These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 446 insertions, 8 deletions

diff --git a/kernel/drivers/iio/temperature/mlx90614.c b/kernel/drivers/iio/temperature/mlx90614.c
index a112fc9ab..a570c2e2a 100644
--- a/kernel/drivers/iio/temperature/mlx90614.c
+++ b/kernel/drivers/iio/temperature/mlx90614.c
@@ -3,6 +3,7 @@
  *
  * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net>
  * Copyright (c) 2015 Essensium NV
+ * Copyright (c) 2015 Melexis
  *
  * This file is subject to the terms and conditions of version 2 of
  * the GNU General Public License.  See the file COPYING in the main
@@ -12,14 +13,26 @@
  *
  * (7-bit I2C slave address 0x5a, 100KHz bus speed only!)
  *
- * TODO: sleep mode, configuration EEPROM
+ * To wake up from sleep mode, the SDA line must be held low while SCL is high
+ * for at least 33ms.  This is achieved with an extra GPIO that can be connected
+ * directly to the SDA line.  In normal operation, the GPIO is set as input and
+ * will not interfere in I2C communication.  While the GPIO is driven low, the
+ * i2c adapter is locked since it cannot be used by other clients.  The SCL line
+ * always has a pull-up so we do not need an extra GPIO to drive it high.  If
+ * the "wakeup" GPIO is not given, power management will be disabled.
+ *
  */
 
 #include <linux/err.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/jiffies.h>
+#include <linux/gpio/consumer.h>
+#include <linux/pm_runtime.h>
 
 #include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
 
 #define MLX90614_OP_RAM		0x00
 #define MLX90614_OP_EEPROM	0x20
@@ -51,10 +64,160 @@
 #define MLX90614_TIMING_WAKEUP 34 /* time to hold SDA low for wake-up */
 #define MLX90614_TIMING_STARTUP 250 /* time before first data after wake-up */
 
+#define MLX90614_AUTOSLEEP_DELAY 5000 /* default autosleep delay */
+
+/* Magic constants */
+#define MLX90614_CONST_OFFSET_DEC -13657 /* decimal part of the Kelvin offset */
+#define MLX90614_CONST_OFFSET_REM 500000 /* remainder of offset (273.15*50) */
+#define MLX90614_CONST_SCALE 20 /* Scale in milliKelvin (0.02 * 1000) */
+#define MLX90614_CONST_RAW_EMISSIVITY_MAX 65535 /* max value for emissivity */
+#define MLX90614_CONST_EMISSIVITY_RESOLUTION 15259 /* 1/65535 ~ 0.000015259 */
+#define MLX90614_CONST_FIR 0x7 /* Fixed value for FIR part of low pass filter */
+
 struct mlx90614_data {
 	struct i2c_client *client;
+	struct mutex lock; /* for EEPROM access only */
+	struct gpio_desc *wakeup_gpio; /* NULL to disable sleep/wake-up */
+	unsigned long ready_timestamp; /* in jiffies */
+};
+
+/* Bandwidth values for IIR filtering */
+static const int mlx90614_iir_values[] = {77, 31, 20, 15, 723, 153, 110, 86};
+static IIO_CONST_ATTR(in_temp_object_filter_low_pass_3db_frequency_available,
+		      "0.15 0.20 0.31 0.77 0.86 1.10 1.53 7.23");
+
+static struct attribute *mlx90614_attributes[] = {
+	&iio_const_attr_in_temp_object_filter_low_pass_3db_frequency_available.dev_attr.attr,
+	NULL,
 };
 
+static const struct attribute_group mlx90614_attr_group = {
+	.attrs = mlx90614_attributes,
+};
+
+/*
+ * Erase an address and write word.
+ * The mutex must be locked before calling.
+ */
+static s32 mlx90614_write_word(const struct i2c_client *client, u8 command,
+			       u16 value)
+{
+	/*
+	 * Note: The mlx90614 requires a PEC on writing but does not send us a
+	 * valid PEC on reading.  Hence, we cannot set I2C_CLIENT_PEC in
+	 * i2c_client.flags.  As a workaround, we use i2c_smbus_xfer here.
+	 */
+	union i2c_smbus_data data;
+	s32 ret;
+
+	dev_dbg(&client->dev, "Writing 0x%x to address 0x%x", value, command);
+
+	data.word = 0x0000; /* erase command */
+	ret = i2c_smbus_xfer(client->adapter, client->addr,
+			     client->flags | I2C_CLIENT_PEC,
+			     I2C_SMBUS_WRITE, command,
+			     I2C_SMBUS_WORD_DATA, &data);
+	if (ret < 0)
+		return ret;
+
+	msleep(MLX90614_TIMING_EEPROM);
+
+	data.word = value; /* actual write */
+	ret = i2c_smbus_xfer(client->adapter, client->addr,
+			     client->flags | I2C_CLIENT_PEC,
+			     I2C_SMBUS_WRITE, command,
+			     I2C_SMBUS_WORD_DATA, &data);
+
+	msleep(MLX90614_TIMING_EEPROM);
+
+	return ret;
+}
+
+/*
+ * Find the IIR value inside mlx90614_iir_values array and return its position
+ * which is equivalent to the bit value in sensor register
+ */
+static inline s32 mlx90614_iir_search(const struct i2c_client *client,
+				      int value)
+{
+	int i;
+	s32 ret;
+
+	for (i = 0; i < ARRAY_SIZE(mlx90614_iir_values); ++i) {
+		if (value == mlx90614_iir_values[i])
+			break;
+	}
+
+	if (i == ARRAY_SIZE(mlx90614_iir_values))
+		return -EINVAL;
+
+	/*
+	 * CONFIG register values must not be changed so
+	 * we must read them before we actually write
+	 * changes
+	 */
+	ret = i2c_smbus_read_word_data(client, MLX90614_CONFIG);
+	if (ret < 0)
+		return ret;
+
+	ret &= ~MLX90614_CONFIG_FIR_MASK;
+	ret |= MLX90614_CONST_FIR << MLX90614_CONFIG_FIR_SHIFT;
+	ret &= ~MLX90614_CONFIG_IIR_MASK;
+	ret |= i << MLX90614_CONFIG_IIR_SHIFT;
+
+	/* Write changed values */
+	ret = mlx90614_write_word(client, MLX90614_CONFIG, ret);
+	return ret;
+}
+
+#ifdef CONFIG_PM
+/*
+ * If @startup is true, make sure MLX90614_TIMING_STARTUP ms have elapsed since
+ * the last wake-up.  This is normally only needed to get a valid temperature
+ * reading.  EEPROM access does not need such delay.
+ * Return 0 on success, <0 on error.
+ */
+static int mlx90614_power_get(struct mlx90614_data *data, bool startup)
+{
+	unsigned long now;
+
+	if (!data->wakeup_gpio)
+		return 0;
+
+	pm_runtime_get_sync(&data->client->dev);
+
+	if (startup) {
+		now = jiffies;
+		if (time_before(now, data->ready_timestamp) &&
+		    msleep_interruptible(jiffies_to_msecs(
+				data->ready_timestamp - now)) != 0) {
+			pm_runtime_put_autosuspend(&data->client->dev);
+			return -EINTR;
+		}
+	}
+
+	return 0;
+}
+
+static void mlx90614_power_put(struct mlx90614_data *data)
+{
+	if (!data->wakeup_gpio)
+		return;
+
+	pm_runtime_mark_last_busy(&data->client->dev);
+	pm_runtime_put_autosuspend(&data->client->dev);
+}
+#else
+static inline int mlx90614_power_get(struct mlx90614_data *data, bool startup)
+{
+	return 0;
+}
+
+static inline void mlx90614_power_put(struct mlx90614_data *data)
+{
+}
+#endif
+
 static int mlx90614_read_raw(struct iio_dev *indio_dev,
 			    struct iio_chan_spec const *channel, int *val,
 			    int *val2, long mask)
@@ -85,18 +248,115 @@ static int mlx90614_read_raw(struct iio_dev *indio_dev,
 			return -EINVAL;
 		}
 
+		ret = mlx90614_power_get(data, true);
+		if (ret < 0)
+			return ret;
 		ret = i2c_smbus_read_word_data(data->client, cmd);
+		mlx90614_power_put(data);
+
 		if (ret < 0)
 			return ret;
+
+		/* MSB is an error flag */
+		if (ret & 0x8000)
+			return -EIO;
+
 		*val = ret;
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_OFFSET:
-		*val = 13657;
-		*val2 = 500000;
+		*val = MLX90614_CONST_OFFSET_DEC;
+		*val2 = MLX90614_CONST_OFFSET_REM;
 		return IIO_VAL_INT_PLUS_MICRO;
 	case IIO_CHAN_INFO_SCALE:
-		*val = 20;
+		*val = MLX90614_CONST_SCALE;
 		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_CALIBEMISSIVITY: /* 1/65535 / LSB */
+		mlx90614_power_get(data, false);
+		mutex_lock(&data->lock);
+		ret = i2c_smbus_read_word_data(data->client,
+					       MLX90614_EMISSIVITY);
+		mutex_unlock(&data->lock);
+		mlx90614_power_put(data);
+
+		if (ret < 0)
+			return ret;
+
+		if (ret == MLX90614_CONST_RAW_EMISSIVITY_MAX) {
+			*val = 1;
+			*val2 = 0;
+		} else {
+			*val = 0;
+			*val2 = ret * MLX90614_CONST_EMISSIVITY_RESOLUTION;
+		}
+		return IIO_VAL_INT_PLUS_NANO;
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* IIR setting with
+							     FIR = 1024 */
+		mlx90614_power_get(data, false);
+		mutex_lock(&data->lock);
+		ret = i2c_smbus_read_word_data(data->client, MLX90614_CONFIG);
+		mutex_unlock(&data->lock);
+		mlx90614_power_put(data);
+
+		if (ret < 0)
+			return ret;
+
+		*val = mlx90614_iir_values[ret & MLX90614_CONFIG_IIR_MASK] / 100;
+		*val2 = (mlx90614_iir_values[ret & MLX90614_CONFIG_IIR_MASK] % 100) *
+			10000;
+		return IIO_VAL_INT_PLUS_MICRO;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mlx90614_write_raw(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *channel, int val,
+			     int val2, long mask)
+{
+	struct mlx90614_data *data = iio_priv(indio_dev);
+	s32 ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_CALIBEMISSIVITY: /* 1/65535 / LSB */
+		if (val < 0 || val2 < 0 || val > 1 || (val == 1 && val2 != 0))
+			return -EINVAL;
+		val = val * MLX90614_CONST_RAW_EMISSIVITY_MAX +
+			val2 / MLX90614_CONST_EMISSIVITY_RESOLUTION;
+
+		mlx90614_power_get(data, false);
+		mutex_lock(&data->lock);
+		ret = mlx90614_write_word(data->client, MLX90614_EMISSIVITY,
+					  val);
+		mutex_unlock(&data->lock);
+		mlx90614_power_put(data);
+
+		return ret;
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* IIR Filter setting */
+		if (val < 0 || val2 < 0)
+			return -EINVAL;
+
+		mlx90614_power_get(data, false);
+		mutex_lock(&data->lock);
+		ret = mlx90614_iir_search(data->client,
+					  val * 100 + val2 / 10000);
+		mutex_unlock(&data->lock);
+		mlx90614_power_put(data);
+
+		return ret;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int mlx90614_write_raw_get_fmt(struct iio_dev *indio_dev,
+				     struct iio_chan_spec const *channel,
+				     long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_CALIBEMISSIVITY:
+		return IIO_VAL_INT_PLUS_NANO;
+	case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+		return IIO_VAL_INT_PLUS_MICRO;
 	default:
 		return -EINVAL;
 	}
@@ -115,7 +375,9 @@ static const struct iio_chan_spec mlx90614_channels[] = {
 		.type = IIO_TEMP,
 		.modified = 1,
 		.channel2 = IIO_MOD_TEMP_OBJECT,
-		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		    BIT(IIO_CHAN_INFO_CALIBEMISSIVITY) |
+			BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) |
 		    BIT(IIO_CHAN_INFO_SCALE),
 	},
@@ -125,7 +387,9 @@ static const struct iio_chan_spec mlx90614_channels[] = {
 		.modified = 1,
 		.channel = 1,
 		.channel2 = IIO_MOD_TEMP_OBJECT,
-		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		    BIT(IIO_CHAN_INFO_CALIBEMISSIVITY) |
+			BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) |
 		    BIT(IIO_CHAN_INFO_SCALE),
 	},
@@ -133,9 +397,104 @@ static const struct iio_chan_spec mlx90614_channels[] = {
 
 static const struct iio_info mlx90614_info = {
 	.read_raw = mlx90614_read_raw,
+	.write_raw = mlx90614_write_raw,
+	.write_raw_get_fmt = mlx90614_write_raw_get_fmt,
+	.attrs = &mlx90614_attr_group,
 	.driver_module = THIS_MODULE,
 };
 
+#ifdef CONFIG_PM
+static int mlx90614_sleep(struct mlx90614_data *data)
+{
+	s32 ret;
+
+	if (!data->wakeup_gpio) {
+		dev_dbg(&data->client->dev, "Sleep disabled");
+		return -ENOSYS;
+	}
+
+	dev_dbg(&data->client->dev, "Requesting sleep");
+
+	mutex_lock(&data->lock);
+	ret = i2c_smbus_xfer(data->client->adapter, data->client->addr,
+			     data->client->flags | I2C_CLIENT_PEC,
+			     I2C_SMBUS_WRITE, MLX90614_OP_SLEEP,
+			     I2C_SMBUS_BYTE, NULL);
+	mutex_unlock(&data->lock);
+
+	return ret;
+}
+
+static int mlx90614_wakeup(struct mlx90614_data *data)
+{
+	if (!data->wakeup_gpio) {
+		dev_dbg(&data->client->dev, "Wake-up disabled");
+		return -ENOSYS;
+	}
+
+	dev_dbg(&data->client->dev, "Requesting wake-up");
+
+	i2c_lock_adapter(data->client->adapter);
+	gpiod_direction_output(data->wakeup_gpio, 0);
+	msleep(MLX90614_TIMING_WAKEUP);
+	gpiod_direction_input(data->wakeup_gpio);
+	i2c_unlock_adapter(data->client->adapter);
+
+	data->ready_timestamp = jiffies +
+			msecs_to_jiffies(MLX90614_TIMING_STARTUP);
+
+	/*
+	 * Quirk: the i2c controller may get confused right after the
+	 * wake-up signal has been sent.  As a workaround, do a dummy read.
+	 * If the read fails, the controller will probably be reset so that
+	 * further reads will work.
+	 */
+	i2c_smbus_read_word_data(data->client, MLX90614_CONFIG);
+
+	return 0;
+}
+
+/* Return wake-up GPIO or NULL if sleep functionality should be disabled. */
+static struct gpio_desc *mlx90614_probe_wakeup(struct i2c_client *client)
+{
+	struct gpio_desc *gpio;
+
+	if (!i2c_check_functionality(client->adapter,
+						I2C_FUNC_SMBUS_WRITE_BYTE)) {
+		dev_info(&client->dev,
+			 "i2c adapter does not support SMBUS_WRITE_BYTE, sleep disabled");
+		return NULL;
+	}
+
+	gpio = devm_gpiod_get_optional(&client->dev, "wakeup", GPIOD_IN);
+
+	if (IS_ERR(gpio)) {
+		dev_warn(&client->dev,
+			 "gpio acquisition failed with error %ld, sleep disabled",
+			 PTR_ERR(gpio));
+		return NULL;
+	} else if (!gpio) {
+		dev_info(&client->dev,
+			 "wakeup-gpio not found, sleep disabled");
+	}
+
+	return gpio;
+}
+#else
+static inline int mlx90614_sleep(struct mlx90614_data *data)
+{
+	return -ENOSYS;
+}
+static inline int mlx90614_wakeup(struct mlx90614_data *data)
+{
+	return -ENOSYS;
+}
+static inline struct gpio_desc *mlx90614_probe_wakeup(struct i2c_client *client)
+{
+	return NULL;
+}
+#endif
+
 /* Return 0 for single sensor, 1 for dual sensor, <0 on error. */
 static int mlx90614_probe_num_ir_sensors(struct i2c_client *client)
 {
@@ -166,6 +525,10 @@ static int mlx90614_probe(struct i2c_client *client,
 	data = iio_priv(indio_dev);
 	i2c_set_clientdata(client, indio_dev);
 	data->client = client;
+	mutex_init(&data->lock);
+	data->wakeup_gpio = mlx90614_probe_wakeup(client);
+
+	mlx90614_wakeup(data);
 
 	indio_dev->dev.parent = &client->dev;
 	indio_dev->name = id->name;
@@ -188,12 +551,30 @@ static int mlx90614_probe(struct i2c_client *client,
 		return ret;
 	}
 
+	if (data->wakeup_gpio) {
+		pm_runtime_set_autosuspend_delay(&client->dev,
+						 MLX90614_AUTOSLEEP_DELAY);
+		pm_runtime_use_autosuspend(&client->dev);
+		pm_runtime_set_active(&client->dev);
+		pm_runtime_enable(&client->dev);
+	}
+
 	return iio_device_register(indio_dev);
 }
 
 static int mlx90614_remove(struct i2c_client *client)
 {
-	iio_device_unregister(i2c_get_clientdata(client));
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+	struct mlx90614_data *data = iio_priv(indio_dev);
+
+	iio_device_unregister(indio_dev);
+
+	if (data->wakeup_gpio) {
+		pm_runtime_disable(&client->dev);
+		if (!pm_runtime_status_suspended(&client->dev))
+			mlx90614_sleep(data);
+		pm_runtime_set_suspended(&client->dev);
+	}
 
 	return 0;
 }
@@ -204,10 +585,66 @@ static const struct i2c_device_id mlx90614_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, mlx90614_id);
 
+#ifdef CONFIG_PM_SLEEP
+static int mlx90614_pm_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+	struct mlx90614_data *data = iio_priv(indio_dev);
+
+	if (data->wakeup_gpio && pm_runtime_active(dev))
+		return mlx90614_sleep(data);
+
+	return 0;
+}
+
+static int mlx90614_pm_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+	struct mlx90614_data *data = iio_priv(indio_dev);
+	int err;
+
+	if (data->wakeup_gpio) {
+		err = mlx90614_wakeup(data);
+		if (err < 0)
+			return err;
+
+		pm_runtime_disable(dev);
+		pm_runtime_set_active(dev);
+		pm_runtime_enable(dev);
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_PM
+static int mlx90614_pm_runtime_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+	struct mlx90614_data *data = iio_priv(indio_dev);
+
+	return mlx90614_sleep(data);
+}
+
+static int mlx90614_pm_runtime_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+	struct mlx90614_data *data = iio_priv(indio_dev);
+
+	return mlx90614_wakeup(data);
+}
+#endif
+
+static const struct dev_pm_ops mlx90614_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mlx90614_pm_suspend, mlx90614_pm_resume)
+	SET_RUNTIME_PM_OPS(mlx90614_pm_runtime_suspend,
+			   mlx90614_pm_runtime_resume, NULL)
+};
+
 static struct i2c_driver mlx90614_driver = {
 	.driver = {
 		.name	= "mlx90614",
-		.owner	= THIS_MODULE,
+		.pm	= &mlx90614_pm_ops,
 	},
 	.probe = mlx90614_probe,
 	.remove = mlx90614_remove,
@@ -217,5 +654,6 @@ module_i2c_driver(mlx90614_driver);
 
 MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>");
 MODULE_AUTHOR("Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>");
+MODULE_AUTHOR("Crt Mori <cmo@melexis.com>");
 MODULE_DESCRIPTION("Melexis MLX90614 contactless IR temperature sensor driver");
 MODULE_LICENSE("GPL");