diff options
author | Yunhong Jiang <yunhong.jiang@intel.com> | 2015-08-04 12:17:53 -0700 |
---|---|---|
committer | Yunhong Jiang <yunhong.jiang@intel.com> | 2015-08-04 15:44:42 -0700 |
commit | 9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00 (patch) | |
tree | 1c9cafbcd35f783a87880a10f85d1a060db1a563 /kernel/drivers/staging/comedi/drivers/jr3_pci.h | |
parent | 98260f3884f4a202f9ca5eabed40b1354c489b29 (diff) |
Add the rt linux 4.1.3-rt3 as base
Import the rt linux 4.1.3-rt3 as OPNFV kvm base.
It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:
commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date: Sat Jul 25 12:13:34 2015 +0200
Prepare v4.1.3-rt3
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.
Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Diffstat (limited to 'kernel/drivers/staging/comedi/drivers/jr3_pci.h')
-rw-r--r-- | kernel/drivers/staging/comedi/drivers/jr3_pci.h | 682 |
1 files changed, 682 insertions, 0 deletions
diff --git a/kernel/drivers/staging/comedi/drivers/jr3_pci.h b/kernel/drivers/staging/comedi/drivers/jr3_pci.h new file mode 100644 index 000000000..356811def --- /dev/null +++ b/kernel/drivers/staging/comedi/drivers/jr3_pci.h @@ -0,0 +1,682 @@ +/* Helper types to take care of the fact that the DSP card memory + * is 16 bits, but aligned on a 32 bit PCI boundary + */ + +static inline u16 get_u16(const u32 __iomem *p) +{ + return (u16)readl(p); +} + +static inline void set_u16(u32 __iomem *p, u16 val) +{ + writel(val, p); +} + +static inline s16 get_s16(const s32 __iomem *p) +{ + return (s16)readl(p); +} + +static inline void set_s16(s32 __iomem *p, s16 val) +{ + writel(val, p); +} + +/* The raw data is stored in a format which facilitates rapid + * processing by the JR3 DSP chip. The raw_channel structure shows the + * format for a single channel of data. Each channel takes four, + * two-byte words. + * + * Raw_time is an unsigned integer which shows the value of the JR3 + * DSP's internal clock at the time the sample was received. The clock + * runs at 1/10 the JR3 DSP cycle time. JR3's slowest DSP runs at 10 + * Mhz. At 10 Mhz raw_time would therefore clock at 1 Mhz. + * + * Raw_data is the raw data received directly from the sensor. The + * sensor data stream is capable of representing 16 different + * channels. Channel 0 shows the excitation voltage at the sensor. It + * is used to regulate the voltage over various cable lengths. + * Channels 1-6 contain the coupled force data Fx through Mz. Channel + * 7 contains the sensor's calibration data. The use of channels 8-15 + * varies with different sensors. + */ + +struct raw_channel { + u32 raw_time; + s32 raw_data; + s32 reserved[2]; +}; + +/* The force_array structure shows the layout for the decoupled and + * filtered force data. + */ +struct force_array { + s32 fx; + s32 fy; + s32 fz; + s32 mx; + s32 my; + s32 mz; + s32 v1; + s32 v2; +}; + +/* The six_axis_array structure shows the layout for the offsets and + * the full scales. + */ +struct six_axis_array { + s32 fx; + s32 fy; + s32 fz; + s32 mx; + s32 my; + s32 mz; +}; + +/* VECT_BITS */ +/* The vect_bits structure shows the layout for indicating + * which axes to use in computing the vectors. Each bit signifies + * selection of a single axis. The V1x axis bit corresponds to a hex + * value of 0x0001 and the V2z bit corresponds to a hex value of + * 0x0020. Example: to specify the axes V1x, V1y, V2x, and V2z the + * pattern would be 0x002b. Vector 1 defaults to a force vector and + * vector 2 defaults to a moment vector. It is possible to change one + * or the other so that two force vectors or two moment vectors are + * calculated. Setting the changeV1 bit or the changeV2 bit will + * change that vector to be the opposite of its default. Therefore to + * have two force vectors, set changeV1 to 1. + */ + +/* vect_bits appears to be unused at this time */ +enum { + fx = 0x0001, + fy = 0x0002, + fz = 0x0004, + mx = 0x0008, + my = 0x0010, + mz = 0x0020, + changeV2 = 0x0040, + changeV1 = 0x0080 +}; + +/* WARNING_BITS */ +/* The warning_bits structure shows the bit pattern for the warning + * word. The bit fields are shown from bit 0 (lsb) to bit 15 (msb). + */ + +/* XX_NEAR_SET */ +/* The xx_near_sat bits signify that the indicated axis has reached or + * exceeded the near saturation value. + */ + +enum { + fx_near_sat = 0x0001, + fy_near_sat = 0x0002, + fz_near_sat = 0x0004, + mx_near_sat = 0x0008, + my_near_sat = 0x0010, + mz_near_sat = 0x0020 +}; + +/* ERROR_BITS */ +/* XX_SAT */ +/* MEMORY_ERROR */ +/* SENSOR_CHANGE */ + +/* The error_bits structure shows the bit pattern for the error word. + * The bit fields are shown from bit 0 (lsb) to bit 15 (msb). The + * xx_sat bits signify that the indicated axis has reached or exceeded + * the saturation value. The memory_error bit indicates that a problem + * was detected in the on-board RAM during the power-up + * initialization. The sensor_change bit indicates that a sensor other + * than the one originally plugged in has passed its CRC check. This + * bit latches, and must be reset by the user. + * + */ + +/* SYSTEM_BUSY */ + +/* The system_busy bit indicates that the JR3 DSP is currently busy + * and is not calculating force data. This occurs when a new + * coordinate transformation, or new sensor full scale is set by the + * user. A very fast system using the force data for feedback might + * become unstable during the approximately 4 ms needed to accomplish + * these calculations. This bit will also become active when a new + * sensor is plugged in and the system needs to recalculate the + * calibration CRC. + */ + +/* CAL_CRC_BAD */ + +/* The cal_crc_bad bit indicates that the calibration CRC has not + * calculated to zero. CRC is short for cyclic redundancy code. It is + * a method for determining the integrity of messages in data + * communication. The calibration data stored inside the sensor is + * transmitted to the JR3 DSP along with the sensor data. The + * calibration data has a CRC attached to the end of it, to assist in + * determining the completeness and integrity of the calibration data + * received from the sensor. There are two reasons the CRC may not + * have calculated to zero. The first is that all the calibration data + * has not yet been received, the second is that the calibration data + * has been corrupted. A typical sensor transmits the entire contents + * of its calibration matrix over 30 times a second. Therefore, if + * this bit is not zero within a couple of seconds after the sensor + * has been plugged in, there is a problem with the sensor's + * calibration data. + */ + +/* WATCH_DOG */ +/* WATCH_DOG2 */ + +/* The watch_dog and watch_dog2 bits are sensor, not processor, watch + * dog bits. Watch_dog indicates that the sensor data line seems to be + * acting correctly, while watch_dog2 indicates that sensor data and + * clock are being received. It is possible for watch_dog2 to go off + * while watch_dog does not. This would indicate an improper clock + * signal, while data is acting correctly. If either watch dog barks, + * the sensor data is not being received correctly. + */ + +enum error_bits_t { + fx_sat = 0x0001, + fy_sat = 0x0002, + fz_sat = 0x0004, + mx_sat = 0x0008, + my_sat = 0x0010, + mz_sat = 0x0020, + memory_error = 0x0400, + sensor_change = 0x0800, + system_busy = 0x1000, + cal_crc_bad = 0x2000, + watch_dog2 = 0x4000, + watch_dog = 0x8000 +}; + +/* THRESH_STRUCT */ + +/* This structure shows the layout for a single threshold packet inside of a + * load envelope. Each load envelope can contain several threshold structures. + * 1. data_address contains the address of the data for that threshold. This + * includes filtered, unfiltered, raw, rate, counters, error and warning data + * 2. threshold is the is the value at which, if data is above or below, the + * bits will be set ... (pag.24). + * 3. bit_pattern contains the bits that will be set if the threshold value is + * met or exceeded. + */ + +struct thresh_struct { + s32 data_address; + s32 threshold; + s32 bit_pattern; +}; + +/* LE_STRUCT */ + +/* Layout of a load enveloped packet. Four thresholds are showed ... for more + * see manual (pag.25) + * 1. latch_bits is a bit pattern that show which bits the user wants to latch. + * The latched bits will not be reset once the threshold which set them is + * no longer true. In that case the user must reset them using the reset_bit + * command. + * 2. number_of_xx_thresholds specify how many GE/LE threshold there are. + */ +struct le_struct { + s32 latch_bits; + s32 number_of_ge_thresholds; + s32 number_of_le_thresholds; + struct thresh_struct thresholds[4]; + s32 reserved; +}; + +/* LINK_TYPES */ +/* Link types is an enumerated value showing the different possible transform + * link types. + * 0 - end transform packet + * 1 - translate along X axis (TX) + * 2 - translate along Y axis (TY) + * 3 - translate along Z axis (TZ) + * 4 - rotate about X axis (RX) + * 5 - rotate about Y axis (RY) + * 6 - rotate about Z axis (RZ) + * 7 - negate all axes (NEG) + */ + +enum link_types { + end_x_form, + tx, + ty, + tz, + rx, + ry, + rz, + neg +}; + +/* TRANSFORM */ +/* Structure used to describe a transform. */ +struct intern_transform { + struct { + u32 link_type; + s32 link_amount; + } link[8]; +}; + +/* JR3 force/torque sensor data definition. For more information see sensor + * and hardware manuals. + */ + +struct jr3_channel { + /* Raw_channels is the area used to store the raw data coming from */ + /* the sensor. */ + + struct raw_channel raw_channels[16]; /* offset 0x0000 */ + + /* Copyright is a null terminated ASCII string containing the JR3 */ + /* copyright notice. */ + + u32 copyright[0x0018]; /* offset 0x0040 */ + s32 reserved1[0x0008]; /* offset 0x0058 */ + + /* Shunts contains the sensor shunt readings. Some JR3 sensors have + * the ability to have their gains adjusted. This allows the + * hardware full scales to be adjusted to potentially allow + * better resolution or dynamic range. For sensors that have + * this ability, the gain of each sensor channel is measured at + * the time of calibration using a shunt resistor. The shunt + * resistor is placed across one arm of the resistor bridge, and + * the resulting change in the output of that channel is + * measured. This measurement is called the shunt reading, and + * is recorded here. If the user has changed the gain of the // + * sensor, and made new shunt measurements, those shunt + * measurements can be placed here. The JR3 DSP will then scale + * the calibration matrix such so that the gains are again + * proper for the indicated shunt readings. If shunts is 0, then + * the sensor cannot have its gain changed. For details on + * changing the sensor gain, and making shunts readings, please + * see the sensor manual. To make these values take effect the + * user must call either command (5) use transform # (pg. 33) or + * command (10) set new full scales (pg. 38). + */ + + struct six_axis_array shunts; /* offset 0x0060 */ + s32 reserved2[2]; /* offset 0x0066 */ + + /* Default_FS contains the full scale that is used if the user does */ + /* not set a full scale. */ + + struct six_axis_array default_FS; /* offset 0x0068 */ + s32 reserved3; /* offset 0x006e */ + + /* Load_envelope_num is the load envelope number that is currently + * in use. This value is set by the user after one of the load + * envelopes has been initialized. + */ + + s32 load_envelope_num; /* offset 0x006f */ + + /* Min_full_scale is the recommend minimum full scale. */ + + /* These values in conjunction with max_full_scale (pg. 9) helps + * determine the appropriate value for setting the full scales. The + * software allows the user to set the sensor full scale to an + * arbitrary value. But setting the full scales has some hazards. If + * the full scale is set too low, the data will saturate + * prematurely, and dynamic range will be lost. If the full scale is + * set too high, then resolution is lost as the data is shifted to + * the right and the least significant bits are lost. Therefore the + * maximum full scale is the maximum value at which no resolution is + * lost, and the minimum full scale is the value at which the data + * will not saturate prematurely. These values are calculated + * whenever a new coordinate transformation is calculated. It is + * possible for the recommended maximum to be less than the + * recommended minimum. This comes about primarily when using + * coordinate translations. If this is the case, it means that any + * full scale selection will be a compromise between dynamic range + * and resolution. It is usually recommended to compromise in favor + * of resolution which means that the recommend maximum full scale + * should be chosen. + * + * WARNING: Be sure that the full scale is no less than 0.4% of the + * recommended minimum full scale. Full scales below this value will + * cause erroneous results. + */ + + struct six_axis_array min_full_scale; /* offset 0x0070 */ + s32 reserved4; /* offset 0x0076 */ + + /* Transform_num is the transform number that is currently in use. + * This value is set by the JR3 DSP after the user has used command + * (5) use transform # (pg. 33). + */ + + s32 transform_num; /* offset 0x0077 */ + + /* Max_full_scale is the recommended maximum full scale. See */ + /* min_full_scale (pg. 9) for more details. */ + + struct six_axis_array max_full_scale; /* offset 0x0078 */ + s32 reserved5; /* offset 0x007e */ + + /* Peak_address is the address of the data which will be monitored + * by the peak routine. This value is set by the user. The peak + * routine will monitor any 8 contiguous addresses for peak values. + * (ex. to watch filter3 data for peaks, set this value to 0x00a8). + */ + + s32 peak_address; /* offset 0x007f */ + + /* Full_scale is the sensor full scales which are currently in use. + * Decoupled and filtered data is scaled so that +/- 16384 is equal + * to the full scales. The engineering units used are indicated by + * the units value discussed on page 16. The full scales for Fx, Fy, + * Fz, Mx, My and Mz can be written by the user prior to calling + * command (10) set new full scales (pg. 38). The full scales for V1 + * and V2 are set whenever the full scales are changed or when the + * axes used to calculate the vectors are changed. The full scale of + * V1 and V2 will always be equal to the largest full scale of the + * axes used for each vector respectively. + */ + + struct force_array full_scale; /* offset 0x0080 */ + + /* Offsets contains the sensor offsets. These values are subtracted from + * the sensor data to obtain the decoupled data. The offsets are set a + * few seconds (< 10) after the calibration data has been received. + * They are set so that the output data will be zero. These values + * can be written as well as read. The JR3 DSP will use the values + * written here within 2 ms of being written. To set future + * decoupled data to zero, add these values to the current decoupled + * data values and place the sum here. The JR3 DSP will change these + * values when a new transform is applied. So if the offsets are + * such that FX is 5 and all other values are zero, after rotating + * about Z by 90 degrees, FY would be 5 and all others would be zero. + */ + + struct six_axis_array offsets; /* offset 0x0088 */ + + /* Offset_num is the number of the offset currently in use. This + * value is set by the JR3 DSP after the user has executed the use + * offset # command (pg. 34). It can vary between 0 and 15. + */ + + s32 offset_num; /* offset 0x008e */ + + /* Vect_axes is a bit map showing which of the axes are being used + * in the vector calculations. This value is set by the JR3 DSP + * after the user has executed the set vector axes command (pg. 37). + */ + + u32 vect_axes; /* offset 0x008f */ + + /* Filter0 is the decoupled, unfiltered data from the JR3 sensor. + * This data has had the offsets removed. + * + * These force_arrays hold the filtered data. The decoupled data is + * passed through cascaded low pass filters. Each succeeding filter + * has a cutoff frequency of 1/4 of the preceding filter. The cutoff + * frequency of filter1 is 1/16 of the sample rate from the sensor. + * For a typical sensor with a sample rate of 8 kHz, the cutoff + * frequency of filter1 would be 500 Hz. The following filters would + * cutoff at 125 Hz, 31.25 Hz, 7.813 Hz, 1.953 Hz and 0.4883 Hz. + */ + + struct force_array filter[7]; /* offset 0x0090, + offset 0x0098, + offset 0x00a0, + offset 0x00a8, + offset 0x00b0, + offset 0x00b8 , + offset 0x00c0 */ + + /* Rate_data is the calculated rate data. It is a first derivative + * calculation. It is calculated at a frequency specified by the + * variable rate_divisor (pg. 12). The data on which the rate is + * calculated is specified by the variable rate_address (pg. 12). + */ + + struct force_array rate_data; /* offset 0x00c8 */ + + /* Minimum_data & maximum_data are the minimum and maximum (peak) + * data values. The JR3 DSP can monitor any 8 contiguous data items + * for minimums and maximums at full sensor bandwidth. This area is + * only updated at user request. This is done so that the user does + * not miss any peaks. To read the data, use either the read peaks + * command (pg. 40), or the read and reset peaks command (pg. 39). + * The address of the data to watch for peaks is stored in the + * variable peak_address (pg. 10). Peak data is lost when executing + * a coordinate transformation or a full scale change. Peak data is + * also lost when plugging in a new sensor. + */ + + struct force_array minimum_data; /* offset 0x00d0 */ + struct force_array maximum_data; /* offset 0x00d8 */ + + /* Near_sat_value & sat_value contain the value used to determine if + * the raw sensor is saturated. Because of decoupling and offset + * removal, it is difficult to tell from the processed data if the + * sensor is saturated. These values, in conjunction with the error + * and warning words (pg. 14), provide this critical information. + * These two values may be set by the host processor. These values + * are positive signed values, since the saturation logic uses the + * absolute values of the raw data. The near_sat_value defaults to + * approximately 80% of the ADC's full scale, which is 26214, while + * sat_value defaults to the ADC's full scale: + * + * sat_value = 32768 - 2^(16 - ADC bits) + */ + + s32 near_sat_value; /* offset 0x00e0 */ + s32 sat_value; /* offset 0x00e1 */ + + /* Rate_address, rate_divisor & rate_count contain the data used to + * control the calculations of the rates. Rate_address is the + * address of the data used for the rate calculation. The JR3 DSP + * will calculate rates for any 8 contiguous values (ex. to + * calculate rates for filter3 data set rate_address to 0x00a8). + * Rate_divisor is how often the rate is calculated. If rate_divisor + * is 1, the rates are calculated at full sensor bandwidth. If + * rate_divisor is 200, rates are calculated every 200 samples. + * Rate_divisor can be any value between 1 and 65536. Set + * rate_divisor to 0 to calculate rates every 65536 samples. + * Rate_count starts at zero and counts until it equals + * rate_divisor, at which point the rates are calculated, and + * rate_count is reset to 0. When setting a new rate divisor, it is + * a good idea to set rate_count to one less than rate divisor. This + * will minimize the time necessary to start the rate calculations. + */ + + s32 rate_address; /* offset 0x00e2 */ + u32 rate_divisor; /* offset 0x00e3 */ + u32 rate_count; /* offset 0x00e4 */ + + /* Command_word2 through command_word0 are the locations used to + * send commands to the JR3 DSP. Their usage varies with the command + * and is detailed later in the Command Definitions section (pg. + * 29). In general the user places values into various memory + * locations, and then places the command word into command_word0. + * The JR3 DSP will process the command and place a 0 into + * command_word0 to indicate successful completion. Alternatively + * the JR3 DSP will place a negative number into command_word0 to + * indicate an error condition. Please note the command locations + * are numbered backwards. (I.E. command_word2 comes before + * command_word1). + */ + + s32 command_word2; /* offset 0x00e5 */ + s32 command_word1; /* offset 0x00e6 */ + s32 command_word0; /* offset 0x00e7 */ + + /* Count1 through count6 are unsigned counters which are incremented + * every time the matching filters are calculated. Filter1 is + * calculated at the sensor data bandwidth. So this counter would + * increment at 8 kHz for a typical sensor. The rest of the counters + * are incremented at 1/4 the interval of the counter immediately + * preceding it, so they would count at 2 kHz, 500 Hz, 125 Hz etc. + * These counters can be used to wait for data. Each time the + * counter changes, the corresponding data set can be sampled, and + * this will insure that the user gets each sample, once, and only + * once. + */ + + u32 count1; /* offset 0x00e8 */ + u32 count2; /* offset 0x00e9 */ + u32 count3; /* offset 0x00ea */ + u32 count4; /* offset 0x00eb */ + u32 count5; /* offset 0x00ec */ + u32 count6; /* offset 0x00ed */ + + /* Error_count is a running count of data reception errors. If this + * counter is changing rapidly, it probably indicates a bad sensor + * cable connection or other hardware problem. In most installations + * error_count should not change at all. But it is possible in an + * extremely noisy environment to experience occasional errors even + * without a hardware problem. If the sensor is well grounded, this + * is probably unavoidable in these environments. On the occasions + * where this counter counts a bad sample, that sample is ignored. + */ + + u32 error_count; /* offset 0x00ee */ + + /* Count_x is a counter which is incremented every time the JR3 DSP + * searches its job queues and finds nothing to do. It indicates the + * amount of idle time the JR3 DSP has available. It can also be + * used to determine if the JR3 DSP is alive. See the Performance + * Issues section on pg. 49 for more details. + */ + + u32 count_x; /* offset 0x00ef */ + + /* Warnings & errors contain the warning and error bits + * respectively. The format of these two words is discussed on page + * 21 under the headings warnings_bits and error_bits. + */ + + u32 warnings; /* offset 0x00f0 */ + u32 errors; /* offset 0x00f1 */ + + /* Threshold_bits is a word containing the bits that are set by the + * load envelopes. See load_envelopes (pg. 17) and thresh_struct + * (pg. 23) for more details. + */ + + s32 threshold_bits; /* offset 0x00f2 */ + + /* Last_crc is the value that shows the actual calculated CRC. CRC + * is short for cyclic redundancy code. It should be zero. See the + * description for cal_crc_bad (pg. 21) for more information. + */ + + s32 last_CRC; /* offset 0x00f3 */ + + /* EEProm_ver_no contains the version number of the sensor EEProm. + * EEProm version numbers can vary between 0 and 255. + * Software_ver_no contains the software version number. Version + * 3.02 would be stored as 302. + */ + + s32 eeprom_ver_no; /* offset 0x00f4 */ + s32 software_ver_no; /* offset 0x00f5 */ + + /* Software_day & software_year are the release date of the software + * the JR3 DSP is currently running. Day is the day of the year, + * with January 1 being 1, and December 31, being 365 for non leap + * years. + */ + + s32 software_day; /* offset 0x00f6 */ + s32 software_year; /* offset 0x00f7 */ + + /* Serial_no & model_no are the two values which uniquely identify a + * sensor. This model number does not directly correspond to the JR3 + * model number, but it will provide a unique identifier for + * different sensor configurations. + */ + + u32 serial_no; /* offset 0x00f8 */ + u32 model_no; /* offset 0x00f9 */ + + /* Cal_day & cal_year are the sensor calibration date. Day is the + * day of the year, with January 1 being 1, and December 31, being + * 366 for leap years. + */ + + s32 cal_day; /* offset 0x00fa */ + s32 cal_year; /* offset 0x00fb */ + + /* Units is an enumerated read only value defining the engineering + * units used in the sensor full scale. The meanings of particular + * values are discussed in the section detailing the force_units + * structure on page 22. The engineering units are setto customer + * specifications during sensor manufacture and cannot be changed by + * writing to Units. + * + * Bits contains the number of bits of resolution of the ADC + * currently in use. + * + * Channels is a bit field showing which channels the current sensor + * is capable of sending. If bit 0 is active, this sensor can send + * channel 0, if bit 13 is active, this sensor can send channel 13, + * etc. This bit can be active, even if the sensor is not currently + * sending this channel. Some sensors are configurable as to which + * channels to send, and this field only contains information on the + * channels available to send, not on the current configuration. To + * find which channels are currently being sent, monitor the + * Raw_time fields (pg. 19) in the raw_channels array (pg. 7). If + * the time is changing periodically, then that channel is being + * received. + */ + + u32 units; /* offset 0x00fc */ + s32 bits; /* offset 0x00fd */ + s32 channels; /* offset 0x00fe */ + + /* Thickness specifies the overall thickness of the sensor from + * flange to flange. The engineering units for this value are + * contained in units (pg. 16). The sensor calibration is relative + * to the center of the sensor. This value allows easy coordinate + * transformation from the center of the sensor to either flange. + */ + + s32 thickness; /* offset 0x00ff */ + + /* Load_envelopes is a table containing the load envelope + * descriptions. There are 16 possible load envelope slots in the + * table. The slots are on 16 word boundaries and are numbered 0-15. + * Each load envelope needs to start at the beginning of a slot but + * need not be fully contained in that slot. That is to say that a + * single load envelope can be larger than a single slot. The + * software has been tested and ran satisfactorily with 50 + * thresholds active. A single load envelope this large would take + * up 5 of the 16 slots. The load envelope data is laid out in an + * order that is most efficient for the JR3 DSP. The structure is + * detailed later in the section showing the definition of the + * le_struct structure (pg. 23). + */ + + struct le_struct load_envelopes[0x10]; /* offset 0x0100 */ + + /* Transforms is a table containing the transform descriptions. + * There are 16 possible transform slots in the table. The slots are + * on 16 word boundaries and are numbered 0-15. Each transform needs + * to start at the beginning of a slot but need not be fully + * contained in that slot. That is to say that a single transform + * can be larger than a single slot. A transform is 2 * no of links + * + 1 words in length. So a single slot can contain a transform + * with 7 links. Two slots can contain a transform that is 15 links. + * The layout is detailed later in the section showing the + * definition of the transform structure (pg. 26). + */ + + struct intern_transform transforms[0x10]; /* offset 0x0200 */ +}; + +struct jr3_t { + struct { + u32 program_lo[0x4000]; /* 0x00000 - 0x10000 */ + struct jr3_channel data; /* 0x10000 - 0x10c00 */ + char pad2[0x30000 - 0x00c00]; /* 0x10c00 - 0x40000 */ + u32 program_hi[0x8000]; /* 0x40000 - 0x60000 */ + u32 reset; /* 0x60000 - 0x60004 */ + char pad3[0x20000 - 0x00004]; /* 0x60004 - 0x80000 */ + } channel[4]; +}; |