Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 39 insertions, 0 deletions

diff --git a/kernel/Documentation/networking/framerelay.txt b/kernel/Documentation/networking/framerelay.txt
new file mode 100644
index 000000000..1a0b72044
--- /dev/null
+++ b/kernel/Documentation/networking/framerelay.txt
@@ -0,0 +1,39 @@
+Frame Relay (FR) support for linux is built into a two tiered system of device 
+drivers.  The upper layer implements RFC1490 FR specification, and uses the
+Data Link Connection Identifier (DLCI) as its hardware address.  Usually these
+are assigned by your network supplier, they give you the number/numbers of
+the Virtual Connections (VC) assigned to you.
+
+Each DLCI is a point-to-point link between your machine and a remote one.
+As such, a separate device is needed to accommodate the routing.  Within the
+net-tools archives is 'dlcicfg'.  This program will communicate with the
+base "DLCI" device, and create new net devices named 'dlci00', 'dlci01'... 
+The configuration script will ask you how many DLCIs you need, as well as
+how many DLCIs you want to assign to each Frame Relay Access Device (FRAD).
+
+The DLCI uses a number of function calls to communicate with the FRAD, all
+of which are stored in the FRAD's private data area.  assoc/deassoc, 
+activate/deactivate and dlci_config.  The DLCI supplies a receive function
+to the FRAD to accept incoming packets.
+
+With this initial offering, only 1 FRAD driver is available.  With many thanks
+to Sangoma Technologies, David Mandelstam & Gene Kozin, the S502A, S502E & 
+S508 are supported.  This driver is currently set up for only FR, but as 
+Sangoma makes more firmware modules available, it can be updated to provide
+them as well.
+
+Configuration of the FRAD makes use of another net-tools program, 'fradcfg'.
+This program makes use of a configuration file (which dlcicfg can also read)
+to specify the types of boards to be configured as FRADs, as well as perform
+any board specific configuration.  The Sangoma module of fradcfg loads the
+FR firmware into the card, sets the irq/port/memory information, and provides
+an initial configuration.
+
+Additional FRAD device drivers can be added as hardware is available.
+
+At this time, the dlcicfg and fradcfg programs have not been incorporated into
+the net-tools distribution.  They can be found at ftp.invlogic.com, in 
+/pub/linux.  Note that with OS/2 FTPD, you end up in /pub by default, so just
+use 'cd linux'.  v0.10 is for use on pre-2.0.3 and earlier, v0.15 is for 
+pre-2.0.4 and later.
+