These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 712 insertions, 13 deletions

diff --git a/kernel/drivers/bluetooth/hci_bcm.c b/kernel/drivers/bluetooth/hci_bcm.c
index 1ec0b4a5f..cb852cc75 100644
--- a/kernel/drivers/bluetooth/hci_bcm.c
+++ b/kernel/drivers/bluetooth/hci_bcm.c
@@ -24,6 +24,16 @@
 #include <linux/kernel.h>
 #include <linux/errno.h>
 #include <linux/skbuff.h>
+#include <linux/firmware.h>
+#include <linux/module.h>
+#include <linux/acpi.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/gpio/consumer.h>
+#include <linux/tty.h>
+#include <linux/interrupt.h>
+#include <linux/dmi.h>
+#include <linux/pm_runtime.h>
 
 #include <net/bluetooth/bluetooth.h>
 #include <net/bluetooth/hci_core.h>
@@ -31,16 +41,243 @@
 #include "btbcm.h"
 #include "hci_uart.h"
 
+#define BCM_LM_DIAG_PKT 0x07
+#define BCM_LM_DIAG_SIZE 63
+
+#define BCM_AUTOSUSPEND_DELAY	5000 /* default autosleep delay */
+
+struct bcm_device {
+	struct list_head	list;
+
+	struct platform_device	*pdev;
+
+	const char		*name;
+	struct gpio_desc	*device_wakeup;
+	struct gpio_desc	*shutdown;
+
+	struct clk		*clk;
+	bool			clk_enabled;
+
+	u32			init_speed;
+	int			irq;
+	u8			irq_polarity;
+
+#ifdef CONFIG_PM
+	struct hci_uart		*hu;
+	bool			is_suspended; /* suspend/resume flag */
+#endif
+};
+
 struct bcm_data {
-	struct sk_buff *rx_skb;
-	struct sk_buff_head txq;
+	struct sk_buff		*rx_skb;
+	struct sk_buff_head	txq;
+
+	struct bcm_device	*dev;
 };
 
+/* List of BCM BT UART devices */
+static DEFINE_MUTEX(bcm_device_lock);
+static LIST_HEAD(bcm_device_list);
+
+static int bcm_set_baudrate(struct hci_uart *hu, unsigned int speed)
+{
+	struct hci_dev *hdev = hu->hdev;
+	struct sk_buff *skb;
+	struct bcm_update_uart_baud_rate param;
+
+	if (speed > 3000000) {
+		struct bcm_write_uart_clock_setting clock;
+
+		clock.type = BCM_UART_CLOCK_48MHZ;
+
+		bt_dev_dbg(hdev, "Set Controller clock (%d)", clock.type);
+
+		/* This Broadcom specific command changes the UART's controller
+		 * clock for baud rate > 3000000.
+		 */
+		skb = __hci_cmd_sync(hdev, 0xfc45, 1, &clock, HCI_INIT_TIMEOUT);
+		if (IS_ERR(skb)) {
+			int err = PTR_ERR(skb);
+			bt_dev_err(hdev, "BCM: failed to write clock (%d)",
+				   err);
+			return err;
+		}
+
+		kfree_skb(skb);
+	}
+
+	bt_dev_dbg(hdev, "Set Controller UART speed to %d bit/s", speed);
+
+	param.zero = cpu_to_le16(0);
+	param.baud_rate = cpu_to_le32(speed);
+
+	/* This Broadcom specific command changes the UART's controller baud
+	 * rate.
+	 */
+	skb = __hci_cmd_sync(hdev, 0xfc18, sizeof(param), &param,
+			     HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		int err = PTR_ERR(skb);
+		bt_dev_err(hdev, "BCM: failed to write update baudrate (%d)",
+			   err);
+		return err;
+	}
+
+	kfree_skb(skb);
+
+	return 0;
+}
+
+/* bcm_device_exists should be protected by bcm_device_lock */
+static bool bcm_device_exists(struct bcm_device *device)
+{
+	struct list_head *p;
+
+	list_for_each(p, &bcm_device_list) {
+		struct bcm_device *dev = list_entry(p, struct bcm_device, list);
+
+		if (device == dev)
+			return true;
+	}
+
+	return false;
+}
+
+static int bcm_gpio_set_power(struct bcm_device *dev, bool powered)
+{
+	if (powered && !IS_ERR(dev->clk) && !dev->clk_enabled)
+		clk_enable(dev->clk);
+
+	gpiod_set_value(dev->shutdown, powered);
+	gpiod_set_value(dev->device_wakeup, powered);
+
+	if (!powered && !IS_ERR(dev->clk) && dev->clk_enabled)
+		clk_disable(dev->clk);
+
+	dev->clk_enabled = powered;
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static irqreturn_t bcm_host_wake(int irq, void *data)
+{
+	struct bcm_device *bdev = data;
+
+	bt_dev_dbg(bdev, "Host wake IRQ");
+
+	pm_runtime_get(&bdev->pdev->dev);
+	pm_runtime_mark_last_busy(&bdev->pdev->dev);
+	pm_runtime_put_autosuspend(&bdev->pdev->dev);
+
+	return IRQ_HANDLED;
+}
+
+static int bcm_request_irq(struct bcm_data *bcm)
+{
+	struct bcm_device *bdev = bcm->dev;
+	int err = 0;
+
+	/* If this is not a platform device, do not enable PM functionalities */
+	mutex_lock(&bcm_device_lock);
+	if (!bcm_device_exists(bdev)) {
+		err = -ENODEV;
+		goto unlock;
+	}
+
+	if (bdev->irq > 0) {
+		err = devm_request_irq(&bdev->pdev->dev, bdev->irq,
+				       bcm_host_wake, IRQF_TRIGGER_RISING,
+				       "host_wake", bdev);
+		if (err)
+			goto unlock;
+
+		device_init_wakeup(&bdev->pdev->dev, true);
+
+		pm_runtime_set_autosuspend_delay(&bdev->pdev->dev,
+						 BCM_AUTOSUSPEND_DELAY);
+		pm_runtime_use_autosuspend(&bdev->pdev->dev);
+		pm_runtime_set_active(&bdev->pdev->dev);
+		pm_runtime_enable(&bdev->pdev->dev);
+	}
+
+unlock:
+	mutex_unlock(&bcm_device_lock);
+
+	return err;
+}
+
+static const struct bcm_set_sleep_mode default_sleep_params = {
+	.sleep_mode = 1,	/* 0=Disabled, 1=UART, 2=Reserved, 3=USB */
+	.idle_host = 2,		/* idle threshold HOST, in 300ms */
+	.idle_dev = 2,		/* idle threshold device, in 300ms */
+	.bt_wake_active = 1,	/* BT_WAKE active mode: 1 = high, 0 = low */
+	.host_wake_active = 0,	/* HOST_WAKE active mode: 1 = high, 0 = low */
+	.allow_host_sleep = 1,	/* Allow host sleep in SCO flag */
+	.combine_modes = 1,	/* Combine sleep and LPM flag */
+	.tristate_control = 0,	/* Allow tri-state control of UART tx flag */
+	/* Irrelevant USB flags */
+	.usb_auto_sleep = 0,
+	.usb_resume_timeout = 0,
+	.pulsed_host_wake = 0,
+	.break_to_host = 0
+};
+
+static int bcm_setup_sleep(struct hci_uart *hu)
+{
+	struct bcm_data *bcm = hu->priv;
+	struct sk_buff *skb;
+	struct bcm_set_sleep_mode sleep_params = default_sleep_params;
+
+	sleep_params.host_wake_active = !bcm->dev->irq_polarity;
+
+	skb = __hci_cmd_sync(hu->hdev, 0xfc27, sizeof(sleep_params),
+			     &sleep_params, HCI_INIT_TIMEOUT);
+	if (IS_ERR(skb)) {
+		int err = PTR_ERR(skb);
+		bt_dev_err(hu->hdev, "Sleep VSC failed (%d)", err);
+		return err;
+	}
+	kfree_skb(skb);
+
+	bt_dev_dbg(hu->hdev, "Set Sleep Parameters VSC succeeded");
+
+	return 0;
+}
+#else
+static inline int bcm_request_irq(struct bcm_data *bcm) { return 0; }
+static inline int bcm_setup_sleep(struct hci_uart *hu) { return 0; }
+#endif
+
+static int bcm_set_diag(struct hci_dev *hdev, bool enable)
+{
+	struct hci_uart *hu = hci_get_drvdata(hdev);
+	struct bcm_data *bcm = hu->priv;
+	struct sk_buff *skb;
+
+	if (!test_bit(HCI_RUNNING, &hdev->flags))
+		return -ENETDOWN;
+
+	skb = bt_skb_alloc(3, GFP_KERNEL);
+	if (!skb)
+		return -ENOMEM;
+
+	*skb_put(skb, 1) = BCM_LM_DIAG_PKT;
+	*skb_put(skb, 1) = 0xf0;
+	*skb_put(skb, 1) = enable;
+
+	skb_queue_tail(&bcm->txq, skb);
+	hci_uart_tx_wakeup(hu);
+
+	return 0;
+}
+
 static int bcm_open(struct hci_uart *hu)
 {
 	struct bcm_data *bcm;
+	struct list_head *p;
 
-	BT_DBG("hu %p", hu);
+	bt_dev_dbg(hu->hdev, "hu %p", hu);
 
 	bcm = kzalloc(sizeof(*bcm), GFP_KERNEL);
 	if (!bcm)
@@ -49,14 +286,55 @@ static int bcm_open(struct hci_uart *hu)
 	skb_queue_head_init(&bcm->txq);
 
 	hu->priv = bcm;
+
+	mutex_lock(&bcm_device_lock);
+	list_for_each(p, &bcm_device_list) {
+		struct bcm_device *dev = list_entry(p, struct bcm_device, list);
+
+		/* Retrieve saved bcm_device based on parent of the
+		 * platform device (saved during device probe) and
+		 * parent of tty device used by hci_uart
+		 */
+		if (hu->tty->dev->parent == dev->pdev->dev.parent) {
+			bcm->dev = dev;
+			hu->init_speed = dev->init_speed;
+#ifdef CONFIG_PM
+			dev->hu = hu;
+#endif
+			bcm_gpio_set_power(bcm->dev, true);
+			break;
+		}
+	}
+
+	mutex_unlock(&bcm_device_lock);
+
 	return 0;
 }
 
 static int bcm_close(struct hci_uart *hu)
 {
 	struct bcm_data *bcm = hu->priv;
+	struct bcm_device *bdev = bcm->dev;
 
-	BT_DBG("hu %p", hu);
+	bt_dev_dbg(hu->hdev, "hu %p", hu);
+
+	/* Protect bcm->dev against removal of the device or driver */
+	mutex_lock(&bcm_device_lock);
+	if (bcm_device_exists(bdev)) {
+		bcm_gpio_set_power(bdev, false);
+#ifdef CONFIG_PM
+		pm_runtime_disable(&bdev->pdev->dev);
+		pm_runtime_set_suspended(&bdev->pdev->dev);
+
+		if (device_can_wakeup(&bdev->pdev->dev)) {
+			devm_free_irq(&bdev->pdev->dev, bdev->irq, bdev);
+			device_init_wakeup(&bdev->pdev->dev, false);
+		}
+
+		bdev->hu = NULL;
+#endif
+	}
+	mutex_unlock(&bcm_device_lock);
 
 	skb_queue_purge(&bcm->txq);
 	kfree_skb(bcm->rx_skb);
@@ -70,7 +348,7 @@ static int bcm_flush(struct hci_uart *hu)
 {
 	struct bcm_data *bcm = hu->priv;
 
-	BT_DBG("hu %p", hu);
+	bt_dev_dbg(hu->hdev, "hu %p", hu);
 
 	skb_queue_purge(&bcm->txq);
 
@@ -79,17 +357,84 @@ static int bcm_flush(struct hci_uart *hu)
 
 static int bcm_setup(struct hci_uart *hu)
 {
-	BT_DBG("hu %p", hu);
+	struct bcm_data *bcm = hu->priv;
+	char fw_name[64];
+	const struct firmware *fw;
+	unsigned int speed;
+	int err;
+
+	bt_dev_dbg(hu->hdev, "hu %p", hu);
 
+	hu->hdev->set_diag = bcm_set_diag;
 	hu->hdev->set_bdaddr = btbcm_set_bdaddr;
 
-	return btbcm_setup_patchram(hu->hdev);
+	err = btbcm_initialize(hu->hdev, fw_name, sizeof(fw_name));
+	if (err)
+		return err;
+
+	err = request_firmware(&fw, fw_name, &hu->hdev->dev);
+	if (err < 0) {
+		bt_dev_info(hu->hdev, "BCM: Patch %s not found", fw_name);
+		return 0;
+	}
+
+	err = btbcm_patchram(hu->hdev, fw);
+	if (err) {
+		bt_dev_info(hu->hdev, "BCM: Patch failed (%d)", err);
+		goto finalize;
+	}
+
+	/* Init speed if any */
+	if (hu->init_speed)
+		speed = hu->init_speed;
+	else if (hu->proto->init_speed)
+		speed = hu->proto->init_speed;
+	else
+		speed = 0;
+
+	if (speed)
+		hci_uart_set_baudrate(hu, speed);
+
+	/* Operational speed if any */
+	if (hu->oper_speed)
+		speed = hu->oper_speed;
+	else if (hu->proto->oper_speed)
+		speed = hu->proto->oper_speed;
+	else
+		speed = 0;
+
+	if (speed) {
+		err = bcm_set_baudrate(hu, speed);
+		if (!err)
+			hci_uart_set_baudrate(hu, speed);
+	}
+
+finalize:
+	release_firmware(fw);
+
+	err = btbcm_finalize(hu->hdev);
+	if (err)
+		return err;
+
+	err = bcm_request_irq(bcm);
+	if (!err)
+		err = bcm_setup_sleep(hu);
+
+	return err;
 }
 
+#define BCM_RECV_LM_DIAG \
+	.type = BCM_LM_DIAG_PKT, \
+	.hlen = BCM_LM_DIAG_SIZE, \
+	.loff = 0, \
+	.lsize = 0, \
+	.maxlen = BCM_LM_DIAG_SIZE
+
 static const struct h4_recv_pkt bcm_recv_pkts[] = {
-	{ H4_RECV_ACL,   .recv = hci_recv_frame },
-	{ H4_RECV_SCO,   .recv = hci_recv_frame },
-	{ H4_RECV_EVENT, .recv = hci_recv_frame },
+	{ H4_RECV_ACL,      .recv = hci_recv_frame },
+	{ H4_RECV_SCO,      .recv = hci_recv_frame },
+	{ H4_RECV_EVENT,    .recv = hci_recv_frame },
+	{ BCM_RECV_LM_DIAG, .recv = hci_recv_diag  },
 };
 
 static int bcm_recv(struct hci_uart *hu, const void *data, int count)
@@ -103,8 +448,18 @@ static int bcm_recv(struct hci_uart *hu, const void *data, int count)
 				  bcm_recv_pkts, ARRAY_SIZE(bcm_recv_pkts));
 	if (IS_ERR(bcm->rx_skb)) {
 		int err = PTR_ERR(bcm->rx_skb);
-		BT_ERR("%s: Frame reassembly failed (%d)", hu->hdev->name, err);
+		bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
+		bcm->rx_skb = NULL;
 		return err;
+	} else if (!bcm->rx_skb) {
+		/* Delay auto-suspend when receiving completed packet */
+		mutex_lock(&bcm_device_lock);
+		if (bcm->dev && bcm_device_exists(bcm->dev)) {
+			pm_runtime_get(&bcm->dev->pdev->dev);
+			pm_runtime_mark_last_busy(&bcm->dev->pdev->dev);
+			pm_runtime_put_autosuspend(&bcm->dev->pdev->dev);
+		}
+		mutex_unlock(&bcm_device_lock);
 	}
 
 	return count;
@@ -114,7 +469,7 @@ static int bcm_enqueue(struct hci_uart *hu, struct sk_buff *skb)
 {
 	struct bcm_data *bcm = hu->priv;
 
-	BT_DBG("hu %p skb %p", hu, skb);
+	bt_dev_dbg(hu->hdev, "hu %p skb %p", hu, skb);
 
 	/* Prepend skb with frame type */
 	memcpy(skb_push(skb, 1), &bt_cb(skb)->pkt_type, 1);
@@ -126,28 +481,372 @@ static int bcm_enqueue(struct hci_uart *hu, struct sk_buff *skb)
 static struct sk_buff *bcm_dequeue(struct hci_uart *hu)
 {
 	struct bcm_data *bcm = hu->priv;
+	struct sk_buff *skb = NULL;
+	struct bcm_device *bdev = NULL;
 
-	return skb_dequeue(&bcm->txq);
+	mutex_lock(&bcm_device_lock);
+
+	if (bcm_device_exists(bcm->dev)) {
+		bdev = bcm->dev;
+		pm_runtime_get_sync(&bdev->pdev->dev);
+		/* Shall be resumed here */
+	}
+
+	skb = skb_dequeue(&bcm->txq);
+
+	if (bdev) {
+		pm_runtime_mark_last_busy(&bdev->pdev->dev);
+		pm_runtime_put_autosuspend(&bdev->pdev->dev);
+	}
+
+	mutex_unlock(&bcm_device_lock);
+
+	return skb;
+}
+
+#ifdef CONFIG_PM
+static int bcm_suspend_device(struct device *dev)
+{
+	struct bcm_device *bdev = platform_get_drvdata(to_platform_device(dev));
+
+	bt_dev_dbg(bdev, "");
+
+	if (!bdev->is_suspended && bdev->hu) {
+		hci_uart_set_flow_control(bdev->hu, true);
+
+		/* Once this returns, driver suspends BT via GPIO */
+		bdev->is_suspended = true;
+	}
+
+	/* Suspend the device */
+	if (bdev->device_wakeup) {
+		gpiod_set_value(bdev->device_wakeup, false);
+		bt_dev_dbg(bdev, "suspend, delaying 15 ms");
+		mdelay(15);
+	}
+
+	return 0;
+}
+
+static int bcm_resume_device(struct device *dev)
+{
+	struct bcm_device *bdev = platform_get_drvdata(to_platform_device(dev));
+
+	bt_dev_dbg(bdev, "");
+
+	if (bdev->device_wakeup) {
+		gpiod_set_value(bdev->device_wakeup, true);
+		bt_dev_dbg(bdev, "resume, delaying 15 ms");
+		mdelay(15);
+	}
+
+	/* When this executes, the device has woken up already */
+	if (bdev->is_suspended && bdev->hu) {
+		bdev->is_suspended = false;
+
+		hci_uart_set_flow_control(bdev->hu, false);
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_PM_SLEEP
+/* Platform suspend callback */
+static int bcm_suspend(struct device *dev)
+{
+	struct bcm_device *bdev = platform_get_drvdata(to_platform_device(dev));
+	int error;
+
+	bt_dev_dbg(bdev, "suspend: is_suspended %d", bdev->is_suspended);
+
+	/* bcm_suspend can be called at any time as long as platform device is
+	 * bound, so it should use bcm_device_lock to protect access to hci_uart
+	 * and device_wake-up GPIO.
+	 */
+	mutex_lock(&bcm_device_lock);
+
+	if (!bdev->hu)
+		goto unlock;
+
+	if (pm_runtime_active(dev))
+		bcm_suspend_device(dev);
+
+	if (device_may_wakeup(&bdev->pdev->dev)) {
+		error = enable_irq_wake(bdev->irq);
+		if (!error)
+			bt_dev_dbg(bdev, "BCM irq: enabled");
+	}
+
+unlock:
+	mutex_unlock(&bcm_device_lock);
+
+	return 0;
+}
+
+/* Platform resume callback */
+static int bcm_resume(struct device *dev)
+{
+	struct bcm_device *bdev = platform_get_drvdata(to_platform_device(dev));
+
+	bt_dev_dbg(bdev, "resume: is_suspended %d", bdev->is_suspended);
+
+	/* bcm_resume can be called at any time as long as platform device is
+	 * bound, so it should use bcm_device_lock to protect access to hci_uart
+	 * and device_wake-up GPIO.
+	 */
+	mutex_lock(&bcm_device_lock);
+
+	if (!bdev->hu)
+		goto unlock;
+
+	if (device_may_wakeup(&bdev->pdev->dev)) {
+		disable_irq_wake(bdev->irq);
+		bt_dev_dbg(bdev, "BCM irq: disabled");
+	}
+
+	bcm_resume_device(dev);
+
+unlock:
+	mutex_unlock(&bcm_device_lock);
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
+}
+#endif
+
+static const struct acpi_gpio_params device_wakeup_gpios = { 0, 0, false };
+static const struct acpi_gpio_params shutdown_gpios = { 1, 0, false };
+static const struct acpi_gpio_params host_wakeup_gpios = { 2, 0, false };
+
+static const struct acpi_gpio_mapping acpi_bcm_default_gpios[] = {
+	{ "device-wakeup-gpios", &device_wakeup_gpios, 1 },
+	{ "shutdown-gpios", &shutdown_gpios, 1 },
+	{ "host-wakeup-gpios", &host_wakeup_gpios, 1 },
+	{ },
+};
+
+#ifdef CONFIG_ACPI
+static u8 acpi_active_low = ACPI_ACTIVE_LOW;
+
+/* IRQ polarity of some chipsets are not defined correctly in ACPI table. */
+static const struct dmi_system_id bcm_wrong_irq_dmi_table[] = {
+	{
+		.ident = "Asus T100TA",
+		.matches = {
+			DMI_EXACT_MATCH(DMI_SYS_VENDOR,
+					"ASUSTeK COMPUTER INC."),
+			DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "T100TA"),
+		},
+		.driver_data = &acpi_active_low,
+	},
+	{ }
+};
+
+static int bcm_resource(struct acpi_resource *ares, void *data)
+{
+	struct bcm_device *dev = data;
+	struct acpi_resource_extended_irq *irq;
+	struct acpi_resource_gpio *gpio;
+	struct acpi_resource_uart_serialbus *sb;
+
+	switch (ares->type) {
+	case ACPI_RESOURCE_TYPE_EXTENDED_IRQ:
+		irq = &ares->data.extended_irq;
+		dev->irq_polarity = irq->polarity;
+		break;
+
+	case ACPI_RESOURCE_TYPE_GPIO:
+		gpio = &ares->data.gpio;
+		if (gpio->connection_type == ACPI_RESOURCE_GPIO_TYPE_INT)
+			dev->irq_polarity = gpio->polarity;
+		break;
+
+	case ACPI_RESOURCE_TYPE_SERIAL_BUS:
+		sb = &ares->data.uart_serial_bus;
+		if (sb->type == ACPI_RESOURCE_SERIAL_TYPE_UART)
+			dev->init_speed = sb->default_baud_rate;
+		break;
+
+	default:
+		break;
+	}
+
+	/* Always tell the ACPI core to skip this resource */
+	return 1;
+}
+
+static int bcm_acpi_probe(struct bcm_device *dev)
+{
+	struct platform_device *pdev = dev->pdev;
+	LIST_HEAD(resources);
+	const struct dmi_system_id *dmi_id;
+	int ret;
+
+	/* Retrieve GPIO data */
+	dev->name = dev_name(&pdev->dev);
+	ret = acpi_dev_add_driver_gpios(ACPI_COMPANION(&pdev->dev),
+					acpi_bcm_default_gpios);
+	if (ret)
+		return ret;
+
+	dev->clk = devm_clk_get(&pdev->dev, NULL);
+
+	dev->device_wakeup = devm_gpiod_get_optional(&pdev->dev,
+						     "device-wakeup",
+						     GPIOD_OUT_LOW);
+	if (IS_ERR(dev->device_wakeup))
+		return PTR_ERR(dev->device_wakeup);
+
+	dev->shutdown = devm_gpiod_get_optional(&pdev->dev, "shutdown",
+						GPIOD_OUT_LOW);
+	if (IS_ERR(dev->shutdown))
+		return PTR_ERR(dev->shutdown);
+
+	/* IRQ can be declared in ACPI table as Interrupt or GpioInt */
+	dev->irq = platform_get_irq(pdev, 0);
+	if (dev->irq <= 0) {
+		struct gpio_desc *gpio;
+
+		gpio = devm_gpiod_get_optional(&pdev->dev, "host-wakeup",
+					       GPIOD_IN);
+		if (IS_ERR(gpio))
+			return PTR_ERR(gpio);
+
+		dev->irq = gpiod_to_irq(gpio);
+	}
+
+	dev_info(&pdev->dev, "BCM irq: %d\n", dev->irq);
+
+	/* Make sure at-least one of the GPIO is defined and that
+	 * a name is specified for this instance
+	 */
+	if ((!dev->device_wakeup && !dev->shutdown) || !dev->name) {
+		dev_err(&pdev->dev, "invalid platform data\n");
+		return -EINVAL;
+	}
+
+	/* Retrieve UART ACPI info */
+	ret = acpi_dev_get_resources(ACPI_COMPANION(&dev->pdev->dev),
+				     &resources, bcm_resource, dev);
+	if (ret < 0)
+		return ret;
+	acpi_dev_free_resource_list(&resources);
+
+	dmi_id = dmi_first_match(bcm_wrong_irq_dmi_table);
+	if (dmi_id) {
+		bt_dev_warn(dev, "%s: Overwriting IRQ polarity to active low",
+			    dmi_id->ident);
+		dev->irq_polarity = *(u8 *)dmi_id->driver_data;
+	}
+
+	return 0;
+}
+#else
+static int bcm_acpi_probe(struct bcm_device *dev)
+{
+	return -EINVAL;
+}
+#endif /* CONFIG_ACPI */
+
+static int bcm_probe(struct platform_device *pdev)
+{
+	struct bcm_device *dev;
+	int ret;
+
+	dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
+	if (!dev)
+		return -ENOMEM;
+
+	dev->pdev = pdev;
+
+	ret = bcm_acpi_probe(dev);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, dev);
+
+	dev_info(&pdev->dev, "%s device registered.\n", dev->name);
+
+	/* Place this instance on the device list */
+	mutex_lock(&bcm_device_lock);
+	list_add_tail(&dev->list, &bcm_device_list);
+	mutex_unlock(&bcm_device_lock);
+
+	bcm_gpio_set_power(dev, false);
+
+	return 0;
+}
+
+static int bcm_remove(struct platform_device *pdev)
+{
+	struct bcm_device *dev = platform_get_drvdata(pdev);
+
+	mutex_lock(&bcm_device_lock);
+	list_del(&dev->list);
+	mutex_unlock(&bcm_device_lock);
+
+	acpi_dev_remove_driver_gpios(ACPI_COMPANION(&pdev->dev));
+
+	dev_info(&pdev->dev, "%s device unregistered.\n", dev->name);
+
+	return 0;
 }
 
 static const struct hci_uart_proto bcm_proto = {
 	.id		= HCI_UART_BCM,
 	.name		= "BCM",
+	.manufacturer	= 15,
+	.init_speed	= 115200,
+	.oper_speed	= 4000000,
 	.open		= bcm_open,
 	.close		= bcm_close,
 	.flush		= bcm_flush,
 	.setup		= bcm_setup,
+	.set_baudrate	= bcm_set_baudrate,
 	.recv		= bcm_recv,
 	.enqueue	= bcm_enqueue,
 	.dequeue	= bcm_dequeue,
 };
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id bcm_acpi_match[] = {
+	{ "BCM2E39", 0 },
+	{ "BCM2E67", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, bcm_acpi_match);
+#endif
+
+/* Platform suspend and resume callbacks */
+static const struct dev_pm_ops bcm_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(bcm_suspend, bcm_resume)
+	SET_RUNTIME_PM_OPS(bcm_suspend_device, bcm_resume_device, NULL)
+};
+
+static struct platform_driver bcm_driver = {
+	.probe = bcm_probe,
+	.remove = bcm_remove,
+	.driver = {
+		.name = "hci_bcm",
+		.acpi_match_table = ACPI_PTR(bcm_acpi_match),
+		.pm = &bcm_pm_ops,
+	},
+};
+
 int __init bcm_init(void)
 {
+	platform_driver_register(&bcm_driver);
+
 	return hci_uart_register_proto(&bcm_proto);
 }
 
 int __exit bcm_deinit(void)
 {
+	platform_driver_unregister(&bcm_driver);
+
 	return hci_uart_unregister_proto(&bcm_proto);
 }