Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 461 insertions, 0 deletions

diff --git a/kernel/Documentation/networking/e1000.txt b/kernel/Documentation/networking/e1000.txt
new file mode 100644
index 000000000..437b2099c
--- /dev/null
+++ b/kernel/Documentation/networking/e1000.txt
@@ -0,0 +1,461 @@
+Linux* Base Driver for Intel(R) Ethernet Network Connection
+===========================================================
+
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2013 Intel Corporation.
+
+Contents
+========
+
+- Identifying Your Adapter
+- Command Line Parameters
+- Speed and Duplex Configuration
+- Additional Configurations
+- Support
+
+Identifying Your Adapter
+========================
+
+For more information on how to identify your adapter, go to the Adapter &
+Driver ID Guide at:
+
+    http://support.intel.com/support/go/network/adapter/idguide.htm
+
+For the latest Intel network drivers for Linux, refer to the following
+website.  In the search field, enter your adapter name or type, or use the
+networking link on the left to search for your adapter:
+
+    http://support.intel.com/support/go/network/adapter/home.htm
+
+Command Line Parameters
+=======================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+NOTES:  For more information about the AutoNeg, Duplex, and Speed
+        parameters, see the "Speed and Duplex Configuration" section in
+        this document.
+
+        For more information about the InterruptThrottleRate,
+        RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+        parameters, see the application note at:
+        http://www.intel.com/design/network/applnots/ap450.htm
+
+AutoNeg
+-------
+(Supported only on adapters with copper connections)
+Valid Range:   0x01-0x0F, 0x20-0x2F
+Default Value: 0x2F
+
+This parameter is a bit-mask that specifies the speed and duplex settings
+advertised by the adapter.  When this parameter is used, the Speed and
+Duplex parameters must not be specified.
+
+NOTE:  Refer to the Speed and Duplex section of this readme for more
+       information on the AutoNeg parameter.
+
+Duplex
+------
+(Supported only on adapters with copper connections)
+Valid Range:   0-2 (0=auto-negotiate, 1=half, 2=full)
+Default Value: 0
+
+This defines the direction in which data is allowed to flow.  Can be
+either one or two-directional.  If both Duplex and the link partner are
+set to auto-negotiate, the board auto-detects the correct duplex.  If the
+link partner is forced (either full or half), Duplex defaults to half-
+duplex.
+
+FlowControl
+-----------
+Valid Range:   0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
+Default Value: Reads flow control settings from the EEPROM
+
+This parameter controls the automatic generation(Tx) and response(Rx)
+to Ethernet PAUSE frames.
+
+InterruptThrottleRate
+---------------------
+(not supported on Intel(R) 82542, 82543 or 82544-based adapters)
+Valid Range:   0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+                                 4=simplified balancing)
+Default Value: 3
+
+The driver can limit the amount of interrupts per second that the adapter
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
+will generate per second.
+
+Setting InterruptThrottleRate to a value greater or equal to 100
+will program the adapter to send out a maximum of that many interrupts
+per second, even if more packets have come in. This reduces interrupt
+load on the system and can lower CPU utilization under heavy load,
+but will increase latency as packets are not processed as quickly.
+
+The default behaviour of the driver previously assumed a static
+InterruptThrottleRate value of 8000, providing a good fallback value for
+all traffic types,but lacking in small packet performance and latency.
+The hardware can handle many more small packets per second however, and
+for this reason an adaptive interrupt moderation algorithm was implemented.
+
+Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
+that it receives. After determining the type of incoming traffic in the last
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+for that traffic.
+
+The algorithm classifies the incoming traffic every interval into
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
+"Bulk traffic", for large amounts of packets of normal size; "Low latency",
+for small amounts of traffic and/or a significant percentage of small
+packets; and "Lowest latency", for almost completely small packets or
+minimal traffic.
+
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
+stepwise to 20000. This default mode is suitable for most applications.
+
+For situations where low latency is vital such as cluster or
+grid computing, the algorithm can reduce latency even more when
+InterruptThrottleRate is set to mode 1. In this mode, which operates
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
+70000 for traffic in class "Lowest latency".
+
+In simplified mode the interrupt rate is based on the ratio of TX and
+RX traffic.  If the bytes per second rate is approximately equal, the
+interrupt rate will drop as low as 2000 interrupts per second.  If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
+Setting InterruptThrottleRate to 0 turns off any interrupt moderation
+and may improve small packet latency, but is generally not suitable
+for bulk throughput traffic.
+
+NOTE:  InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+       RxAbsIntDelay parameters.  In other words, minimizing the receive
+       and/or transmit absolute delays does not force the controller to
+       generate more interrupts than what the Interrupt Throttle Rate
+       allows.
+
+CAUTION:  If you are using the Intel(R) PRO/1000 CT Network Connection
+          (controller 82547), setting InterruptThrottleRate to a value
+          greater than 75,000, may hang (stop transmitting) adapters
+          under certain network conditions.  If this occurs a NETDEV
+          WATCHDOG message is logged in the system event log.  In
+          addition, the controller is automatically reset, restoring
+          the network connection.  To eliminate the potential for the
+          hang, ensure that InterruptThrottleRate is set no greater
+          than 75,000 and is not set to 0.
+
+NOTE:  When e1000 is loaded with default settings and multiple adapters
+       are in use simultaneously, the CPU utilization may increase non-
+       linearly.  In order to limit the CPU utilization without impacting
+       the overall throughput, we recommend that you load the driver as
+       follows:
+
+           modprobe e1000 InterruptThrottleRate=3000,3000,3000
+
+       This sets the InterruptThrottleRate to 3000 interrupts/sec for
+       the first, second, and third instances of the driver.  The range
+       of 2000 to 3000 interrupts per second works on a majority of
+       systems and is a good starting point, but the optimal value will
+       be platform-specific.  If CPU utilization is not a concern, use
+       RX_POLLING (NAPI) and default driver settings.
+
+RxDescriptors
+-------------
+Valid Range:   80-256 for 82542 and 82543-based adapters
+               80-4096 for all other supported adapters
+Default Value: 256
+
+This value specifies the number of receive buffer descriptors allocated
+by the driver.  Increasing this value allows the driver to buffer more
+incoming packets, at the expense of increased system memory utilization.
+
+Each descriptor is 16 bytes.  A receive buffer is also allocated for each
+descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
+on the MTU setting. The maximum MTU size is 16110.
+
+NOTE:  MTU designates the frame size.  It only needs to be set for Jumbo
+       Frames.  Depending on the available system resources, the request
+       for a higher number of receive descriptors may be denied.  In this
+       case, use a lower number.
+
+RxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 0
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds.  Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic.  Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic.  If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION:  When setting RxIntDelay to a value other than 0, adapters may
+          hang (stop transmitting) under certain network conditions.  If
+          this occurs a NETDEV WATCHDOG message is logged in the system
+          event log.  In addition, the controller is automatically reset,
+          restoring the network connection.  To eliminate the potential
+          for the hang ensure that RxIntDelay is set to 0.
+
+RxAbsIntDelay
+-------------
+(This parameter is supported only on 82540, 82545 and later adapters.)
+Valid Range:   0-65535 (0=off)
+Default Value: 128
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated.  Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time.  Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+Speed
+-----
+(This parameter is supported only on adapters with copper connections.)
+Valid Settings: 0, 10, 100, 1000
+Default Value:  0 (auto-negotiate at all supported speeds)
+
+Speed forces the line speed to the specified value in megabits per second
+(Mbps).  If this parameter is not specified or is set to 0 and the link
+partner is set to auto-negotiate, the board will auto-detect the correct
+speed.  Duplex should also be set when Speed is set to either 10 or 100.
+
+TxDescriptors
+-------------
+Valid Range:   80-256 for 82542 and 82543-based adapters
+               80-4096 for all other supported adapters
+Default Value: 256
+
+This value is the number of transmit descriptors allocated by the driver.
+Increasing this value allows the driver to queue more transmits.  Each
+descriptor is 16 bytes.
+
+NOTE:  Depending on the available system resources, the request for a
+       higher number of transmit descriptors may be denied.  In this case,
+       use a lower number.
+
+TxDescriptorStep
+----------------
+Valid Range:    1 (use every Tx Descriptor)
+                4 (use every 4th Tx Descriptor)
+
+Default Value:  1 (use every Tx Descriptor)
+
+On certain non-Intel architectures, it has been observed that intense TX
+traffic bursts of short packets may result in an improper descriptor
+writeback. If this occurs, the driver will report a "TX Timeout" and reset
+the adapter, after which the transmit flow will restart, though data may
+have stalled for as much as 10 seconds before it resumes.
+
+The improper writeback does not occur on the first descriptor in a system
+memory cache-line, which is typically 32 bytes, or 4 descriptors long.
+
+Setting TxDescriptorStep to a value of 4 will ensure that all TX descriptors
+are aligned to the start of a system memory cache line, and so this problem
+will not occur.
+
+NOTES: Setting TxDescriptorStep to 4 effectively reduces the number of
+       TxDescriptors available for transmits to 1/4 of the normal allocation.
+       This has a possible negative performance impact, which may be
+       compensated for by allocating more descriptors using the TxDescriptors
+       module parameter.
+
+       There are other conditions which may result in "TX Timeout", which will
+       not be resolved by the use of the TxDescriptorStep parameter. As the
+       issue addressed by this parameter has never been observed on Intel
+       Architecture platforms, it should not be used on Intel platforms.
+
+TxIntDelay
+----------
+Valid Range:   0-65535 (0=off)
+Default Value: 64
+
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds.  Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic.  If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+TxAbsIntDelay
+-------------
+(This parameter is supported only on 82540, 82545 and later adapters.)
+Valid Range:   0-65535 (0=off)
+Default Value: 64
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated.  Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time.  Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+XsumRX
+------
+(This parameter is NOT supported on the 82542-based adapter.)
+Valid Range:   0-1
+Default Value: 1
+
+A value of '1' indicates that the driver should enable IP checksum
+offload for received packets (both UDP and TCP) to the adapter hardware.
+
+Copybreak
+---------
+Valid Range:   0-xxxxxxx (0=off)
+Default Value: 256
+Usage: insmod e1000.ko copybreak=128
+
+Driver copies all packets below or equaling this size to a fresh RX
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value:  0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can turn off
+this parameter in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
+
+Speed and Duplex Configuration
+==============================
+
+Three keywords are used to control the speed and duplex configuration.
+These keywords are Speed, Duplex, and AutoNeg.
+
+If the board uses a fiber interface, these keywords are ignored, and the
+fiber interface board only links at 1000 Mbps full-duplex.
+
+For copper-based boards, the keywords interact as follows:
+
+  The default operation is auto-negotiate.  The board advertises all
+  supported speed and duplex combinations, and it links at the highest
+  common speed and duplex mode IF the link partner is set to auto-negotiate.
+
+  If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
+  is advertised (The 1000BaseT spec requires auto-negotiation.)
+
+  If Speed = 10 or 100, then both Speed and Duplex should be set.  Auto-
+  negotiation is disabled, and the AutoNeg parameter is ignored.  Partner
+  SHOULD also be forced.
+
+The AutoNeg parameter is used when more control is required over the
+auto-negotiation process.  It should be used when you wish to control which
+speed and duplex combinations are advertised during the auto-negotiation
+process.
+
+The parameter may be specified as either a decimal or hexadecimal value as
+determined by the bitmap below.
+
+Bit position   7      6      5       4       3      2      1       0
+Decimal Value  128    64     32      16      8      4      2       1
+Hex value      80     40     20      10      8      4      2       1
+Speed (Mbps)   N/A    N/A    1000    N/A     100    100    10      10
+Duplex                       Full            Full   Half   Full    Half
+
+Some examples of using AutoNeg:
+
+  modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
+  modprobe e1000 AutoNeg=1 (Same as above)
+  modprobe e1000 AutoNeg=0x02 (Restricts autonegotiation to 10 Full)
+  modprobe e1000 AutoNeg=0x03 (Restricts autonegotiation to 10 Half or 10 Full)
+  modprobe e1000 AutoNeg=0x04 (Restricts autonegotiation to 100 Half)
+  modprobe e1000 AutoNeg=0x05 (Restricts autonegotiation to 10 Half or 100
+  Half)
+  modprobe e1000 AutoNeg=0x020 (Restricts autonegotiation to 1000 Full)
+  modprobe e1000 AutoNeg=32 (Same as above)
+
+Note that when this parameter is used, Speed and Duplex must not be specified.
+
+If the link partner is forced to a specific speed and duplex, then this
+parameter should not be used.  Instead, use the Speed and Duplex parameters
+previously mentioned to force the adapter to the same speed and duplex.
+
+Additional Configurations
+=========================
+
+  Jumbo Frames
+  ------------
+  Jumbo Frames support is enabled by changing the MTU to a value larger than
+  the default of 1500.  Use the ifconfig command to increase the MTU size.
+  For example:
+
+       ifconfig eth<x> mtu 9000 up
+
+  This setting is not saved across reboots.  It can be made permanent if
+  you add:
+
+       MTU=9000
+
+   to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
+   applies to the Red Hat distributions; other distributions may store this
+   setting in a different location.
+
+  Notes:
+  Degradation in throughput performance may be observed in some Jumbo frames
+  environments. If this is observed, increasing the application's socket buffer
+  size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
+  See the specific application manual and /usr/src/linux*/Documentation/
+  networking/ip-sysctl.txt for more details.
+
+  - The maximum MTU setting for Jumbo Frames is 16110.  This value coincides
+    with the maximum Jumbo Frames size of 16128.
+
+  - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
+    poor performance or loss of link.
+
+  - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
+    support Jumbo Frames. These correspond to the following product names:
+     Intel(R) PRO/1000 Gigabit Server Adapter
+     Intel(R) PRO/1000 PM Network Connection
+
+  ethtool
+  -------
+  The driver utilizes the ethtool interface for driver configuration and
+  diagnostics, as well as displaying statistical information.  The ethtool
+  version 1.6 or later is required for this functionality.
+
+  The latest release of ethtool can be found from
+  http://ftp.kernel.org/pub/software/network/ethtool/
+
+  Enabling Wake on LAN* (WoL)
+  ---------------------------
+  WoL is configured through the ethtool* utility.
+
+  WoL will be enabled on the system during the next shut down or reboot.
+  For this driver version, in order to enable WoL, the e1000 driver must be
+  loaded when shutting down or rebooting the system.
+
+Support
+=======
+
+For general information, go to the Intel support website at:
+
+    http://support.intel.com
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+
+    http://sourceforge.net/projects/e1000
+
+If an issue is identified with the released source code on the supported
+kernel with a supported adapter, email the specific information related
+to the issue to e1000-devel@lists.sf.net