These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 0 insertions, 89 deletions

diff --git a/kernel/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/kernel/Documentation/devicetree/bindings/video/atmel,lcdc.txt
deleted file mode 100644
index ecb8da063..000000000
--- a/kernel/Documentation/devicetree/bindings/video/atmel,lcdc.txt
+++ /dev/null
@@ -1,89 +0,0 @@
-Atmel LCDC Framebuffer
------------------------------------------------------
-
-Required properties:
-- compatible :
-	"atmel,at91sam9261-lcdc" , 
-	"atmel,at91sam9263-lcdc" ,
-	"atmel,at91sam9g10-lcdc" ,
-	"atmel,at91sam9g45-lcdc" ,
-	"atmel,at91sam9g45es-lcdc" ,
-	"atmel,at91sam9rl-lcdc" ,
-	"atmel,at32ap-lcdc"
-- reg : Should contain 1 register ranges(address and length).
-	Can contain an additional register range(address and length)
-	for fixed framebuffer memory. Useful for dedicated memories.
-- interrupts : framebuffer controller interrupt
-- display: a phandle pointing to the display node
-
-Required nodes:
-- display: a display node is required to initialize the lcd panel
-	This should be in the board dts.
-- default-mode: a videomode within the display with timing parameters
-	as specified below.
-
-Optional properties:
-- lcd-supply: Regulator for LCD supply voltage.
-
-Example:
-
-	fb0: fb@0x00500000 {
-		compatible = "atmel,at91sam9g45-lcdc";
-		reg = <0x00500000 0x1000>;
-		interrupts = <23 3 0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_fb>;
-		display = <&display0>;
-		status = "okay";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-	};
-
-Example for fixed framebuffer memory:
-
-	fb0: fb@0x00500000 {
-		compatible = "atmel,at91sam9263-lcdc";
-		reg = <0x00700000 0x1000 0x70000000 0x200000>;
-		[...]
-	};
-
-Atmel LCDC Display
------------------------------------------------------
-Required properties (as per of_videomode_helper):
-
- - atmel,dmacon: dma controller configuration
- - atmel,lcdcon2: lcd controller configuration
- - atmel,guard-time: lcd guard time (Delay in frame periods)
- - bits-per-pixel: lcd panel bit-depth.
-
-Optional properties (as per of_videomode_helper):
- - atmel,lcdcon-backlight: enable backlight
- - atmel,lcdcon-backlight-inverted: invert backlight PWM polarity
- - atmel,lcd-wiring-mode: lcd wiring mode "RGB" or "BRG"
- - atmel,power-control-gpio: gpio to power on or off the LCD (as many as needed)
-
-Example:
-	display0: display {
-		bits-per-pixel = <32>;
-		atmel,lcdcon-backlight;
-		atmel,dmacon = <0x1>;
-		atmel,lcdcon2 = <0x80008002>;
-		atmel,guard-time = <9>;
-		atmel,lcd-wiring-mode = <1>;
-
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: timing0 {
-				clock-frequency = <9000000>;
-				hactive = <480>;
-				vactive = <272>;
-				hback-porch = <1>;
-				hfront-porch = <1>;
-				vback-porch = <40>;
-				vfront-porch = <1>;
-				hsync-len = <45>;
-				vsync-len = <1>;
-			};
-		};
-	};