Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 107 insertions, 0 deletions

diff --git a/kernel/Documentation/networking/ipvlan.txt b/kernel/Documentation/networking/ipvlan.txt
new file mode 100644
index 000000000..cf996394e
--- /dev/null
+++ b/kernel/Documentation/networking/ipvlan.txt
@@ -0,0 +1,107 @@
+
+                            IPVLAN Driver HOWTO
+
+Initial Release:
+	Mahesh Bandewar <maheshb AT google.com>
+
+1. Introduction:
+	This is conceptually very similar to the macvlan driver with one major
+exception of using L3 for mux-ing /demux-ing among slaves. This property makes
+the master device share the L2 with it's slave devices. I have developed this
+driver in conjuntion with network namespaces and not sure if there is use case
+outside of it.
+
+
+2. Building and Installation:
+	In order to build the driver, please select the config item CONFIG_IPVLAN.
+The driver can be built into the kernel (CONFIG_IPVLAN=y) or as a module
+(CONFIG_IPVLAN=m).
+
+
+3. Configuration:
+	There are no module parameters for this driver and it can be configured
+using IProute2/ip utility.
+
+	ip link add link <master-dev> <slave-dev> type ipvlan mode { l2 | L3 }
+
+	e.g. ip link add link ipvl0 eth0 type ipvlan mode l2
+
+
+4. Operating modes:
+	IPvlan has two modes of operation - L2 and L3. For a given master device,
+you can select one of these two modes and all slaves on that master will
+operate in the same (selected) mode. The RX mode is almost identical except
+that in L3 mode the slaves wont receive any multicast / broadcast traffic.
+L3 mode is more restrictive since routing is controlled from the other (mostly)
+default namespace.
+
+4.1 L2 mode:
+	In this mode TX processing happens on the stack instance attached to the
+slave device and packets are switched and queued to the master device to send
+out. In this mode the slaves will RX/TX multicast and broadcast (if applicable)
+as well.
+
+4.2 L3 mode:
+	In this mode TX processing upto L3 happens on the stack instance attached
+to the slave device and packets are switched to the stack instance of the
+master device for the L2 processing and routing from that instance will be
+used before packets are queued on the outbound device. In this mode the slaves
+will not receive nor can send multicast / broadcast traffic.
+
+
+5. What to choose (macvlan vs. ipvlan)?
+	These two devices are very similar in many regards and the specific use
+case could very well define which device to choose. if one of the following
+situations defines your use case then you can choose to use ipvlan -
+	(a) The Linux host that is connected to the external switch / router has
+policy configured that allows only one mac per port.
+	(b) No of virtual devices created on a master exceed the mac capacity and
+puts the NIC in promiscous mode and degraded performance is a concern.
+	(c) If the slave device is to be put into the hostile / untrusted network
+namespace where L2 on the slave could be changed / misused.
+
+
+6. Example configuration:
+
+  +=============================================================+
+  |  Host: host1                                                |
+  |                                                             |
+  |   +----------------------+      +----------------------+    |
+  |   |   NS:ns0             |      |  NS:ns1              |    |
+  |   |                      |      |                      |    |
+  |   |                      |      |                      |    |
+  |   |        ipvl0         |      |         ipvl1        |    |
+  |   +----------#-----------+      +-----------#----------+    |
+  |              #                              #               |
+  |              ################################               |
+  |                              # eth0                         |
+  +==============================#==============================+
+
+
+	(a) Create two network namespaces - ns0, ns1
+		ip netns add ns0
+		ip netns add ns1
+
+	(b) Create two ipvlan slaves on eth0 (master device)
+		ip link add link eth0 ipvl0 type ipvlan mode l2
+		ip link add link eth0 ipvl1 type ipvlan mode l2
+
+	(c) Assign slaves to the respective network namespaces
+		ip link set dev ipvl0 netns ns0
+		ip link set dev ipvl1 netns ns1
+
+	(d) Now switch to the namespace (ns0 or ns1) to configure the slave devices
+		- For ns0
+			(1) ip netns exec ns0 bash
+			(2) ip link set dev ipvl0 up
+			(3) ip link set dev lo up
+			(4) ip -4 addr add 127.0.0.1 dev lo
+			(5) ip -4 addr add $IPADDR dev ipvl0
+			(6) ip -4 route add default via $ROUTER dev ipvl0
+		- For ns1
+			(1) ip netns exec ns1 bash
+			(2) ip link set dev ipvl1 up
+			(3) ip link set dev lo up
+			(4) ip -4 addr add 127.0.0.1 dev lo
+			(5) ip -4 addr add $IPADDR dev ipvl1
+			(6) ip -4 route add default via $ROUTER dev ipvl1