summaryrefslogtreecommitdiffstats
path: root/kernel/Documentation/power
diff options
context:
space:
mode:
authorJosé Pekkarinen <jose.pekkarinen@nokia.com>2016-04-11 10:41:07 +0300
committerJosé Pekkarinen <jose.pekkarinen@nokia.com>2016-04-13 08:17:18 +0300
commite09b41010ba33a20a87472ee821fa407a5b8da36 (patch)
treed10dc367189862e7ca5c592f033dc3726e1df4e3 /kernel/Documentation/power
parentf93b97fd65072de626c074dbe099a1fff05ce060 (diff)
These changes are the raw update to linux-4.4.6-rt14. Kernel sources
are taken from kernel.org, and rt patch from the rt wiki download page. During the rebasing, the following patch collided: Force tick interrupt and get rid of softirq magic(I70131fb85). Collisions have been removed because its logic was found on the source already. Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769 Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>
Diffstat (limited to 'kernel/Documentation/power')
-rw-r--r--kernel/Documentation/power/devices.txt7
-rw-r--r--kernel/Documentation/power/pci.txt51
-rw-r--r--kernel/Documentation/power/runtime_pm.txt10
-rw-r--r--kernel/Documentation/power/suspend-and-cpuhotplug.txt6
-rw-r--r--kernel/Documentation/power/swsusp.txt13
5 files changed, 65 insertions, 22 deletions
diff --git a/kernel/Documentation/power/devices.txt b/kernel/Documentation/power/devices.txt
index d172bce0f..8ba6625fd 100644
--- a/kernel/Documentation/power/devices.txt
+++ b/kernel/Documentation/power/devices.txt
@@ -341,6 +341,13 @@ the phases are:
and is entirely responsible for bringing the device back to the
functional state as appropriate.
+ Note that this direct-complete procedure applies even if the device is
+ disabled for runtime PM; only the runtime-PM status matters. It follows
+ that if a device has system-sleep callbacks but does not support runtime
+ PM, then its prepare callback must never return a positive value. This
+ is because all devices are initially set to runtime-suspended with
+ runtime PM disabled.
+
2. The suspend methods should quiesce the device to stop it from performing
I/O. They also may save the device registers and put it into the
appropriate low-power state, depending on the bus type the device is on,
diff --git a/kernel/Documentation/power/pci.txt b/kernel/Documentation/power/pci.txt
index 62328d76b..b0e911e0e 100644
--- a/kernel/Documentation/power/pci.txt
+++ b/kernel/Documentation/power/pci.txt
@@ -979,20 +979,45 @@ every time right after the runtime_resume() callback has returned
(alternatively, the runtime_suspend() callback will have to check if the
device should really be suspended and return -EAGAIN if that is not the case).
-The runtime PM of PCI devices is disabled by default. It is also blocked by
-pci_pm_init() that runs the pm_runtime_forbid() helper function. If a PCI
-driver implements the runtime PM callbacks and intends to use the runtime PM
-framework provided by the PM core and the PCI subsystem, it should enable this
-feature by executing the pm_runtime_enable() helper function. However, the
-driver should not call the pm_runtime_allow() helper function unblocking
-the runtime PM of the device. Instead, it should allow user space or some
-platform-specific code to do that (user space can do it via sysfs), although
-once it has called pm_runtime_enable(), it must be prepared to handle the
+The runtime PM of PCI devices is enabled by default by the PCI core. PCI
+device drivers do not need to enable it and should not attempt to do so.
+However, it is blocked by pci_pm_init() that runs the pm_runtime_forbid()
+helper function. In addition to that, the runtime PM usage counter of
+each PCI device is incremented by local_pci_probe() before executing the
+probe callback provided by the device's driver.
+
+If a PCI driver implements the runtime PM callbacks and intends to use the
+runtime PM framework provided by the PM core and the PCI subsystem, it needs
+to decrement the device's runtime PM usage counter in its probe callback
+function. If it doesn't do that, the counter will always be different from
+zero for the device and it will never be runtime-suspended. The simplest
+way to do that is by calling pm_runtime_put_noidle(), but if the driver
+wants to schedule an autosuspend right away, for example, it may call
+pm_runtime_put_autosuspend() instead for this purpose. Generally, it
+just needs to call a function that decrements the devices usage counter
+from its probe routine to make runtime PM work for the device.
+
+It is important to remember that the driver's runtime_suspend() callback
+may be executed right after the usage counter has been decremented, because
+user space may already have cuased the pm_runtime_allow() helper function
+unblocking the runtime PM of the device to run via sysfs, so the driver must
+be prepared to cope with that.
+
+The driver itself should not call pm_runtime_allow(), though. Instead, it
+should let user space or some platform-specific code do that (user space can
+do it via sysfs as stated above), but it must be prepared to handle the
runtime PM of the device correctly as soon as pm_runtime_allow() is called
-(which may happen at any time). [It also is possible that user space causes
-pm_runtime_allow() to be called via sysfs before the driver is loaded, so in
-fact the driver has to be prepared to handle the runtime PM of the device as
-soon as it calls pm_runtime_enable().]
+(which may happen at any time, even before the driver is loaded).
+
+When the driver's remove callback runs, it has to balance the decrementation
+of the device's runtime PM usage counter at the probe time. For this reason,
+if it has decremented the counter in its probe callback, it must run
+pm_runtime_get_noresume() in its remove callback. [Since the core carries
+out a runtime resume of the device and bumps up the device's usage counter
+before running the driver's remove callback, the runtime PM of the device
+is effectively disabled for the duration of the remove execution and all
+runtime PM helper functions incrementing the device's usage counter are
+then effectively equivalent to pm_runtime_get_noresume().]
The runtime PM framework works by processing requests to suspend or resume
devices, or to check if they are idle (in which cases it is reasonable to
diff --git a/kernel/Documentation/power/runtime_pm.txt b/kernel/Documentation/power/runtime_pm.txt
index 44fe1d28a..0784bc3a2 100644
--- a/kernel/Documentation/power/runtime_pm.txt
+++ b/kernel/Documentation/power/runtime_pm.txt
@@ -445,10 +445,6 @@ drivers/base/power/runtime.c and include/linux/pm_runtime.h:
bool pm_runtime_status_suspended(struct device *dev);
- return true if the device's runtime PM status is 'suspended'
- bool pm_runtime_suspended_if_enabled(struct device *dev);
- - return true if the device's runtime PM status is 'suspended' and its
- 'power.disable_depth' field is equal to 1
-
void pm_runtime_allow(struct device *dev);
- set the power.runtime_auto flag for the device and decrease its usage
counter (used by the /sys/devices/.../power/control interface to
@@ -556,6 +552,12 @@ helper functions described in Section 4. In that case, pm_runtime_resume()
should be used. Of course, for this purpose the device's runtime PM has to be
enabled earlier by calling pm_runtime_enable().
+Note, if the device may execute pm_runtime calls during the probe (such as
+if it is registers with a subsystem that may call back in) then the
+pm_runtime_get_sync() call paired with a pm_runtime_put() call will be
+appropriate to ensure that the device is not put back to sleep during the
+probe. This can happen with systems such as the network device layer.
+
It may be desirable to suspend the device once ->probe() has finished.
Therefore the driver core uses the asyncronous pm_request_idle() to submit a
request to execute the subsystem-level idle callback for the device at that
diff --git a/kernel/Documentation/power/suspend-and-cpuhotplug.txt b/kernel/Documentation/power/suspend-and-cpuhotplug.txt
index 2850df3bf..2fc909502 100644
--- a/kernel/Documentation/power/suspend-and-cpuhotplug.txt
+++ b/kernel/Documentation/power/suspend-and-cpuhotplug.txt
@@ -72,7 +72,7 @@ More details follow:
|
v
Disable regular cpu hotplug
- by setting cpu_hotplug_disabled=1
+ by increasing cpu_hotplug_disabled
|
v
Release cpu_add_remove_lock
@@ -89,7 +89,7 @@ Resuming back is likewise, with the counterparts being (in the order of
execution during resume):
* enable_nonboot_cpus() which involves:
| Acquire cpu_add_remove_lock
- | Reset cpu_hotplug_disabled to 0, thereby enabling regular cpu hotplug
+ | Decrease cpu_hotplug_disabled, thereby enabling regular cpu hotplug
| Call _cpu_up() [for all those cpus in the frozen_cpus mask, in a loop]
| Release cpu_add_remove_lock
v
@@ -120,7 +120,7 @@ after the entire cycle is complete (i.e., suspend + resume).
Acquire cpu_add_remove_lock
|
v
- If cpu_hotplug_disabled is 1
+ If cpu_hotplug_disabled > 0
return gracefully
|
|
diff --git a/kernel/Documentation/power/swsusp.txt b/kernel/Documentation/power/swsusp.txt
index f732a8321..8cc17ca71 100644
--- a/kernel/Documentation/power/swsusp.txt
+++ b/kernel/Documentation/power/swsusp.txt
@@ -410,8 +410,17 @@ Documentation/usb/persist.txt.
Q: Can I suspend-to-disk using a swap partition under LVM?
-A: No. You can suspend successfully, but you'll not be able to
-resume. uswsusp should be able to work with LVM. See suspend.sf.net.
+A: Yes and No. You can suspend successfully, but the kernel will not be able
+to resume on its own. You need an initramfs that can recognize the resume
+situation, activate the logical volume containing the swap volume (but not
+touch any filesystems!), and eventually call
+
+echo -n "$major:$minor" > /sys/power/resume
+
+where $major and $minor are the respective major and minor device numbers of
+the swap volume.
+
+uswsusp works with LVM, too. See http://suspend.sourceforge.net/
Q: I upgraded the kernel from 2.6.15 to 2.6.16. Both kernels were
compiled with the similar configuration files. Anyway I found that