Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 1548 insertions, 0 deletions

diff --git a/kernel/drivers/ide/hpt366.c b/kernel/drivers/ide/hpt366.c
new file mode 100644
index 000000000..0d0a96629
--- /dev/null
+++ b/kernel/drivers/ide/hpt366.c
@@ -0,0 +1,1548 @@
+/*
+ * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003		Red Hat Inc
+ * Portions Copyright (C) 2007		Bartlomiej Zolnierkiewicz
+ * Portions Copyright (C) 2005-2009	MontaVista Software, Inc.
+ *
+ * Thanks to HighPoint Technologies for their assistance, and hardware.
+ * Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his
+ * donation of an ABit BP6 mainboard, processor, and memory acellerated
+ * development and support.
+ *
+ *
+ * HighPoint has its own drivers (open source except for the RAID part)
+ * available from http://www.highpoint-tech.com/USA_new/service_support.htm 
+ * This may be useful to anyone wanting to work on this driver, however  do not
+ * trust  them too much since the code tends to become less and less meaningful
+ * as the time passes... :-/
+ *
+ * Note that final HPT370 support was done by force extraction of GPL.
+ *
+ * - add function for getting/setting power status of drive
+ * - the HPT370's state machine can get confused. reset it before each dma 
+ *   xfer to prevent that from happening.
+ * - reset state engine whenever we get an error.
+ * - check for busmaster state at end of dma. 
+ * - use new highpoint timings.
+ * - detect bus speed using highpoint register.
+ * - use pll if we don't have a clock table. added a 66MHz table that's
+ *   just 2x the 33MHz table.
+ * - removed turnaround. NOTE: we never want to switch between pll and
+ *   pci clocks as the chip can glitch in those cases. the highpoint
+ *   approved workaround slows everything down too much to be useful. in
+ *   addition, we would have to serialize access to each chip.
+ * 	Adrian Sun <a.sun@sun.com>
+ *
+ * add drive timings for 66MHz PCI bus,
+ * fix ATA Cable signal detection, fix incorrect /proc info
+ * add /proc display for per-drive PIO/DMA/UDMA mode and
+ * per-channel ATA-33/66 Cable detect.
+ * 	Duncan Laurie <void@sun.com>
+ *
+ * fixup /proc output for multiple controllers
+ *	Tim Hockin <thockin@sun.com>
+ *
+ * On hpt366: 
+ * Reset the hpt366 on error, reset on dma
+ * Fix disabling Fast Interrupt hpt366.
+ * 	Mike Waychison <crlf@sun.com>
+ *
+ * Added support for 372N clocking and clock switching. The 372N needs
+ * different clocks on read/write. This requires overloading rw_disk and
+ * other deeply crazy things. Thanks to <http://www.hoerstreich.de> for
+ * keeping me sane. 
+ *		Alan Cox <alan@lxorguk.ukuu.org.uk>
+ *
+ * - fix the clock turnaround code: it was writing to the wrong ports when
+ *   called for the secondary channel, caching the current clock mode per-
+ *   channel caused the cached register value to get out of sync with the
+ *   actual one, the channels weren't serialized, the turnaround shouldn't
+ *   be done on 66 MHz PCI bus
+ * - disable UltraATA/100 for HPT370 by default as the 33 MHz clock being used
+ *   does not allow for this speed anyway
+ * - avoid touching disabled channels (e.g. HPT371/N are single channel chips,
+ *   their primary channel is kind of virtual, it isn't tied to any pins)
+ * - fix/remove bad/unused timing tables and use one set of tables for the whole
+ *   HPT37x chip family; save space by introducing the separate transfer mode
+ *   table in which the mode lookup is done
+ * - use f_CNT value saved by  the HighPoint BIOS as reading it directly gives
+ *   the wrong PCI frequency since DPLL has already been calibrated by BIOS;
+ *   read it only from the function 0 of HPT374 chips
+ * - fix the hotswap code:  it caused RESET- to glitch when tristating the bus,
+ *   and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead
+ * - pass to init_chipset() handlers a copy of the IDE PCI device structure as
+ *   they tamper with its fields
+ * - pass  to the init_setup handlers a copy of the ide_pci_device_t structure
+ *   since they may tamper with its fields
+ * - prefix the driver startup messages with the real chip name
+ * - claim the extra 240 bytes of I/O space for all chips
+ * - optimize the UltraDMA filtering and the drive list lookup code
+ * - use pci_get_slot() to get to the function 1 of HPT36x/374
+ * - cache offset of the channel's misc. control registers (MCRs) being used
+ *   throughout the driver
+ * - only touch the relevant MCR when detecting the cable type on HPT374's
+ *   function 1
+ * - rename all the register related variables consistently
+ * - move all the interrupt twiddling code from the speedproc handlers into
+ *   init_hwif_hpt366(), also grouping all the DMA related code together there
+ * - merge HPT36x/HPT37x speedproc handlers, fix PIO timing register mask and
+ *   separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
+ *   when setting an UltraDMA mode
+ * - fix hpt3xx_tune_drive() to set the PIO mode requested, not always select
+ *   the best possible one
+ * - clean up DMA timeout handling for HPT370
+ * - switch to using the enumeration type to differ between the numerous chip
+ *   variants, matching PCI device/revision ID with the chip type early, at the
+ *   init_setup stage
+ * - extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
+ *   stop duplicating it for each channel by storing the pointer in the pci_dev
+ *   structure: first, at the init_setup stage, point it to a static "template"
+ *   with only the chip type and its specific base DPLL frequency, the highest
+ *   UltraDMA mode, and the chip settings table pointer filled,  then, at the
+ *   init_chipset stage, allocate per-chip instance  and fill it with the rest
+ *   of the necessary information
+ * - get rid of the constant thresholds in the HPT37x PCI clock detection code,
+ *   switch  to calculating  PCI clock frequency based on the chip's base DPLL
+ *   frequency
+ * - switch to using the  DPLL clock and enable UltraATA/133 mode by default on
+ *   anything  newer than HPT370/A (except HPT374 that is not capable of this
+ *   mode according to the manual)
+ * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
+ *   also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips;
+ *   unify HPT36x/37x timing setup code and the speedproc handlers by joining
+ *   the register setting lists into the table indexed by the clock selected
+ * - set the correct hwif->ultra_mask for each individual chip
+ * - add Ultra and MW DMA mode filtering for the HPT37[24] based SATA cards
+ * - stop resetting HPT370's state machine before each DMA transfer as that has
+ *   caused more harm than good
+ *	Sergei Shtylyov, <sshtylyov@ru.mvista.com> or <source@mvista.com>
+ */
+
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/blkdev.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/ide.h>
+#include <linux/slab.h>
+
+#include <asm/uaccess.h>
+#include <asm/io.h>
+
+#define DRV_NAME "hpt366"
+
+/* various tuning parameters */
+#undef	HPT_RESET_STATE_ENGINE
+#undef	HPT_DELAY_INTERRUPT
+
+static const char *bad_ata100_5[] = {
+	"IBM-DTLA-307075",
+	"IBM-DTLA-307060",
+	"IBM-DTLA-307045",
+	"IBM-DTLA-307030",
+	"IBM-DTLA-307020",
+	"IBM-DTLA-307015",
+	"IBM-DTLA-305040",
+	"IBM-DTLA-305030",
+	"IBM-DTLA-305020",
+	"IC35L010AVER07-0",
+	"IC35L020AVER07-0",
+	"IC35L030AVER07-0",
+	"IC35L040AVER07-0",
+	"IC35L060AVER07-0",
+	"WDC AC310200R",
+	NULL
+};
+
+static const char *bad_ata66_4[] = {
+	"IBM-DTLA-307075",
+	"IBM-DTLA-307060",
+	"IBM-DTLA-307045",
+	"IBM-DTLA-307030",
+	"IBM-DTLA-307020",
+	"IBM-DTLA-307015",
+	"IBM-DTLA-305040",
+	"IBM-DTLA-305030",
+	"IBM-DTLA-305020",
+	"IC35L010AVER07-0",
+	"IC35L020AVER07-0",
+	"IC35L030AVER07-0",
+	"IC35L040AVER07-0",
+	"IC35L060AVER07-0",
+	"WDC AC310200R",
+	"MAXTOR STM3320620A",
+	NULL
+};
+
+static const char *bad_ata66_3[] = {
+	"WDC AC310200R",
+	NULL
+};
+
+static const char *bad_ata33[] = {
+	"Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
+	"Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
+	"Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
+	"Maxtor 90510D4",
+	"Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
+	"Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
+	"Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
+	NULL
+};
+
+static u8 xfer_speeds[] = {
+	XFER_UDMA_6,
+	XFER_UDMA_5,
+	XFER_UDMA_4,
+	XFER_UDMA_3,
+	XFER_UDMA_2,
+	XFER_UDMA_1,
+	XFER_UDMA_0,
+
+	XFER_MW_DMA_2,
+	XFER_MW_DMA_1,
+	XFER_MW_DMA_0,
+
+	XFER_PIO_4,
+	XFER_PIO_3,
+	XFER_PIO_2,
+	XFER_PIO_1,
+	XFER_PIO_0
+};
+
+/* Key for bus clock timings
+ * 36x   37x
+ * bits  bits
+ * 0:3	 0:3	data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ *		cycles = value + 1
+ * 4:7	 4:8	data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ *		cycles = value + 1
+ * 8:11  9:12	cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
+ *		register access.
+ * 12:15 13:17	cmd_low_time. Active time of DIOW_/DIOR_ during task file
+ *		register access.
+ * 16:18 18:20	udma_cycle_time. Clock cycles for UDMA xfer.
+ * -	 21	CLK frequency: 0=ATA clock, 1=dual ATA clock.
+ * 19:21 22:24	pre_high_time. Time to initialize the 1st cycle for PIO and
+ *		MW DMA xfer.
+ * 22:24 25:27	cmd_pre_high_time. Time to initialize the 1st PIO cycle for
+ *		task file register access.
+ * 28	 28	UDMA enable.
+ * 29	 29	DMA  enable.
+ * 30	 30	PIO MST enable. If set, the chip is in bus master mode during
+ *		PIO xfer.
+ * 31	 31	FIFO enable.
+ */
+
+static u32 forty_base_hpt36x[] = {
+	/* XFER_UDMA_6 */	0x900fd943,
+	/* XFER_UDMA_5 */	0x900fd943,
+	/* XFER_UDMA_4 */	0x900fd943,
+	/* XFER_UDMA_3 */	0x900ad943,
+	/* XFER_UDMA_2 */	0x900bd943,
+	/* XFER_UDMA_1 */	0x9008d943,
+	/* XFER_UDMA_0 */	0x9008d943,
+
+	/* XFER_MW_DMA_2 */	0xa008d943,
+	/* XFER_MW_DMA_1 */	0xa010d955,
+	/* XFER_MW_DMA_0 */	0xa010d9fc,
+
+	/* XFER_PIO_4 */	0xc008d963,
+	/* XFER_PIO_3 */	0xc010d974,
+	/* XFER_PIO_2 */	0xc010d997,
+	/* XFER_PIO_1 */	0xc010d9c7,
+	/* XFER_PIO_0 */	0xc018d9d9
+};
+
+static u32 thirty_three_base_hpt36x[] = {
+	/* XFER_UDMA_6 */	0x90c9a731,
+	/* XFER_UDMA_5 */	0x90c9a731,
+	/* XFER_UDMA_4 */	0x90c9a731,
+	/* XFER_UDMA_3 */	0x90cfa731,
+	/* XFER_UDMA_2 */	0x90caa731,
+	/* XFER_UDMA_1 */	0x90cba731,
+	/* XFER_UDMA_0 */	0x90c8a731,
+
+	/* XFER_MW_DMA_2 */	0xa0c8a731,
+	/* XFER_MW_DMA_1 */	0xa0c8a732,	/* 0xa0c8a733 */
+	/* XFER_MW_DMA_0 */	0xa0c8a797,
+
+	/* XFER_PIO_4 */	0xc0c8a731,
+	/* XFER_PIO_3 */	0xc0c8a742,
+	/* XFER_PIO_2 */	0xc0d0a753,
+	/* XFER_PIO_1 */	0xc0d0a7a3,	/* 0xc0d0a793 */
+	/* XFER_PIO_0 */	0xc0d0a7aa	/* 0xc0d0a7a7 */
+};
+
+static u32 twenty_five_base_hpt36x[] = {
+	/* XFER_UDMA_6 */	0x90c98521,
+	/* XFER_UDMA_5 */	0x90c98521,
+	/* XFER_UDMA_4 */	0x90c98521,
+	/* XFER_UDMA_3 */	0x90cf8521,
+	/* XFER_UDMA_2 */	0x90cf8521,
+	/* XFER_UDMA_1 */	0x90cb8521,
+	/* XFER_UDMA_0 */	0x90cb8521,
+
+	/* XFER_MW_DMA_2 */	0xa0ca8521,
+	/* XFER_MW_DMA_1 */	0xa0ca8532,
+	/* XFER_MW_DMA_0 */	0xa0ca8575,
+
+	/* XFER_PIO_4 */	0xc0ca8521,
+	/* XFER_PIO_3 */	0xc0ca8532,
+	/* XFER_PIO_2 */	0xc0ca8542,
+	/* XFER_PIO_1 */	0xc0d08572,
+	/* XFER_PIO_0 */	0xc0d08585
+};
+
+/*
+ * The following are the new timing tables with PIO mode data/taskfile transfer
+ * overclocking fixed...
+ */
+
+/* This table is taken from the HPT370 data manual rev. 1.02 */
+static u32 thirty_three_base_hpt37x[] = {
+	/* XFER_UDMA_6 */	0x16455031,	/* 0x16655031 ?? */
+	/* XFER_UDMA_5 */	0x16455031,
+	/* XFER_UDMA_4 */	0x16455031,
+	/* XFER_UDMA_3 */	0x166d5031,
+	/* XFER_UDMA_2 */	0x16495031,
+	/* XFER_UDMA_1 */	0x164d5033,
+	/* XFER_UDMA_0 */	0x16515097,
+
+	/* XFER_MW_DMA_2 */	0x26515031,
+	/* XFER_MW_DMA_1 */	0x26515033,
+	/* XFER_MW_DMA_0 */	0x26515097,
+
+	/* XFER_PIO_4 */	0x06515021,
+	/* XFER_PIO_3 */	0x06515022,
+	/* XFER_PIO_2 */	0x06515033,
+	/* XFER_PIO_1 */	0x06915065,
+	/* XFER_PIO_0 */	0x06d1508a
+};
+
+static u32 fifty_base_hpt37x[] = {
+	/* XFER_UDMA_6 */	0x1a861842,
+	/* XFER_UDMA_5 */	0x1a861842,
+	/* XFER_UDMA_4 */	0x1aae1842,
+	/* XFER_UDMA_3 */	0x1a8e1842,
+	/* XFER_UDMA_2 */	0x1a0e1842,
+	/* XFER_UDMA_1 */	0x1a161854,
+	/* XFER_UDMA_0 */	0x1a1a18ea,
+
+	/* XFER_MW_DMA_2 */	0x2a821842,
+	/* XFER_MW_DMA_1 */	0x2a821854,
+	/* XFER_MW_DMA_0 */	0x2a8218ea,
+
+	/* XFER_PIO_4 */	0x0a821842,
+	/* XFER_PIO_3 */	0x0a821843,
+	/* XFER_PIO_2 */	0x0a821855,
+	/* XFER_PIO_1 */	0x0ac218a8,
+	/* XFER_PIO_0 */	0x0b02190c
+};
+
+static u32 sixty_six_base_hpt37x[] = {
+	/* XFER_UDMA_6 */	0x1c86fe62,
+	/* XFER_UDMA_5 */	0x1caefe62,	/* 0x1c8afe62 */
+	/* XFER_UDMA_4 */	0x1c8afe62,
+	/* XFER_UDMA_3 */	0x1c8efe62,
+	/* XFER_UDMA_2 */	0x1c92fe62,
+	/* XFER_UDMA_1 */	0x1c9afe62,
+	/* XFER_UDMA_0 */	0x1c82fe62,
+
+	/* XFER_MW_DMA_2 */	0x2c82fe62,
+	/* XFER_MW_DMA_1 */	0x2c82fe66,
+	/* XFER_MW_DMA_0 */	0x2c82ff2e,
+
+	/* XFER_PIO_4 */	0x0c82fe62,
+	/* XFER_PIO_3 */	0x0c82fe84,
+	/* XFER_PIO_2 */	0x0c82fea6,
+	/* XFER_PIO_1 */	0x0d02ff26,
+	/* XFER_PIO_0 */	0x0d42ff7f
+};
+
+#define HPT371_ALLOW_ATA133_6		1
+#define HPT302_ALLOW_ATA133_6		1
+#define HPT372_ALLOW_ATA133_6		1
+#define HPT370_ALLOW_ATA100_5		0
+#define HPT366_ALLOW_ATA66_4		1
+#define HPT366_ALLOW_ATA66_3		1
+
+/* Supported ATA clock frequencies */
+enum ata_clock {
+	ATA_CLOCK_25MHZ,
+	ATA_CLOCK_33MHZ,
+	ATA_CLOCK_40MHZ,
+	ATA_CLOCK_50MHZ,
+	ATA_CLOCK_66MHZ,
+	NUM_ATA_CLOCKS
+};
+
+struct hpt_timings {
+	u32 pio_mask;
+	u32 dma_mask;
+	u32 ultra_mask;
+	u32 *clock_table[NUM_ATA_CLOCKS];
+};
+
+/*
+ *	Hold all the HighPoint chip information in one place.
+ */
+
+struct hpt_info {
+	char *chip_name;	/* Chip name */
+	u8 chip_type;		/* Chip type */
+	u8 udma_mask;		/* Allowed UltraDMA modes mask. */
+	u8 dpll_clk;		/* DPLL clock in MHz */
+	u8 pci_clk;		/* PCI  clock in MHz */
+	struct hpt_timings *timings; /* Chipset timing data */
+	u8 clock;		/* ATA clock selected */
+};
+
+/* Supported HighPoint chips */
+enum {
+	HPT36x,
+	HPT370,
+	HPT370A,
+	HPT374,
+	HPT372,
+	HPT372A,
+	HPT302,
+	HPT371,
+	HPT372N,
+	HPT302N,
+	HPT371N
+};
+
+static struct hpt_timings hpt36x_timings = {
+	.pio_mask	= 0xc1f8ffff,
+	.dma_mask	= 0x303800ff,
+	.ultra_mask	= 0x30070000,
+	.clock_table	= {
+		[ATA_CLOCK_25MHZ] = twenty_five_base_hpt36x,
+		[ATA_CLOCK_33MHZ] = thirty_three_base_hpt36x,
+		[ATA_CLOCK_40MHZ] = forty_base_hpt36x,
+		[ATA_CLOCK_50MHZ] = NULL,
+		[ATA_CLOCK_66MHZ] = NULL
+	}
+};
+
+static struct hpt_timings hpt37x_timings = {
+	.pio_mask	= 0xcfc3ffff,
+	.dma_mask	= 0x31c001ff,
+	.ultra_mask	= 0x303c0000,
+	.clock_table	= {
+		[ATA_CLOCK_25MHZ] = NULL,
+		[ATA_CLOCK_33MHZ] = thirty_three_base_hpt37x,
+		[ATA_CLOCK_40MHZ] = NULL,
+		[ATA_CLOCK_50MHZ] = fifty_base_hpt37x,
+		[ATA_CLOCK_66MHZ] = sixty_six_base_hpt37x
+	}
+};
+
+static const struct hpt_info hpt36x = {
+	.chip_name	= "HPT36x",
+	.chip_type	= HPT36x,
+	.udma_mask	= HPT366_ALLOW_ATA66_3 ? (HPT366_ALLOW_ATA66_4 ? ATA_UDMA4 : ATA_UDMA3) : ATA_UDMA2,
+	.dpll_clk	= 0,	/* no DPLL */
+	.timings	= &hpt36x_timings
+};
+
+static const struct hpt_info hpt370 = {
+	.chip_name	= "HPT370",
+	.chip_type	= HPT370,
+	.udma_mask	= HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4,
+	.dpll_clk	= 48,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt370a = {
+	.chip_name	= "HPT370A",
+	.chip_type	= HPT370A,
+	.udma_mask	= HPT370_ALLOW_ATA100_5 ? ATA_UDMA5 : ATA_UDMA4,
+	.dpll_clk	= 48,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt374 = {
+	.chip_name	= "HPT374",
+	.chip_type	= HPT374,
+	.udma_mask	= ATA_UDMA5,
+	.dpll_clk	= 48,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt372 = {
+	.chip_name	= "HPT372",
+	.chip_type	= HPT372,
+	.udma_mask	= HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 55,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt372a = {
+	.chip_name	= "HPT372A",
+	.chip_type	= HPT372A,
+	.udma_mask	= HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 66,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt302 = {
+	.chip_name	= "HPT302",
+	.chip_type	= HPT302,
+	.udma_mask	= HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 66,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt371 = {
+	.chip_name	= "HPT371",
+	.chip_type	= HPT371,
+	.udma_mask	= HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 66,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt372n = {
+	.chip_name	= "HPT372N",
+	.chip_type	= HPT372N,
+	.udma_mask	= HPT372_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 77,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt302n = {
+	.chip_name	= "HPT302N",
+	.chip_type	= HPT302N,
+	.udma_mask	= HPT302_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 77,
+	.timings	= &hpt37x_timings
+};
+
+static const struct hpt_info hpt371n = {
+	.chip_name	= "HPT371N",
+	.chip_type	= HPT371N,
+	.udma_mask	= HPT371_ALLOW_ATA133_6 ? ATA_UDMA6 : ATA_UDMA5,
+	.dpll_clk	= 77,
+	.timings	= &hpt37x_timings
+};
+
+static int check_in_drive_list(ide_drive_t *drive, const char **list)
+{
+	char *m = (char *)&drive->id[ATA_ID_PROD];
+
+	while (*list)
+		if (!strcmp(*list++, m))
+			return 1;
+	return 0;
+}
+
+static struct hpt_info *hpt3xx_get_info(struct device *dev)
+{
+	struct ide_host *host	= dev_get_drvdata(dev);
+	struct hpt_info *info	= (struct hpt_info *)host->host_priv;
+
+	return dev == host->dev[1] ? info + 1 : info;
+}
+
+/*
+ * The Marvell bridge chips used on the HighPoint SATA cards do not seem
+ * to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
+ */
+
+static u8 hpt3xx_udma_filter(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
+	u8 mask 		= hwif->ultra_mask;
+
+	switch (info->chip_type) {
+	case HPT36x:
+		if (!HPT366_ALLOW_ATA66_4 ||
+		    check_in_drive_list(drive, bad_ata66_4))
+			mask = ATA_UDMA3;
+
+		if (!HPT366_ALLOW_ATA66_3 ||
+		    check_in_drive_list(drive, bad_ata66_3))
+			mask = ATA_UDMA2;
+		break;
+	case HPT370:
+		if (!HPT370_ALLOW_ATA100_5 ||
+		    check_in_drive_list(drive, bad_ata100_5))
+			mask = ATA_UDMA4;
+		break;
+	case HPT370A:
+		if (!HPT370_ALLOW_ATA100_5 ||
+		    check_in_drive_list(drive, bad_ata100_5))
+			return ATA_UDMA4;
+	case HPT372 :
+	case HPT372A:
+	case HPT372N:
+	case HPT374 :
+		if (ata_id_is_sata(drive->id))
+			mask &= ~0x0e;
+		/* Fall thru */
+	default:
+		return mask;
+	}
+
+	return check_in_drive_list(drive, bad_ata33) ? 0x00 : mask;
+}
+
+static u8 hpt3xx_mdma_filter(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
+
+	switch (info->chip_type) {
+	case HPT372 :
+	case HPT372A:
+	case HPT372N:
+	case HPT374 :
+		if (ata_id_is_sata(drive->id))
+			return 0x00;
+		/* Fall thru */
+	default:
+		return 0x07;
+	}
+}
+
+static u32 get_speed_setting(u8 speed, struct hpt_info *info)
+{
+	int i;
+
+	/*
+	 * Lookup the transfer mode table to get the index into
+	 * the timing table.
+	 *
+	 * NOTE: For XFER_PIO_SLOW, PIO mode 0 timings will be used.
+	 */
+	for (i = 0; i < ARRAY_SIZE(xfer_speeds) - 1; i++)
+		if (xfer_speeds[i] == speed)
+			break;
+
+	return info->timings->clock_table[info->clock][i];
+}
+
+static void hpt3xx_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
+	struct hpt_timings *t	= info->timings;
+	u8  itr_addr		= 0x40 + (drive->dn * 4);
+	u32 old_itr		= 0;
+	const u8 speed		= drive->dma_mode;
+	u32 new_itr		= get_speed_setting(speed, info);
+	u32 itr_mask		= speed < XFER_MW_DMA_0 ? t->pio_mask :
+				 (speed < XFER_UDMA_0   ? t->dma_mask :
+							  t->ultra_mask);
+
+	pci_read_config_dword(dev, itr_addr, &old_itr);
+	new_itr = (old_itr & ~itr_mask) | (new_itr & itr_mask);
+	/*
+	 * Disable on-chip PIO FIFO/buffer (and PIO MST mode as well)
+	 * to avoid problems handling I/O errors later
+	 */
+	new_itr &= ~0xc0000000;
+
+	pci_write_config_dword(dev, itr_addr, new_itr);
+}
+
+static void hpt3xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+	drive->dma_mode = drive->pio_mode;
+	hpt3xx_set_mode(hwif, drive);
+}
+
+static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev	*dev	= to_pci_dev(hwif->dev);
+	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
+
+	if ((drive->dev_flags & IDE_DFLAG_NIEN_QUIRK) == 0)
+		return;
+
+	if (info->chip_type >= HPT370) {
+		u8 scr1 = 0;
+
+		pci_read_config_byte(dev, 0x5a, &scr1);
+		if (((scr1 & 0x10) >> 4) != mask) {
+			if (mask)
+				scr1 |=  0x10;
+			else
+				scr1 &= ~0x10;
+			pci_write_config_byte(dev, 0x5a, scr1);
+		}
+	} else if (mask)
+		disable_irq(hwif->irq);
+	else
+		enable_irq(hwif->irq);
+}
+
+/*
+ * This is specific to the HPT366 UDMA chipset
+ * by HighPoint|Triones Technologies, Inc.
+ */
+static void hpt366_dma_lost_irq(ide_drive_t *drive)
+{
+	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+	u8 mcr1 = 0, mcr3 = 0, scr1 = 0;
+
+	pci_read_config_byte(dev, 0x50, &mcr1);
+	pci_read_config_byte(dev, 0x52, &mcr3);
+	pci_read_config_byte(dev, 0x5a, &scr1);
+	printk("%s: (%s)  mcr1=0x%02x, mcr3=0x%02x, scr1=0x%02x\n",
+		drive->name, __func__, mcr1, mcr3, scr1);
+	if (scr1 & 0x10)
+		pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
+	ide_dma_lost_irq(drive);
+}
+
+static void hpt370_clear_engine(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+
+	pci_write_config_byte(dev, hwif->select_data, 0x37);
+	udelay(10);
+}
+
+static void hpt370_irq_timeout(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	u16 bfifo		= 0;
+	u8  dma_cmd;
+
+	pci_read_config_word(dev, hwif->select_data + 2, &bfifo);
+	printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo & 0x1ff);
+
+	/* get DMA command mode */
+	dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
+	/* stop DMA */
+	outb(dma_cmd & ~ATA_DMA_START, hwif->dma_base + ATA_DMA_CMD);
+	hpt370_clear_engine(drive);
+}
+
+static void hpt370_dma_start(ide_drive_t *drive)
+{
+#ifdef HPT_RESET_STATE_ENGINE
+	hpt370_clear_engine(drive);
+#endif
+	ide_dma_start(drive);
+}
+
+static int hpt370_dma_end(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	u8  dma_stat		= inb(hwif->dma_base + ATA_DMA_STATUS);
+
+	if (dma_stat & ATA_DMA_ACTIVE) {
+		/* wait a little */
+		udelay(20);
+		dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
+		if (dma_stat & ATA_DMA_ACTIVE)
+			hpt370_irq_timeout(drive);
+	}
+	return ide_dma_end(drive);
+}
+
+/* returns 1 if DMA IRQ issued, 0 otherwise */
+static int hpt374_dma_test_irq(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	u16 bfifo		= 0;
+	u8  dma_stat;
+
+	pci_read_config_word(dev, hwif->select_data + 2, &bfifo);
+	if (bfifo & 0x1FF) {
+//		printk("%s: %d bytes in FIFO\n", drive->name, bfifo);
+		return 0;
+	}
+
+	dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
+	/* return 1 if INTR asserted */
+	if (dma_stat & ATA_DMA_INTR)
+		return 1;
+
+	return 0;
+}
+
+static int hpt374_dma_end(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif	= drive->hwif;
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	u8 mcr	= 0, mcr_addr	= hwif->select_data;
+	u8 bwsr = 0, mask	= hwif->channel ? 0x02 : 0x01;
+
+	pci_read_config_byte(dev, 0x6a, &bwsr);
+	pci_read_config_byte(dev, mcr_addr, &mcr);
+	if (bwsr & mask)
+		pci_write_config_byte(dev, mcr_addr, mcr | 0x30);
+	return ide_dma_end(drive);
+}
+
+/**
+ *	hpt3xxn_set_clock	-	perform clock switching dance
+ *	@hwif: hwif to switch
+ *	@mode: clocking mode (0x21 for write, 0x23 otherwise)
+ *
+ *	Switch the DPLL clock on the HPT3xxN devices. This is a	right mess.
+ */
+
+static void hpt3xxn_set_clock(ide_hwif_t *hwif, u8 mode)
+{
+	unsigned long base = hwif->extra_base;
+	u8 scr2 = inb(base + 0x6b);
+
+	if ((scr2 & 0x7f) == mode)
+		return;
+
+	/* Tristate the bus */
+	outb(0x80, base + 0x63);
+	outb(0x80, base + 0x67);
+
+	/* Switch clock and reset channels */
+	outb(mode, base + 0x6b);
+	outb(0xc0, base + 0x69);
+
+	/*
+	 * Reset the state machines.
+	 * NOTE: avoid accidentally enabling the disabled channels.
+	 */
+	outb(inb(base + 0x60) | 0x32, base + 0x60);
+	outb(inb(base + 0x64) | 0x32, base + 0x64);
+
+	/* Complete reset */
+	outb(0x00, base + 0x69);
+
+	/* Reconnect channels to bus */
+	outb(0x00, base + 0x63);
+	outb(0x00, base + 0x67);
+}
+
+/**
+ *	hpt3xxn_rw_disk		-	prepare for I/O
+ *	@drive: drive for command
+ *	@rq: block request structure
+ *
+ *	This is called when a disk I/O is issued to HPT3xxN.
+ *	We need it because of the clock switching.
+ */
+
+static void hpt3xxn_rw_disk(ide_drive_t *drive, struct request *rq)
+{
+	hpt3xxn_set_clock(drive->hwif, rq_data_dir(rq) ? 0x21 : 0x23);
+}
+
+/**
+ *	hpt37x_calibrate_dpll	-	calibrate the DPLL
+ *	@dev: PCI device
+ *
+ *	Perform a calibration cycle on the DPLL.
+ *	Returns 1 if this succeeds
+ */
+static int hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f_high)
+{
+	u32 dpll = (f_high << 16) | f_low | 0x100;
+	u8  scr2;
+	int i;
+
+	pci_write_config_dword(dev, 0x5c, dpll);
+
+	/* Wait for oscillator ready */
+	for(i = 0; i < 0x5000; ++i) {
+		udelay(50);
+		pci_read_config_byte(dev, 0x5b, &scr2);
+		if (scr2 & 0x80)
+			break;
+	}
+	/* See if it stays ready (we'll just bail out if it's not yet) */
+	for(i = 0; i < 0x1000; ++i) {
+		pci_read_config_byte(dev, 0x5b, &scr2);
+		/* DPLL destabilized? */
+		if(!(scr2 & 0x80))
+			return 0;
+	}
+	/* Turn off tuning, we have the DPLL set */
+	pci_read_config_dword (dev, 0x5c, &dpll);
+	pci_write_config_dword(dev, 0x5c, (dpll & ~0x100));
+	return 1;
+}
+
+static void hpt3xx_disable_fast_irq(struct pci_dev *dev, u8 mcr_addr)
+{
+	struct ide_host *host	= pci_get_drvdata(dev);
+	struct hpt_info *info	= host->host_priv + (&dev->dev == host->dev[1]);
+	u8  chip_type		= info->chip_type;
+	u8  new_mcr, old_mcr	= 0;
+
+	/*
+	 * Disable the "fast interrupt" prediction.  Don't hold off
+	 * on interrupts. (== 0x01 despite what the docs say)
+	 */
+	pci_read_config_byte(dev, mcr_addr + 1, &old_mcr);
+
+	if (chip_type >= HPT374)
+		new_mcr = old_mcr & ~0x07;
+	else if (chip_type >= HPT370) {
+		new_mcr = old_mcr;
+		new_mcr &= ~0x02;
+#ifdef HPT_DELAY_INTERRUPT
+		new_mcr &= ~0x01;
+#else
+		new_mcr |=  0x01;
+#endif
+	} else					/* HPT366 and HPT368  */
+		new_mcr = old_mcr & ~0x80;
+
+	if (new_mcr != old_mcr)
+		pci_write_config_byte(dev, mcr_addr + 1, new_mcr);
+}
+
+static int init_chipset_hpt366(struct pci_dev *dev)
+{
+	unsigned long io_base	= pci_resource_start(dev, 4);
+	struct hpt_info *info	= hpt3xx_get_info(&dev->dev);
+	const char *name	= DRV_NAME;
+	u8 pci_clk,  dpll_clk	= 0;	/* PCI and DPLL clock in MHz */
+	u8 chip_type;
+	enum ata_clock	clock;
+
+	chip_type = info->chip_type;
+
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+	/*
+	 * First, try to estimate the PCI clock frequency...
+	 */
+	if (chip_type >= HPT370) {
+		u8  scr1  = 0;
+		u16 f_cnt = 0;
+		u32 temp  = 0;
+
+		/* Interrupt force enable. */
+		pci_read_config_byte(dev, 0x5a, &scr1);
+		if (scr1 & 0x10)
+			pci_write_config_byte(dev, 0x5a, scr1 & ~0x10);
+
+		/*
+		 * HighPoint does this for HPT372A.
+		 * NOTE: This register is only writeable via I/O space.
+		 */
+		if (chip_type == HPT372A)
+			outb(0x0e, io_base + 0x9c);
+
+		/*
+		 * Default to PCI clock. Make sure MA15/16 are set to output
+		 * to prevent drives having problems with 40-pin cables.
+		 */
+		pci_write_config_byte(dev, 0x5b, 0x23);
+
+		/*
+		 * We'll have to read f_CNT value in order to determine
+		 * the PCI clock frequency according to the following ratio:
+		 *
+		 * f_CNT = Fpci * 192 / Fdpll
+		 *
+		 * First try reading the register in which the HighPoint BIOS
+		 * saves f_CNT value before  reprogramming the DPLL from its
+		 * default setting (which differs for the various chips).
+		 *
+		 * NOTE: This register is only accessible via I/O space;
+		 * HPT374 BIOS only saves it for the function 0, so we have to
+		 * always read it from there -- no need to check the result of
+		 * pci_get_slot() for the function 0 as the whole device has
+		 * been already "pinned" (via function 1) in init_setup_hpt374()
+		 */
+		if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
+			struct pci_dev	*dev1 = pci_get_slot(dev->bus,
+							     dev->devfn - 1);
+			unsigned long io_base = pci_resource_start(dev1, 4);
+
+			temp =	inl(io_base + 0x90);
+			pci_dev_put(dev1);
+		} else
+			temp =	inl(io_base + 0x90);
+
+		/*
+		 * In case the signature check fails, we'll have to
+		 * resort to reading the f_CNT register itself in hopes
+		 * that nobody has touched the DPLL yet...
+		 */
+		if ((temp & 0xFFFFF000) != 0xABCDE000) {
+			int i;
+
+			printk(KERN_WARNING "%s %s: no clock data saved by "
+				"BIOS\n", name, pci_name(dev));
+
+			/* Calculate the average value of f_CNT. */
+			for (temp = i = 0; i < 128; i++) {
+				pci_read_config_word(dev, 0x78, &f_cnt);
+				temp += f_cnt & 0x1ff;
+				mdelay(1);
+			}
+			f_cnt = temp / 128;
+		} else
+			f_cnt = temp & 0x1ff;
+
+		dpll_clk = info->dpll_clk;
+		pci_clk  = (f_cnt * dpll_clk) / 192;
+
+		/* Clamp PCI clock to bands. */
+		if (pci_clk < 40)
+			pci_clk = 33;
+		else if(pci_clk < 45)
+			pci_clk = 40;
+		else if(pci_clk < 55)
+			pci_clk = 50;
+		else
+			pci_clk = 66;
+
+		printk(KERN_INFO "%s %s: DPLL base: %d MHz, f_CNT: %d, "
+			"assuming %d MHz PCI\n", name, pci_name(dev),
+			dpll_clk, f_cnt, pci_clk);
+	} else {
+		u32 itr1 = 0;
+
+		pci_read_config_dword(dev, 0x40, &itr1);
+
+		/* Detect PCI clock by looking at cmd_high_time. */
+		switch((itr1 >> 8) & 0x07) {
+			case 0x09:
+				pci_clk = 40;
+				break;
+			case 0x05:
+				pci_clk = 25;
+				break;
+			case 0x07:
+			default:
+				pci_clk = 33;
+				break;
+		}
+	}
+
+	/* Let's assume we'll use PCI clock for the ATA clock... */
+	switch (pci_clk) {
+		case 25:
+			clock = ATA_CLOCK_25MHZ;
+			break;
+		case 33:
+		default:
+			clock = ATA_CLOCK_33MHZ;
+			break;
+		case 40:
+			clock = ATA_CLOCK_40MHZ;
+			break;
+		case 50:
+			clock = ATA_CLOCK_50MHZ;
+			break;
+		case 66:
+			clock = ATA_CLOCK_66MHZ;
+			break;
+	}
+
+	/*
+	 * Only try the DPLL if we don't have a table for the PCI clock that
+	 * we are running at for HPT370/A, always use it  for anything newer...
+	 *
+	 * NOTE: Using the internal DPLL results in slow reads on 33 MHz PCI.
+	 * We also  don't like using  the DPLL because this causes glitches
+	 * on PRST-/SRST- when the state engine gets reset...
+	 */
+	if (chip_type >= HPT374 || info->timings->clock_table[clock] == NULL) {
+		u16 f_low, delta = pci_clk < 50 ? 2 : 4;
+		int adjust;
+
+		 /*
+		  * Select 66 MHz DPLL clock only if UltraATA/133 mode is
+		  * supported/enabled, use 50 MHz DPLL clock otherwise...
+		  */
+		if (info->udma_mask == ATA_UDMA6) {
+			dpll_clk = 66;
+			clock = ATA_CLOCK_66MHZ;
+		} else if (dpll_clk) {	/* HPT36x chips don't have DPLL */
+			dpll_clk = 50;
+			clock = ATA_CLOCK_50MHZ;
+		}
+
+		if (info->timings->clock_table[clock] == NULL) {
+			printk(KERN_ERR "%s %s: unknown bus timing!\n",
+				name, pci_name(dev));
+			return -EIO;
+		}
+
+		/* Select the DPLL clock. */
+		pci_write_config_byte(dev, 0x5b, 0x21);
+
+		/*
+		 * Adjust the DPLL based upon PCI clock, enable it,
+		 * and wait for stabilization...
+		 */
+		f_low = (pci_clk * 48) / dpll_clk;
+
+		for (adjust = 0; adjust < 8; adjust++) {
+			if(hpt37x_calibrate_dpll(dev, f_low, f_low + delta))
+				break;
+
+			/*
+			 * See if it'll settle at a fractionally different clock
+			 */
+			if (adjust & 1)
+				f_low -= adjust >> 1;
+			else
+				f_low += adjust >> 1;
+		}
+		if (adjust == 8) {
+			printk(KERN_ERR "%s %s: DPLL did not stabilize!\n",
+				name, pci_name(dev));
+			return -EIO;
+		}
+
+		printk(KERN_INFO "%s %s: using %d MHz DPLL clock\n",
+			name, pci_name(dev), dpll_clk);
+	} else {
+		/* Mark the fact that we're not using the DPLL. */
+		dpll_clk = 0;
+
+		printk(KERN_INFO "%s %s: using %d MHz PCI clock\n",
+			name, pci_name(dev), pci_clk);
+	}
+
+	/* Store the clock frequencies. */
+	info->dpll_clk	= dpll_clk;
+	info->pci_clk	= pci_clk;
+	info->clock	= clock;
+
+	if (chip_type >= HPT370) {
+		u8  mcr1, mcr4;
+
+		/*
+		 * Reset the state engines.
+		 * NOTE: Avoid accidentally enabling the disabled channels.
+		 */
+		pci_read_config_byte (dev, 0x50, &mcr1);
+		pci_read_config_byte (dev, 0x54, &mcr4);
+		pci_write_config_byte(dev, 0x50, (mcr1 | 0x32));
+		pci_write_config_byte(dev, 0x54, (mcr4 | 0x32));
+		udelay(100);
+	}
+
+	/*
+	 * On  HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+	 * the MISC. register to stretch the UltraDMA Tss timing.
+	 * NOTE: This register is only writeable via I/O space.
+	 */
+	if (chip_type == HPT371N && clock == ATA_CLOCK_66MHZ)
+		outb(inb(io_base + 0x9c) | 0x04, io_base + 0x9c);
+
+	hpt3xx_disable_fast_irq(dev, 0x50);
+	hpt3xx_disable_fast_irq(dev, 0x54);
+
+	return 0;
+}
+
+static u8 hpt3xx_cable_detect(ide_hwif_t *hwif)
+{
+	struct pci_dev	*dev	= to_pci_dev(hwif->dev);
+	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
+	u8 chip_type		= info->chip_type;
+	u8 scr1 = 0, ata66	= hwif->channel ? 0x01 : 0x02;
+
+	/*
+	 * The HPT37x uses the CBLID pins as outputs for MA15/MA16
+	 * address lines to access an external EEPROM.  To read valid
+	 * cable detect state the pins must be enabled as inputs.
+	 */
+	if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) {
+		/*
+		 * HPT374 PCI function 1
+		 * - set bit 15 of reg 0x52 to enable TCBLID as input
+		 * - set bit 15 of reg 0x56 to enable FCBLID as input
+		 */
+		u8  mcr_addr = hwif->select_data + 2;
+		u16 mcr;
+
+		pci_read_config_word(dev, mcr_addr, &mcr);
+		pci_write_config_word(dev, mcr_addr, mcr | 0x8000);
+		/* Debounce, then read cable ID register */
+		udelay(10);
+		pci_read_config_byte(dev, 0x5a, &scr1);
+		pci_write_config_word(dev, mcr_addr, mcr);
+	} else if (chip_type >= HPT370) {
+		/*
+		 * HPT370/372 and 374 pcifn 0
+		 * - clear bit 0 of reg 0x5b to enable P/SCBLID as inputs
+		 */
+		u8 scr2 = 0;
+
+		pci_read_config_byte(dev, 0x5b, &scr2);
+		pci_write_config_byte(dev, 0x5b, scr2 & ~1);
+		/* Debounce, then read cable ID register */
+		udelay(10);
+		pci_read_config_byte(dev, 0x5a, &scr1);
+		pci_write_config_byte(dev, 0x5b, scr2);
+	} else
+		pci_read_config_byte(dev, 0x5a, &scr1);
+
+	return (scr1 & ata66) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
+}
+
+static void init_hwif_hpt366(ide_hwif_t *hwif)
+{
+	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
+	u8  chip_type		= info->chip_type;
+
+	/* Cache the channel's MISC. control registers' offset */
+	hwif->select_data	= hwif->channel ? 0x54 : 0x50;
+
+	/*
+	 * HPT3xxN chips have some complications:
+	 *
+	 * - on 33 MHz PCI we must clock switch
+	 * - on 66 MHz PCI we must NOT use the PCI clock
+	 */
+	if (chip_type >= HPT372N && info->dpll_clk && info->pci_clk < 66) {
+		/*
+		 * Clock is shared between the channels,
+		 * so we'll have to serialize them... :-(
+		 */
+		hwif->host->host_flags |= IDE_HFLAG_SERIALIZE;
+		hwif->rw_disk = &hpt3xxn_rw_disk;
+	}
+}
+
+static int init_dma_hpt366(ide_hwif_t *hwif,
+				     const struct ide_port_info *d)
+{
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	unsigned long flags, base = ide_pci_dma_base(hwif, d);
+	u8 dma_old, dma_new, masterdma = 0, slavedma = 0;
+
+	if (base == 0)
+		return -1;
+
+	hwif->dma_base = base;
+
+	if (ide_pci_check_simplex(hwif, d) < 0)
+		return -1;
+
+	if (ide_pci_set_master(dev, d->name) < 0)
+		return -1;
+
+	dma_old = inb(base + 2);
+
+	local_irq_save_nort(flags);
+
+	dma_new = dma_old;
+	pci_read_config_byte(dev, hwif->channel ? 0x4b : 0x43, &masterdma);
+	pci_read_config_byte(dev, hwif->channel ? 0x4f : 0x47,  &slavedma);
+
+	if (masterdma & 0x30)	dma_new |= 0x20;
+	if ( slavedma & 0x30)	dma_new |= 0x40;
+	if (dma_new != dma_old)
+		outb(dma_new, base + 2);
+
+	local_irq_restore_nort(flags);
+
+	printk(KERN_INFO "    %s: BM-DMA at 0x%04lx-0x%04lx\n",
+			 hwif->name, base, base + 7);
+
+	hwif->extra_base = base + (hwif->channel ? 8 : 16);
+
+	if (ide_allocate_dma_engine(hwif))
+		return -1;
+
+	return 0;
+}
+
+static void hpt374_init(struct pci_dev *dev, struct pci_dev *dev2)
+{
+	if (dev2->irq != dev->irq) {
+		/* FIXME: we need a core pci_set_interrupt() */
+		dev2->irq = dev->irq;
+		printk(KERN_INFO DRV_NAME " %s: PCI config space interrupt "
+			"fixed\n", pci_name(dev2));
+	}
+}
+
+static void hpt371_init(struct pci_dev *dev)
+{
+	u8 mcr1 = 0;
+
+	/*
+	 * HPT371 chips physically have only one channel, the secondary one,
+	 * but the primary channel registers do exist!  Go figure...
+	 * So,  we manually disable the non-existing channel here
+	 * (if the BIOS hasn't done this already).
+	 */
+	pci_read_config_byte(dev, 0x50, &mcr1);
+	if (mcr1 & 0x04)
+		pci_write_config_byte(dev, 0x50, mcr1 & ~0x04);
+}
+
+static int hpt36x_init(struct pci_dev *dev, struct pci_dev *dev2)
+{
+	u8 mcr1 = 0, pin1 = 0, pin2 = 0;
+
+	/*
+	 * Now we'll have to force both channels enabled if
+	 * at least one of them has been enabled by BIOS...
+	 */
+	pci_read_config_byte(dev, 0x50, &mcr1);
+	if (mcr1 & 0x30)
+		pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
+
+	pci_read_config_byte(dev,  PCI_INTERRUPT_PIN, &pin1);
+	pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2);
+
+	if (pin1 != pin2 && dev->irq == dev2->irq) {
+		printk(KERN_INFO DRV_NAME " %s: onboard version of chipset, "
+			"pin1=%d pin2=%d\n", pci_name(dev), pin1, pin2);
+		return 1;
+	}
+
+	return 0;
+}
+
+#define IDE_HFLAGS_HPT3XX \
+	(IDE_HFLAG_NO_ATAPI_DMA | \
+	 IDE_HFLAG_OFF_BOARD)
+
+static const struct ide_port_ops hpt3xx_port_ops = {
+	.set_pio_mode		= hpt3xx_set_pio_mode,
+	.set_dma_mode		= hpt3xx_set_mode,
+	.maskproc		= hpt3xx_maskproc,
+	.mdma_filter		= hpt3xx_mdma_filter,
+	.udma_filter		= hpt3xx_udma_filter,
+	.cable_detect		= hpt3xx_cable_detect,
+};
+
+static const struct ide_dma_ops hpt37x_dma_ops = {
+	.dma_host_set		= ide_dma_host_set,
+	.dma_setup		= ide_dma_setup,
+	.dma_start		= ide_dma_start,
+	.dma_end		= hpt374_dma_end,
+	.dma_test_irq		= hpt374_dma_test_irq,
+	.dma_lost_irq		= ide_dma_lost_irq,
+	.dma_timer_expiry	= ide_dma_sff_timer_expiry,
+	.dma_sff_read_status	= ide_dma_sff_read_status,
+};
+
+static const struct ide_dma_ops hpt370_dma_ops = {
+	.dma_host_set		= ide_dma_host_set,
+	.dma_setup		= ide_dma_setup,
+	.dma_start		= hpt370_dma_start,
+	.dma_end		= hpt370_dma_end,
+	.dma_test_irq		= ide_dma_test_irq,
+	.dma_lost_irq		= ide_dma_lost_irq,
+	.dma_timer_expiry	= ide_dma_sff_timer_expiry,
+	.dma_clear		= hpt370_irq_timeout,
+	.dma_sff_read_status	= ide_dma_sff_read_status,
+};
+
+static const struct ide_dma_ops hpt36x_dma_ops = {
+	.dma_host_set		= ide_dma_host_set,
+	.dma_setup		= ide_dma_setup,
+	.dma_start		= ide_dma_start,
+	.dma_end		= ide_dma_end,
+	.dma_test_irq		= ide_dma_test_irq,
+	.dma_lost_irq		= hpt366_dma_lost_irq,
+	.dma_timer_expiry	= ide_dma_sff_timer_expiry,
+	.dma_sff_read_status	= ide_dma_sff_read_status,
+};
+
+static const struct ide_port_info hpt366_chipsets[] = {
+	{	/* 0: HPT36x */
+		.name		= DRV_NAME,
+		.init_chipset	= init_chipset_hpt366,
+		.init_hwif	= init_hwif_hpt366,
+		.init_dma	= init_dma_hpt366,
+		/*
+		 * HPT36x chips have one channel per function and have
+		 * both channel enable bits located differently and visible
+		 * to both functions -- really stupid design decision... :-(
+		 * Bit 4 is for the primary channel, bit 5 for the secondary.
+		 */
+		.enablebits	= {{0x50,0x10,0x10}, {0x54,0x04,0x04}},
+		.port_ops	= &hpt3xx_port_ops,
+		.dma_ops	= &hpt36x_dma_ops,
+		.host_flags	= IDE_HFLAGS_HPT3XX | IDE_HFLAG_SINGLE,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA2,
+	},
+	{	/* 1: HPT3xx */
+		.name		= DRV_NAME,
+		.init_chipset	= init_chipset_hpt366,
+		.init_hwif	= init_hwif_hpt366,
+		.init_dma	= init_dma_hpt366,
+		.enablebits	= {{0x50,0x04,0x04}, {0x54,0x04,0x04}},
+		.port_ops	= &hpt3xx_port_ops,
+		.dma_ops	= &hpt37x_dma_ops,
+		.host_flags	= IDE_HFLAGS_HPT3XX,
+		.pio_mask	= ATA_PIO4,
+		.mwdma_mask	= ATA_MWDMA2,
+	}
+};
+
+/**
+ *	hpt366_init_one	-	called when an HPT366 is found
+ *	@dev: the hpt366 device
+ *	@id: the matching pci id
+ *
+ *	Called when the PCI registration layer (or the IDE initialization)
+ *	finds a device matching our IDE device tables.
+ */
+static int hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	const struct hpt_info *info = NULL;
+	struct hpt_info *dyn_info;
+	struct pci_dev *dev2 = NULL;
+	struct ide_port_info d;
+	u8 idx = id->driver_data;
+	u8 rev = dev->revision;
+	int ret;
+
+	if ((idx == 0 || idx == 4) && (PCI_FUNC(dev->devfn) & 1))
+		return -ENODEV;
+
+	switch (idx) {
+	case 0:
+		if (rev < 3)
+			info = &hpt36x;
+		else {
+			switch (min_t(u8, rev, 6)) {
+			case 3: info = &hpt370;  break;
+			case 4: info = &hpt370a; break;
+			case 5: info = &hpt372;  break;
+			case 6: info = &hpt372n; break;
+			}
+			idx++;
+		}
+		break;
+	case 1:
+		info = (rev > 1) ? &hpt372n : &hpt372a;
+		break;
+	case 2:
+		info = (rev > 1) ? &hpt302n : &hpt302;
+		break;
+	case 3:
+		hpt371_init(dev);
+		info = (rev > 1) ? &hpt371n : &hpt371;
+		break;
+	case 4:
+		info = &hpt374;
+		break;
+	case 5:
+		info = &hpt372n;
+		break;
+	}
+
+	printk(KERN_INFO DRV_NAME ": %s chipset detected\n", info->chip_name);
+
+	d = hpt366_chipsets[min_t(u8, idx, 1)];
+
+	d.udma_mask = info->udma_mask;
+
+	/* fixup ->dma_ops for HPT370/HPT370A */
+	if (info == &hpt370 || info == &hpt370a)
+		d.dma_ops = &hpt370_dma_ops;
+
+	if (info == &hpt36x || info == &hpt374)
+		dev2 = pci_get_slot(dev->bus, dev->devfn + 1);
+
+	dyn_info = kzalloc(sizeof(*dyn_info) * (dev2 ? 2 : 1), GFP_KERNEL);
+	if (dyn_info == NULL) {
+		printk(KERN_ERR "%s %s: out of memory!\n",
+			d.name, pci_name(dev));
+		pci_dev_put(dev2);
+		return -ENOMEM;
+	}
+
+	/*
+	 * Copy everything from a static "template" structure
+	 * to just allocated per-chip hpt_info structure.
+	 */
+	memcpy(dyn_info, info, sizeof(*dyn_info));
+
+	if (dev2) {
+		memcpy(dyn_info + 1, info, sizeof(*dyn_info));
+
+		if (info == &hpt374)
+			hpt374_init(dev, dev2);
+		else {
+			if (hpt36x_init(dev, dev2))
+				d.host_flags &= ~IDE_HFLAG_NON_BOOTABLE;
+		}
+
+		ret = ide_pci_init_two(dev, dev2, &d, dyn_info);
+		if (ret < 0) {
+			pci_dev_put(dev2);
+			kfree(dyn_info);
+		}
+		return ret;
+	}
+
+	ret = ide_pci_init_one(dev, &d, dyn_info);
+	if (ret < 0)
+		kfree(dyn_info);
+
+	return ret;
+}
+
+static void hpt366_remove(struct pci_dev *dev)
+{
+	struct ide_host *host = pci_get_drvdata(dev);
+	struct ide_info *info = host->host_priv;
+	struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL;
+
+	ide_pci_remove(dev);
+	pci_dev_put(dev2);
+	kfree(info);
+}
+
+static const struct pci_device_id hpt366_pci_tbl[] = {
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366),  0 },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372),  1 },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302),  2 },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371),  3 },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374),  4 },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), 5 },
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl);
+
+static struct pci_driver hpt366_pci_driver = {
+	.name		= "HPT366_IDE",
+	.id_table	= hpt366_pci_tbl,
+	.probe		= hpt366_init_one,
+	.remove		= hpt366_remove,
+	.suspend	= ide_pci_suspend,
+	.resume		= ide_pci_resume,
+};
+
+static int __init hpt366_ide_init(void)
+{
+	return ide_pci_register_driver(&hpt366_pci_driver);
+}
+
+static void __exit hpt366_ide_exit(void)
+{
+	pci_unregister_driver(&hpt366_pci_driver);
+}
+
+module_init(hpt366_ide_init);
+module_exit(hpt366_ide_exit);
+
+MODULE_AUTHOR("Andre Hedrick");
+MODULE_DESCRIPTION("PCI driver module for Highpoint HPT366 IDE");
+MODULE_LICENSE("GPL");