summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/w1/masters
diff options
context:
space:
mode:
authorYunhong Jiang <yunhong.jiang@intel.com>2015-08-04 12:17:53 -0700
committerYunhong Jiang <yunhong.jiang@intel.com>2015-08-04 15:44:42 -0700
commit9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00 (patch)
tree1c9cafbcd35f783a87880a10f85d1a060db1a563 /kernel/Documentation/w1/masters
parent98260f3884f4a202f9ca5eabed40b1354c489b29 (diff)
Add the rt linux 4.1.3-rt3 as base
Import the rt linux 4.1.3-rt3 as OPNFV kvm base. It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and the base is: commit 0917f823c59692d751951bf5ea699a2d1e2f26a2 Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Date: Sat Jul 25 12:13:34 2015 +0200 Prepare v4.1.3-rt3 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> We lose all the git history this way and it's not good. We should apply another opnfv project repo in future. Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423 Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Diffstat (limited to 'kernel/Documentation/w1/masters')
-rw-r--r--kernel/Documentation/w1/masters/00-INDEX12
-rw-r--r--kernel/Documentation/w1/masters/ds248231
-rw-r--r--kernel/Documentation/w1/masters/ds249068
-rw-r--r--kernel/Documentation/w1/masters/mxc-w112
-rw-r--r--kernel/Documentation/w1/masters/omap-hdq46
-rw-r--r--kernel/Documentation/w1/masters/w1-gpio33
6 files changed, 202 insertions, 0 deletions
diff --git a/kernel/Documentation/w1/masters/00-INDEX b/kernel/Documentation/w1/masters/00-INDEX
new file mode 100644
index 000000000..8330cf932
--- /dev/null
+++ b/kernel/Documentation/w1/masters/00-INDEX
@@ -0,0 +1,12 @@
+00-INDEX
+ - This file
+ds2482
+ - The Maxim/Dallas Semiconductor DS2482 provides 1-wire busses.
+ds2490
+ - The Maxim/Dallas Semiconductor DS2490 builds USB <-> W1 bridges.
+mxc-w1
+ - W1 master controller driver found on Freescale MX2/MX3 SoCs
+omap-hdq
+ - HDQ/1-wire module of TI OMAP 2430/3430.
+w1-gpio
+ - GPIO 1-wire bus master driver.
diff --git a/kernel/Documentation/w1/masters/ds2482 b/kernel/Documentation/w1/masters/ds2482
new file mode 100644
index 000000000..56f8edace
--- /dev/null
+++ b/kernel/Documentation/w1/masters/ds2482
@@ -0,0 +1,31 @@
+Kernel driver ds2482
+====================
+
+Supported chips:
+ * Maxim DS2482-100, Maxim DS2482-800
+ Prefix: 'ds2482'
+ Addresses scanned: None
+ Datasheets:
+ http://datasheets.maxim-ic.com/en/ds/DS2482-100.pdf
+ http://datasheets.maxim-ic.com/en/ds/DS2482-800.pdf
+
+Author: Ben Gardner <bgardner@wabtec.com>
+
+
+Description
+-----------
+
+The Maxim/Dallas Semiconductor DS2482 is a I2C device that provides
+one (DS2482-100) or eight (DS2482-800) 1-wire busses.
+
+
+General Remarks
+---------------
+
+Valid addresses are 0x18, 0x19, 0x1a, and 0x1b.
+However, the device cannot be detected without writing to the i2c bus, so no
+detection is done. You should instantiate the device explicitly.
+
+$ modprobe ds2482
+$ echo ds2482 0x18 > /sys/bus/i2c/devices/i2c-0/new_device
+
diff --git a/kernel/Documentation/w1/masters/ds2490 b/kernel/Documentation/w1/masters/ds2490
new file mode 100644
index 000000000..3e091151d
--- /dev/null
+++ b/kernel/Documentation/w1/masters/ds2490
@@ -0,0 +1,68 @@
+Kernel driver ds2490
+====================
+
+Supported chips:
+ * Maxim DS2490 based
+
+Author: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
+
+
+Description
+-----------
+
+The Maxim/Dallas Semiconductor DS2490 is a chip
+which allows to build USB <-> W1 bridges.
+
+DS9490(R) is a USB <-> W1 bus master device
+which has 0x81 family ID integrated chip and DS2490
+low-level operational chip.
+
+Notes and limitations.
+- The weak pullup current is a minimum of 0.9mA and maximum of 6.0mA.
+- The 5V strong pullup is supported with a minimum of 5.9mA and a
+ maximum of 30.4 mA. (From DS2490.pdf)
+- The hardware will detect when devices are attached to the bus on the
+ next bus (reset?) operation, however only a message is printed as
+ the core w1 code doesn't make use of the information. Connecting
+ one device tends to give multiple new device notifications.
+- The number of USB bus transactions could be reduced if w1_reset_send
+ was added to the API. The name is just a suggestion. It would take
+ a write buffer and a read buffer (along with sizes) as arguments.
+ The ds2490 block I/O command supports reset, write buffer, read
+ buffer, and strong pullup all in one command, instead of the current
+ 1 reset bus, 2 write the match rom command and slave rom id, 3 block
+ write and read data. The write buffer needs to have the match rom
+ command and slave rom id prepended to the front of the requested
+ write buffer, both of which are known to the driver.
+- The hardware supports normal, flexible, and overdrive bus
+ communication speeds, but only the normal is supported.
+- The registered w1_bus_master functions don't define error
+ conditions. If a bus search is in progress and the ds2490 is
+ removed it can produce a good amount of error output before the bus
+ search finishes.
+- The hardware supports detecting some error conditions, such as
+ short, alarming presence on reset, and no presence on reset, but the
+ driver doesn't query those values.
+- The ds2490 specification doesn't cover short bulk in reads in
+ detail, but my observation is if fewer bytes are requested than are
+ available, the bulk read will return an error and the hardware will
+ clear the entire bulk in buffer. It would be possible to read the
+ maximum buffer size to not run into this error condition, only extra
+ bytes in the buffer is a logic error in the driver. The code should
+ should match reads and writes as well as data sizes. Reads and
+ writes are serialized and the status verifies that the chip is idle
+ (and data is available) before the read is executed, so it should
+ not happen.
+- Running x86_64 2.6.24 UHCI under qemu 0.9.0 under x86_64 2.6.22-rc6
+ with a OHCI controller, ds2490 running in the guest would operate
+ normally the first time the module was loaded after qemu attached
+ the ds2490 hardware, but if the module was unloaded, then reloaded
+ most of the time one of the bulk out or in, and usually the bulk in
+ would fail. qemu sets a 50ms timeout and the bulk in would timeout
+ even when the status shows data available. A bulk out write would
+ show a successful completion, but the ds2490 status register would
+ show 0 bytes written. Detaching qemu from the ds2490 hardware and
+ reattaching would clear the problem. usbmon output in the guest and
+ host did not explain the problem. My guess is a bug in either qemu
+ or the host OS and more likely the host OS.
+-- 03-06-2008 David Fries <David@Fries.net>
diff --git a/kernel/Documentation/w1/masters/mxc-w1 b/kernel/Documentation/w1/masters/mxc-w1
new file mode 100644
index 000000000..38be1ad65
--- /dev/null
+++ b/kernel/Documentation/w1/masters/mxc-w1
@@ -0,0 +1,12 @@
+Kernel driver mxc_w1
+====================
+
+Supported chips:
+ * Freescale MX27, MX31 and probably other i.MX SoCs
+ Datasheets:
+ http://www.freescale.com/files/32bit/doc/data_sheet/MCIMX31.pdf?fpsp=1
+ http://cache.freescale.com/files/dsp/doc/archive/MCIMX27.pdf?fsrch=1&WT_TYPE=
+ Data%20Sheets&WT_VENDOR=FREESCALE&WT_FILE_FORMAT=pdf&WT_ASSET=Documentation
+
+Author: Originally based on Freescale code, prepared for mainline by
+ Sascha Hauer <s.hauer@pengutronix.de>
diff --git a/kernel/Documentation/w1/masters/omap-hdq b/kernel/Documentation/w1/masters/omap-hdq
new file mode 100644
index 000000000..884dc284b
--- /dev/null
+++ b/kernel/Documentation/w1/masters/omap-hdq
@@ -0,0 +1,46 @@
+Kernel driver for omap HDQ/1-wire module.
+========================================
+
+Supported chips:
+================
+ HDQ/1-wire controller on the TI OMAP 2430/3430 platforms.
+
+A useful link about HDQ basics:
+===============================
+http://focus.ti.com/lit/an/slua408a/slua408a.pdf
+
+Description:
+============
+The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
+protocol of the master functions of the Benchmark HDQ and the Dallas
+Semiconductor 1-Wire protocols. These protocols use a single wire for
+communication between the master (HDQ/1-Wire controller) and the slave
+(HDQ/1-Wire external compliant device).
+
+A typical application of the HDQ/1-Wire module is the communication with battery
+monitor (gas gauge) integrated circuits.
+
+The controller supports operation in both HDQ and 1-wire mode. The essential
+difference between the HDQ and 1-wire mode is how the slave device responds to
+initialization pulse.In HDQ mode, the firmware does not require the host to
+create an initialization pulse to the slave.However, the slave can be reset by
+using an initialization pulse (also referred to as a break pulse).The slave
+does not respond with a presence pulse as it does in the 1-Wire protocol.
+
+Remarks:
+========
+The driver (drivers/w1/masters/omap_hdq.c) supports the HDQ mode of the
+controller. In this mode, as we can not read the ID which obeys the W1
+spec(family:id:crc), a module parameter can be passed to the driver which will
+be used to calculate the CRC and pass back an appropriate slave ID to the W1
+core.
+
+By default the master driver and the BQ slave i/f
+driver(drivers/w1/slaves/w1_bq27000.c) sets the ID to 1.
+Please note to load both the modules with a different ID if required, but note
+that the ID used should be same for both master and slave driver loading.
+
+e.g:
+insmod omap_hdq.ko W1_ID=2
+inamod w1_bq27000.ko F_ID=2
+
diff --git a/kernel/Documentation/w1/masters/w1-gpio b/kernel/Documentation/w1/masters/w1-gpio
new file mode 100644
index 000000000..af5d3b4aa
--- /dev/null
+++ b/kernel/Documentation/w1/masters/w1-gpio
@@ -0,0 +1,33 @@
+Kernel driver w1-gpio
+=====================
+
+Author: Ville Syrjala <syrjala@sci.fi>
+
+
+Description
+-----------
+
+GPIO 1-wire bus master driver. The driver uses the GPIO API to control the
+wire and the GPIO pin can be specified using platform data.
+
+
+Example (mach-at91)
+-------------------
+
+#include <linux/w1-gpio.h>
+
+static struct w1_gpio_platform_data foo_w1_gpio_pdata = {
+ .pin = AT91_PIN_PB20,
+ .is_open_drain = 1,
+};
+
+static struct platform_device foo_w1_device = {
+ .name = "w1-gpio",
+ .id = -1,
+ .dev.platform_data = &foo_w1_gpio_pdata,
+};
+
+...
+ at91_set_GPIO_periph(foo_w1_gpio_pdata.pin, 1);
+ at91_set_multi_drive(foo_w1_gpio_pdata.pin, 1);
+ platform_device_register(&foo_w1_device);