These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 57 insertions, 1 deletions

diff --git a/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
index 27f8b1e5e..781296bfb 100644
--- a/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
+++ b/kernel/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
@@ -1,15 +1,64 @@
 * USB2 ChipIdea USB controller for ci13xxx
 
 Required properties:
-- compatible: should be "chipidea,usb2"
+- compatible: should be one of:
+	"fsl,imx27-usb"
+	"lsi,zevio-usb"
+	"qcom,ci-hdrc"
+	"chipidea,usb2"
+	"xlnx,zynq-usb-2.20a"
 - reg: base address and length of the registers
 - interrupts: interrupt for the USB controller
 
+Recommended properies:
+- phy_type: the type of the phy connected to the core. Should be one
+  of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this
+  property the PORTSC register won't be touched.
+- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg"
+
+Deprecated properties:
+- usb-phy:      phandle for the PHY device. Use "phys" instead.
+- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead.
+
 Optional properties:
 - clocks: reference to the USB clock
 - phys: reference to the USB PHY
 - phy-names: should be "usb-phy"
 - vbus-supply: reference to the VBUS regulator
+- maximum-speed: limit the maximum connection speed to "full-speed".
+- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts
+- itc-setting: interrupt threshold control register control, the setting
+  should be aligned with ITC bits at register USBCMD.
+- ahb-burst-config: it is vendor dependent, the required value should be
+  aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This
+  property is used to change AHB burst configuration, check the chipidea
+  spec for meaning of each value. If this property is not existed, it
+  will use the reset value.
+- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword
+  (4 bytes), This register represents the maximum length of a the burst
+  in 32-bit words while moving data from system memory to the USB
+  bus, the value of this property will only take effect if property
+  "ahb-burst-config" is set to 0, if this property is missing the reset
+  default of the hardware implementation will be used.
+- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword
+  (4 bytes), This register represents the maximum length of a the burst
+  in 32-bit words while moving data from the USB bus to system memory,
+  the value of this property will only take effect if property
+  "ahb-burst-config" is set to 0, if this property is missing the reset
+  default of the hardware implementation will be used.
+- extcon: phandles to external connector devices. First phandle should point to
+  external connector, which provide "USB" cable events, the second should point
+  to external connector device, which provide "USB-HOST" cable events. If one
+  of the external connector devices is not required, empty <0> phandle should
+  be specified.
+- phy-clkgate-delay-us: the delay time (us) between putting the PHY into
+  low power mode and gating the PHY clock.
+
+i.mx specific properties
+- fsl,usbmisc: phandler of non-core register device, with one
+  argument that indicate usb controller index
+- disable-over-current: disable over current detect
+- external-vbus-divider: enables off-chip resistor divider for Vbus
 
 Example:
 
@@ -21,4 +70,11 @@ Example:
 		phys = <&usb_phy0>;
 		phy-names = "usb-phy";
 		vbus-supply = <&reg_usb0_vbus>;
+		gadget-itc-setting = <0x4>; /* 4 micro-frames */
+		 /* Incremental burst of unspecified length */
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>; /* 64 bytes */
+		rx-burst-size-dword = <0x10>;
+		extcon = <0>, <&usb_id>;
+		phy-clkgate-delay-us = <400>;
 	};