device *pdev)
 	pm_runtime_get_sync(&pdev->dev);
 
 	serial8250_unregister_port(data->line);
-	if (!IS_ERR(data->uart_clk)) {
-		clk_disable_unprepare(data->uart_clk);
-		clk_put(data->uart_clk);
-	}
 
 	pm_runtime_disable(&pdev->dev);
 	pm_runtime_put_noidle(&pdev->dev);
+
+	if (!pm_runtime_status_suspended(&pdev->dev))
+		mtk8250_runtime_suspend(&pdev->dev);
+
 	return 0;
 }
 
@@ -244,28 +282,6 @@ static int mtk8250_resume(struct device *dev)
 }
 #endif /* CONFIG_PM_SLEEP */
 
-#ifdef CONFIG_PM
-static int mtk8250_runtime_suspend(struct device *dev)
-{
-	struct mtk8250_data *data = dev_get_drvdata(dev);
-
-	if (!IS_ERR(data->uart_clk))
-		clk_disable_unprepare(data->uart_clk);
-
-	return 0;
-}
-
-static int mtk8250_runtime_resume(struct device *dev)
-{
-	struct mtk8250_data *data = dev_get_drvdata(dev);
-
-	if (!IS_ERR(data->uart_clk))
-		clk_prepare_enable(data->uart_clk);
-
-	return 0;
-}
-#endif
-
 static const struct dev_pm_ops mtk8250_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume)
 	SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume,
@@ -289,6 +305,21 @@ static struct platform_driver mtk8250_platform_driver = {
 };
 module_platform_driver(mtk8250_platform_driver);
 
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init early_mtk8250_setup(struct earlycon_device *device,
+					const char *options)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->port.iotype = UPIO_MEM32;
+
+	return early_serial8250_setup(device, NULL);
+}
+
+OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup);
+#endif
+
 MODULE_AUTHOR("Matthias Brugger");
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Mediatek 8250 serial port driver");
diff --git a/kernel/drivers/tty/serial/8250/8250_omap.c b/kernel/drivers/tty/serial/8250/8250_omap.c
index dce1a2370..a2c0734c7 100644
--- a/kernel/drivers/tty/serial/8250/8250_omap.c
+++ b/kernel/drivers/tty/serial/8250/8250_omap.c
@@ -16,12 +16,14 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/of_gpio.h>
 #include <linux/of_irq.h>
 #include <linux/delay.h>
 #include <linux/pm_runtime.h>
 #include <linux/console.h>
 #include <linux/pm_qos.h>
+#include <linux/pm_wakeirq.h>
 #include <linux/dma-mapping.h>
 
 #include "8250.h"
@@ -31,6 +33,11 @@
 #define UART_ERRATA_i202_MDR1_ACCESS	(1 << 0)
 #define OMAP_UART_WER_HAS_TX_WAKEUP	(1 << 1)
 #define OMAP_DMA_TX_KICK		(1 << 2)
+/*
+ * See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
+ * The same errata is applicable to AM335x and DRA7x processors too.
+ */
+#define UART_ERRATA_CLOCK_DISABLE	(1 << 3)
 
 #define OMAP_UART_FCR_RX_TRIG		6
 #define OMAP_UART_FCR_TX_TRIG		4
@@ -52,6 +59,12 @@
 #define OMAP_UART_MVR_MAJ_SHIFT		8
 #define OMAP_UART_MVR_MIN_MASK		0x3f
 
+/* SYSC register bitmasks */
+#define OMAP_UART_SYSC_SOFTRESET	(1 << 1)
+
+/* SYSS register bitmasks */
+#define OMAP_UART_SYSS_RESETDONE	(1 << 0)
+
 #define UART_TI752_TLR_TX	0
 #define UART_TI752_TLR_RX	4
 
@@ -98,6 +111,8 @@ struct omap8250_priv {
 	struct pm_qos_request pm_qos_request;
 	struct work_struct qos_work;
 	struct uart_8250_dma omap8250_dma;
+	spinlock_t rx_dma_lock;
+	bool rx_dma_broken;
 };
 
 static u32 uart_read(struct uart_8250_port *up, u32 reg)
@@ -230,6 +245,15 @@ static void omap8250_update_scr(struct uart_8250_port *up,
 	serial_out(up, UART_OMAP_SCR, priv->scr);
 }
 
+static void omap8250_update_mdr1(struct uart_8250_port *up,
+				 struct omap8250_priv *priv)
+{
+	if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS)
+		omap_8250_mdr1_errataset(up, priv);
+	else
+		serial_out(up, UART_OMAP_MDR1, priv->mdr1);
+}
+
 static void omap8250_restore_regs(struct uart_8250_port *up)
 {
 	struct omap8250_priv *priv = up->port.private_data;
@@ -280,11 +304,9 @@ static void omap8250_restore_regs(struct uart_8250_port *up)
 	serial_out(up, UART_XOFF1, priv->xoff);
 
 	serial_out(up, UART_LCR, up->lcr);
-	/* need mode A for FCR */
-	if (priv->habit & UART_ERRATA_i202_MDR1_ACCESS)
-		omap_8250_mdr1_errataset(up, priv);
-	else
-		serial_out(up, UART_OMAP_MDR1, priv->mdr1);
+
+	omap8250_update_mdr1(up, priv);
+
 	up->port.ops->set_mctrl(&up->port, up->port.mctrl);
 }
 
@@ -417,7 +439,6 @@ static void omap_8250_set_termios(struct uart_port *port,
 	priv->xoff = termios->c_cc[VSTOP];
 
 	priv->efr = 0;
-	up->mcr &= ~(UART_MCR_RTS | UART_MCR_XONANY);
 	up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
 
 	if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
@@ -426,12 +447,9 @@ static void omap_8250_set_termios(struct uart_port *port,
 		priv->efr |= UART_EFR_CTS;
 	} else	if (up->port.flags & UPF_SOFT_FLOW) {
 		/*
-		 * IXON Flag:
-		 * Enable XON/XOFF flow control on input.
-		 * Receiver compares XON1, XOFF1.
+		 * OMAP rx s/w flow control is borked; the transmitter remains
+		 * stuck off even if rx flow control is subsequently disabled
 		 */
-		if (termios->c_iflag & IXON)
-			priv->efr |= OMAP_UART_SW_RX;
 
 		/*
 		 * IXOFF Flag:
@@ -442,15 +460,6 @@ static void omap_8250_set_termios(struct uart_port *port,
 			up->port.status |= UPSTAT_AUTOXOFF;
 			priv->efr |= OMAP_UART_SW_TX;
 		}
-
-		/*
-		 * IXANY Flag:
-		 * Enable any character to restart output.
-		 * Operation resumes after receiving any
-		 * character after recognition of the XOFF character
-		 */
-		if (termios->c_iflag & IXANY)
-			up->mcr |= UART_MCR_XONANY;
 	}
 	omap8250_restore_regs(up);
 
@@ -528,14 +537,14 @@ static void omap_serial_fill_features_erratas(struct uart_8250_port *up,
 
 	switch (revision) {
 	case OMAP_UART_REV_46:
-		priv->habit = UART_ERRATA_i202_MDR1_ACCESS;
+		priv->habit |= UART_ERRATA_i202_MDR1_ACCESS;
 		break;
 	case OMAP_UART_REV_52:
-		priv->habit = UART_ERRATA_i202_MDR1_ACCESS |
+		priv->habit |= UART_ERRATA_i202_MDR1_ACCESS |
 				OMAP_UART_WER_HAS_TX_WAKEUP;
 		break;
 	case OMAP_UART_REV_63:
-		priv->habit = UART_ERRATA_i202_MDR1_ACCESS |
+		priv->habit |= UART_ERRATA_i202_MDR1_ACCESS |
 			OMAP_UART_WER_HAS_TX_WAKEUP;
 		break;
 	default:
@@ -551,17 +560,6 @@ static void omap8250_uart_qos_work(struct work_struct *work)
 	pm_qos_update_request(&priv->pm_qos_request, priv->latency);
 }
 
-static irqreturn_t omap_wake_irq(int irq, void *dev_id)
-{
-	struct uart_port *port = dev_id;
-	int ret;
-
-	ret = port->handle_irq(port);
-	if (ret)
-		return IRQ_HANDLED;
-	return IRQ_NONE;
-}
-
 #ifdef CONFIG_SERIAL_8250_DMA
 static int omap_8250_dma_handle_irq(struct uart_port *port);
 #endif
@@ -595,11 +593,9 @@ static int omap_8250_startup(struct uart_port *port)
 	int ret;
 
 	if (priv->wakeirq) {
-		ret = request_irq(priv->wakeirq, omap_wake_irq,
-				  port->irqflags, "uart wakeup irq", port);
+		ret = dev_pm_set_dedicated_wake_irq(port->dev, priv->wakeirq);
 		if (ret)
 			return ret;
-		disable_irq(priv->wakeirq);
 	}
 
 	pm_runtime_get_sync(port->dev);
@@ -648,8 +644,7 @@ static int omap_8250_startup(struct uart_port *port)
 err:
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
-	if (priv->wakeirq)
-		free_irq(priv->wakeirq, port);
+	dev_pm_clear_wake_irq(port->dev);
 	return ret;
 }
 
@@ -681,10 +676,8 @@ static void omap_8250_shutdown(struct uart_port *port)
 
 	pm_runtime_mark_last_busy(port->dev);
 	pm_runtime_put_autosuspend(port->dev);
-
 	free_irq(port->irq, port);
-	if (priv->wakeirq)
-		free_irq(priv->wakeirq, port);
+	dev_pm_clear_wake_irq(port->dev);
 }
 
 static void omap_8250_throttle(struct uart_port *port)
@@ -726,22 +719,35 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir);
 
 static void __dma_rx_do_complete(struct uart_8250_port *p, bool error)
 {
+	struct omap8250_priv	*priv = p->port.private_data;
 	struct uart_8250_dma    *dma = p->dma;
 	struct tty_port         *tty_port = &p->port.state->port;
 	struct dma_tx_state     state;
 	int                     count;
+	unsigned long		flags;
+	int			ret;
 
 	dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr,
 				dma->rx_size, DMA_FROM_DEVICE);
 
+	spin_lock_irqsave(&priv->rx_dma_lock, flags);
+
+	if (!dma->rx_running)
+		goto unlock;
+
 	dma->rx_running = 0;
 	dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
 	dmaengine_terminate_all(dma->rxchan);
 
 	count = dma->rx_size - state.residue;
 
-	tty_insert_flip_string(tty_port, dma->rx_buf, count);
-	p->port.icount.rx += count;
+	ret = tty_insert_flip_string(tty_port, dma->rx_buf, count);
+
+	p->port.icount.rx += ret;
+	p->port.icount.buf_overrun += count - ret;
+unlock:
+	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+
 	if (!error)
 		omap_8250_rx_dma(p, 0);
 
@@ -753,28 +759,48 @@ static void __dma_rx_complete(void *param)
 	__dma_rx_do_complete(param, false);
 }
 
+static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
+{
+	struct omap8250_priv	*priv = p->port.private_data;
+	struct uart_8250_dma	*dma = p->dma;
+	unsigned long		flags;
+	int ret;
+
+	spin_lock_irqsave(&priv->rx_dma_lock, flags);
+
+	if (!dma->rx_running) {
+		spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+		return;
+	}
+
+	ret = dmaengine_pause(dma->rxchan);
+	if (WARN_ON_ONCE(ret))
+		priv->rx_dma_broken = true;
+
+	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+
+	__dma_rx_do_complete(p, true);
+}
+
 static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 {
+	struct omap8250_priv		*priv = p->port.private_data;
 	struct uart_8250_dma            *dma = p->dma;
+	int				err = 0;
 	struct dma_async_tx_descriptor  *desc;
+	unsigned long			flags;
 
 	switch (iir & 0x3f) {
 	case UART_IIR_RLSI:
 		/* 8250_core handles errors and break interrupts */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_do_complete(p, true);
-		}
+		omap_8250_rx_dma_flush(p);
 		return -EIO;
 	case UART_IIR_RX_TIMEOUT:
 		/*
 		 * If RCVR FIFO trigger level was not reached, complete the
 		 * transfer and let 8250_core copy the remaining data.
 		 */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_do_complete(p, true);
-		}
+		omap_8250_rx_dma_flush(p);
 		return -ETIMEDOUT;
 	case UART_IIR_RDI:
 		/*
@@ -786,24 +812,28 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 		 * the DMA won't do anything soon so we have to cancel the DMA
 		 * transfer and purge the FIFO manually.
 		 */
-		if (dma->rx_running) {
-			dmaengine_pause(dma->rxchan);
-			__dma_rx_do_complete(p, true);
-		}
+		omap_8250_rx_dma_flush(p);
 		return -ETIMEDOUT;
 
 	default:
 		break;
 	}
 
+	if (priv->rx_dma_broken)
+		return -EINVAL;
+
+	spin_lock_irqsave(&priv->rx_dma_lock, flags);
+
 	if (dma->rx_running)
-		return 0;
+		goto out;
 
 	desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
 					   dma->rx_size, DMA_DEV_TO_MEM,
 					   DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
-	if (!desc)
-		return -EBUSY;
+	if (!desc) {
+		err = -EBUSY;
+		goto out;
+	}
 
 	dma->rx_running = 1;
 	desc->callback = __dma_rx_complete;
@@ -815,7 +845,9 @@ static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 				   dma->rx_size, DMA_FROM_DEVICE);
 
 	dma_async_issue_pending(dma->rxchan);
-	return 0;
+out:
+	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
+	return err;
 }
 
 static int omap_8250_tx_dma(struct uart_8250_port *p);
@@ -1038,6 +1070,20 @@ static int omap8250_no_handle_irq(struct uart_port *port)
 	return 0;
 }
 
+static const u8 am3352_habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE;
+static const u8 am4372_habit = UART_ERRATA_CLOCK_DISABLE;
+
+static const struct of_device_id omap8250_dt_ids[] = {
+	{ .compatible = "ti,omap2-uart" },
+	{ .compatible = "ti,omap3-uart" },
+	{ .compatible = "ti,omap4-uart" },
+	{ .compatible = "ti,am3352-uart", .data = &am3352_habit, },
+	{ .compatible = "ti,am4372-uart", .data = &am4372_habit, },
+	{ .compatible = "ti,dra742-uart", .data = &am4372_habit, },
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap8250_dt_ids);
+
 static int omap8250_probe(struct platform_device *pdev)
 {
 	struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -1102,11 +1148,17 @@ static int omap8250_probe(struct platform_device *pdev)
 	up.port.unthrottle = omap_8250_unthrottle;
 
 	if (pdev->dev.of_node) {
+		const struct of_device_id *id;
+
 		ret = of_alias_get_id(pdev->dev.of_node, "serial");
 
 		of_property_read_u32(pdev->dev.of_node, "clock-frequency",
 				     &up.port.uartclk);
 		priv->wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1);
+
+		id = of_match_device(of_match_ptr(omap8250_dt_ids), &pdev->dev);
+		if (id && id->data)
+			priv->habit |= *(u8 *)id->data;
 	} else {
 		ret = pdev->id;
 	}
@@ -1129,6 +1181,8 @@ static int omap8250_probe(struct platform_device *pdev)
 			   priv->latency);
 	INIT_WORK(&priv->qos_work, omap8250_uart_qos_work);
 
+	spin_lock_init(&priv->rx_dma_lock);
+
 	device_init_wakeup(&pdev->dev, true);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, -1);
@@ -1162,6 +1216,11 @@ static int omap8250_probe(struct platform_device *pdev)
 
 			if (of_machine_is_compatible("ti,am33xx"))
 				priv->habit |= OMAP_DMA_TX_KICK;
+			/*
+			 * pause is currently not supported atleast on omap-sdma
+			 * and edma on most earlier kernels.
+			 */
+			priv->rx_dma_broken = true;
 		}
 	}
 #endif
@@ -1193,31 +1252,6 @@ static int omap8250_remove(struct platform_device *pdev)
 	return 0;
 }
 
-#ifdef CONFIG_PM
-
-static inline void omap8250_enable_wakeirq(struct omap8250_priv *priv,
-					   bool enable)
-{
-	if (!priv->wakeirq)
-		return;
-
-	if (enable)
-		enable_irq(priv->wakeirq);
-	else
-		disable_irq_nosync(priv->wakeirq);
-}
-
-static void omap8250_enable_wakeup(struct omap8250_priv *priv,
-				   bool enable)
-{
-	if (enable == priv->wakeups_enabled)
-		return;
-
-	omap8250_enable_wakeirq(priv, enable);
-	priv->wakeups_enabled = enable;
-}
-#endif
-
 #ifdef CONFIG_PM_SLEEP
 static int omap8250_prepare(struct device *dev)
 {
@@ -1244,11 +1278,6 @@ static int omap8250_suspend(struct device *dev)
 
 	serial8250_suspend_port(priv->line);
 	flush_work(&priv->qos_work);
-
-	if (device_may_wakeup(dev))
-		omap8250_enable_wakeup(priv, true);
-	else
-		omap8250_enable_wakeup(priv, false);
 	return 0;
 }
 
@@ -1256,9 +1285,6 @@ static int omap8250_resume(struct device *dev)
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
 
-	if (device_may_wakeup(dev))
-		omap8250_enable_wakeup(priv, false);
-
 	serial8250_resume_port(priv->line);
 	return 0;
 }
@@ -1272,17 +1298,46 @@ static int omap8250_lost_context(struct uart_8250_port *up)
 {
 	u32 val;
 
-	val = serial_in(up, UART_OMAP_MDR1);
+	val = serial_in(up, UART_OMAP_SCR);
 	/*
-	 * If we lose context, then MDR1 is set to its reset value which is
-	 * UART_OMAP_MDR1_DISABLE. After set_termios() we set it either to 13x
-	 * or 16x but never to disable again.
+	 * If we lose context, then SCR is set to its reset value of zero.
+	 * After set_termios() we set bit 3 of SCR (TX_EMPTY_CTL_IT) to 1,
+	 * among other bits, to never set the register back to zero again.
 	 */
-	if (val == UART_OMAP_MDR1_DISABLE)
+	if (!val)
 		return 1;
 	return 0;
 }
 
+/* TODO: in future, this should happen via API in drivers/reset/ */
+static int omap8250_soft_reset(struct device *dev)
+{
+	struct omap8250_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	int timeout = 100;
+	int sysc;
+	int syss;
+
+	sysc = serial_in(up, UART_OMAP_SYSC);
+
+	/* softreset the UART */
+	sysc |= OMAP_UART_SYSC_SOFTRESET;
+	serial_out(up, UART_OMAP_SYSC, sysc);
+
+	/* By experiments, 1us enough for reset complete on AM335x */
+	do {
+		udelay(1);
+		syss = serial_in(up, UART_OMAP_SYSS);
+	} while (--timeout && !(syss & OMAP_UART_SYSS_RESETDONE));
+
+	if (!timeout) {
+		dev_err(dev, "timed out waiting for reset done\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
 static int omap8250_runtime_suspend(struct device *dev)
 {
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
@@ -1300,8 +1355,18 @@ static int omap8250_runtime_suspend(struct device *dev)
 			return -EBUSY;
 	}
 
-	omap8250_enable_wakeup(priv, true);
-	if (up->dma)
+	if (priv->habit & UART_ERRATA_CLOCK_DISABLE) {
+		int ret;
+
+		ret = omap8250_soft_reset(dev);
+		if (ret)
+			return ret;
+
+		/* Restore to UART mode after reset (for wakeup) */
+		omap8250_update_mdr1(up, priv);
+	}
+
+	if (up->dma && up->dma->rxchan)
 		omap_8250_rx_dma(up, UART_IIR_RX_TIMEOUT);
 
 	priv->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
@@ -1321,13 +1386,12 @@ static int omap8250_runtime_resume(struct device *dev)
 		return 0;
 
 	up = serial8250_get_port(priv->line);
-	omap8250_enable_wakeup(priv, false);
 	loss_cntx = omap8250_lost_context(up);
 
 	if (loss_cntx)
 		omap8250_restore_regs(up);
 
-	if (up->dma)
+	if (up->dma && up->dma->rxchan)
 		omap_8250_rx_dma(up, 0);
 
 	priv->latency = priv->calc_latency;
@@ -1384,14 +1448,6 @@ static const struct dev_pm_ops omap8250_dev_pm_ops = {
 	.complete       = omap8250_complete,
 };
 
-static const struct of_device_id omap8250_dt_ids[] = {
-	{ .compatible = "ti,omap2-uart" },
-	{ .compatible = "ti,omap3-uart" },
-	{ .compatible = "ti,omap4-uart" },
-	{},
-};
-MODULE_DEVICE_TABLE(of, omap8250_dt_ids);
-
 static struct platform_driver omap8250_platform_driver = {
 	.driver = {
 		.name		= "omap8250",
diff --git a/kernel/drivers/tty/serial/8250/8250_pci.c b/kernel/drivers/tty/serial/8250/8250_pci.c
index 9373cca12..7cd6f9a90 100644
--- a/kernel/drivers/tty/serial/8250/8250_pci.c
+++ b/kernel/drivers/tty/serial/8250/8250_pci.c
@@ -28,7 +28,6 @@
 
 #include <linux/dmaengine.h>
 #include <linux/platform_data/dma-dw.h>
-#include <linux/platform_data/dma-hsu.h>
 
 #include "8250.h"
 
@@ -1380,6 +1379,9 @@ ce4100_serial_setup(struct serial_private *priv,
 #define PCI_DEVICE_ID_INTEL_BSW_UART1	0x228a
 #define PCI_DEVICE_ID_INTEL_BSW_UART2	0x228c
 
+#define PCI_DEVICE_ID_INTEL_BDW_UART1	0x9ce3
+#define PCI_DEVICE_ID_INTEL_BDW_UART2	0x9ce4
+
 #define BYT_PRV_CLK			0x800
 #define BYT_PRV_CLK_EN			(1 << 0)
 #define BYT_PRV_CLK_M_VAL_SHIFT		1
@@ -1417,6 +1419,10 @@ byt_set_termios(struct uart_port *p, struct ktermios *termios,
 	reg |= BYT_PRV_CLK_EN | BYT_PRV_CLK_UPDATE;
 	writel(reg, p->membase + BYT_PRV_CLK);
 
+	p->status &= ~UPSTAT_AUTOCTS;
+	if (termios->c_cflag & CRTSCTS)
+		p->status |= UPSTAT_AUTOCTS;
+
 	serial8250_do_set_termios(p, termios, old);
 }
 
@@ -1458,11 +1464,13 @@ byt_serial_setup(struct serial_private *priv,
 	switch (pdev->device) {
 	case PCI_DEVICE_ID_INTEL_BYT_UART1:
 	case PCI_DEVICE_ID_INTEL_BSW_UART1:
+	case PCI_DEVICE_ID_INTEL_BDW_UART1:
 		rx_param->src_id = 3;
 		tx_param->dst_id = 2;
 		break;
 	case PCI_DEVICE_ID_INTEL_BYT_UART2:
 	case PCI_DEVICE_ID_INTEL_BSW_UART2:
+	case PCI_DEVICE_ID_INTEL_BDW_UART2:
 		rx_param->src_id = 5;
 		tx_param->dst_id = 4;
 		break;
@@ -1504,185 +1512,77 @@ byt_serial_setup(struct serial_private *priv,
 	return ret;
 }
 
-#define INTEL_MID_UART_PS		0x30
-#define INTEL_MID_UART_MUL		0x34
-#define INTEL_MID_UART_DIV		0x38
-
-static void intel_mid_set_termios(struct uart_port *p,
-				  struct ktermios *termios,
-				  struct ktermios *old,
-				  unsigned long fref)
+static int
+pci_omegapci_setup(struct serial_private *priv,
+		      const struct pciserial_board *board,
+		      struct uart_8250_port *port, int idx)
 {
-	unsigned int baud = tty_termios_baud_rate(termios);
-	unsigned short ps = 16;
-	unsigned long fuart = baud * ps;
-	unsigned long w = BIT(24) - 1;
-	unsigned long mul, div;
-
-	if (fref < fuart) {
-		/* Find prescaler value that satisfies Fuart < Fref */
-		if (fref > baud)
-			ps = fref / baud;	/* baud rate too high */
-		else
-			ps = 1;			/* PLL case */
-		fuart = baud * ps;
-	} else {
-		/* Get Fuart closer to Fref */
-		fuart *= rounddown_pow_of_two(fref / fuart);
-	}
-
-	rational_best_approximation(fuart, fref, w, w, &mul, &div);
-	p->uartclk = fuart * 16 / ps;		/* core uses ps = 16 always */
-
-	writel(ps, p->membase + INTEL_MID_UART_PS);		/* set PS */
-	writel(mul, p->membase + INTEL_MID_UART_MUL);		/* set MUL */
-	writel(div, p->membase + INTEL_MID_UART_DIV);
-
-	serial8250_do_set_termios(p, termios, old);
+	return setup_port(priv, port, 2, idx * 8, 0);
 }
 
-static void intel_mid_set_termios_38_4M(struct uart_port *p,
-					struct ktermios *termios,
-					struct ktermios *old)
+static int
+pci_brcm_trumanage_setup(struct serial_private *priv,
+			 const struct pciserial_board *board,
+			 struct uart_8250_port *port, int idx)
 {
-	intel_mid_set_termios(p, termios, old, 38400000);
-}
+	int ret = pci_default_setup(priv, board, port, idx);
 
-static void intel_mid_set_termios_50M(struct uart_port *p,
-				      struct ktermios *termios,
-				      struct ktermios *old)
-{
-	/*
-	 * The uart clk is 50Mhz, and the baud rate come from:
-	 *      baud = 50M * MUL / (DIV * PS * DLAB)
-	 */
-	intel_mid_set_termios(p, termios, old, 50000000);
+	port->port.type = PORT_BRCM_TRUMANAGE;
+	port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
+	return ret;
 }
 
-static bool intel_mid_dma_filter(struct dma_chan *chan, void *param)
-{
-	struct hsu_dma_slave *s = param;
-
-	if (s->dma_dev != chan->device->dev || s->chan_id != chan->chan_id)
-		return false;
-
-	chan->private = s;
-	return true;
-}
+/* RTS will control by MCR if this bit is 0 */
+#define FINTEK_RTS_CONTROL_BY_HW	BIT(4)
+/* only worked with FINTEK_RTS_CONTROL_BY_HW on */
+#define FINTEK_RTS_INVERT		BIT(5)
 
-static int intel_mid_serial_setup(struct serial_private *priv,
-				  const struct pciserial_board *board,
-				  struct uart_8250_port *port, int idx,
-				  int index, struct pci_dev *dma_dev)
+/* We should do proper H/W transceiver setting before change to RS485 mode */
+static int pci_fintek_rs485_config(struct uart_port *port,
+			       struct serial_rs485 *rs485)
 {
-	struct device *dev = port->port.dev;
-	struct uart_8250_dma *dma;
-	struct hsu_dma_slave *tx_param, *rx_param;
-
-	dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL);
-	if (!dma)
-		return -ENOMEM;
-
-	tx_param = devm_kzalloc(dev, sizeof(*tx_param), GFP_KERNEL);
-	if (!tx_param)
-		return -ENOMEM;
+	u8 setting;
+	u8 *index = (u8 *) port->private_data;
+	struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev,
+						dev);
 
-	rx_param = devm_kzalloc(dev, sizeof(*rx_param), GFP_KERNEL);
-	if (!rx_param)
-		return -ENOMEM;
+	pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting);
 
-	rx_param->chan_id = index * 2 + 1;
-	tx_param->chan_id = index * 2;
-
-	dma->rxconf.src_maxburst = 64;
-	dma->txconf.dst_maxburst = 64;
-
-	rx_param->dma_dev = &dma_dev->dev;
-	tx_param->dma_dev = &dma_dev->dev;
-
-	dma->fn = intel_mid_dma_filter;
-	dma->rx_param = rx_param;
-	dma->tx_param = tx_param;
-
-	port->port.type = PORT_16750;
-	port->port.flags |= UPF_FIXED_PORT | UPF_FIXED_TYPE;
-	port->dma = dma;
+	if (!rs485)
+		rs485 = &port->rs485;
+	else if (rs485->flags & SER_RS485_ENABLED)
+		memset(rs485->padding, 0, sizeof(rs485->padding));
+	else
+		memset(rs485, 0, sizeof(*rs485));
 
-	return pci_default_setup(priv, board, port, idx);
-}
+	/* F81504/508/512 not support RTS delay before or after send */
+	rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND;
 
-#define PCI_DEVICE_ID_INTEL_PNW_UART1	0x081b
-#define PCI_DEVICE_ID_INTEL_PNW_UART2	0x081c
-#define PCI_DEVICE_ID_INTEL_PNW_UART3	0x081d
+	if (rs485->flags & SER_RS485_ENABLED) {
+		/* Enable RTS H/W control mode */
+		setting |= FINTEK_RTS_CONTROL_BY_HW;
 
-static int pnw_serial_setup(struct serial_private *priv,
-			    const struct pciserial_board *board,
-			    struct uart_8250_port *port, int idx)
-{
-	struct pci_dev *pdev = priv->dev;
-	struct pci_dev *dma_dev;
-	int index;
+		if (rs485->flags & SER_RS485_RTS_ON_SEND) {
+			/* RTS driving high on TX */
+			setting &= ~FINTEK_RTS_INVERT;
+		} else {
+			/* RTS driving low on TX */
+			setting |= FINTEK_RTS_INVERT;
+		}
 
-	switch (pdev->device) {
-	case PCI_DEVICE_ID_INTEL_PNW_UART1:
-		index = 0;
-		break;
-	case PCI_DEVICE_ID_INTEL_PNW_UART2:
-		index = 1;
-		break;
-	case PCI_DEVICE_ID_INTEL_PNW_UART3:
-		index = 2;
-		break;
-	default:
-		return -EINVAL;
+		rs485->delay_rts_after_send = 0;
+		rs485->delay_rts_before_send = 0;
+	} else {
+		/* Disable RTS H/W control mode */
+		setting &= ~(FINTEK_RTS_CONTROL_BY_HW | FINTEK_RTS_INVERT);
 	}
 
-	dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(PCI_SLOT(pdev->devfn), 3));
-
-	port->port.set_termios = intel_mid_set_termios_50M;
+	pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting);
 
-	return intel_mid_serial_setup(priv, board, port, idx, index, dma_dev);
-}
-
-#define PCI_DEVICE_ID_INTEL_TNG_UART	0x1191
-
-static int tng_serial_setup(struct serial_private *priv,
-			    const struct pciserial_board *board,
-			    struct uart_8250_port *port, int idx)
-{
-	struct pci_dev *pdev = priv->dev;
-	struct pci_dev *dma_dev;
-	int index = PCI_FUNC(pdev->devfn);
-
-	/* Currently no support for HSU port0 */
-	if (index-- == 0)
-		return -ENODEV;
-
-	dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(5, 0));
-
-	port->port.set_termios = intel_mid_set_termios_38_4M;
+	if (rs485 != &port->rs485)
+		port->rs485 = *rs485;
 
-	return intel_mid_serial_setup(priv, board, port, idx, index, dma_dev);
-}
-
-static int
-pci_omegapci_setup(struct serial_private *priv,
-		      const struct pciserial_board *board,
-		      struct uart_8250_port *port, int idx)
-{
-	return setup_port(priv, port, 2, idx * 8, 0);
-}
-
-static int
-pci_brcm_trumanage_setup(struct serial_private *priv,
-			 const struct pciserial_board *board,
-			 struct uart_8250_port *port, int idx)
-{
-	int ret = pci_default_setup(priv, board, port, idx);
-
-	port->port.type = PORT_BRCM_TRUMANAGE;
-	port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
-	return ret;
+	return 0;
 }
 
 static int pci_fintek_setup(struct serial_private *priv,
@@ -1690,6 +1590,7 @@ static int pci_fintek_setup(struct serial_private *priv,
 			    struct uart_8250_port *port, int idx)
 {
 	struct pci_dev *pdev = priv->dev;
+	u8 *data;
 	u8 config_base;
 	u16 iobase;
 
@@ -1702,6 +1603,15 @@ static int pci_fintek_setup(struct serial_private *priv,
 
 	port->port.iotype = UPIO_PORT;
 	port->port.iobase = iobase;
+	port->port.rs485_config = pci_fintek_rs485_config;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	/* preserve index in PCI configuration space */
+	*data = idx;
+	port->port.private_data = data;
 
 	return 0;
 }
@@ -1712,6 +1622,8 @@ static int pci_fintek_init(struct pci_dev *dev)
 	u32 max_port, i;
 	u32 bar_data[3];
 	u8 config_base;
+	struct serial_private *priv = pci_get_drvdata(dev);
+	struct uart_8250_port *port;
 
 	switch (dev->device) {
 	case 0x1104: /* 4 ports */
@@ -1752,6 +1664,19 @@ static int pci_fintek_init(struct pci_dev *dev)
 				(u8)((iobase & 0xff00) >> 8));
 
 		pci_write_config_byte(dev, config_base + 0x06, dev->irq);
+
+		if (priv) {
+			/* re-apply RS232/485 mode when
+			 * pciserial_resume_ports()
+			 */
+			port = serial8250_get_port(priv->line[i]);
+			pci_fintek_rs485_config(&port->port, NULL);
+		} else {
+			/* First init without port data
+			 * force init to RS232 Mode
+			 */
+			pci_write_config_byte(dev, config_base + 0x07, 0x01);
+		}
 	}
 
 	return max_port;
@@ -1823,6 +1748,9 @@ static int pci_eg20t_init(struct pci_dev *dev)
 #endif
 }
 
+#define PCI_DEVICE_ID_EXAR_XR17V4358	0x4358
+#define PCI_DEVICE_ID_EXAR_XR17V8358	0x8358
+
 static int
 pci_xr17c154_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
@@ -1832,6 +1760,15 @@ pci_xr17c154_setup(struct serial_private *priv,
 	return pci_default_setup(priv, board, port, idx);
 }
 
+static inline int
+xr17v35x_has_slave(struct serial_private *priv)
+{
+	const int dev_id = priv->dev->device;
+
+	return ((dev_id == PCI_DEVICE_ID_EXAR_XR17V4358) ||
+	        (dev_id == PCI_DEVICE_ID_EXAR_XR17V8358));
+}
+
 static int
 pci_xr17v35x_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
@@ -1846,6 +1783,13 @@ pci_xr17v35x_setup(struct serial_private *priv,
 	port->port.flags |= UPF_EXAR_EFR;
 
 	/*
+	 * Setup the uart clock for the devices on expansion slot to
+	 * half the clock speed of the main chip (which is 125MHz)
+	 */
+	if (xr17v35x_has_slave(priv) && idx >= 8)
+		port->port.uartclk = (7812500 * 16 / 2);
+
+	/*
 	 * Setup Multipurpose Input/Output pins.
 	 */
 	if (idx == 0) {
@@ -1997,8 +1941,7 @@ pci_wch_ch38x_setup(struct serial_private *priv,
 #define PCIE_VENDOR_ID_WCH		0x1c00
 #define PCIE_DEVICE_ID_WCH_CH382_2S1P	0x3250
 #define PCIE_DEVICE_ID_WCH_CH384_4S	0x3470
-
-#define PCI_DEVICE_ID_EXAR_XR17V8358	0x8358
+#define PCIE_DEVICE_ID_WCH_CH382_2S	0x3253
 
 #define PCI_VENDOR_ID_PERICOM			0x12D8
 #define PCI_DEVICE_ID_PERICOM_PI7C9X7951	0x7951
@@ -2113,42 +2056,28 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_PNW_UART1,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pnw_serial_setup,
-	},
-	{
-		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_PNW_UART2,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pnw_serial_setup,
-	},
-	{
-		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_PNW_UART3,
+		.device		= PCI_DEVICE_ID_INTEL_BSW_UART1,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
-		.setup		= pnw_serial_setup,
+		.setup		= byt_serial_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_TNG_UART,
+		.device		= PCI_DEVICE_ID_INTEL_BSW_UART2,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
-		.setup		= tng_serial_setup,
+		.setup		= byt_serial_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_BSW_UART1,
+		.device		= PCI_DEVICE_ID_INTEL_BDW_UART1,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.setup		= byt_serial_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_INTEL,
-		.device		= PCI_DEVICE_ID_INTEL_BSW_UART2,
+		.device		= PCI_DEVICE_ID_INTEL_BDW_UART2,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.setup		= byt_serial_setup,
@@ -2515,6 +2444,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 	},
 	{
 		.vendor = PCI_VENDOR_ID_EXAR,
+		.device = PCI_DEVICE_ID_EXAR_XR17V4358,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_xr17v35x_setup,
+	},
+	{
+		.vendor = PCI_VENDOR_ID_EXAR,
 		.device = PCI_DEVICE_ID_EXAR_XR17V8358,
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
@@ -2702,6 +2638,14 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.subdevice	= PCI_ANY_ID,
 		.setup		= pci_wch_ch353_setup,
 	},
+	/* WCH CH382 2S card (16850 clone) */
+	{
+		.vendor         = PCIE_VENDOR_ID_WCH,
+		.device         = PCIE_DEVICE_ID_WCH_CH382_2S,
+		.subvendor      = PCI_ANY_ID,
+		.subdevice      = PCI_ANY_ID,
+		.setup          = pci_wch_ch38x_setup,
+	},
 	/* WCH CH382 2S1P card (16850 clone) */
 	{
 		.vendor         = PCIE_VENDOR_ID_WCH,
@@ -2999,6 +2943,7 @@ enum pci_board_num_t {
 	pbn_exar_XR17V352,
 	pbn_exar_XR17V354,
 	pbn_exar_XR17V358,
+	pbn_exar_XR17V4358,
 	pbn_exar_XR17V8358,
 	pbn_exar_ibm_saturn,
 	pbn_pasemi_1682M,
@@ -3012,8 +2957,6 @@ enum pci_board_num_t {
 	pbn_ADDIDATA_PCIe_8_3906250,
 	pbn_ce4100_1_115200,
 	pbn_byt,
-	pbn_pnw,
-	pbn_tng,
 	pbn_qrk,
 	pbn_omegapci,
 	pbn_NETMOS9900_2s_115200,
@@ -3021,6 +2964,7 @@ enum pci_board_num_t {
 	pbn_fintek_4,
 	pbn_fintek_8,
 	pbn_fintek_12,
+	pbn_wch382_2,
 	pbn_wch384_4,
 	pbn_pericom_PI7C9X7951,
 	pbn_pericom_PI7C9X7952,
@@ -3690,6 +3634,14 @@ static struct pciserial_board pci_boards[] = {
 		.reg_shift	= 0,
 		.first_offset	= 0,
 	},
+	[pbn_exar_XR17V4358] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 12,
+		.base_baud	= 7812500,
+		.uart_offset	= 0x400,
+		.reg_shift	= 0,
+		.first_offset	= 0,
+	},
 	[pbn_exar_XR17V8358] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 16,
@@ -3792,16 +3744,6 @@ static struct pciserial_board pci_boards[] = {
 		.uart_offset	= 0x80,
 		.reg_shift      = 2,
 	},
-	[pbn_pnw] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 1,
-		.base_baud	= 115200,
-	},
-	[pbn_tng] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 1,
-		.base_baud	= 1843200,
-	},
 	[pbn_qrk] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
@@ -3843,6 +3785,13 @@ static struct pciserial_board pci_boards[] = {
 		.base_baud	= 115200,
 		.first_offset	= 0x40,
 	},
+	[pbn_wch382_2] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 2,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+		.first_offset	= 0xC0,
+	},
 	[pbn_wch384_4] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 4,
@@ -3890,6 +3839,13 @@ static const struct pci_device_id blacklist[] = {
 	{ PCI_DEVICE(0x4348, 0x5053), }, /* WCH CH353 1S1P */
 	{ PCI_DEVICE(0x1c00, 0x3250), }, /* WCH CH382 2S1P */
 	{ PCI_DEVICE(0x1c00, 0x3470), }, /* WCH CH384 4S */
+
+	/* Intel platforms with MID UART */
+	{ PCI_VDEVICE(INTEL, 0x081b), },
+	{ PCI_VDEVICE(INTEL, 0x081c), },
+	{ PCI_VDEVICE(INTEL, 0x081d), },
+	{ PCI_VDEVICE(INTEL, 0x1191), },
+	{ PCI_VDEVICE(INTEL, 0x19d8), },
 };
 
 /*
@@ -5133,6 +5089,10 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID,
 		0,
 		0, pbn_exar_XR17V358 },
+	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V4358,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0,
+		0, pbn_exar_XR17V4358 },
 	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V8358,
 		PCI_ANY_ID, PCI_ANY_ID,
 		0,
@@ -5582,25 +5542,15 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xff0000,
 		pbn_byt },
 
-	/*
-	 * Intel Penwell
-	 */
-	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PNW_UART1,
-		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_pnw},
-	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PNW_UART2,
-		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_pnw},
-	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PNW_UART3,
-		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_pnw},
-
-	/*
-	 * Intel Tangier
-	 */
-	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TNG_UART,
-		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_tng},
+	/* Intel Broadwell */
+	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BDW_UART1,
+		PCI_ANY_ID,  PCI_ANY_ID,
+		PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xff0000,
+		pbn_byt },
+	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BDW_UART2,
+		PCI_ANY_ID,  PCI_ANY_ID,
+		PCI_CLASS_COMMUNICATION_SERIAL << 8, 0xff0000,
+		pbn_byt },
 
 	/*
 	 * Intel Quark x1000
@@ -5641,6 +5591,10 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_b0_bt_2_115200 },
 
+	{	PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH382_2S,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0, pbn_wch382_2 },
+
 	{	PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH384_4S,
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_wch384_4 },
diff --git a/kernel/drivers/tty/serial/8250/8250_port.c b/kernel/drivers/tty/serial/8250/8250_port.c
new file mode 100644
index 000000000..5568d70ee
--- /dev/null
+++ b/kernel/drivers/tty/serial/8250/8250_port.c
@@ -0,0 +1,2935 @@
+/*
+ *  Base port operations for 8250/16550-type serial ports
+ *
+ *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *  Split from 8250_core.c, Copyright (C) 2001 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * A note about mapbase / membase
+ *
+ *  mapbase is the physical address of the IO port.
+ *  membase is an 'ioremapped' cookie.
+ */
+
+#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/ratelimit.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/nmi.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/kdb.h>
+#include <linux/uaccess.h>
+#include <linux/pm_runtime.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include "8250.h"
+
+/*
+ * Debugging.
+ */
+#if 0
+#define DEBUG_AUTOCONF(fmt...)	printk(fmt)
+#else
+#define DEBUG_AUTOCONF(fmt...)	do { } while (0)
+#endif
+
+#define BOTH_EMPTY 	(UART_LSR_TEMT | UART_LSR_THRE)
+
+/*
+ * Here we define the default xmit fifo size used for each type of UART.
+ */
+static const struct serial8250_config uart_config[] = {
+	[PORT_UNKNOWN] = {
+		.name		= "unknown",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+	},
+	[PORT_8250] = {
+		.name		= "8250",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+	},
+	[PORT_16450] = {
+		.name		= "16450",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+	},
+	[PORT_16550] = {
+		.name		= "16550",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+	},
+	[PORT_16550A] = {
+		.name		= "16550A",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO,
+	},
+	[PORT_CIRRUS] = {
+		.name		= "Cirrus",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+	},
+	[PORT_16650] = {
+		.name		= "ST16650",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+	},
+	[PORT_16650V2] = {
+		.name		= "ST16650V2",
+		.fifo_size	= 32,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
+				  UART_FCR_T_TRIG_00,
+		.rxtrig_bytes	= {8, 16, 24, 28},
+		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+	},
+	[PORT_16750] = {
+		.name		= "TI16750",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+				  UART_FCR7_64BYTE,
+		.rxtrig_bytes	= {1, 16, 32, 56},
+		.flags		= UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE,
+	},
+	[PORT_STARTECH] = {
+		.name		= "Startech",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1,
+	},
+	[PORT_16C950] = {
+		.name		= "16C950/954",
+		.fifo_size	= 128,
+		.tx_loadsz	= 128,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		/* UART_CAP_EFR breaks billionon CF bluetooth card. */
+		.flags		= UART_CAP_FIFO | UART_CAP_SLEEP,
+	},
+	[PORT_16654] = {
+		.name		= "ST16654",
+		.fifo_size	= 64,
+		.tx_loadsz	= 32,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
+				  UART_FCR_T_TRIG_10,
+		.rxtrig_bytes	= {8, 16, 56, 60},
+		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+	},
+	[PORT_16850] = {
+		.name		= "XR16850",
+		.fifo_size	= 128,
+		.tx_loadsz	= 128,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+	},
+	[PORT_RSA] = {
+		.name		= "RSA",
+		.fifo_size	= 2048,
+		.tx_loadsz	= 2048,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11,
+		.flags		= UART_CAP_FIFO,
+	},
+	[PORT_NS16550A] = {
+		.name		= "NS16550A",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_NATSEMI,
+	},
+	[PORT_XSCALE] = {
+		.name		= "XScale",
+		.fifo_size	= 32,
+		.tx_loadsz	= 32,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE,
+	},
+	[PORT_OCTEON] = {
+		.name		= "OCTEON",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO,
+	},
+	[PORT_AR7] = {
+		.name		= "AR7",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
+	[PORT_U6_16550A] = {
+		.name		= "U6_16550A",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
+	[PORT_TEGRA] = {
+		.name		= "Tegra",
+		.fifo_size	= 32,
+		.tx_loadsz	= 8,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
+				  UART_FCR_T_TRIG_01,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO | UART_CAP_RTOIE,
+	},
+	[PORT_XR17D15X] = {
+		.name		= "XR17D15X",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
+				  UART_CAP_SLEEP,
+	},
+	[PORT_XR17V35X] = {
+		.name		= "XR17V35X",
+		.fifo_size	= 256,
+		.tx_loadsz	= 256,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
+				  UART_FCR_T_TRIG_11,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
+				  UART_CAP_SLEEP,
+	},
+	[PORT_LPC3220] = {
+		.name		= "LPC3220",
+		.fifo_size	= 64,
+		.tx_loadsz	= 32,
+		.fcr		= UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
+				  UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00,
+		.flags		= UART_CAP_FIFO,
+	},
+	[PORT_BRCM_TRUMANAGE] = {
+		.name		= "TruManage",
+		.fifo_size	= 1,
+		.tx_loadsz	= 1024,
+		.flags		= UART_CAP_HFIFO,
+	},
+	[PORT_8250_CIR] = {
+		.name		= "CIR port"
+	},
+	[PORT_ALTR_16550_F32] = {
+		.name		= "Altera 16550 FIFO32",
+		.fifo_size	= 32,
+		.tx_loadsz	= 32,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
+	[PORT_ALTR_16550_F64] = {
+		.name		= "Altera 16550 FIFO64",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
+	[PORT_ALTR_16550_F128] = {
+		.name		= "Altera 16550 FIFO128",
+		.fifo_size	= 128,
+		.tx_loadsz	= 128,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
+/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
+workaround of errata A-008006 which states that tx_loadsz should  be
+configured less than Maximum supported fifo bytes */
+	[PORT_16550A_FSL64] = {
+		.name		= "16550A_FSL64",
+		.fifo_size	= 64,
+		.tx_loadsz	= 63,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+				  UART_FCR7_64BYTE,
+		.flags		= UART_CAP_FIFO,
+	},
+	[PORT_RT2880] = {
+		.name		= "Palmchip BK-3103",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO,
+	},
+};
+
+/* Uart divisor latch read */
+static int default_serial_dl_read(struct uart_8250_port *up)
+{
+	return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8;
+}
+
+/* Uart divisor latch write */
+static void default_serial_dl_write(struct uart_8250_port *up, int value)
+{
+	serial_out(up, UART_DLL, value & 0xff);
+	serial_out(up, UART_DLM, value >> 8 & 0xff);
+}
+
+#ifdef CONFIG_SERIAL_8250_RT288X
+
+/* Au1x00/RT288x UART hardware has a weird register layout */
+static const s8 au_io_in_map[8] = {
+	 0,	/* UART_RX  */
+	 2,	/* UART_IER */
+	 3,	/* UART_IIR */
+	 5,	/* UART_LCR */
+	 6,	/* UART_MCR */
+	 7,	/* UART_LSR */
+	 8,	/* UART_MSR */
+	-1,	/* UART_SCR (unmapped) */
+};
+
+static const s8 au_io_out_map[8] = {
+	 1,	/* UART_TX  */
+	 2,	/* UART_IER */
+	 4,	/* UART_FCR */
+	 5,	/* UART_LCR */
+	 6,	/* UART_MCR */
+	-1,	/* UART_LSR (unmapped) */
+	-1,	/* UART_MSR (unmapped) */
+	-1,	/* UART_SCR (unmapped) */
+};
+
+static unsigned int au_serial_in(struct uart_port *p, int offset)
+{
+	if (offset >= ARRAY_SIZE(au_io_in_map))
+		return UINT_MAX;
+	offset = au_io_in_map[offset];
+	if (offset < 0)
+		return UINT_MAX;
+	return __raw_readl(p->membase + (offset << p->regshift));
+}
+
+static void au_serial_out(struct uart_port *p, int offset, int value)
+{
+	if (offset >= ARRAY_SIZE(au_io_out_map))
+		return;
+	offset = au_io_out_map[offset];
+	if (offset < 0)
+		return;
+	__raw_writel(value, p->membase + (offset << p->regshift));
+}
+
+/* Au1x00 haven't got a standard divisor latch */
+static int au_serial_dl_read(struct uart_8250_port *up)
+{
+	return __raw_readl(up->port.membase + 0x28);
+}
+
+static void au_serial_dl_write(struct uart_8250_port *up, int value)
+{
+	__raw_writel(value, up->port.membase + 0x28);
+}
+
+#endif
+
+static unsigned int hub6_serial_in(struct uart_port *p, int offset)
+{
+	offset = offset << p->regshift;
+	outb(p->hub6 - 1 + offset, p->iobase);
+	return inb(p->iobase + 1);
+}
+
+static void hub6_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = offset << p->regshift;
+	outb(p->hub6 - 1 + offset, p->iobase);
+	outb(value, p->iobase + 1);
+}
+
+static unsigned int mem_serial_in(struct uart_port *p, int offset)
+{
+	offset = offset << p->regshift;
+	return readb(p->membase + offset);
+}
+
+static void mem_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = offset << p->regshift;
+	writeb(value, p->membase + offset);
+}
+
+static void mem32_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = offset << p->regshift;
+	writel(value, p->membase + offset);
+}
+
+static unsigned int mem32_serial_in(struct uart_port *p, int offset)
+{
+	offset = offset << p->regshift;
+	return readl(p->membase + offset);
+}
+
+static void mem32be_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = offset << p->regshift;
+	iowrite32be(value, p->membase + offset);
+}
+
+static unsigned int mem32be_serial_in(struct uart_port *p, int offset)
+{
+	offset = offset << p->regshift;
+	return ioread32be(p->membase + offset);
+}
+
+static unsigned int io_serial_in(struct uart_port *p, int offset)
+{
+	offset = offset << p->regshift;
+	return inb(p->iobase + offset);
+}
+
+static void io_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = offset << p->regshift;
+	outb(value, p->iobase + offset);
+}
+
+static int serial8250_default_handle_irq(struct uart_port *port);
+static int exar_handle_irq(struct uart_port *port);
+
+static void set_io_from_upio(struct uart_port *p)
+{
+	struct uart_8250_port *up = up_to_u8250p(p);
+
+	up->dl_read = default_serial_dl_read;
+	up->dl_write = default_serial_dl_write;
+
+	switch (p->iotype) {
+	case UPIO_HUB6:
+		p->serial_in = hub6_serial_in;
+		p->serial_out = hub6_serial_out;
+		break;
+
+	case UPIO_MEM:
+		p->serial_in = mem_serial_in;
+		p->serial_out = mem_serial_out;
+		break;
+
+	case UPIO_MEM32:
+		p->serial_in = mem32_serial_in;
+		p->serial_out = mem32_serial_out;
+		break;
+
+	case UPIO_MEM32BE:
+		p->serial_in = mem32be_serial_in;
+		p->serial_out = mem32be_serial_out;
+		break;
+
+#ifdef CONFIG_SERIAL_8250_RT288X
+	case UPIO_AU:
+		p->serial_in = au_serial_in;
+		p->serial_out = au_serial_out;
+		up->dl_read = au_serial_dl_read;
+		up->dl_write = au_serial_dl_write;
+		break;
+#endif
+
+	default:
+		p->serial_in = io_serial_in;
+		p->serial_out = io_serial_out;
+		break;
+	}
+	/* Remember loaded iotype */
+	up->cur_iotype = p->iotype;
+	p->handle_irq = serial8250_default_handle_irq;
+}
+
+static void
+serial_port_out_sync(struct uart_port *p, int offset, int value)
+{
+	switch (p->iotype) {
+	case UPIO_MEM:
+	case UPIO_MEM32:
+	case UPIO_MEM32BE:
+	case UPIO_AU:
+		p->serial_out(p, offset, value);
+		p->serial_in(p, UART_LCR);	/* safe, no side-effects */
+		break;
+	default:
+		p->serial_out(p, offset, value);
+	}
+}
+
+/*
+ * For the 16C950
+ */
+static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
+{
+	serial_out(up, UART_SCR, offset);
+	serial_out(up, UART_ICR, value);
+}
+
+static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
+{
+	unsigned int value;
+
+	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
+	serial_out(up, UART_SCR, offset);
+	value = serial_in(up, UART_ICR);
+	serial_icr_write(up, UART_ACR, up->acr);
+
+	return value;
+}
+
+/*
+ * FIFO support.
+ */
+static void serial8250_clear_fifos(struct uart_8250_port *p)
+{
+	if (p->capabilities & UART_CAP_FIFO) {
+		serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO);
+		serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO |
+			       UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+		serial_out(p, UART_FCR, 0);
+	}
+}
+
+void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p)
+{
+	serial8250_clear_fifos(p);
+	serial_out(p, UART_FCR, p->fcr);
+}
+EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
+
+void serial8250_rpm_get(struct uart_8250_port *p)
+{
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+	pm_runtime_get_sync(p->port.dev);
+}
+EXPORT_SYMBOL_GPL(serial8250_rpm_get);
+
+void serial8250_rpm_put(struct uart_8250_port *p)
+{
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+	pm_runtime_mark_last_busy(p->port.dev);
+	pm_runtime_put_autosuspend(p->port.dev);
+}
+EXPORT_SYMBOL_GPL(serial8250_rpm_put);
+
+/*
+ * These two wrappers ensure that enable_runtime_pm_tx() can be called more than
+ * once and disable_runtime_pm_tx() will still disable RPM because the fifo is
+ * empty and the HW can idle again.
+ */
+static void serial8250_rpm_get_tx(struct uart_8250_port *p)
+{
+	unsigned char rpm_active;
+
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+
+	rpm_active = xchg(&p->rpm_tx_active, 1);
+	if (rpm_active)
+		return;
+	pm_runtime_get_sync(p->port.dev);
+}
+
+static void serial8250_rpm_put_tx(struct uart_8250_port *p)
+{
+	unsigned char rpm_active;
+
+	if (!(p->capabilities & UART_CAP_RPM))
+		return;
+
+	rpm_active = xchg(&p->rpm_tx_active, 0);
+	if (!rpm_active)
+		return;
+	pm_runtime_mark_last_busy(p->port.dev);
+	pm_runtime_put_autosuspend(p->port.dev);
+}
+
+/*
+ * IER sleep support.  UARTs which have EFRs need the "extended
+ * capability" bit enabled.  Note that on XR16C850s, we need to
+ * reset LCR to write to IER.
+ */
+static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
+{
+	unsigned char lcr = 0, efr = 0;
+	/*
+	 * Exar UARTs have a SLEEP register that enables or disables
+	 * each UART to enter sleep mode separately.  On the XR17V35x the
+	 * register is accessible to each UART at the UART_EXAR_SLEEP
+	 * offset but the UART channel may only write to the corresponding
+	 * bit.
+	 */
+	serial8250_rpm_get(p);
+	if ((p->port.type == PORT_XR17V35X) ||
+	   (p->port.type == PORT_XR17D15X)) {
+		serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0);
+		goto out;
+	}
+
+	if (p->capabilities & UART_CAP_SLEEP) {
+		if (p->capabilities & UART_CAP_EFR) {
+			lcr = serial_in(p, UART_LCR);
+			efr = serial_in(p, UART_EFR);
+			serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
+			serial_out(p, UART_EFR, UART_EFR_ECB);
+			serial_out(p, UART_LCR, 0);
+		}
+		serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
+		if (p->capabilities & UART_CAP_EFR) {
+			serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
+			serial_out(p, UART_EFR, efr);
+			serial_out(p, UART_LCR, lcr);
+		}
+	}
+out:
+	serial8250_rpm_put(p);
+}
+
+#ifdef CONFIG_SERIAL_8250_RSA
+/*
+ * Attempts to turn on the RSA FIFO.  Returns zero on failure.
+ * We set the port uart clock rate if we succeed.
+ */
+static int __enable_rsa(struct uart_8250_port *up)
+{
+	unsigned char mode;
+	int result;
+
+	mode = serial_in(up, UART_RSA_MSR);
+	result = mode & UART_RSA_MSR_FIFO;
+
+	if (!result) {
+		serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
+		mode = serial_in(up, UART_RSA_MSR);
+		result = mode & UART_RSA_MSR_FIFO;
+	}
+
+	if (result)
+		up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
+
+	return result;
+}
+
+static void enable_rsa(struct uart_8250_port *up)
+{
+	if (up->port.type == PORT_RSA) {
+		if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
+			spin_lock_irq(&up->port.lock);
+			__enable_rsa(up);
+			spin_unlock_irq(&up->port.lock);
+		}
+		if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
+			serial_out(up, UART_RSA_FRR, 0);
+	}
+}
+
+/*
+ * Attempts to turn off the RSA FIFO.  Returns zero on failure.
+ * It is unknown why interrupts were disabled in here.  However,
+ * the caller is expected to preserve this behaviour by grabbing
+ * the spinlock before calling this function.
+ */
+static void disable_rsa(struct uart_8250_port *up)
+{
+	unsigned char mode;
+	int result;
+
+	if (up->port.type == PORT_RSA &&
+	    up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
+		spin_lock_irq(&up->port.lock);
+
+		mode = serial_in(up, UART_RSA_MSR);
+		result = !(mode & UART_RSA_MSR_FIFO);
+
+		if (!result) {
+			serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
+			mode = serial_in(up, UART_RSA_MSR);
+			result = !(mode & UART_RSA_MSR_FIFO);
+		}
+
+		if (result)
+			up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
+		spin_unlock_irq(&up->port.lock);
+	}
+}
+#endif /* CONFIG_SERIAL_8250_RSA */
+
+/*
+ * This is a quickie test to see how big the FIFO is.
+ * It doesn't work at all the time, more's the pity.
+ */
+static int size_fifo(struct uart_8250_port *up)
+{
+	unsigned char old_fcr, old_mcr, old_lcr;
+	unsigned short old_dl;
+	int count;
+
+	old_lcr = serial_in(up, UART_LCR);
+	serial_out(up, UART_LCR, 0);
+	old_fcr = serial_in(up, UART_FCR);
+	old_mcr = serial_in(up, UART_MCR);
+	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+		    UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+	serial_out(up, UART_MCR, UART_MCR_LOOP);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+	old_dl = serial_dl_read(up);
+	serial_dl_write(up, 0x0001);
+	serial_out(up, UART_LCR, 0x03);
+	for (count = 0; count < 256; count++)
+		serial_out(up, UART_TX, count);
+	mdelay(20);/* FIXME - schedule_timeout */
+	for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) &&
+	     (count < 256); count++)
+		serial_in(up, UART_RX);
+	serial_out(up, UART_FCR, old_fcr);
+	serial_out(up, UART_MCR, old_mcr);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+	serial_dl_write(up, old_dl);
+	serial_out(up, UART_LCR, old_lcr);
+
+	return count;
+}
+
+/*
+ * Read UART ID using the divisor method - set DLL and DLM to zero
+ * and the revision will be in DLL and device type in DLM.  We
+ * preserve the device state across this.
+ */
+static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
+{
+	unsigned char old_dll, old_dlm, old_lcr;
+	unsigned int id;
+
+	old_lcr = serial_in(p, UART_LCR);
+	serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A);
+
+	old_dll = serial_in(p, UART_DLL);
+	old_dlm = serial_in(p, UART_DLM);
+
+	serial_out(p, UART_DLL, 0);
+	serial_out(p, UART_DLM, 0);
+
+	id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8;
+
+	serial_out(p, UART_DLL, old_dll);
+	serial_out(p, UART_DLM, old_dlm);
+	serial_out(p, UART_LCR, old_lcr);
+
+	return id;
+}
+
+/*
+ * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's.
+ * When this function is called we know it is at least a StarTech
+ * 16650 V2, but it might be one of several StarTech UARTs, or one of
+ * its clones.  (We treat the broken original StarTech 16650 V1 as a
+ * 16550, and why not?  Startech doesn't seem to even acknowledge its
+ * existence.)
+ *
+ * What evil have men's minds wrought...
+ */
+static void autoconfig_has_efr(struct uart_8250_port *up)
+{
+	unsigned int id1, id2, id3, rev;
+
+	/*
+	 * Everything with an EFR has SLEEP
+	 */
+	up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
+
+	/*
+	 * First we check to see if it's an Oxford Semiconductor UART.
+	 *
+	 * If we have to do this here because some non-National
+	 * Semiconductor clone chips lock up if you try writing to the
+	 * LSR register (which serial_icr_read does)
+	 */
+
+	/*
+	 * Check for Oxford Semiconductor 16C950.
+	 *
+	 * EFR [4] must be set else this test fails.
+	 *
+	 * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca)
+	 * claims that it's needed for 952 dual UART's (which are not
+	 * recommended for new designs).
+	 */
+	up->acr = 0;
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+	serial_out(up, UART_EFR, UART_EFR_ECB);
+	serial_out(up, UART_LCR, 0x00);
+	id1 = serial_icr_read(up, UART_ID1);
+	id2 = serial_icr_read(up, UART_ID2);
+	id3 = serial_icr_read(up, UART_ID3);
+	rev = serial_icr_read(up, UART_REV);
+
+	DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev);
+
+	if (id1 == 0x16 && id2 == 0xC9 &&
+	    (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) {
+		up->port.type = PORT_16C950;
+
+		/*
+		 * Enable work around for the Oxford Semiconductor 952 rev B
+		 * chip which causes it to seriously miscalculate baud rates
+		 * when DLL is 0.
+		 */
+		if (id3 == 0x52 && rev == 0x01)
+			up->bugs |= UART_BUG_QUOT;
+		return;
+	}
+
+	/*
+	 * We check for a XR16C850 by setting DLL and DLM to 0, and then
+	 * reading back DLL and DLM.  The chip type depends on the DLM
+	 * value read back:
+	 *  0x10 - XR16C850 and the DLL contains the chip revision.
+	 *  0x12 - XR16C2850.
+	 *  0x14 - XR16C854.
+	 */
+	id1 = autoconfig_read_divisor_id(up);
+	DEBUG_AUTOCONF("850id=%04x ", id1);
+
+	id2 = id1 >> 8;
+	if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) {
+		up->port.type = PORT_16850;
+		return;
+	}
+
+	/*
+	 * It wasn't an XR16C850.
+	 *
+	 * We distinguish between the '654 and the '650 by counting
+	 * how many bytes are in the FIFO.  I'm using this for now,
+	 * since that's the technique that was sent to me in the
+	 * serial driver update, but I'm not convinced this works.
+	 * I've had problems doing this in the past.  -TYT
+	 */
+	if (size_fifo(up) == 64)
+		up->port.type = PORT_16654;
+	else
+		up->port.type = PORT_16650V2;
+}
+
+/*
+ * We detected a chip without a FIFO.  Only two fall into
+ * this category - the original 8250 and the 16450.  The
+ * 16450 has a scratch register (accessible with LCR=0)
+ */
+static void autoconfig_8250(struct uart_8250_port *up)
+{
+	unsigned char scratch, status1, status2;
+
+	up->port.type = PORT_8250;
+
+	scratch = serial_in(up, UART_SCR);
+	serial_out(up, UART_SCR, 0xa5);
+	status1 = serial_in(up, UART_SCR);
+	serial_out(up, UART_SCR, 0x5a);
+	status2 = serial_in(up, UART_SCR);
+	serial_out(up, UART_SCR, scratch);
+
+	if (status1 == 0xa5 && status2 == 0x5a)
+		up->port.type = PORT_16450;
+}
+
+static int broken_efr(struct uart_8250_port *up)
+{
+	/*
+	 * Exar ST16C2550 "A2" devices incorrectly detect as
+	 * having an EFR, and report an ID of 0x0201.  See
+	 * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html
+	 */
+	if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16)
+		return 1;
+
+	return 0;
+}
+
+/*
+ * We know that the chip has FIFOs.  Does it have an EFR?  The
+ * EFR is located in the same register position as the IIR and
+ * we know the top two bits of the IIR are currently set.  The
+ * EFR should contain zero.  Try to read the EFR.
+ */
+static void autoconfig_16550a(struct uart_8250_port *up)
+{
+	unsigned char status1, status2;
+	unsigned int iersave;
+
+	up->port.type = PORT_16550A;
+	up->capabilities |= UART_CAP_FIFO;
+
+	/*
+	 * XR17V35x UARTs have an extra divisor register, DLD
+	 * that gets enabled with when DLAB is set which will
+	 * cause the device to incorrectly match and assign
+	 * port type to PORT_16650.  The EFR for this UART is
+	 * found at offset 0x09. Instead check the Deice ID (DVID)
+	 * register for a 2, 4 or 8 port UART.
+	 */
+	if (up->port.flags & UPF_EXAR_EFR) {
+		status1 = serial_in(up, UART_EXAR_DVID);
+		if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
+			DEBUG_AUTOCONF("Exar XR17V35x ");
+			up->port.type = PORT_XR17V35X;
+			up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
+						UART_CAP_SLEEP;
+
+			return;
+		}
+
+	}
+
+	/*
+	 * Check for presence of the EFR when DLAB is set.
+	 * Only ST16C650V1 UARTs pass this test.
+	 */
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+	if (serial_in(up, UART_EFR) == 0) {
+		serial_out(up, UART_EFR, 0xA8);
+		if (serial_in(up, UART_EFR) != 0) {
+			DEBUG_AUTOCONF("EFRv1 ");
+			up->port.type = PORT_16650;
+			up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
+		} else {
+			serial_out(up, UART_LCR, 0);
+			serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+				   UART_FCR7_64BYTE);
+			status1 = serial_in(up, UART_IIR) >> 5;
+			serial_out(up, UART_FCR, 0);
+			serial_out(up, UART_LCR, 0);
+
+			if (status1 == 7)
+				up->port.type = PORT_16550A_FSL64;
+			else
+				DEBUG_AUTOCONF("Motorola 8xxx DUART ");
+		}
+		serial_out(up, UART_EFR, 0);
+		return;
+	}
+
+	/*
+	 * Maybe it requires 0xbf to be written to the LCR.
+	 * (other ST16C650V2 UARTs, TI16C752A, etc)
+	 */
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+	if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
+		DEBUG_AUTOCONF("EFRv2 ");
+		autoconfig_has_efr(up);
+		return;
+	}
+
+	/*
+	 * Check for a National Semiconductor SuperIO chip.
+	 * Attempt to switch to bank 2, read the value of the LOOP bit
+	 * from EXCR1. Switch back to bank 0, change it in MCR. Then
+	 * switch back to bank 2, read it from EXCR1 again and check
+	 * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
+	 */
+	serial_out(up, UART_LCR, 0);
+	status1 = serial_in(up, UART_MCR);
+	serial_out(up, UART_LCR, 0xE0);
+	status2 = serial_in(up, 0x02); /* EXCR1 */
+
+	if (!((status2 ^ status1) & UART_MCR_LOOP)) {
+		serial_out(up, UART_LCR, 0);
+		serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP);
+		serial_out(up, UART_LCR, 0xE0);
+		status2 = serial_in(up, 0x02); /* EXCR1 */
+		serial_out(up, UART_LCR, 0);
+		serial_out(up, UART_MCR, status1);
+
+		if ((status2 ^ status1) & UART_MCR_LOOP) {
+			unsigned short quot;
+
+			serial_out(up, UART_LCR, 0xE0);
+
+			quot = serial_dl_read(up);
+			quot <<= 3;
+
+			if (ns16550a_goto_highspeed(up))
+				serial_dl_write(up, quot);
+
+			serial_out(up, UART_LCR, 0);
+
+			up->port.uartclk = 921600*16;
+			up->port.type = PORT_NS16550A;
+			up->capabilities |= UART_NATSEMI;
+			return;
+		}
+	}
+
+	/*
+	 * No EFR.  Try to detect a TI16750, which only sets bit 5 of
+	 * the IIR when 64 byte FIFO mode is enabled when DLAB is set.
+	 * Try setting it with and without DLAB set.  Cheap clones
+	 * set bit 5 without DLAB set.
+	 */
+	serial_out(up, UART_LCR, 0);
+	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+	status1 = serial_in(up, UART_IIR) >> 5;
+	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+	status2 = serial_in(up, UART_IIR) >> 5;
+	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+	serial_out(up, UART_LCR, 0);
+
+	DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
+
+	if (status1 == 6 && status2 == 7) {
+		up->port.type = PORT_16750;
+		up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
+		return;
+	}
+
+	/*
+	 * Try writing and reading the UART_IER_UUE bit (b6).
+	 * If it works, this is probably one of the Xscale platform's
+	 * internal UARTs.
+	 * We're going to explicitly set the UUE bit to 0 before
+	 * trying to write and read a 1 just to make sure it's not
+	 * already a 1 and maybe locked there before we even start start.
+	 */
+	iersave = serial_in(up, UART_IER);
+	serial_out(up, UART_IER, iersave & ~UART_IER_UUE);
+	if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
+		/*
+		 * OK it's in a known zero state, try writing and reading
+		 * without disturbing the current state of the other bits.
+		 */
+		serial_out(up, UART_IER, iersave | UART_IER_UUE);
+		if (serial_in(up, UART_IER) & UART_IER_UUE) {
+			/*
+			 * It's an Xscale.
+			 * We'll leave the UART_IER_UUE bit set to 1 (enabled).
+			 */
+			DEBUG_AUTOCONF("Xscale ");
+			up->port.type = PORT_XSCALE;
+			up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE;
+			return;
+		}
+	} else {
+		/*
+		 * If we got here we couldn't force the IER_UUE bit to 0.
+		 * Log it and continue.
+		 */
+		DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
+	}
+	serial_out(up, UART_IER, iersave);
+
+	/*
+	 * Exar uarts have EFR in a weird location
+	 */
+	if (up->port.flags & UPF_EXAR_EFR) {
+		DEBUG_AUTOCONF("Exar XR17D15x ");
+		up->port.type = PORT_XR17D15X;
+		up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
+				    UART_CAP_SLEEP;
+
+		return;
+	}
+
+	/*
+	 * We distinguish between 16550A and U6 16550A by counting
+	 * how many bytes are in the FIFO.
+	 */
+	if (up->port.type == PORT_16550A && size_fifo(up) == 64) {
+		up->port.type = PORT_U6_16550A;
+		up->capabilities |= UART_CAP_AFE;
+	}
+}
+
+/*
+ * This routine is called by rs_init() to initialize a specific serial
+ * port.  It determines what type of UART chip this serial port is
+ * using: 8250, 16450, 16550, 16550A.  The important question is
+ * whether or not this UART is a 16550A or not, since this will
+ * determine whether or not we can use its FIFO features or not.
+ */
+static void autoconfig(struct uart_8250_port *up)
+{
+	unsigned char status1, scratch, scratch2, scratch3;
+	unsigned char save_lcr, save_mcr;
+	struct uart_port *port = &up->port;
+	unsigned long flags;
+	unsigned int old_capabilities;
+
+	if (!port->iobase && !port->mapbase && !port->membase)
+		return;
+
+	DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ",
+		       serial_index(port), port->iobase, port->membase);
+
+	/*
+	 * We really do need global IRQs disabled here - we're going to
+	 * be frobbing the chips IRQ enable register to see if it exists.
+	 */
+	spin_lock_irqsave(&port->lock, flags);
+
+	up->capabilities = 0;
+	up->bugs = 0;
+
+	if (!(port->flags & UPF_BUGGY_UART)) {
+		/*
+		 * Do a simple existence test first; if we fail this,
+		 * there's no point trying anything else.
+		 *
+		 * 0x80 is used as a nonsense port to prevent against
+		 * false positives due to ISA bus float.  The
+		 * assumption is that 0x80 is a non-existent port;
+		 * which should be safe since include/asm/io.h also
+		 * makes this assumption.
+		 *
+		 * Note: this is safe as long as MCR bit 4 is clear
+		 * and the device is in "PC" mode.
+		 */
+		scratch = serial_in(up, UART_IER);
+		serial_out(up, UART_IER, 0);
+#ifdef __i386__
+		outb(0xff, 0x080);
+#endif
+		/*
+		 * Mask out IER[7:4] bits for test as some UARTs (e.g. TL
+		 * 16C754B) allow only to modify them if an EFR bit is set.
+		 */
+		scratch2 = serial_in(up, UART_IER) & 0x0f;
+		serial_out(up, UART_IER, 0x0F);
+#ifdef __i386__
+		outb(0, 0x080);
+#endif
+		scratch3 = serial_in(up, UART_IER) & 0x0f;
+		serial_out(up, UART_IER, scratch);
+		if (scratch2 != 0 || scratch3 != 0x0F) {
+			/*
+			 * We failed; there's nothing here
+			 */
+			spin_unlock_irqrestore(&port->lock, flags);
+			DEBUG_AUTOCONF("IER test failed (%02x, %02x) ",
+				       scratch2, scratch3);
+			goto out;
+		}
+	}
+
+	save_mcr = serial_in(up, UART_MCR);
+	save_lcr = serial_in(up, UART_LCR);
+
+	/*
+	 * Check to see if a UART is really there.  Certain broken
+	 * internal modems based on the Rockwell chipset fail this
+	 * test, because they apparently don't implement the loopback
+	 * test mode.  So this test is skipped on the COM 1 through
+	 * COM 4 ports.  This *should* be safe, since no board
+	 * manufacturer would be stupid enough to design a board
+	 * that conflicts with COM 1-4 --- we hope!
+	 */
+	if (!(port->flags & UPF_SKIP_TEST)) {
+		serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A);
+		status1 = serial_in(up, UART_MSR) & 0xF0;
+		serial_out(up, UART_MCR, save_mcr);
+		if (status1 != 0x90) {
+			spin_unlock_irqrestore(&port->lock, flags);
+			DEBUG_AUTOCONF("LOOP test failed (%02x) ",
+				       status1);
+			goto out;
+		}
+	}
+
+	/*
+	 * We're pretty sure there's a port here.  Lets find out what
+	 * type of port it is.  The IIR top two bits allows us to find
+	 * out if it's 8250 or 16450, 16550, 16550A or later.  This
+	 * determines what we test for next.
+	 *
+	 * We also initialise the EFR (if any) to zero for later.  The
+	 * EFR occupies the same register location as the FCR and IIR.
+	 */
+	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+	serial_out(up, UART_EFR, 0);
+	serial_out(up, UART_LCR, 0);
+
+	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+	scratch = serial_in(up, UART_IIR) >> 6;
+
+	switch (scratch) {
+	case 0:
+		autoconfig_8250(up);
+		break;
+	case 1:
+		port->type = PORT_UNKNOWN;
+		break;
+	case 2:
+		port->type = PORT_16550;
+		break;
+	case 3:
+		autoconfig_16550a(up);
+		break;
+	}
+
+#ifdef CONFIG_SERIAL_8250_RSA
+	/*
+	 * Only probe for RSA ports if we got the region.
+	 */
+	if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA &&
+	    __enable_rsa(up))
+		port->type = PORT_RSA;
+#endif
+
+	serial_out(up, UART_LCR, save_lcr);
+
+	port->fifosize = uart_config[up->port.type].fifo_size;
+	old_capabilities = up->capabilities;
+	up->capabilities = uart_config[port->type].flags;
+	up->tx_loadsz = uart_config[port->type].tx_loadsz;
+
+	if (port->type == PORT_UNKNOWN)
+		goto out_lock;
+
+	/*
+	 * Reset the UART.
+	 */
+#ifdef CONFIG_SERIAL_8250_RSA
+	if (port->type == PORT_RSA)
+		serial_out(up, UART_RSA_FRR, 0);
+#endif
+	serial_out(up, UART_MCR, save_mcr);
+	serial8250_clear_fifos(up);
+	serial_in(up, UART_RX);
+	if (up->capabilities & UART_CAP_UUE)
+		serial_out(up, UART_IER, UART_IER_UUE);
+	else
+		serial_out(up, UART_IER, 0);
+
+out_lock:
+	spin_unlock_irqrestore(&port->lock, flags);
+	if (up->capabilities != old_capabilities) {
+		printk(KERN_WARNING
+		       "ttyS%d: detected caps %08x should be %08x\n",
+		       serial_index(port), old_capabilities,
+		       up->capabilities);
+	}
+out:
+	DEBUG_AUTOCONF("iir=%d ", scratch);
+	DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name);
+}
+
+static void autoconfig_irq(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+	unsigned char save_mcr, save_ier;
+	unsigned char save_ICP = 0;
+	unsigned int ICP = 0;
+	unsigned long irqs;
+	int irq;
+
+	if (port->flags & UPF_FOURPORT) {
+		ICP = (port->iobase & 0xfe0) | 0x1f;
+		save_ICP = inb_p(ICP);
+		outb_p(0x80, ICP);
+		inb_p(ICP);
+	}
+
+	if (uart_console(port))
+		console_lock();
+
+	/* forget possible initially masked and pending IRQ */
+	probe_irq_off(probe_irq_on());
+	save_mcr = serial_in(up, UART_MCR);
+	save_ier = serial_in(up, UART_IER);
+	serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
+
+	irqs = probe_irq_on();
+	serial_out(up, UART_MCR, 0);
+	udelay(10);
+	if (port->flags & UPF_FOURPORT) {
+		serial_out(up, UART_MCR,
+			    UART_MCR_DTR | UART_MCR_RTS);
+	} else {
+		serial_out(up, UART_MCR,
+			    UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
+	}
+	serial_out(up, UART_IER, 0x0f);	/* enable all intrs */
+	serial_in(up, UART_LSR);
+	serial_in(up, UART_RX);
+	serial_in(up, UART_IIR);
+	serial_in(up, UART_MSR);
+	serial_out(up, UART_TX, 0xFF);
+	udelay(20);
+	irq = probe_irq_off(irqs);
+
+	serial_out(up, UART_MCR, save_mcr);
+	serial_out(up, UART_IER, save_ier);
+
+	if (port->flags & UPF_FOURPORT)
+		outb_p(save_ICP, ICP);
+
+	if (uart_console(port))
+		console_unlock();
+
+	port->irq = (irq > 0) ? irq : 0;
+}
+
+static inline void __stop_tx(struct uart_8250_port *p)
+{
+	if (p->ier & UART_IER_THRI) {
+		p->ier &= ~UART_IER_THRI;
+		serial_out(p, UART_IER, p->ier);
+		serial8250_rpm_put_tx(p);
+	}
+}
+
+static void serial8250_stop_tx(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	serial8250_rpm_get(up);
+	__stop_tx(up);
+
+	/*
+	 * We really want to stop the transmitter from sending.
+	 */
+	if (port->type == PORT_16C950) {
+		up->acr |= UART_ACR_TXDIS;
+		serial_icr_write(up, UART_ACR, up->acr);
+	}
+	serial8250_rpm_put(up);
+}
+
+static void serial8250_start_tx(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	serial8250_rpm_get_tx(up);
+
+	if (up->dma && !up->dma->tx_dma(up))
+		return;
+
+	if (!(up->ier & UART_IER_THRI)) {
+		up->ier |= UART_IER_THRI;
+		serial_port_out(port, UART_IER, up->ier);
+
+		if (up->bugs & UART_BUG_TXEN) {
+			unsigned char lsr;
+			lsr = serial_in(up, UART_LSR);
+			up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+			if (lsr & UART_LSR_THRE)
+				serial8250_tx_chars(up);
+		}
+	}
+
+	/*
+	 * Re-enable the transmitter if we disabled it.
+	 */
+	if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
+		up->acr &= ~UART_ACR_TXDIS;
+		serial_icr_write(up, UART_ACR, up->acr);
+	}
+}
+
+static void serial8250_throttle(struct uart_port *port)
+{
+	port->throttle(port);
+}
+
+static void serial8250_unthrottle(struct uart_port *port)
+{
+	port->unthrottle(port);
+}
+
+static void serial8250_stop_rx(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	serial8250_rpm_get(up);
+
+	up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
+	up->port.read_status_mask &= ~UART_LSR_DR;
+	serial_port_out(port, UART_IER, up->ier);
+
+	serial8250_rpm_put(up);
+}
+
+static void serial8250_disable_ms(struct uart_port *port)
+{
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
+
+	/* no MSR capabilities */
+	if (up->bugs & UART_BUG_NOMSR)
+		return;
+
+	up->ier &= ~UART_IER_MSI;
+	serial_port_out(port, UART_IER, up->ier);
+}
+
+static void serial8250_enable_ms(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	/* no MSR capabilities */
+	if (up->bugs & UART_BUG_NOMSR)
+		return;
+
+	up->ier |= UART_IER_MSI;
+
+	serial8250_rpm_get(up);
+	serial_port_out(port, UART_IER, up->ier);
+	serial8250_rpm_put(up);
+}
+
+/*
+ * serial8250_rx_chars: processes according to the passed in LSR
+ * value, and returns the remaining LSR bits not handled
+ * by this Rx routine.
+ */
+unsigned char
+serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
+{
+	struct uart_port *port = &up->port;
+	unsigned char ch;
+	int max_count = 256;
+	char flag;
+
+	do {
+		if (likely(lsr & UART_LSR_DR))
+			ch = serial_in(up, UART_RX);
+		else
+			/*
+			 * Intel 82571 has a Serial Over Lan device that will
+			 * set UART_LSR_BI without setting UART_LSR_DR when
+			 * it receives a break. To avoid reading from the
+			 * receive buffer without UART_LSR_DR bit set, we
+			 * just force the read character to be 0
+			 */
+			ch = 0;
+
+		flag = TTY_NORMAL;
+		port->icount.rx++;
+
+		lsr |= up->lsr_saved_flags;
+		up->lsr_saved_flags = 0;
+
+		if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
+			if (lsr & UART_LSR_BI) {
+				lsr &= ~(UART_LSR_FE | UART_LSR_PE);
+				port->icount.brk++;
+				/*
+				 * We do the SysRQ and SAK checking
+				 * here because otherwise the break
+				 * may get masked by ignore_status_mask
+				 * or read_status_mask.
+				 */
+				if (uart_handle_break(port))
+					goto ignore_char;
+			} else if (lsr & UART_LSR_PE)
+				port->icount.parity++;
+			else if (lsr & UART_LSR_FE)
+				port->icount.frame++;
+			if (lsr & UART_LSR_OE)
+				port->icount.overrun++;
+
+			/*
+			 * Mask off conditions which should be ignored.
+			 */
+			lsr &= port->read_status_mask;
+
+			if (lsr & UART_LSR_BI) {
+				DEBUG_INTR("handling break....");
+				flag = TTY_BREAK;
+			} else if (lsr & UART_LSR_PE)
+				flag = TTY_PARITY;
+			else if (lsr & UART_LSR_FE)
+				flag = TTY_FRAME;
+		}
+		if (uart_handle_sysrq_char(port, ch))
+			goto ignore_char;
+
+		uart_insert_char(port, lsr, UART_LSR_OE, ch, flag);
+
+ignore_char:
+		lsr = serial_in(up, UART_LSR);
+	} while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0));
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(&port->state->port);
+	spin_lock(&port->lock);
+	return lsr;
+}
+EXPORT_SYMBOL_GPL(serial8250_rx_chars);
+
+void serial8250_tx_chars(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+	struct circ_buf *xmit = &port->state->xmit;
+	int count;
+
+	if (port->x_char) {
+		serial_out(up, UART_TX, port->x_char);
+		port->icount.tx++;
+		port->x_char = 0;
+		return;
+	}
+	if (uart_tx_stopped(port)) {
+		serial8250_stop_tx(port);
+		return;
+	}
+	if (uart_circ_empty(xmit)) {
+		__stop_tx(up);
+		return;
+	}
+
+	count = up->tx_loadsz;
+	do {
+		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+		if (up->capabilities & UART_CAP_HFIFO) {
+			if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) !=
+			    BOTH_EMPTY)
+				break;
+		}
+	} while (--count > 0);
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	DEBUG_INTR("THRE...");
+
+	/*
+	 * With RPM enabled, we have to wait until the FIFO is empty before the
+	 * HW can go idle. So we get here once again with empty FIFO and disable
+	 * the interrupt and RPM in __stop_tx()
+	 */
+	if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
+		__stop_tx(up);
+}
+EXPORT_SYMBOL_GPL(serial8250_tx_chars);
+
+/* Caller holds uart port lock */
+unsigned int serial8250_modem_status(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+	unsigned int status = serial_in(up, UART_MSR);
+
+	status |= up->msr_saved_flags;
+	up->msr_saved_flags = 0;
+	if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
+	    port->state != NULL) {
+		if (status & UART_MSR_TERI)
+			port->icount.rng++;
+		if (status & UART_MSR_DDSR)
+			port->icount.dsr++;
+		if (status & UART_MSR_DDCD)
+			uart_handle_dcd_change(port, status & UART_MSR_DCD);
+		if (status & UART_MSR_DCTS)
+			uart_handle_cts_change(port, status & UART_MSR_CTS);
+
+		wake_up_interruptible(&port->state->port.delta_msr_wait);
+	}
+
+	return status;
+}
+EXPORT_SYMBOL_GPL(serial8250_modem_status);
+
+/*
+ * This handles the interrupt from one port.
+ */
+int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
+{
+	unsigned char status;
+	unsigned long flags;
+	struct uart_8250_port *up = up_to_u8250p(port);
+	int dma_err = 0;
+
+	if (iir & UART_IIR_NO_INT)
+		return 0;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	status = serial_port_in(port, UART_LSR);
+
+	DEBUG_INTR("status = %x...", status);
+
+	if (status & (UART_LSR_DR | UART_LSR_BI)) {
+		if (up->dma)
+			dma_err = up->dma->rx_dma(up, iir);
+
+		if (!up->dma || dma_err)
+			status = serial8250_rx_chars(up, status);
+	}
+	serial8250_modem_status(up);
+	if ((!up->dma || (up->dma && up->dma->tx_err)) &&
+	    (status & UART_LSR_THRE))
+		serial8250_tx_chars(up);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+	return 1;
+}
+EXPORT_SYMBOL_GPL(serial8250_handle_irq);
+
+static int serial8250_default_handle_irq(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned int iir;
+	int ret;
+
+	serial8250_rpm_get(up);
+
+	iir = serial_port_in(port, UART_IIR);
+	ret = serial8250_handle_irq(port, iir);
+
+	serial8250_rpm_put(up);
+	return ret;
+}
+
+/*
+ * These Exar UARTs have an extra interrupt indicator that could
+ * fire for a few unimplemented interrupts.  One of which is a
+ * wakeup event when coming out of sleep.  Put this here just
+ * to be on the safe side that these interrupts don't go unhandled.
+ */
+static int exar_handle_irq(struct uart_port *port)
+{
+	unsigned char int0, int1, int2, int3;
+	unsigned int iir = serial_port_in(port, UART_IIR);
+	int ret;
+
+	ret = serial8250_handle_irq(port, iir);
+
+	if ((port->type == PORT_XR17V35X) ||
+	   (port->type == PORT_XR17D15X)) {
+		int0 = serial_port_in(port, 0x80);
+		int1 = serial_port_in(port, 0x81);
+		int2 = serial_port_in(port, 0x82);
+		int3 = serial_port_in(port, 0x83);
+	}
+
+	return ret;
+}
+
+static unsigned int serial8250_tx_empty(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned long flags;
+	unsigned int lsr;
+
+	serial8250_rpm_get(up);
+
+	spin_lock_irqsave(&port->lock, flags);
+	lsr = serial_port_in(port, UART_LSR);
+	up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	serial8250_rpm_put(up);
+
+	return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int serial8250_get_mctrl(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned int status;
+	unsigned int ret;
+
+	serial8250_rpm_get(up);
+	status = serial8250_modem_status(up);
+	serial8250_rpm_put(up);
+
+	ret = 0;
+	if (status & UART_MSR_DCD)
+		ret |= TIOCM_CAR;
+	if (status & UART_MSR_RI)
+		ret |= TIOCM_RNG;
+	if (status & UART_MSR_DSR)
+		ret |= TIOCM_DSR;
+	if (status & UART_MSR_CTS)
+		ret |= TIOCM_CTS;
+	return ret;
+}
+
+void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned char mcr = 0;
+
+	if (mctrl & TIOCM_RTS)
+		mcr |= UART_MCR_RTS;
+	if (mctrl & TIOCM_DTR)
+		mcr |= UART_MCR_DTR;
+	if (mctrl & TIOCM_OUT1)
+		mcr |= UART_MCR_OUT1;
+	if (mctrl & TIOCM_OUT2)
+		mcr |= UART_MCR_OUT2;
+	if (mctrl & TIOCM_LOOP)
+		mcr |= UART_MCR_LOOP;
+
+	mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
+
+	serial_port_out(port, UART_MCR, mcr);
+}
+EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl);
+
+static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	if (port->set_mctrl)
+		port->set_mctrl(port, mctrl);
+	else
+		serial8250_do_set_mctrl(port, mctrl);
+}
+
+static void serial8250_break_ctl(struct uart_port *port, int break_state)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned long flags;
+
+	serial8250_rpm_get(up);
+	spin_lock_irqsave(&port->lock, flags);
+	if (break_state == -1)
+		up->lcr |= UART_LCR_SBC;
+	else
+		up->lcr &= ~UART_LCR_SBC;
+	serial_port_out(port, UART_LCR, up->lcr);
+	spin_unlock_irqrestore(&port->lock, flags);
+	serial8250_rpm_put(up);
+}
+
+/*
+ *	Wait for transmitter & holding register to empty
+ */
+static void wait_for_xmitr(struct uart_8250_port *up, int bits)
+{
+	unsigned int status, tmout = 10000;
+
+	/* Wait up to 10ms for the character(s) to be sent. */
+	for (;;) {
+		status = serial_in(up, UART_LSR);
+
+		up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
+
+		if ((status & bits) == bits)
+			break;
+		if (--tmout == 0)
+			break;
+		udelay(1);
+	}
+
+	/* Wait up to 1s for flow control if necessary */
+	if (up->port.flags & UPF_CONS_FLOW) {
+		unsigned int tmout;
+		for (tmout = 1000000; tmout; tmout--) {
+			unsigned int msr = serial_in(up, UART_MSR);
+			up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
+			if (msr & UART_MSR_CTS)
+				break;
+			udelay(1);
+			touch_nmi_watchdog();
+		}
+	}
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+/*
+ * Console polling routines for writing and reading from the uart while
+ * in an interrupt or debug context.
+ */
+
+static int serial8250_get_poll_char(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned char lsr;
+	int status;
+
+	serial8250_rpm_get(up);
+
+	lsr = serial_port_in(port, UART_LSR);
+
+	if (!(lsr & UART_LSR_DR)) {
+		status = NO_POLL_CHAR;
+		goto out;
+	}
+
+	status = serial_port_in(port, UART_RX);
+out:
+	serial8250_rpm_put(up);
+	return status;
+}
+
+
+static void serial8250_put_poll_char(struct uart_port *port,
+			 unsigned char c)
+{
+	unsigned int ier;
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	serial8250_rpm_get(up);
+	/*
+	 *	First save the IER then disable the interrupts
+	 */
+	ier = serial_port_in(port, UART_IER);
+	if (up->capabilities & UART_CAP_UUE)
+		serial_port_out(port, UART_IER, UART_IER_UUE);
+	else
+		serial_port_out(port, UART_IER, 0);
+
+	wait_for_xmitr(up, BOTH_EMPTY);
+	/*
+	 *	Send the character out.
+	 */
+	serial_port_out(port, UART_TX, c);
+
+	/*
+	 *	Finally, wait for transmitter to become empty
+	 *	and restore the IER
+	 */
+	wait_for_xmitr(up, BOTH_EMPTY);
+	serial_port_out(port, UART_IER, ier);
+	serial8250_rpm_put(up);
+}
+
+#endif /* CONFIG_CONSOLE_POLL */
+
+int serial8250_do_startup(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned long flags;
+	unsigned char lsr, iir;
+	int retval;
+
+	if (!port->fifosize)
+		port->fifosize = uart_config[port->type].fifo_size;
+	if (!up->tx_loadsz)
+		up->tx_loadsz = uart_config[port->type].tx_loadsz;
+	if (!up->capabilities)
+		up->capabilities = uart_config[port->type].flags;
+	up->mcr = 0;
+
+	if (port->iotype != up->cur_iotype)
+		set_io_from_upio(port);
+
+	serial8250_rpm_get(up);
+	if (port->type == PORT_16C950) {
+		/* Wake up and initialize UART */
+		up->acr = 0;
+		serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
+		serial_port_out(port, UART_EFR, UART_EFR_ECB);
+		serial_port_out(port, UART_IER, 0);
+		serial_port_out(port, UART_LCR, 0);
+		serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
+		serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
+		serial_port_out(port, UART_EFR, UART_EFR_ECB);
+		serial_port_out(port, UART_LCR, 0);
+	}
+
+#ifdef CONFIG_SERIAL_8250_RSA
+	/*
+	 * If this is an RSA port, see if we can kick it up to the
+	 * higher speed clock.
+	 */
+	enable_rsa(up);
+#endif
+
+	if (port->type == PORT_XR17V35X) {
+		/*
+		 * First enable access to IER [7:5], ISR [5:4], FCR [5:4],
+		 * MCR [7:5] and MSR [7:0]
+		 */
+		serial_port_out(port, UART_XR_EFR, UART_EFR_ECB);
+
+		/*
+		 * Make sure all interrups are masked until initialization is
+		 * complete and the FIFOs are cleared
+		 */
+		serial_port_out(port, UART_IER, 0);
+	}
+
+	/*
+	 * Clear the FIFO buffers and disable them.
+	 * (they will be reenabled in set_termios())
+	 */
+	serial8250_clear_fifos(up);
+
+	/*
+	 * Clear the interrupt registers.
+	 */
+	serial_port_in(port, UART_LSR);
+	serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_IIR);
+	serial_port_in(port, UART_MSR);
+
+	/*
+	 * At this point, there's no way the LSR could still be 0xff;
+	 * if it is, then bail out, because there's likely no UART
+	 * here.
+	 */
+	if (!(port->flags & UPF_BUGGY_UART) &&
+	    (serial_port_in(port, UART_LSR) == 0xff)) {
+		printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
+				   serial_index(port));
+		retval = -ENODEV;
+		goto out;
+	}
+
+	/*
+	 * For a XR16C850, we need to set the trigger levels
+	 */
+	if (port->type == PORT_16850) {
+		unsigned char fctr;
+
+		serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+
+		fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
+		serial_port_out(port, UART_FCTR,
+				fctr | UART_FCTR_TRGD | UART_FCTR_RX);
+		serial_port_out(port, UART_TRG, UART_TRG_96);
+		serial_port_out(port, UART_FCTR,
+				fctr | UART_FCTR_TRGD | UART_FCTR_TX);
+		serial_port_out(port, UART_TRG, UART_TRG_96);
+
+		serial_port_out(port, UART_LCR, 0);
+	}
+
+	if (port->irq) {
+		unsigned char iir1;
+		/*
+		 * Test for UARTs that do not reassert THRE when the
+		 * transmitter is idle and the interrupt has already
+		 * been cleared.  Real 16550s should always reassert
+		 * this interrupt whenever the transmitter is idle and
+		 * the interrupt is enabled.  Delays are necessary to
+		 * allow register changes to become visible.
+		 */
+		spin_lock_irqsave(&port->lock, flags);
+		if (up->port.irqflags & IRQF_SHARED)
+			disable_irq_nosync(port->irq);
+
+		wait_for_xmitr(up, UART_LSR_THRE);
+		serial_port_out_sync(port, UART_IER, UART_IER_THRI);
+		udelay(1); /* allow THRE to set */
+		iir1 = serial_port_in(port, UART_IIR);
+		serial_port_out(port, UART_IER, 0);
+		serial_port_out_sync(port, UART_IER, UART_IER_THRI);
+		udelay(1); /* allow a working UART time to re-assert THRE */
+		iir = serial_port_in(port, UART_IIR);
+		serial_port_out(port, UART_IER, 0);
+
+		if (port->irqflags & IRQF_SHARED)
+			enable_irq(port->irq);
+		spin_unlock_irqrestore(&port->lock, flags);
+
+		/*
+		 * If the interrupt is not reasserted, or we otherwise
+		 * don't trust the iir, setup a timer to kick the UART
+		 * on a regular basis.
+		 */
+		if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) ||
+		    up->port.flags & UPF_BUG_THRE) {
+			up->bugs |= UART_BUG_THRE;
+		}
+	}
+
+	retval = up->ops->setup_irq(up);
+	if (retval)
+		goto out;
+
+	/*
+	 * Now, initialize the UART
+	 */
+	serial_port_out(port, UART_LCR, UART_LCR_WLEN8);
+
+	spin_lock_irqsave(&port->lock, flags);
+	if (up->port.flags & UPF_FOURPORT) {
+		if (!up->port.irq)
+			up->port.mctrl |= TIOCM_OUT1;
+	} else
+		/*
+		 * Most PC uarts need OUT2 raised to enable interrupts.
+		 */
+		if (port->irq)
+			up->port.mctrl |= TIOCM_OUT2;
+
+	serial8250_set_mctrl(port, port->mctrl);
+
+	/* Serial over Lan (SoL) hack:
+	   Intel 8257x Gigabit ethernet chips have a
+	   16550 emulation, to be used for Serial Over Lan.
+	   Those chips take a longer time than a normal
+	   serial device to signalize that a transmission
+	   data was queued. Due to that, the above test generally
+	   fails. One solution would be to delay the reading of
+	   iir. However, this is not reliable, since the timeout
+	   is variable. So, let's just don't test if we receive
+	   TX irq. This way, we'll never enable UART_BUG_TXEN.
+	 */
+	if (up->port.flags & UPF_NO_TXEN_TEST)
+		goto dont_test_tx_en;
+
+	/*
+	 * Do a quick test to see if we receive an
+	 * interrupt when we enable the TX irq.
+	 */
+	serial_port_out(port, UART_IER, UART_IER_THRI);
+	lsr = serial_port_in(port, UART_LSR);
+	iir = serial_port_in(port, UART_IIR);
+	serial_port_out(port, UART_IER, 0);
+
+	if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
+		if (!(up->bugs & UART_BUG_TXEN)) {
+			up->bugs |= UART_BUG_TXEN;
+			pr_debug("ttyS%d - enabling bad tx status workarounds\n",
+				 serial_index(port));
+		}
+	} else {
+		up->bugs &= ~UART_BUG_TXEN;
+	}
+
+dont_test_tx_en:
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	/*
+	 * Clear the interrupt registers again for luck, and clear the
+	 * saved flags to avoid getting false values from polling
+	 * routines or the previous session.
+	 */
+	serial_port_in(port, UART_LSR);
+	serial_port_in(port, UART_RX);
+	serial_port_in(port, UART_IIR);
+	serial_port_in(port, UART_MSR);
+	up->lsr_saved_flags = 0;
+	up->msr_saved_flags = 0;
+
+	/*
+	 * Request DMA channels for both RX and TX.
+	 */
+	if (up->dma) {
+		retval = serial8250_request_dma(up);
+		if (retval) {
+			pr_warn_ratelimited("ttyS%d - failed to request DMA\n",
+					    serial_index(port));
+			up->dma = NULL;
+		}
+	}
+
+	/*
+	 * Set the IER shadow for rx interrupts but defer actual interrupt
+	 * enable until after the FIFOs are enabled; otherwise, an already-
+	 * active sender can swamp the interrupt handler with "too much work".
+	 */
+	up->ier = UART_IER_RLSI | UART_IER_RDI;
+
+	if (port->flags & UPF_FOURPORT) {
+		unsigned int icp;
+		/*
+		 * Enable interrupts on the AST Fourport board
+		 */
+		icp = (port->iobase & 0xfe0) | 0x01f;
+		outb_p(0x80, icp);
+		inb_p(icp);
+	}
+	retval = 0;
+out:
+	serial8250_rpm_put(up);
+	return retval;
+}
+EXPORT_SYMBOL_GPL(serial8250_do_startup);
+
+static int serial8250_startup(struct uart_port *port)
+{
+	if (port->startup)
+		return port->startup(port);
+	return serial8250_do_startup(port);
+}
+
+void serial8250_do_shutdown(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned long flags;
+
+	serial8250_rpm_get(up);
+	/*
+	 * Disable interrupts from this port
+	 */
+	up->ier = 0;
+	serial_port_out(port, UART_IER, 0);
+
+	if (up->dma)
+		serial8250_release_dma(up);
+
+	spin_lock_irqsave(&port->lock, flags);
+	if (port->flags & UPF_FOURPORT) {
+		/* reset interrupts on the AST Fourport board */
+		inb((port->iobase & 0xfe0) | 0x1f);
+		port->mctrl |= TIOCM_OUT1;
+	} else
+		port->mctrl &= ~TIOCM_OUT2;
+
+	serial8250_set_mctrl(port, port->mctrl);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	/*
+	 * Disable break condition and FIFOs
+	 */
+	serial_port_out(port, UART_LCR,
+			serial_port_in(port, UART_LCR) & ~UART_LCR_SBC);
+	serial8250_clear_fifos(up);
+
+#ifdef CONFIG_SERIAL_8250_RSA
+	/*
+	 * Reset the RSA board back to 115kbps compat mode.
+	 */
+	disable_rsa(up);
+#endif
+
+	/*
+	 * Read data port to reset things, and then unlink from
+	 * the IRQ chain.
+	 */
+	serial_port_in(port, UART_RX);
+	serial8250_rpm_put(up);
+
+	up->ops->release_irq(up);
+}
+EXPORT_SYMBOL_GPL(serial8250_do_shutdown);
+
+static void serial8250_shutdown(struct uart_port *port)
+{
+	if (port->shutdown)
+		port->shutdown(port);
+	else
+		serial8250_do_shutdown(port);
+}
+
+/*
+ * XR17V35x UARTs have an extra fractional divisor register (DLD)
+ * Calculate divisor with extra 4-bit fractional portion
+ */
+static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up,
+					 unsigned int baud,
+					 unsigned int *frac)
+{
+	struct uart_port *port = &up->port;
+	unsigned int quot_16;
+
+	quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud);
+	*frac = quot_16 & 0x0f;
+
+	return quot_16 >> 4;
+}
+
+static unsigned int serial8250_get_divisor(struct uart_8250_port *up,
+					   unsigned int baud,
+					   unsigned int *frac)
+{
+	struct uart_port *port = &up->port;
+	unsigned int quot;
+
+	/*
+	 * Handle magic divisors for baud rates above baud_base on
+	 * SMSC SuperIO chips.
+	 *
+	 */
+	if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
+	    baud == (port->uartclk/4))
+		quot = 0x8001;
+	else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
+		 baud == (port->uartclk/8))
+		quot = 0x8002;
+	else if (up->port.type == PORT_XR17V35X)
+		quot = xr17v35x_get_divisor(up, baud, frac);
+	else
+		quot = uart_get_divisor(port, baud);
+
+	/*
+	 * Oxford Semi 952 rev B workaround
+	 */
+	if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
+		quot++;
+
+	return quot;
+}
+
+static unsigned char serial8250_compute_lcr(struct uart_8250_port *up,
+					    tcflag_t c_cflag)
+{
+	unsigned char cval;
+
+	switch (c_cflag & CSIZE) {
+	case CS5:
+		cval = UART_LCR_WLEN5;
+		break;
+	case CS6:
+		cval = UART_LCR_WLEN6;
+		break;
+	case CS7:
+		cval = UART_LCR_WLEN7;
+		break;
+	default:
+	case CS8:
+		cval = UART_LCR_WLEN8;
+		break;
+	}
+
+	if (c_cflag & CSTOPB)
+		cval |= UART_LCR_STOP;
+	if (c_cflag & PARENB) {
+		cval |= UART_LCR_PARITY;
+		if (up->bugs & UART_BUG_PARITY)
+			up->fifo_bug = true;
+	}
+	if (!(c_cflag & PARODD))
+		cval |= UART_LCR_EPAR;
+#ifdef CMSPAR
+	if (c_cflag & CMSPAR)
+		cval |= UART_LCR_SPAR;
+#endif
+
+	return cval;
+}
+
+static void serial8250_set_divisor(struct uart_port *port, unsigned int baud,
+			    unsigned int quot, unsigned int quot_frac)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	/* Workaround to enable 115200 baud on OMAP1510 internal ports */
+	if (is_omap1510_8250(up)) {
+		if (baud == 115200) {
+			quot = 1;
+			serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1);
+		} else
+			serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0);
+	}
+
+	/*
+	 * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2,
+	 * otherwise just set DLAB
+	 */
+	if (up->capabilities & UART_NATSEMI)
+		serial_port_out(port, UART_LCR, 0xe0);
+	else
+		serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
+
+	serial_dl_write(up, quot);
+
+	/* XR17V35x UARTs have an extra fractional divisor register (DLD) */
+	if (up->port.type == PORT_XR17V35X)
+		serial_port_out(port, 0x2, quot_frac);
+}
+
+static unsigned int
+serial8250_get_baud_rate(struct uart_port *port, struct ktermios *termios,
+			 struct ktermios *old)
+{
+	unsigned int tolerance = port->uartclk / 100;
+
+	/*
+	 * Ask the core to calculate the divisor for us.
+	 * Allow 1% tolerance at the upper limit so uart clks marginally
+	 * slower than nominal still match standard baud rates without
+	 * causing transmission errors.
+	 */
+	return uart_get_baud_rate(port, termios, old,
+				  port->uartclk / 16 / 0xffff,
+				  (port->uartclk + tolerance) / 16);
+}
+
+void
+serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
+		          struct ktermios *old)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	unsigned char cval;
+	unsigned long flags;
+	unsigned int baud, quot, frac = 0;
+
+	cval = serial8250_compute_lcr(up, termios->c_cflag);
+
+	baud = serial8250_get_baud_rate(port, termios, old);
+	quot = serial8250_get_divisor(up, baud, &frac);
+
+	/*
+	 * Ok, we're now changing the port state.  Do it with
+	 * interrupts disabled.
+	 */
+	serial8250_rpm_get(up);
+	spin_lock_irqsave(&port->lock, flags);
+
+	up->lcr = cval;					/* Save computed LCR */
+
+	if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
+		/* NOTE: If fifo_bug is not set, a user can set RX_trigger. */
+		if ((baud < 2400 && !up->dma) || up->fifo_bug) {
+			up->fcr &= ~UART_FCR_TRIGGER_MASK;
+			up->fcr |= UART_FCR_TRIGGER_1;
+		}
+	}
+
+	/*
+	 * MCR-based auto flow control.  When AFE is enabled, RTS will be
+	 * deasserted when the receive FIFO contains more characters than
+	 * the trigger, or the MCR RTS bit is cleared.  In the case where
+	 * the remote UART is not using CTS auto flow control, we must
+	 * have sufficient FIFO entries for the latency of the remote
+	 * UART to respond.  IOW, at least 32 bytes of FIFO.
+	 */
+	if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) {
+		up->mcr &= ~UART_MCR_AFE;
+		if (termios->c_cflag & CRTSCTS)
+			up->mcr |= UART_MCR_AFE;
+	}
+
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+	if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
+		port->read_status_mask |= UART_LSR_BI;
+
+	/*
+	 * Characteres to ignore
+	 */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= UART_LSR_BI;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns too (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= UART_LSR_OE;
+	}
+
+	/*
+	 * ignore all characters if CREAD is not set
+	 */
+	if ((termios->c_cflag & CREAD) == 0)
+		port->ignore_status_mask |= UART_LSR_DR;
+
+	/*
+	 * CTS flow control flag and modem status interrupts
+	 */
+	up->ier &= ~UART_IER_MSI;
+	if (!(up->bugs & UART_BUG_NOMSR) &&
+			UART_ENABLE_MS(&up->port, termios->c_cflag))
+		up->ier |= UART_IER_MSI;
+	if (up->capabilities & UART_CAP_UUE)
+		up->ier |= UART_IER_UUE;
+	if (up->capabilities & UART_CAP_RTOIE)
+		up->ier |= UART_IER_RTOIE;
+
+	serial_port_out(port, UART_IER, up->ier);
+
+	if (up->capabilities & UART_CAP_EFR) {
+		unsigned char efr = 0;
+		/*
+		 * TI16C752/Startech hardware flow control.  FIXME:
+		 * - TI16C752 requires control thresholds to be set.
+		 * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled.
+		 */
+		if (termios->c_cflag & CRTSCTS)
+			efr |= UART_EFR_CTS;
+
+		serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
+		if (port->flags & UPF_EXAR_EFR)
+			serial_port_out(port, UART_XR_EFR, efr);
+		else
+			serial_port_out(port, UART_EFR, efr);
+	}
+
+	serial8250_set_divisor(port, baud, quot, frac);
+
+	/*
+	 * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
+	 * is written without DLAB set, this mode will be disabled.
+	 */
+	if (port->type == PORT_16750)
+		serial_port_out(port, UART_FCR, up->fcr);
+
+	serial_port_out(port, UART_LCR, up->lcr);	/* reset DLAB */
+	if (port->type != PORT_16750) {
+		/* emulated UARTs (Lucent Venus 167x) need two steps */
+		if (up->fcr & UART_FCR_ENABLE_FIFO)
+			serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO);
+		serial_port_out(port, UART_FCR, up->fcr);	/* set fcr */
+	}
+	serial8250_set_mctrl(port, port->mctrl);
+	spin_unlock_irqrestore(&port->lock, flags);
+	serial8250_rpm_put(up);
+
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+}
+EXPORT_SYMBOL(serial8250_do_set_termios);
+
+static void
+serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
+		       struct ktermios *old)
+{
+	if (port->set_termios)
+		port->set_termios(port, termios, old);
+	else
+		serial8250_do_set_termios(port, termios, old);
+}
+
+static void
+serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios)
+{
+	if (termios->c_line == N_PPS) {
+		port->flags |= UPF_HARDPPS_CD;
+		spin_lock_irq(&port->lock);
+		serial8250_enable_ms(port);
+		spin_unlock_irq(&port->lock);
+	} else {
+		port->flags &= ~UPF_HARDPPS_CD;
+		if (!UART_ENABLE_MS(port, termios->c_cflag)) {
+			spin_lock_irq(&port->lock);
+			serial8250_disable_ms(port);
+			spin_unlock_irq(&port->lock);
+		}
+	}
+}
+
+
+void serial8250_do_pm(struct uart_port *port, unsigned int state,
+		      unsigned int oldstate)
+{
+	struct uart_8250_port *p = up_to_u8250p(port);
+
+	serial8250_set_sleep(p, state != 0);
+}
+EXPORT_SYMBOL(serial8250_do_pm);
+
+static void
+serial8250_pm(struct uart_port *port, unsigned int state,
+	      unsigned int oldstate)
+{
+	if (port->pm)
+		port->pm(port, state, oldstate);
+	else
+		serial8250_do_pm(port, state, oldstate);
+}
+
+static unsigned int serial8250_port_size(struct uart_8250_port *pt)
+{
+	if (pt->port.mapsize)
+		return pt->port.mapsize;
+	if (pt->port.iotype == UPIO_AU) {
+		if (pt->port.type == PORT_RT2880)
+			return 0x100;
+		return 0x1000;
+	}
+	if (is_omap1_8250(pt))
+		return 0x16 << pt->port.regshift;
+
+	return 8 << pt->port.regshift;
+}
+
+/*
+ * Resource handling.
+ */
+static int serial8250_request_std_resource(struct uart_8250_port *up)
+{
+	unsigned int size = serial8250_port_size(up);
+	struct uart_port *port = &up->port;
+	int ret = 0;
+
+	switch (port->iotype) {
+	case UPIO_AU:
+	case UPIO_TSI:
+	case UPIO_MEM32:
+	case UPIO_MEM32BE:
+	case UPIO_MEM:
+		if (!port->mapbase)
+			break;
+
+		if (!request_mem_region(port->mapbase, size, "serial")) {
+			ret = -EBUSY;
+			break;
+		}
+
+		if (port->flags & UPF_IOREMAP) {
+			port->membase = ioremap_nocache(port->mapbase, size);
+			if (!port->membase) {
+				release_mem_region(port->mapbase, size);
+				ret = -ENOMEM;
+			}
+		}
+		break;
+
+	case UPIO_HUB6:
+	case UPIO_PORT:
+		if (!request_region(port->iobase, size, "serial"))
+			ret = -EBUSY;
+		break;
+	}
+	return ret;
+}
+
+static void serial8250_release_std_resource(struct uart_8250_port *up)
+{
+	unsigned int size = serial8250_port_size(up);
+	struct uart_port *port = &up->port;
+
+	switch (port->iotype) {
+	case UPIO_AU:
+	case UPIO_TSI:
+	case UPIO_MEM32:
+	case UPIO_MEM32BE:
+	case UPIO_MEM:
+		if (!port->mapbase)
+			break;
+
+		if (port->flags & UPF_IOREMAP) {
+			iounmap(port->membase);
+			port->membase = NULL;
+		}
+
+		release_mem_region(port->mapbase, size);
+		break;
+
+	case UPIO_HUB6:
+	case UPIO_PORT:
+		release_region(port->iobase, size);
+		break;
+	}
+}
+
+static void serial8250_release_port(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	serial8250_release_std_resource(up);
+}
+
+static int serial8250_request_port(struct uart_port *port)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	return serial8250_request_std_resource(up);
+}
+
+static int fcr_get_rxtrig_bytes(struct uart_8250_port *up)
+{
+	const struct serial8250_config *conf_type = &uart_config[up->port.type];
+	unsigned char bytes;
+
+	bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)];
+
+	return bytes ? bytes : -EOPNOTSUPP;
+}
+
+static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes)
+{
+	const struct serial8250_config *conf_type = &uart_config[up->port.type];
+	int i;
+
+	if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)])
+		return -EOPNOTSUPP;
+
+	for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) {
+		if (bytes < conf_type->rxtrig_bytes[i])
+			/* Use the nearest lower value */
+			return (--i) << UART_FCR_R_TRIG_SHIFT;
+	}
+
+	return UART_FCR_R_TRIG_11;
+}
+
+static int do_get_rxtrig(struct tty_port *port)
+{
+	struct uart_state *state = container_of(port, struct uart_state, port);
+	struct uart_port *uport = state->uart_port;
+	struct uart_8250_port *up =
+		container_of(uport, struct uart_8250_port, port);
+
+	if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1)
+		return -EINVAL;
+
+	return fcr_get_rxtrig_bytes(up);
+}
+
+static int do_serial8250_get_rxtrig(struct tty_port *port)
+{
+	int rxtrig_bytes;
+
+	mutex_lock(&port->mutex);
+	rxtrig_bytes = do_get_rxtrig(port);
+	mutex_unlock(&port->mutex);
+
+	return rxtrig_bytes;
+}
+
+static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev,
+	struct device_attribute *attr, char *buf)
+{
+	struct tty_port *port = dev_get_drvdata(dev);
+	int rxtrig_bytes;
+
+	rxtrig_bytes = do_serial8250_get_rxtrig(port);
+	if (rxtrig_bytes < 0)
+		return rxtrig_bytes;
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes);
+}
+
+static int do_set_rxtrig(struct tty_port *port, unsigned char bytes)
+{
+	struct uart_state *state = container_of(port, struct uart_state, port);
+	struct uart_port *uport = state->uart_port;
+	struct uart_8250_port *up =
+		container_of(uport, struct uart_8250_port, port);
+	int rxtrig;
+
+	if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 ||
+	    up->fifo_bug)
+		return -EINVAL;
+
+	rxtrig = bytes_to_fcr_rxtrig(up, bytes);
+	if (rxtrig < 0)
+		return rxtrig;
+
+	serial8250_clear_fifos(up);
+	up->fcr &= ~UART_FCR_TRIGGER_MASK;
+	up->fcr |= (unsigned char)rxtrig;
+	serial_out(up, UART_FCR, up->fcr);
+	return 0;
+}
+
+static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes)
+{
+	int ret;
+
+	mutex_lock(&port->mutex);
+	ret = do_set_rxtrig(port, bytes);
+	mutex_unlock(&port->mutex);
+
+	return ret;
+}
+
+static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev,
+	struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct tty_port *port = dev_get_drvdata(dev);
+	unsigned char bytes;
+	int ret;
+
+	if (!count)
+		return -EINVAL;
+
+	ret = kstrtou8(buf, 10, &bytes);
+	if (ret < 0)
+		return ret;
+
+	ret = do_serial8250_set_rxtrig(port, bytes);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP,
+		   serial8250_get_attr_rx_trig_bytes,
+		   serial8250_set_attr_rx_trig_bytes);
+
+static struct attribute *serial8250_dev_attrs[] = {
+	&dev_attr_rx_trig_bytes.attr,
+	NULL,
+	};
+
+static struct attribute_group serial8250_dev_attr_group = {
+	.attrs = serial8250_dev_attrs,
+	};
+
+static void register_dev_spec_attr_grp(struct uart_8250_port *up)
+{
+	const struct serial8250_config *conf_type = &uart_config[up->port.type];
+
+	if (conf_type->rxtrig_bytes[0])
+		up->port.attr_group = &serial8250_dev_attr_group;
+}
+
+static void serial8250_config_port(struct uart_port *port, int flags)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	int ret;
+
+	/*
+	 * Find the region that we can probe for.  This in turn
+	 * tells us whether we can probe for the type of port.
+	 */
+	ret = serial8250_request_std_resource(up);
+	if (ret < 0)
+		return;
+
+	if (port->iotype != up->cur_iotype)
+		set_io_from_upio(port);
+
+	if (flags & UART_CONFIG_TYPE)
+		autoconfig(up);
+
+	/* if access method is AU, it is a 16550 with a quirk */
+	if (port->type == PORT_16550A && port->iotype == UPIO_AU)
+		up->bugs |= UART_BUG_NOMSR;
+
+	/* HW bugs may trigger IRQ while IIR == NO_INT */
+	if (port->type == PORT_TEGRA)
+		up->bugs |= UART_BUG_NOMSR;
+
+	if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
+		autoconfig_irq(up);
+
+	if (port->type == PORT_UNKNOWN)
+		serial8250_release_std_resource(up);
+
+	/* Fixme: probably not the best place for this */
+	if ((port->type == PORT_XR17V35X) ||
+	   (port->type == PORT_XR17D15X))
+		port->handle_irq = exar_handle_irq;
+
+	register_dev_spec_attr_grp(up);
+	up->fcr = uart_config[up->port.type].fcr;
+}
+
+static int
+serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	if (ser->irq >= nr_irqs || ser->irq < 0 ||
+	    ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
+	    ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS ||
+	    ser->type == PORT_STARTECH)
+		return -EINVAL;
+	return 0;
+}
+
+static const char *
+serial8250_type(struct uart_port *port)
+{
+	int type = port->type;
+
+	if (type >= ARRAY_SIZE(uart_config))
+		type = 0;
+	return uart_config[type].name;
+}
+
+static const struct uart_ops serial8250_pops = {
+	.tx_empty	= serial8250_tx_empty,
+	.set_mctrl	= serial8250_set_mctrl,
+	.get_mctrl	= serial8250_get_mctrl,
+	.stop_tx	= serial8250_stop_tx,
+	.start_tx	= serial8250_start_tx,
+	.throttle	= serial8250_throttle,
+	.unthrottle	= serial8250_unthrottle,
+	.stop_rx	= serial8250_stop_rx,
+	.enable_ms	= serial8250_enable_ms,
+	.break_ctl	= serial8250_break_ctl,
+	.startup	= serial8250_startup,
+	.shutdown	= serial8250_shutdown,
+	.set_termios	= serial8250_set_termios,
+	.set_ldisc	= serial8250_set_ldisc,
+	.pm		= serial8250_pm,
+	.type		= serial8250_type,
+	.release_port	= serial8250_release_port,
+	.request_port	= serial8250_request_port,
+	.config_port	= serial8250_config_port,
+	.verify_port	= serial8250_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_get_char = serial8250_get_poll_char,
+	.poll_put_char = serial8250_put_poll_char,
+#endif
+};
+
+void serial8250_init_port(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+
+	spin_lock_init(&port->lock);
+	port->ops = &serial8250_pops;
+
+	up->cur_iotype = 0xFF;
+}
+EXPORT_SYMBOL_GPL(serial8250_init_port);
+
+void serial8250_set_defaults(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+
+	if (up->port.flags & UPF_FIXED_TYPE) {
+		unsigned int type = up->port.type;
+
+		if (!up->port.fifosize)
+			up->port.fifosize = uart_config[type].fifo_size;
+		if (!up->tx_loadsz)
+			up->tx_loadsz = uart_config[type].tx_loadsz;
+		if (!up->capabilities)
+			up->capabilities = uart_config[type].flags;
+	}
+
+	set_io_from_upio(port);
+
+	/* default dma handlers */
+	if (up->dma) {
+		if (!up->dma->tx_dma)
+			up->dma->tx_dma = serial8250_tx_dma;
+		if (!up->dma->rx_dma)
+			up->dma->rx_dma = serial8250_rx_dma;
+	}
+}
+EXPORT_SYMBOL_GPL(serial8250_set_defaults);
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+
+static void serial8250_console_putchar(struct uart_port *port, int ch)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	wait_for_xmitr(up, UART_LSR_THRE);
+	serial_port_out(port, UART_TX, ch);
+}
+
+/*
+ *	Restore serial console when h/w power-off detected
+ */
+static void serial8250_console_restore(struct uart_8250_port *up)
+{
+	struct uart_port *port = &up->port;
+	struct ktermios termios;
+	unsigned int baud, quot, frac = 0;
+
+	termios.c_cflag = port->cons->cflag;
+	if (port->state->port.tty && termios.c_cflag == 0)
+		termios.c_cflag = port->state->port.tty->termios.c_cflag;
+
+	baud = serial8250_get_baud_rate(port, &termios, NULL);
+	quot = serial8250_get_divisor(up, baud, &frac);
+
+	serial8250_set_divisor(port, baud, quot, frac);
+	serial_port_out(port, UART_LCR, up->lcr);
+	serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
+}
+
+/*
+ *	Print a string to the serial port trying not to disturb
+ *	any possible real use of the port...
+ *
+ *	The console_lock must be held when we get here.
+ */
+void serial8250_console_write(struct uart_8250_port *up, const char *s,
+			      unsigned int count)
+{
+	struct uart_port *port = &up->port;
+	unsigned long flags;
+	unsigned int ier;
+	int locked = 1;
+
+	touch_nmi_watchdog();
+
+	serial8250_rpm_get(up);
+
+	if (port->sysrq)
+		locked = 0;
+	else if (oops_in_progress || in_kdb_printk())
+		locked = spin_trylock_irqsave(&port->lock, flags);
+	else
+		spin_lock_irqsave(&port->lock, flags);
+
+	/*
+	 *	First save the IER then disable the interrupts
+	 */
+	ier = serial_port_in(port, UART_IER);
+
+	if (up->capabilities & UART_CAP_UUE)
+		serial_port_out(port, UART_IER, UART_IER_UUE);
+	else
+		serial_port_out(port, UART_IER, 0);
+
+	/* check scratch reg to see if port powered off during system sleep */
+	if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
+		serial8250_console_restore(up);
+		up->canary = 0;
+	}
+
+	uart_console_write(port, s, count, serial8250_console_putchar);
+
+	/*
+	 *	Finally, wait for transmitter to become empty
+	 *	and restore the IER
+	 */
+	wait_for_xmitr(up, BOTH_EMPTY);
+	serial_port_out(port, UART_IER, ier);
+
+	/*
+	 *	The receive handling will happen properly because the
+	 *	receive ready bit will still be set; it is not cleared
+	 *	on read.  However, modem control will not, we must
+	 *	call it if we have saved something in the saved flags
+	 *	while processing with interrupts off.
+	 */
+	if (up->msr_saved_flags)
+		serial8250_modem_status(up);
+
+	if (locked)
+		spin_unlock_irqrestore(&port->lock, flags);
+	serial8250_rpm_put(up);
+}
+
+static unsigned int probe_baud(struct uart_port *port)
+{
+	unsigned char lcr, dll, dlm;
+	unsigned int quot;
+
+	lcr = serial_port_in(port, UART_LCR);
+	serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB);
+	dll = serial_port_in(port, UART_DLL);
+	dlm = serial_port_in(port, UART_DLM);
+	serial_port_out(port, UART_LCR, lcr);
+
+	quot = (dlm << 8) | dll;
+	return (port->uartclk / 16) / quot;
+}
+
+int serial8250_console_setup(struct uart_port *port, char *options, bool probe)
+{
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (!port->iobase && !port->membase)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+	else if (probe)
+		baud = probe_baud(port);
+
+	return uart_set_options(port, port->cons, baud, parity, bits, flow);
+}
+
+#endif /* CONFIG_SERIAL_8250_CONSOLE */
+
+MODULE_LICENSE("GPL");
diff --git a/kernel/drivers/tty/serial/8250/8250_uniphier.c b/kernel/drivers/tty/serial/8250/8250_uniphier.c
new file mode 100644
index 000000000..245edbb68
--- /dev/null
+++ b/kernel/drivers/tty/serial/8250/8250_uniphier.c
@@ -0,0 +1,262 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "8250.h"
+
+/* Most (but not all) of UniPhier UART devices have 64-depth FIFO. */
+#define UNIPHIER_UART_DEFAULT_FIFO_SIZE	64
+
+#define UNIPHIER_UART_CHAR_FCR	3	/* Character / FIFO Control Register */
+#define UNIPHIER_UART_LCR_MCR	4	/* Line/Modem Control Register */
+#define   UNIPHIER_UART_LCR_SHIFT	8
+#define UNIPHIER_UART_DLR	9	/* Divisor Latch Register */
+
+struct uniphier8250_priv {
+	int line;
+	struct clk *clk;
+	spinlock_t atomic_write_lock;
+};
+
+/*
+ * The register map is slightly different from that of 8250.
+ * IO callbacks must be overridden for correct access to FCR, LCR, and MCR.
+ */
+static unsigned int uniphier_serial_in(struct uart_port *p, int offset)
+{
+	unsigned int valshift = 0;
+
+	switch (offset) {
+	case UART_LCR:
+		valshift = UNIPHIER_UART_LCR_SHIFT;
+		/* fall through */
+	case UART_MCR:
+		offset = UNIPHIER_UART_LCR_MCR;
+		break;
+	default:
+		break;
+	}
+
+	offset <<= p->regshift;
+
+	/*
+	 * The return value must be masked with 0xff because LCR and MCR reside
+	 * in the same register that must be accessed by 32-bit write/read.
+	 * 8 or 16 bit access to this hardware result in unexpected behavior.
+	 */
+	return (readl(p->membase + offset) >> valshift) & 0xff;
+}
+
+static void uniphier_serial_out(struct uart_port *p, int offset, int value)
+{
+	unsigned int valshift = 0;
+	bool normal = false;
+
+	switch (offset) {
+	case UART_FCR:
+		offset = UNIPHIER_UART_CHAR_FCR;
+		break;
+	case UART_LCR:
+		valshift = UNIPHIER_UART_LCR_SHIFT;
+		/* Divisor latch access bit does not exist. */
+		value &= ~(UART_LCR_DLAB << valshift);
+		/* fall through */
+	case UART_MCR:
+		offset = UNIPHIER_UART_LCR_MCR;
+		break;
+	default:
+		normal = true;
+		break;
+	}
+
+	offset <<= p->regshift;
+
+	if (normal) {
+		writel(value, p->membase + offset);
+	} else {
+		/*
+		 * Special case: two registers share the same address that
+		 * must be 32-bit accessed.  As this is not longer atomic safe,
+		 * take a lock just in case.
+		 */
+		struct uniphier8250_priv *priv = p->private_data;
+		unsigned long flags;
+		u32 tmp;
+
+		spin_lock_irqsave(&priv->atomic_write_lock, flags);
+		tmp = readl(p->membase + offset);
+		tmp &= ~(0xff << valshift);
+		tmp |= value << valshift;
+		writel(tmp, p->membase + offset);
+		spin_unlock_irqrestore(&priv->atomic_write_lock, flags);
+	}
+}
+
+/*
+ * This hardware does not have the divisor latch access bit.
+ * The divisor latch register exists at different address.
+ * Override dl_read/write callbacks.
+ */
+static int uniphier_serial_dl_read(struct uart_8250_port *up)
+{
+	int offset = UNIPHIER_UART_DLR << up->port.regshift;
+
+	return readl(up->port.membase + offset);
+}
+
+static void uniphier_serial_dl_write(struct uart_8250_port *up, int value)
+{
+	int offset = UNIPHIER_UART_DLR << up->port.regshift;
+
+	writel(value, up->port.membase + offset);
+}
+
+static int uniphier_of_serial_setup(struct device *dev, struct uart_port *port,
+				    struct uniphier8250_priv *priv)
+{
+	int ret;
+	u32 prop;
+	struct device_node *np = dev->of_node;
+
+	ret = of_alias_get_id(np, "serial");
+	if (ret < 0) {
+		dev_err(dev, "failed to get alias id\n");
+		return ret;
+	}
+	port->line = priv->line = ret;
+
+	/* Get clk rate through clk driver */
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret < 0)
+		return ret;
+
+	port->uartclk = clk_get_rate(priv->clk);
+
+	/* Check for fifo size */
+	if (of_property_read_u32(np, "fifo-size", &prop) == 0)
+		port->fifosize = prop;
+	else
+		port->fifosize = UNIPHIER_UART_DEFAULT_FIFO_SIZE;
+
+	return 0;
+}
+
+static int uniphier_uart_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct uart_8250_port up;
+	struct uniphier8250_priv *priv;
+	struct resource *regs;
+	void __iomem *membase;
+	int irq;
+	int ret;
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!regs) {
+		dev_err(dev, "failed to get memory resource");
+		return -EINVAL;
+	}
+
+	membase = devm_ioremap(dev, regs->start, resource_size(regs));
+	if (!membase)
+		return -ENOMEM;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "failed to get IRQ number");
+		return irq;
+	}
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	memset(&up, 0, sizeof(up));
+
+	ret = uniphier_of_serial_setup(dev, &up.port, priv);
+	if (ret < 0)
+		return ret;
+
+	spin_lock_init(&priv->atomic_write_lock);
+
+	up.port.dev = dev;
+	up.port.private_data = priv;
+	up.port.mapbase = regs->start;
+	up.port.mapsize = resource_size(regs);
+	up.port.membase = membase;
+	up.port.irq = irq;
+
+	up.port.type = PORT_16550A;
+	up.port.iotype = UPIO_MEM32;
+	up.port.regshift = 2;
+	up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE;
+	up.capabilities = UART_CAP_FIFO;
+
+	up.port.serial_in = uniphier_serial_in;
+	up.port.serial_out = uniphier_serial_out;
+	up.dl_read = uniphier_serial_dl_read;
+	up.dl_write = uniphier_serial_dl_write;
+
+	ret = serial8250_register_8250_port(&up);
+	if (ret < 0) {
+		dev_err(dev, "failed to register 8250 port\n");
+		clk_disable_unprepare(priv->clk);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	return 0;
+}
+
+static int uniphier_uart_remove(struct platform_device *pdev)
+{
+	struct uniphier8250_priv *priv = platform_get_drvdata(pdev);
+
+	serial8250_unregister_port(priv->line);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static const struct of_device_id uniphier_uart_match[] = {
+	{ .compatible = "socionext,uniphier-uart" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_uart_match);
+
+static struct platform_driver uniphier_uart_platform_driver = {
+	.probe		= uniphier_uart_probe,
+	.remove		= uniphier_uart_remove,
+	.driver = {
+		.name	= "uniphier-uart",
+		.of_match_table = uniphier_uart_match,
+	},
+};
+module_platform_driver(uniphier_uart_platform_driver);
+
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_DESCRIPTION("UniPhier UART driver");
+MODULE_LICENSE("GPL");
diff --git a/kernel/drivers/tty/serial/8250/Kconfig b/kernel/drivers/tty/serial/8250/Kconfig
index c35070356..6412f1455 100644
--- a/kernel/drivers/tty/serial/8250/Kconfig
+++ b/kernel/drivers/tty/serial/8250/Kconfig
@@ -274,8 +274,8 @@ config SERIAL_8250_ACORN
 
 config SERIAL_8250_FSL
 	bool
-	depends on SERIAL_8250_CONSOLE && PPC_UDBG_16550
-	default PPC
+	depends on SERIAL_8250_CONSOLE
+	default PPC || ARM || ARM64
 
 config SERIAL_8250_DW
 	tristate "Support for Synopsys DesignWare 8250 quirks"
@@ -294,11 +294,12 @@ config SERIAL_8250_EM
 
 config SERIAL_8250_RT288X
 	bool "Ralink RT288x/RT305x/RT3662/RT3883 serial port support"
-	depends on SERIAL_8250 && (SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620)
+	depends on SERIAL_8250
+	default y if MIPS_ALCHEMY || SOC_RT288X || SOC_RT305X || SOC_RT3883 || SOC_MT7620
 	help
-	  If you have a Ralink RT288x/RT305x SoC based board and want to use the
-	  serial port, say Y to this option. The driver can handle up to 2 serial
-	  ports. If unsure, say N.
+	  Selecting this option will add support for the alternate register
+	  layout used by Ralink RT288x/RT305x, Alchemy Au1xxx, and some others.
+	  If unsure, say N.
 
 config SERIAL_8250_OMAP
 	tristate "Support for OMAP internal UART (8250 based driver)"
@@ -336,9 +337,44 @@ config SERIAL_8250_FINTEK
 	  LPC to 4 UART. This device has some RS485 functionality not available
 	  through the PNP driver. If unsure, say N.
 
+config SERIAL_8250_LPC18XX
+	tristate "NXP LPC18xx/43xx serial port support"
+	depends on SERIAL_8250 && OF && (ARCH_LPC18XX || COMPILE_TEST)
+	default ARCH_LPC18XX
+	help
+	  If you have a LPC18xx/43xx based board and want to use the
+	  serial port, say Y to this option. If unsure, say Y.
+
 config SERIAL_8250_MT6577
 	bool "Mediatek serial port support"
 	depends on SERIAL_8250 && ARCH_MEDIATEK
 	help
 	  If you have a Mediatek based board and want to use the
 	  serial port, say Y to this option. If unsure, say N.
+
+config SERIAL_8250_UNIPHIER
+	tristate "Support for UniPhier on-chip UART"
+	depends on SERIAL_8250 && ARCH_UNIPHIER
+	help
+	  If you have a UniPhier based board and want to use the on-chip
+	  serial ports, say Y to this option. If unsure, say N.
+
+config SERIAL_8250_INGENIC
+	bool "Support for Ingenic SoC serial ports"
+	depends on SERIAL_8250_CONSOLE && OF_FLATTREE
+	select LIBFDT
+	select SERIAL_EARLYCON
+	help
+	  If you have a system using an Ingenic SoC and wish to make use of
+	  its UARTs, say Y to this option. If unsure, say N.
+
+config SERIAL_8250_MID
+	tristate "Support for serial ports on Intel MID platforms"
+	depends on SERIAL_8250 && PCI
+	select HSU_DMA if SERIAL_8250_DMA
+	select HSU_DMA_PCI if X86_INTEL_MID
+	select RATIONAL
+	help
+	  Selecting this option will enable handling of the extra features
+	  present on the UART found on Intel Medfield SOC and various other
+	  Intel platforms.
diff --git a/kernel/drivers/tty/serial/8250/Makefile b/kernel/drivers/tty/serial/8250/Makefile
index 31e7cdc68..e177f8681 100644
--- a/kernel/drivers/tty/serial/8250/Makefile
+++ b/kernel/drivers/tty/serial/8250/Makefile
@@ -2,10 +2,11 @@
 # Makefile for the 8250 serial device drivers.
 #
 
-obj-$(CONFIG_SERIAL_8250)		+= 8250.o
+obj-$(CONFIG_SERIAL_8250)		+= 8250.o 8250_base.o
 8250-y					:= 8250_core.o
 8250-$(CONFIG_SERIAL_8250_PNP)		+= 8250_pnp.o
-8250-$(CONFIG_SERIAL_8250_DMA)		+= 8250_dma.o
+8250_base-y				:= 8250_port.o
+8250_base-$(CONFIG_SERIAL_8250_DMA)	+= 8250_dma.o
 obj-$(CONFIG_SERIAL_8250_GSC)		+= 8250_gsc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
 obj-$(CONFIG_SERIAL_8250_HP300)		+= 8250_hp300.o
@@ -22,4 +23,10 @@ obj-$(CONFIG_SERIAL_8250_DW)		+= 8250_dw.o
 obj-$(CONFIG_SERIAL_8250_EM)		+= 8250_em.o
 obj-$(CONFIG_SERIAL_8250_OMAP)		+= 8250_omap.o
 obj-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
+obj-$(CONFIG_SERIAL_8250_LPC18XX)	+= 8250_lpc18xx.o
 obj-$(CONFIG_SERIAL_8250_MT6577)	+= 8250_mtk.o
+obj-$(CONFIG_SERIAL_8250_UNIPHIER)	+= 8250_uniphier.o
+obj-$(CONFIG_SERIAL_8250_INGENIC)	+= 8250_ingenic.o
+obj-$(CONFIG_SERIAL_8250_MID)		+= 8250_mid.o
+
+CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt