diff options
author | 2016-04-11 10:41:07 +0300 | |
---|---|---|
committer | 2016-04-13 08:17:18 +0300 | |
commit | e09b41010ba33a20a87472ee821fa407a5b8da36 (patch) | |
tree | d10dc367189862e7ca5c592f033dc3726e1df4e3 /kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi | |
parent | f93b97fd65072de626c074dbe099a1fff05ce060 (diff) |
These changes are the raw update to linux-4.4.6-rt14. Kernel sources
are taken from kernel.org, and rt patch from the rt wiki download page.
During the rebasing, the following patch collided:
Force tick interrupt and get rid of softirq magic(I70131fb85).
Collisions have been removed because its logic was found on the
source already.
Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>
Diffstat (limited to 'kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi')
-rw-r--r-- | kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi | 56 |
1 files changed, 51 insertions, 5 deletions
diff --git a/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi b/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi index 782ab1ff1..cfe140c65 100644 --- a/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/kernel/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -199,6 +199,38 @@ gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ }; }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */ + vcc-supply = <&vaux2>; + }; + + /* HS USB Host VBUS supply + * disabling this regulator causes current leakage, and LCD flicker + * on earlier (CC) board revisions, so keep it always on */ + usb_host_5v: fixed-regulator-usb_host_5v { + compatible = "regulator-fixed"; + regulator-name = "usb_host_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* GPIO_164 */ + }; + + /* wg7210 (wifi+bt module) 32k clock buffer */ + wg7210_32k: fixed-regulator-wg7210_32k { + compatible = "regulator-fixed"; + regulator-name = "wg7210_32k"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + enable-active-high; + gpio = <&twl_gpio 13 GPIO_ACTIVE_HIGH>; + }; }; &omap3_pmx_core { @@ -459,13 +491,18 @@ power = <50>; }; +/* + * Many pandora boards have been produced with defective write-protect switches + * on either slot, so it was decided not to use this feature. If you know + * your board has good switches, feel free to uncomment wp-gpios below. + */ &mmc1 { pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc1>; bus-width = <4>; cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */ + /*wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;*/ /* GPIO_126 */ }; &mmc2 { @@ -473,8 +510,13 @@ pinctrl-0 = <&mmc2_pins>; vmmc-supply = <&vmmc2>; bus-width = <4>; - cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>; - wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */ + cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>; + /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/ /* GPIO_127 */ +}; + +/* mmc3 is probed using pdata-quirks to pass wl1251 card data */ +&mmc3 { + status = "disabled"; }; /* bluetooth*/ @@ -496,6 +538,10 @@ port2-mode = "ehci-phy"; }; +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + &gpmc { ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ @@ -545,7 +591,7 @@ reg = <0x280000 0xa00000>; }; - filesystem@680000 { + filesystem@c80000 { label = "rootfs"; reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ }; @@ -561,7 +607,7 @@ pinctrl-0 = <&penirq_pins>; interrupt-parent = <&gpio3>; interrupts = <30 0>; /* GPIO_94 */ - pendown-gpio = <&gpio3 30 0>; + pendown-gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; vcc-supply = <&vaux4>; ti,x-min = /bits/ 16 <0>; |