These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 736 insertions, 0 deletions

diff --git a/kernel/arch/arm/boot/dts/imx6ul.dtsi b/kernel/arch/arm/boot/dts/imx6ul.dtsi
new file mode 100644
index 000000000..d00e994bd
--- /dev/null
+++ b/kernel/arch/arm/boot/dts/imx6ul.dtsi
@@ -0,0 +1,736 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx6ul-pinfunc.h"
+#include "skeleton.dtsi"
+
+/ {
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+		serial6 = &uart7;
+		serial7 = &uart8;
+		spi0 = &ecspi1;
+		spi1 = &ecspi2;
+		spi2 = &ecspi3;
+		spi3 = &ecspi4;
+		usbphy0 = &usbphy1;
+		usbphy1 = &usbphy2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+			clock-latency = <61036>; /* two CLK32 periods */
+			operating-points = <
+				/* kHz	uV */
+				528000	1250000
+				396000	1150000
+				198000	1150000
+			>;
+			fsl,soc-operating-points = <
+				/* KHz	uV */
+				528000	1250000
+				396000	1150000
+				198000	1150000
+			>;
+			clocks = <&clks IMX6UL_CLK_ARM>,
+				 <&clks IMX6UL_CLK_PLL2_BUS>,
+				 <&clks IMX6UL_CLK_PLL2_PFD2>,
+				 <&clks IMX6UL_CA7_SECONDARY_SEL>,
+				 <&clks IMX6UL_CLK_STEP>,
+				 <&clks IMX6UL_CLK_PLL1_SW>,
+				 <&clks IMX6UL_CLK_PLL1_SYS>,
+				 <&clks IMX6UL_PLL1_BYPASS>,
+				 <&clks IMX6UL_CLK_PLL1>,
+				 <&clks IMX6UL_PLL1_BYPASS_SRC>,
+				 <&clks IMX6UL_CLK_OSC>;
+			clock-names = "arm", "pll2_bus",  "pll2_pfd2_396m",
+				      "secondary_sel", "step", "pll1_sw",
+				      "pll1_sys", "pll1_bypass", "pll1",
+				      "pll1_bypass_src", "osc";
+			arm-supply = <&reg_arm>;
+			soc-supply = <&reg_soc>;
+		};
+	};
+
+	intc: interrupt-controller@00a01000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x00a01000 0x1000>,
+		      <0x00a02000 0x1000>,
+		      <0x00a04000 0x2000>,
+		      <0x00a06000 0x2000>;
+	};
+
+	ckil: clock-cli {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "ckil";
+	};
+
+	osc: clock-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "osc";
+	};
+
+	ipp_di0: clock-di0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+		clock-output-names = "ipp_di0";
+	};
+
+	ipp_di1: clock-di1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+		clock-output-names = "ipp_di1";
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gpc>;
+		ranges;
+
+		pmu {
+			compatible = "arm,cortex-a7-pmu";
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		ocram: sram@00900000 {
+			compatible = "mmio-sram";
+			reg = <0x00900000 0x20000>;
+		};
+
+		aips1: aips-bus@02000000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x02000000 0x100000>;
+			ranges;
+
+			spba-bus@02000000 {
+				compatible = "fsl,spba-bus", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0x02000000 0x40000>;
+				ranges;
+
+				ecspi1: ecspi@02008000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+					reg = <0x02008000 0x4000>;
+					interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_ECSPI1>,
+						 <&clks IMX6UL_CLK_ECSPI1>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ecspi2: ecspi@0200c000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+					reg = <0x0200c000 0x4000>;
+					interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_ECSPI2>,
+						 <&clks IMX6UL_CLK_ECSPI2>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ecspi3: ecspi@02010000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+					reg = <0x02010000 0x4000>;
+					interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_ECSPI3>,
+						 <&clks IMX6UL_CLK_ECSPI3>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ecspi4: ecspi@02014000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+					reg = <0x02014000 0x4000>;
+					interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_ECSPI4>,
+						 <&clks IMX6UL_CLK_ECSPI4>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart7: serial@02018000 {
+					compatible = "fsl,imx6ul-uart",
+						     "fsl,imx6q-uart";
+					reg = <0x02018000 0x4000>;
+					interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_UART7_IPG>,
+						 <&clks IMX6UL_CLK_UART7_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart1: serial@02020000 {
+					compatible = "fsl,imx6ul-uart",
+						     "fsl,imx6q-uart";
+					reg = <0x02020000 0x4000>;
+					interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_UART1_IPG>,
+						 <&clks IMX6UL_CLK_UART1_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				uart8: serial@02024000 {
+					compatible = "fsl,imx6ul-uart",
+						     "fsl,imx6q-uart";
+					reg = <0x02024000 0x4000>;
+					interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clks IMX6UL_CLK_UART8_IPG>,
+						 <&clks IMX6UL_CLK_UART8_SERIAL>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+			};
+
+			gpt1: gpt@02098000 {
+				compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
+				reg = <0x02098000 0x4000>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_GPT1_BUS>,
+					 <&clks IMX6UL_CLK_GPT1_SERIAL>;
+				clock-names = "ipg", "per";
+			};
+
+			gpio1: gpio@0209c000 {
+				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+				reg = <0x0209c000 0x4000>;
+				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio2: gpio@020a0000 {
+				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+				reg = <0x020a0000 0x4000>;
+				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio3: gpio@020a4000 {
+				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+				reg = <0x020a4000 0x4000>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio4: gpio@020a8000 {
+				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+				reg = <0x020a8000 0x4000>;
+				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio5: gpio@020ac000 {
+				compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+				reg = <0x020ac000 0x4000>;
+				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			fec2: ethernet@020b4000 {
+				compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
+				reg = <0x020b4000 0x4000>;
+				interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_ENET>,
+					 <&clks IMX6UL_CLK_ENET_AHB>,
+					 <&clks IMX6UL_CLK_ENET_PTP>,
+					 <&clks IMX6UL_CLK_ENET2_REF_125M>,
+					 <&clks IMX6UL_CLK_ENET2_REF_125M>;
+				clock-names = "ipg", "ahb", "ptp",
+					      "enet_clk_ref", "enet_out";
+				fsl,num-tx-queues=<1>;
+				fsl,num-rx-queues=<1>;
+				status = "disabled";
+			};
+
+			wdog1: wdog@020bc000 {
+				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
+				reg = <0x020bc000 0x4000>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_WDOG1>;
+			};
+
+			wdog2: wdog@020c0000 {
+				compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
+				reg = <0x020c0000 0x4000>;
+				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_WDOG2>;
+				status = "disabled";
+			};
+
+			clks: ccm@020c4000 {
+				compatible = "fsl,imx6ul-ccm";
+				reg = <0x020c4000 0x4000>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+				#clock-cells = <1>;
+				clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>;
+				clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
+			};
+
+			anatop: anatop@020c8000 {
+				compatible = "fsl,imx6ul-anatop", "fsl,imx6q-anatop",
+					     "syscon", "simple-bus";
+				reg = <0x020c8000 0x1000>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+
+				reg_3p0: regulator-3p0@120 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd3p0";
+					regulator-min-microvolt = <2625000>;
+					regulator-max-microvolt = <3400000>;
+					anatop-reg-offset = <0x120>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <0>;
+					anatop-min-voltage = <2625000>;
+					anatop-max-voltage = <3400000>;
+					anatop-enable-bit = <0>;
+				};
+
+				reg_arm: regulator-vddcore@140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "cpu";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <0>;
+					anatop-vol-bit-width = <5>;
+					anatop-delay-reg-offset = <0x170>;
+					anatop-delay-bit-shift = <24>;
+					anatop-delay-bit-width = <2>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+
+				reg_soc: regulator-vddsoc@140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vddsoc";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <18>;
+					anatop-vol-bit-width = <5>;
+					anatop-delay-reg-offset = <0x170>;
+					anatop-delay-bit-shift = <28>;
+					anatop-delay-bit-width = <2>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+			};
+
+			usbphy1: usbphy@020c9000 {
+				compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
+				reg = <0x020c9000 0x1000>;
+				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_USBPHY1>;
+				phy-3p0-supply = <&reg_3p0>;
+				fsl,anatop = <&anatop>;
+			};
+
+			usbphy2: usbphy@020ca000 {
+				compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
+				reg = <0x020ca000 0x1000>;
+				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_USBPHY2>;
+				phy-3p0-supply = <&reg_3p0>;
+				fsl,anatop = <&anatop>;
+			};
+
+			snvs: snvs@020cc000 {
+				compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
+				reg = <0x020cc000 0x4000>;
+
+				snvs_rtc: snvs-rtc-lp {
+					compatible = "fsl,sec-v4.0-mon-rtc-lp";
+					regmap = <&snvs>;
+					offset = <0x34>;
+					interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+				};
+
+				snvs_poweroff: snvs-poweroff {
+					compatible = "syscon-poweroff";
+					regmap = <&snvs>;
+					offset = <0x38>;
+					mask = <0x60>;
+					status = "disabled";
+				};
+
+				snvs_pwrkey: snvs-powerkey {
+					compatible = "fsl,sec-v4.0-pwrkey";
+					regmap = <&snvs>;
+					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+					linux,keycode = <KEY_POWER>;
+					wakeup-source;
+				};
+			};
+
+			epit1: epit@020d0000 {
+				reg = <0x020d0000 0x4000>;
+				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			epit2: epit@020d4000 {
+				reg = <0x020d4000 0x4000>;
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			src: src@020d8000 {
+				compatible = "fsl,imx6ul-src", "fsl,imx51-src";
+				reg = <0x020d8000 0x4000>;
+				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+				#reset-cells = <1>;
+			};
+
+			gpc: gpc@020dc000 {
+				compatible = "fsl,imx6ul-gpc", "fsl,imx6q-gpc";
+				reg = <0x020dc000 0x4000>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&intc>;
+			};
+
+			iomuxc: iomuxc@020e0000 {
+				compatible = "fsl,imx6ul-iomuxc";
+				reg = <0x020e0000 0x4000>;
+			};
+
+			gpr: iomuxc-gpr@020e4000 {
+				compatible = "fsl,imx6ul-iomuxc-gpr", "syscon";
+				reg = <0x020e4000 0x4000>;
+			};
+
+			gpt2: gpt@020e8000 {
+				compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
+				reg = <0x020e8000 0x4000>;
+				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_DUMMY>,
+					 <&clks IMX6UL_CLK_DUMMY>;
+				clock-names = "ipg", "per";
+			};
+
+			pwm5: pwm@020f0000 {
+				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+				reg = <0x020f0000 0x4000>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_DUMMY>,
+					 <&clks IMX6UL_CLK_DUMMY>;
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+			};
+
+			pwm6: pwm@020f4000 {
+				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+				reg = <0x020f4000 0x4000>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_DUMMY>,
+					 <&clks IMX6UL_CLK_DUMMY>;
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+			};
+
+			pwm7: pwm@020f8000 {
+				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+				reg = <0x020f8000 0x4000>;
+				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_DUMMY>,
+					 <&clks IMX6UL_CLK_DUMMY>;
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+			};
+
+			pwm8: pwm@020fc000 {
+				compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+				reg = <0x020fc000 0x4000>;
+				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_DUMMY>,
+					 <&clks IMX6UL_CLK_DUMMY>;
+				clock-names = "ipg", "per";
+				#pwm-cells = <2>;
+			};
+		};
+
+		aips2: aips-bus@02100000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x02100000 0x100000>;
+			ranges;
+
+			usbotg1: usb@02184000 {
+				compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
+				reg = <0x02184000 0x200>;
+				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_USBOH3>;
+				fsl,usbphy = <&usbphy1>;
+				fsl,usbmisc = <&usbmisc 0>;
+				fsl,anatop = <&anatop>;
+				status = "disabled";
+			};
+
+			usbotg2: usb@02184200 {
+				compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
+				reg = <0x02184200 0x200>;
+				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_USBOH3>;
+				fsl,usbphy = <&usbphy2>;
+				fsl,usbmisc = <&usbmisc 1>;
+				status = "disabled";
+			};
+
+			usbmisc: usbmisc@02184800 {
+				#index-cells = <1>;
+				compatible = "fsl,imx6ul-usbmisc", "fsl,imx6q-usbmisc";
+				reg = <0x02184800 0x200>;
+			};
+
+			fec1: ethernet@02188000 {
+				compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
+				reg = <0x02188000 0x4000>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_ENET>,
+					 <&clks IMX6UL_CLK_ENET_AHB>,
+					 <&clks IMX6UL_CLK_ENET_PTP>,
+					 <&clks IMX6UL_CLK_ENET_REF>,
+					 <&clks IMX6UL_CLK_ENET_REF>;
+				clock-names = "ipg", "ahb", "ptp",
+					      "enet_clk_ref", "enet_out";
+				fsl,num-tx-queues=<1>;
+				fsl,num-rx-queues=<1>;
+				status = "disabled";
+			};
+
+			tsc: tsc@02040000 {
+				compatible = "fsl,imx6ul-tsc";
+				reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_IPG>,
+					 <&clks IMX6UL_CLK_ADC2>;
+				clock-names = "tsc", "adc";
+				status = "disabled";
+			};
+
+			usdhc1: usdhc@02190000 {
+				compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
+				reg = <0x02190000 0x4000>;
+				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_USDHC1>,
+					 <&clks IMX6UL_CLK_USDHC1>,
+					 <&clks IMX6UL_CLK_USDHC1>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc2: usdhc@02194000 {
+				compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
+				reg = <0x02194000 0x4000>;
+				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_USDHC2>,
+					 <&clks IMX6UL_CLK_USDHC2>,
+					 <&clks IMX6UL_CLK_USDHC2>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@021a0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+				reg = <0x021a0000 0x4000>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_I2C1>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@021a4000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+				reg = <0x021a4000 0x4000>;
+				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_I2C2>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@021a8000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+				reg = <0x021a8000 0x4000>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_I2C3>;
+				status = "disabled";
+			};
+
+			mmdc: mmdc@021b0000 {
+				compatible = "fsl,imx6ul-mmdc", "fsl,imx6q-mmdc";
+				reg = <0x021b0000 0x4000>;
+			};
+
+			qspi: qspi@021e0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
+				reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
+				reg-names = "QuadSPI", "QuadSPI-memory";
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_QSPI>,
+					 <&clks IMX6UL_CLK_QSPI>;
+				clock-names = "qspi_en", "qspi";
+				status = "disabled";
+			};
+
+			uart2: serial@021e8000 {
+				compatible = "fsl,imx6ul-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x021e8000 0x4000>;
+				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_UART2_IPG>,
+					 <&clks IMX6UL_CLK_UART2_SERIAL>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart3: serial@021ec000 {
+				compatible = "fsl,imx6ul-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x021ec000 0x4000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_UART3_IPG>,
+					 <&clks IMX6UL_CLK_UART3_SERIAL>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart4: serial@021f0000 {
+				compatible = "fsl,imx6ul-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x021f0000 0x4000>;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_UART4_IPG>,
+					 <&clks IMX6UL_CLK_UART4_SERIAL>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			uart5: serial@021f4000 {
+				compatible = "fsl,imx6ul-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x021f4000 0x4000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_UART5_IPG>,
+					 <&clks IMX6UL_CLK_UART5_SERIAL>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			i2c4: i2c@021f8000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+				reg = <0x021f8000 0x4000>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_I2C4>;
+				status = "disabled";
+			};
+
+			uart6: serial@021fc000 {
+				compatible = "fsl,imx6ul-uart",
+					     "fsl,imx6q-uart";
+				reg = <0x021fc000 0x4000>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX6UL_CLK_UART6_IPG>,
+					 <&clks IMX6UL_CLK_UART6_SERIAL>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+		};
+	};
+};