Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 74 insertions, 0 deletions

diff --git a/kernel/Documentation/hwmon/sht15 b/kernel/Documentation/hwmon/sht15
new file mode 100644
index 000000000..778987d18
--- /dev/null
+++ b/kernel/Documentation/hwmon/sht15
@@ -0,0 +1,74 @@
+Kernel driver sht15
+===================
+
+Authors:
+  * Wouter Horre
+  * Jonathan Cameron
+  * Vivien Didelot <vivien.didelot@savoirfairelinux.com>
+  * Jerome Oufella <jerome.oufella@savoirfairelinux.com>
+
+Supported chips:
+  * Sensirion SHT10
+    Prefix: 'sht10'
+
+  * Sensirion SHT11
+    Prefix: 'sht11'
+
+  * Sensirion SHT15
+    Prefix: 'sht15'
+
+  * Sensirion SHT71
+    Prefix: 'sht71'
+
+  * Sensirion SHT75
+    Prefix: 'sht75'
+
+Datasheet: Publicly available at the Sensirion website
+http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
+
+Description
+-----------
+
+The SHT10, SHT11, SHT15, SHT71, and SHT75 are humidity and temperature
+sensors.
+
+The devices communicate using two GPIO lines.
+
+Supported resolutions for the measurements are 14 bits for temperature and 12
+bits for humidity, or 12 bits for temperature and 8 bits for humidity.
+
+The humidity calibration coefficients are programmed into an OTP memory on the
+chip. These coefficients are used to internally calibrate the signals from the
+sensors. Disabling the reload of those coefficients allows saving 10ms for each
+measurement and decrease power consumption, while losing on precision.
+
+Some options may be set directly in the sht15_platform_data structure
+or via sysfs attributes.
+
+Notes:
+  * The regulator supply name is set to "vcc".
+  * If a CRC validation fails, a soft reset command is sent, which resets
+    status register to its hardware default value, but the driver will try to
+    restore the previous device configuration.
+
+Platform data
+-------------
+
+* checksum:
+  set it to true to enable CRC validation of the readings (default to false).
+* no_otp_reload:
+  flag to indicate not to reload from OTP (default to false).
+* low_resolution:
+  flag to indicate the temp/humidity resolution to use (default to false).
+
+Sysfs interface
+---------------
+
+* temp1_input:     temperature input
+* humidity1_input: humidity input
+* heater_enable:   write 1 in this attribute to enable the on-chip heater,
+                   0 to disable it. Be careful not to enable the heater
+                   for too long.
+* temp1_fault:     if 1, this means that the voltage is low (below 2.47V) and
+                   measurement may be invalid.
+* humidity1_fault: same as temp1_fault.