These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

7 files changed, 147 insertions, 4 deletions

diff --git a/kernel/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
new file mode 100644
index 000000000..f7cc7c060
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt
@@ -0,0 +1,35 @@
+* Atmel SAMA5D4 Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible: "atmel,sama5d4-wdt"
+- reg: base physical address and length of memory mapped region.
+
+Optional properties:
+- timeout-sec: watchdog timeout value (in seconds).
+- interrupts: interrupt number to the CPU.
+- atmel,watchdog-type: should be "hardware" or "software".
+	"hardware": enable watchdog fault reset. A watchdog fault triggers
+		    watchdog reset.
+	"software": enable watchdog fault interrupt. A watchdog fault asserts
+		    watchdog interrupt.
+- atmel,idle-halt: present if you want to stop the watchdog when the CPU is
+		   in idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
+- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is
+		  in debug state.
+
+Example:
+	watchdog@fc068640 {
+		compatible = "atmel,sama5d4-wdt";
+		reg = <0xfc068640 0x10>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH 5>;
+		timeout-sec = <10>;
+		atmel,watchdog-type = "hardware";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+		status = "okay";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
index a4d869744..86fa6de10 100644
--- a/kernel/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
+++ b/kernel/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
@@ -6,6 +6,7 @@ Required properties:
 - compatible: must be "atmel,at91sam9260-wdt".
 - reg: physical base address of the controller and length of memory mapped
   region.
+- clocks: phandle to input clock.
 
 Optional properties:
 - timeout-sec: contains the watchdog timeout in seconds.
@@ -39,6 +40,7 @@ Example:
 		compatible = "atmel,at91sam9260-wdt";
 		reg = <0xfffffd40 0x10>;
 		interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+		clocks = <&clk32k>;
 		timeout-sec = <15>;
 		atmel,watchdog-type = "hardware";
 		atmel,reset-type = "all";
diff --git a/kernel/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt
new file mode 100644
index 000000000..84122270b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/watchdog/brcm,bcm7038-wdt.txt
@@ -0,0 +1,19 @@
+BCM7038 Watchdog timer
+
+Required properties:
+
+- compatible : should be "brcm,bcm7038-wdt"
+- reg : Specifies base physical address and size of the registers.
+
+Optional properties:
+
+- clocks: The clock running the watchdog. If no clock is found the
+	  driver will default to 27000000 Hz.
+
+Example:
+
+watchdog@f040a7e8 {
+	compatible = "brcm,bcm7038-wdt";
+	clocks = <&upg_fixed>;
+	reg = <0xf040a7e8 0x16>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/watchdog/digicolor-wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/digicolor-wdt.txt
new file mode 100644
index 000000000..a882967e1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/watchdog/digicolor-wdt.txt
@@ -0,0 +1,25 @@
+Conexant Digicolor SoCs Watchdog timer
+
+The watchdog functionality in Conexant Digicolor SoCs relies on the so called
+"Agent Communication" block. This block includes the eight programmable system
+timer counters. The first timer (called "Timer A") is the only one that can be
+used as watchdog.
+
+Required properties:
+
+- compatible : Should be "cnxt,cx92755-wdt"
+- reg : Specifies base physical address and size of the registers
+- clocks : phandle; specifies the clock that drives the timer
+
+Optional properties:
+
+- timeout-sec : Contains the watchdog timeout in seconds
+
+Example:
+
+	watchdog@f0000fc0 {
+		compatible = "cnxt,cx92755-wdt";
+		reg = <0xf0000fc0 0x8>;
+		clocks = <&main_clk>;
+		timeout-sec = <15>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt
new file mode 100644
index 000000000..09f6b2496
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt
@@ -0,0 +1,19 @@
+* NXP LPC18xx Watchdog Timer (WDT)
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-wwdt"
+- reg: Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdtclk" and "reg"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts: Should contain WDT interrupt
+
+Examples:
+
+watchdog@40080000 {
+	compatible = "nxp,lpc1850-wwdt";
+	reg = <0x40080000 0x24>;
+	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
+	clock-names = "wdtclk", "reg";
+	interrupts = <49>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/watchdog/omap-wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/omap-wdt.txt
index c22797067..1fa20e453 100644
--- a/kernel/Documentation/devicetree/bindings/watchdog/omap-wdt.txt
+++ b/kernel/Documentation/devicetree/bindings/watchdog/omap-wdt.txt
@@ -1,10 +1,11 @@
 TI Watchdog Timer (WDT) Controller for OMAP
 
 Required properties:
-compatible:
-- "ti,omap3-wdt" for OMAP3
-- "ti,omap4-wdt" for OMAP4
-- ti,hwmods: Name of the hwmod associated to the WDT
+- compatible : "ti,omap3-wdt" for OMAP3 or "ti,omap4-wdt" for OMAP4
+- ti,hwmods : Name of the hwmod associated to the WDT
+
+Optional properties:
+- timeout-sec : default watchdog timeout in seconds
 
 Examples:
 
diff --git a/kernel/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt b/kernel/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt
new file mode 100644
index 000000000..039c5ca45
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt
@@ -0,0 +1,42 @@
+STMicroelectronics Low Power Controller (LPC) - Watchdog
+========================================================
+
+LPC currently supports Watchdog OR Real Time Clock OR Clocksource
+functionality.
+
+[See: ../rtc/rtc-st-lpc.txt for RTC options]
+[See: ../timer/st,stih407-lpc for Clocksource options]
+
+Required properties
+
+- compatible 	: Must be one of: "st,stih407-lpc" "st,stih416-lpc"
+				  "st,stih415-lpc" "st,stid127-lpc"
+- reg		: LPC registers base address + size
+- interrupts    : LPC interrupt line number and associated flags
+- clocks	: Clock used by LPC device (See: ../clock/clock-bindings.txt)
+- st,lpc-mode	: The LPC can run either one of three modes:
+                  ST_LPC_MODE_RTC    [0]
+                  ST_LPC_MODE_WDT    [1]
+                  ST_LPC_MODE_CLKSRC [2]
+		 One (and only one) mode must be selected.
+
+Required properties [watchdog mode]
+
+- st,syscfg	: Phandle to syscfg node used to enable watchdog and configure
+		  CPU reset type.
+- timeout-sec	: Watchdog timeout in seconds
+
+Optional properties [watchdog mode]
+
+- st,warm-reset	: If present reset type will be 'warm' - if not it will be cold
+
+Example:
+	lpc@fde05000 {
+		compatible	= "st,stih407-lpc";
+		reg		= <0xfde05000 0x1000>;
+		clocks 		= <&clk_s_d3_flexgen CLK_LPC_0>;
+		st,syscfg	= <&syscfg_core>;
+		timeout-sec	= <120>;
+		st,lpc-mode	= <ST_LPC_MODE_WDT>;
+		st,warm-reset;
+	};