These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 0 insertions, 110 deletions

diff --git a/kernel/Documentation/devicetree/bindings/video/samsung-fimd.txt b/kernel/Documentation/devicetree/bindings/video/samsung-fimd.txt
deleted file mode 100644
index a8bbbde03..000000000
--- a/kernel/Documentation/devicetree/bindings/video/samsung-fimd.txt
+++ /dev/null
@@ -1,110 +0,0 @@
-Device-Tree bindings for Samsung SoC display controller (FIMD)
-
-FIMD (Fully Interactive Mobile Display) is the Display Controller for the
-Samsung series of SoCs which transfers the image data from a video memory
-buffer to an external LCD interface.
-
-Required properties:
-- compatible: value should be one of the following
-		"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
-		"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
-		"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
-		"samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
-		"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
-		"samsung,exynos4415-fimd"; /* for Exynos4415 SoC */
-		"samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
-
-- reg: physical base address and length of the FIMD registers set.
-
-- interrupt-parent: should be the phandle of the fimd controller's
-		parent interrupt controller.
-
-- interrupts: should contain a list of all FIMD IP block interrupts in the
-		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
-		 format depends on the interrupt controller used.
-
-- interrupt-names: should contain the interrupt names: "fifo", "vsync",
-	"lcd_sys", in the same order as they were listed in the interrupts
-        property.
-
-- pinctrl-0: pin control group to be used for this controller.
-
-- pinctrl-names: must contain a "default" entry.
-
-- clocks: must include clock specifiers corresponding to entries in the
-         clock-names property.
-
-- clock-names: list of clock names sorted in the same order as the clocks
-               property. Must contain "sclk_fimd" and "fimd".
-
-Optional Properties:
-- power-domains: a phandle to FIMD power domain node.
-- samsung,invert-vden: video enable signal is inverted
-- samsung,invert-vclk: video clock signal is inverted
-- display-timings: timing settings for FIMD, as described in document [1].
-		Can be used in case timings cannot be provided otherwise
-		or to override timings provided by the panel.
-- samsung,sysreg: handle to syscon used to control the system registers
-- i80-if-timings: timing configuration for lcd i80 interface support.
-  - cs-setup: clock cycles for the active period of address signal is enabled
-              until chip select is enabled.
-              If not specified, the default value(0) will be used.
-  - wr-setup: clock cycles for the active period of CS signal is enabled until
-              write signal is enabled.
-              If not specified, the default value(0) will be used.
-  - wr-active: clock cycles for the active period of CS is enabled.
-               If not specified, the default value(1) will be used.
-  - wr-hold: clock cycles for the active period of CS is disabled until write
-             signal is disabled.
-             If not specified, the default value(0) will be used.
-
-  The parameters are defined as:
-
-    VCLK(internal)  __|??????|_____|??????|_____|??????|_____|??????|_____|??
-                      :            :            :            :            :
-    Address Output  --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
-                      | cs-setup+1 |            :            :            :
-                      |<---------->|            :            :            :
-    Chip Select     ???????????????|____________:____________:____________|??
-                                   | wr-setup+1 |            | wr-hold+1  |
-                                   |<---------->|            |<---------->|
-    Write Enable    ????????????????????????????|____________|???????????????
-                                                | wr-active+1|
-                                                |<---------->|
-    Video Data      ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
-
-The device node can contain 'port' child nodes according to the bindings defined
-in [2]. The following are properties specific to those nodes:
-- reg: (required) port index, can be:
-		0 - for CAMIF0 input,
-		1 - for CAMIF1 input,
-		2 - for CAMIF2 input,
-		3 - for parallel output,
-		4 - for write-back interface
-
-[1]: Documentation/devicetree/bindings/video/display-timing.txt
-[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-
-SoC specific DT entry:
-
-	fimd@11c00000 {
-		compatible = "samsung,exynos4210-fimd";
-		interrupt-parent = <&combiner>;
-		reg = <0x11c00000 0x20000>;
-		interrupt-names = "fifo", "vsync", "lcd_sys";
-		interrupts = <11 0>, <11 1>, <11 2>;
-		clocks = <&clock 140>, <&clock 283>;
-		clock-names = "sclk_fimd", "fimd";
-		power-domains = <&pd_lcd0>;
-		status = "disabled";
-	};
-
-Board specific DT entry:
-
-	fimd@11c00000 {
-		pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
-		pinctrl-names = "default";
-		status = "okay";
-	};