Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

132 files changed, 5224 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt
new file mode 100644
index 000000000..547a49b56
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/adi,adau1701.txt
@@ -0,0 +1,35 @@
+Analog Devices ADAU1701
+
+Required properties:
+
+ - compatible:		Should contain "adi,adau1701"
+ - reg:			The i2c address. Value depends on the state of ADDR0
+			and ADDR1, as wired in hardware.
+
+Optional properties:
+
+ - reset-gpio: 		A GPIO spec to define which pin is connected to the
+			chip's !RESET pin. If specified, the driver will
+			assert a hardware reset at probe time.
+ - adi,pll-mode-gpios:	An array of two GPIO specs to describe the GPIOs
+			the ADAU's PLL config pins are connected to.
+			The state of the pins are set according to the
+			configured clock divider on ASoC side before the
+			firmware is loaded.
+ - adi,pin-config:	An array of 12 numerical values selecting one of the
+			pin configurations as described in the datasheet,
+			table 53. Note that the value of this property has
+			to be prefixed with '/bits/ 8'.
+
+Examples:
+
+	i2c_bus {
+		adau1701@34 {
+			compatible = "adi,adau1701";
+			reg = <0x34>;
+			reset-gpio = <&gpio 23 0>;
+			adi,pll-mode-gpios = <&gpio 24 0 &gpio 25 0>;
+			adi,pin-config = /bits/ 8 <0x4 0x7 0x5 0x5 0x4 0x4
+                                                   0x4 0x4 0x4 0x4 0x4 0x4>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt
new file mode 100644
index 000000000..5875ca459
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt
@@ -0,0 +1,31 @@
+ADI AXI-I2S controller
+
+Required properties:
+ - compatible : Must be "adi,axi-i2s-1.00.a"
+ - reg : Must contain I2S core's registers location and length
+ - clocks : Pairs of phandle and specifier referencing the controller's clocks.
+   The controller expects two clocks, the clock used for the AXI interface and
+   the clock used as the sampling rate reference clock sample.
+ - clock-names : "axi" for the clock to the AXI interface, "ref" for the sample
+   rate reference clock.
+ - dmas: Pairs of phandle and specifier for the DMA channels that are used by
+   the core. The core expects two dma channels, one for transmit and one for
+   receive.
+ - dma-names : "tx" for the transmit channel, "rx" for the receive channel.
+
+For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties
+please check:
+	* resource-names.txt
+	* clock/clock-bindings.txt
+	* dma/dma.txt
+
+Example:
+
+	i2s: i2s@0x77600000 {
+		compatible = "adi,axi-i2s-1.00.a";
+		reg = <0x77600000 0x1000>;
+		clocks = <&clk 15>, <&audio_clock>;
+		clock-names = "axi", "ref";
+		dmas = <&ps7_dma 0>, <&ps7_dma 1>;
+		dma-names = "tx", "rx";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt b/kernel/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt
new file mode 100644
index 000000000..4eb799767
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt
@@ -0,0 +1,30 @@
+ADI AXI-SPDIF controller
+
+Required properties:
+ - compatible : Must be "adi,axi-spdif-tx-1.00.a"
+ - reg : Must contain SPDIF core's registers location and length
+ - clocks : Pairs of phandle and specifier referencing the controller's clocks.
+   The controller expects two clocks, the clock used for the AXI interface and
+   the clock used as the sampling rate reference clock sample.
+ - clock-names: "axi" for the clock to the AXI interface, "ref" for the sample
+   rate reference clock.
+ - dmas: Pairs of phandle and specifier for the DMA channel that is used by
+   the core. The core expects one dma channel for transmit.
+ - dma-names : Must be "tx"
+
+For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties
+please check:
+	* resource-names.txt
+	* clock/clock-bindings.txt
+	* dma/dma.txt
+
+Example:
+
+	spdif: spdif@0x77400000 {
+		compatible = "adi,axi-spdif-tx-1.00.a";
+		reg = <0x77600000 0x1000>;
+		clocks = <&clk 15>, <&audio_clock>;
+		clock-names = "axi", "ref";
+		dmas = <&ps7_dma 0>;
+		dma-names = "tx";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/adi,ssm2602.txt b/kernel/Documentation/devicetree/bindings/sound/adi,ssm2602.txt
new file mode 100644
index 000000000..3b3302fe3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/adi,ssm2602.txt
@@ -0,0 +1,19 @@
+Analog Devices SSM2602, SSM2603 and SSM2604 I2S audio CODEC devices
+
+SSM2602 support both I2C and SPI as the configuration interface,
+the selection is made by the MODE strap-in pin.
+SSM2603 and SSM2604 only support I2C as the configuration interface.
+
+Required properties:
+
+  - compatible : One of "adi,ssm2602", "adi,ssm2603" or "adi,ssm2604"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+ Example:
+
+	ssm2602: ssm2602@1a {
+		compatible = "adi,ssm2602";
+		reg = <0x1a>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak4104.txt b/kernel/Documentation/devicetree/bindings/sound/ak4104.txt
new file mode 100644
index 000000000..deca5e18f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ak4104.txt
@@ -0,0 +1,25 @@
+AK4104 S/PDIF transmitter
+
+This device supports SPI mode only.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4104"
+
+  - reg : The chip select number on the SPI bus
+
+  - vdd-supply : A regulator node, providing 2.7V - 3.6V
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the device starts.
+
+Example:
+
+spdif: ak4104@0 {
+	compatible = "asahi-kasei,ak4104";
+	reg = <0>;
+	spi-max-frequency = <5000000>;
+	vdd-supply = <&vdd_3v3_reg>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak4554.c b/kernel/Documentation/devicetree/bindings/sound/ak4554.c
new file mode 100644
index 000000000..934fa0275
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ak4554.c
@@ -0,0 +1,11 @@
+AK4554 ADC/DAC
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4554"
+
+Example:
+
+ak4554-adc-dac {
+	compatible = "asahi-kasei,ak4554";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak4642.txt b/kernel/Documentation/devicetree/bindings/sound/ak4642.txt
new file mode 100644
index 000000000..623d4e70a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ak4642.txt
@@ -0,0 +1,17 @@
+AK4642 I2C transmitter
+
+This device supports I2C mode only.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak4642" or "asahi-kasei,ak4643" or "asahi-kasei,ak4648"
+  - reg : The chip select number on the I2C bus
+
+Example:
+
+&i2c {
+	ak4648: ak4648@0x12 {
+		compatible = "asahi-kasei,ak4642";
+		reg = <0x12>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ak5386.txt b/kernel/Documentation/devicetree/bindings/sound/ak5386.txt
new file mode 100644
index 000000000..ec3df3abb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ak5386.txt
@@ -0,0 +1,23 @@
+AK5386 Single-ended 24-Bit 192kHz delta-sigma ADC
+
+This device has no control interface.
+
+Required properties:
+
+  - compatible : "asahi-kasei,ak5386"
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset/power down pin.
+		 If specified, it will be deasserted at probe time.
+  - va-supply : a regulator spec, providing 5.0V
+  - vd-supply : a regulator spec, providing 3.3V
+
+Example:
+
+spdif: ak5386@0 {
+	compatible = "asahi-kasei,ak5386";
+	reset-gpio = <&gpio0 23>;
+	va-supply = <&vdd_5v0_reg>;
+	vd-supply = <&vdd_3v3_reg>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/alc5623.txt b/kernel/Documentation/devicetree/bindings/sound/alc5623.txt
new file mode 100644
index 000000000..26c86c98d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/alc5623.txt
@@ -0,0 +1,25 @@
+ALC5621/ALC5622/ALC5623 audio Codec
+
+Required properties:
+
+ - compatible:	"realtek,alc5623"
+ - reg:		the I2C address of the device.
+
+Optional properties:
+
+ - add-ctrl:	  Default register value for Reg-40h, Additional Control
+		  Register. If absent or has the value of 0, the
+		  register is untouched.
+
+ - jack-det-ctrl: Default register value for Reg-5Ah, Jack Detect
+		  Control Register. If absent or has value 0, the
+		  register is untouched.
+
+Example:
+
+	alc5621: alc5621@1a {
+		compatible = "alc5621";
+		reg = <0x1a>;
+		add-ctrl = <0x3700>;
+		jack-det-ctrl = <0x4810>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/alc5632.txt b/kernel/Documentation/devicetree/bindings/sound/alc5632.txt
new file mode 100644
index 000000000..ffd886d11
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/alc5632.txt
@@ -0,0 +1,43 @@
+ALC5632 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "realtek,alc5632"
+
+  - reg : the I2C address of the device.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+
+  - #gpio-cells : Should be two. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+Pins on the device (for linking into audio routes):
+
+  * SPK_OUTP
+  * SPK_OUTN
+  * HP_OUT_L
+  * HP_OUT_R
+  * AUX_OUT_P
+  * AUX_OUT_N
+  * LINE_IN_L
+  * LINE_IN_R
+  * PHONE_P
+  * PHONE_N
+  * MIC1_P
+  * MIC1_N
+  * MIC2_P
+  * MIC2_N
+  * MICBIAS1
+  * DMICDAT
+
+Example:
+
+alc5632: alc5632@1e {
+	compatible = "realtek,alc5632";
+	reg = <0x1a>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/armada-370db-audio.txt b/kernel/Documentation/devicetree/bindings/sound/armada-370db-audio.txt
new file mode 100644
index 000000000..bf984d238
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/armada-370db-audio.txt
@@ -0,0 +1,27 @@
+Device Tree bindings for the Armada 370 DB audio
+================================================
+
+These Device Tree bindings are used to describe the audio complex
+found on the Armada 370 DB platform.
+
+Mandatory properties:
+
+ * compatible: must be "marvell,a370db-audio"
+
+ * marvell,audio-controller: a phandle that points to the audio
+   controller of the Armada 370 SoC.
+
+ * marvell,audio-codec: a set of three phandles that points to:
+
+    1/ the analog audio codec connected to the Armada 370 SoC
+    2/ the S/PDIF transceiver
+    3/ the S/PDIF receiver
+
+Example:
+
+	sound {
+	      compatible = "marvell,a370db-audio";
+	      marvell,audio-controller = <&audio_controller>;
+	      marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>;
+	      status = "okay";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/arndale.txt b/kernel/Documentation/devicetree/bindings/sound/arndale.txt
new file mode 100644
index 000000000..0e7694638
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/arndale.txt
@@ -0,0 +1,24 @@
+Audio Binding for Arndale boards
+
+Required properties:
+- compatible : Can be the following,
+			"samsung,arndale-rt5631"
+
+- samsung,audio-cpu: The phandle of the Samsung I2S controller
+- samsung,audio-codec: The phandle of the audio codec
+
+Optional:
+- samsung,model: The name of the sound-card
+
+Arndale Boards has many audio daughter cards, one of them is
+rt5631/alc5631. Below example shows audio bindings for rt5631/
+alc5631 based codec.
+
+Example:
+
+sound {
+		compatible = "samsung,arndale-rt5631";
+
+		samsung,audio-cpu = <&i2s0>
+		samsung,audio-codec = <&rt5631>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt b/kernel/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt
new file mode 100644
index 000000000..9c5a9947b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt
@@ -0,0 +1,26 @@
+* Atmel at91sam9g20ek wm8731 audio complex
+
+Required properties:
+  - compatible: "atmel,at91sam9g20ek-wm8731-audio"
+  - atmel,model: The user-visible name of this sound complex.
+  - atmel,audio-routing: A list of the connections between audio components.
+  - atmel,ssc-controller: The phandle of the SSC controller
+  - atmel,audio-codec: The phandle of the WM8731 audio codec
+Optional properties:
+  - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt
+
+Example:
+sound {
+	compatible = "atmel,at91sam9g20ek-wm8731-audio";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pck0_as_mck>;
+
+	atmel,model = "wm8731 @ AT91SAMG20EK";
+
+	atmel,audio-routing =
+		"Ext Spk", "LHPOUT",
+		"Int MIC", "MICIN";
+
+	atmel,ssc-controller = <&ssc0>;
+	atmel,audio-codec = <&wm8731>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/atmel-sam9x5-wm8731-audio.txt b/kernel/Documentation/devicetree/bindings/sound/atmel-sam9x5-wm8731-audio.txt
new file mode 100644
index 000000000..072085708
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/atmel-sam9x5-wm8731-audio.txt
@@ -0,0 +1,35 @@
+* Atmel at91sam9x5ek wm8731 audio complex
+
+Required properties:
+  - compatible: "atmel,sam9x5-wm8731-audio"
+  - atmel,model: The user-visible name of this sound complex.
+  - atmel,ssc-controller: The phandle of the SSC controller
+  - atmel,audio-codec: The phandle of the WM8731 audio codec
+  - atmel,audio-routing: A list of the connections between audio components.
+    Each entry is a pair of strings, the first being the connection's sink,
+    the second being the connection's source.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headphone Jack
+ * Line In Jack
+
+wm8731 pins:
+cf Documentation/devicetree/bindings/sound/wm8731.txt
+
+Example:
+sound {
+	compatible = "atmel,sam9x5-wm8731-audio";
+
+	atmel,model = "wm8731 @ AT91SAM9X5EK";
+
+	atmel,audio-routing =
+		"Headphone Jack", "RHPOUT",
+		"Headphone Jack", "LHPOUT",
+		"LLINEIN", "Line In Jack",
+		"RLINEIN", "Line In Jack";
+
+	atmel,ssc-controller = <&ssc0>;
+	atmel,audio-codec = <&wm8731>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/atmel-wm8904.txt b/kernel/Documentation/devicetree/bindings/sound/atmel-wm8904.txt
new file mode 100644
index 000000000..8bbe50c88
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/atmel-wm8904.txt
@@ -0,0 +1,55 @@
+Atmel ASoC driver with wm8904 audio codec complex
+
+Required properties:
+  - compatible: "atmel,asoc-wm8904"
+  - atmel,model: The user-visible name of this sound complex.
+  - atmel,audio-routing: A list of the connections between audio components.
+    Each entry is a pair of strings, the first being the connection's sink,
+    the second being the connection's source. Valid names for sources and
+    sinks are the WM8904's pins, and the jacks on the board:
+
+    WM8904 pins:
+
+    * IN1L
+    * IN1R
+    * IN2L
+    * IN2R
+    * IN3L
+    * IN3R
+    * HPOUTL
+    * HPOUTR
+    * LINEOUTL
+    * LINEOUTR
+    * MICBIAS
+
+    Board connectors:
+
+    * Headphone Jack
+    * Line In Jack
+    * Mic
+
+  - atmel,ssc-controller: The phandle of the SSC controller
+  - atmel,audio-codec: The phandle of the WM8904 audio codec
+
+Optional properties:
+  - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt
+
+Example:
+sound {
+	compatible = "atmel,asoc-wm8904";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pck0_as_mck>;
+
+	atmel,model = "wm8904 @ AT91SAM9N12EK";
+
+	atmel,audio-routing =
+		"Headphone Jack", "HPOUTL",
+		"Headphone Jack", "HPOUTR",
+		"IN2L", "Line In Jack",
+		"IN2R", "Line In Jack",
+		"Mic", "MICBIAS",
+		"IN1L", "Mic";
+
+	atmel,ssc-controller = <&ssc0>;
+	atmel,audio-codec = <&wm8904>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/atmel_ac97c.txt b/kernel/Documentation/devicetree/bindings/sound/atmel_ac97c.txt
new file mode 100644
index 000000000..b151bd902
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/atmel_ac97c.txt
@@ -0,0 +1,20 @@
+* Atmel AC97 controller
+
+Required properties:
+  - compatible: "atmel,at91sam9263-ac97c"
+  - reg: Address and length of the register set for the device
+  - interrupts: Should contain AC97 interrupt
+  - ac97-gpios: Please refer to soc-ac97link.txt, only ac97-reset is used
+Optional properties:
+  - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt
+
+Example:
+sound@fffa0000 {
+       compatible = "atmel,at91sam9263-ac97c";
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_ac97>;
+       reg = <0xfffa0000 0x4000>;
+       interrupts = <18 IRQ_TYPE_LEVEL_HIGH 5>;
+
+       ac97-gpios = <&pioB 0 0 &pioB 2 0 &pioC 29 GPIO_ACTIVE_LOW>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt
new file mode 100644
index 000000000..65783de0a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/brcm,bcm2835-i2s.txt
@@ -0,0 +1,25 @@
+* Broadcom BCM2835 SoC I2S/PCM module
+
+Required properties:
+- compatible: "brcm,bcm2835-i2s"
+- reg: A list of base address and size entries:
+	* The first entry should cover the PCM registers
+	* The second entry should cover the PCM clock registers
+- dmas: List of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: Identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+  One of the DMA channels will be responsible for transmission (should be
+  named "tx") and one for reception (should be named "rx").
+
+Example:
+
+bcm2835_i2s: i2s@7e203000 {
+	compatible = "brcm,bcm2835-i2s";
+	reg = <0x7e203000 0x20>,
+	      <0x7e101098 0x02>;
+
+	dmas = <&dma 2>,
+	       <&dma 3>;
+	dma-names = "tx", "rx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt
new file mode 100644
index 000000000..befd125d1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt
@@ -0,0 +1,18 @@
+Bindings for I2S controller built into xtfpga Xtensa bitstreams.
+
+Required properties:
+- compatible: shall be "cdns,xtfpga-i2s".
+- reg: memory region (address and length) with device registers.
+- interrupts: interrupt for the device.
+- clocks: phandle to the clk used as master clock. I2S bus clock
+  is derived from it.
+
+Examples:
+
+	i2s0: xtfpga-i2s@0d080000 {
+		#sound-dai-cells = <0>;
+		compatible = "cdns,xtfpga-i2s";
+		reg = <0x0d080000 0x40>;
+		interrupts = <2 1>;
+		clocks = <&cdce706 4>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs35l32.txt b/kernel/Documentation/devicetree/bindings/sound/cs35l32.txt
new file mode 100644
index 000000000..1417d3f5c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs35l32.txt
@@ -0,0 +1,62 @@
+CS35L32 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs35l32"
+
+  - reg : the I2C address of the device for I2C. Address is determined by the level
+  of the AD0 pin. Level 0 is 0x40 while Level 1 is 0x41.
+
+  - VA-supply, VP-supply : power supplies for the device,
+  as covered in Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+  - reset-gpios : a GPIO spec for the reset pin. If specified, it will be
+  deasserted before communication to the codec starts.
+
+  - cirrus,boost-manager : Boost voltage control.
+  0 = Automatically managed.  Boost-converter output voltage is the higher
+  of the two: Class G or adaptive LED voltage.
+  1 = Automatically managed irrespective of audio, adapting for low-power
+  dissipation when LEDs are ON, and operating in Fixed-Boost Bypass Mode
+  if LEDs are OFF (VBST = VP).
+  2 = (Default) Boost voltage fixed in Bypass Mode (VBST = VP).
+  3 = Boost voltage fixed at 5 V.
+
+  - cirrus,sdout-datacfg : Data configuration for dual CS35L32 applications only.
+  Determines the data packed in a two-CS35L32 configuration.
+  0 = Left/right channels VMON[11:0], IMON[11:0], VPMON[7:0].
+  1 = Left/right channels VMON[11:0], IMON[11:0], STATUS.
+  2 = (Default) left/right channels VMON[15:0], IMON [15:0].
+  3 = Left/right channels VPMON[7:0], STATUS.
+
+  - cirrus,sdout-share : SDOUT sharing. Determines whether one or two CS35L32
+  devices are on board sharing SDOUT.
+  0 = (Default) One IC.
+  1 = Two IC's.
+
+  - cirrus,battery-recovery : Low battery nominal recovery threshold, rising VP.
+  0 = 3.1V
+  1 = 3.2V
+  2 = 3.3V (Default)
+  3 = 3.4V
+
+  - cirrus,battery-threshold : Low battery nominal threshold, falling VP.
+  0 = 3.1V
+  1 = 3.2V
+  2 = 3.3V
+  3 = 3.4V (Default)
+  4 = 3.5V
+  5 = 3.6V
+
+Example:
+
+codec: codec@40 {
+	compatible = "cirrus,cs35l32";
+	reg = <0x40>;
+	reset-gpios = <&gpio 10 0>;
+	cirrus,boost-manager = <0x03>;
+	cirrus,sdout-datacfg = <0x02>;
+	VA-supply = <&reg_audio>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs4265.txt b/kernel/Documentation/devicetree/bindings/sound/cs4265.txt
new file mode 100644
index 000000000..380fff8e4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs4265.txt
@@ -0,0 +1,29 @@
+CS4265 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "cirrus,cs4265"
+
+  - reg : the I2C address of the device for I2C. The I2C address depends on
+          the state of the AD0 pin.  If AD0 is high, the i2c address is 0x4f.
+          If it is low, the i2c address is 0x4e.
+
+Optional properties:
+
+  - reset-gpios : a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+Examples:
+
+codec_ad0_high: cs4265@4f { /* AD0 Pin is high */
+	compatible = "cirrus,cs4265";
+	reg = <0x4f>;
+};
+
+
+codec_ad0_low: cs4265@4e { /* AD0 Pin is low */
+	compatible = "cirrus,cs4265";
+	reg = <0x4e>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs4270.txt b/kernel/Documentation/devicetree/bindings/sound/cs4270.txt
new file mode 100644
index 000000000..6b222f9b8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs4270.txt
@@ -0,0 +1,21 @@
+CS4270 audio CODEC
+
+The driver for this device currently only supports I2C.
+
+Required properties:
+
+  - compatible : "cirrus,cs4270"
+
+  - reg : the I2C address of the device for I2C
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+Example:
+
+codec: cs4270@48 {
+	compatible = "cirrus,cs4270";
+	reg = <0x48>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs4271.txt b/kernel/Documentation/devicetree/bindings/sound/cs4271.txt
new file mode 100644
index 000000000..e2cd1d753
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs4271.txt
@@ -0,0 +1,50 @@
+Cirrus Logic CS4271 DT bindings
+
+This driver supports both the I2C and the SPI bus.
+
+Required properties:
+
+ - compatible: "cirrus,cs4271"
+
+For required properties on SPI, please consult
+Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Required properties on I2C:
+
+ - reg: the i2c address
+
+
+Optional properties:
+
+ - reset-gpio: 	a GPIO spec to define which pin is connected to the chip's
+		!RESET pin
+ - cirrus,amuteb-eq-bmutec:	When given, the Codec's AMUTEB=BMUTEC flag
+				is enabled.
+ - cirrus,enable-soft-reset:
+	The CS4271 requires its LRCLK and MCLK to be stable before its RESET
+	line is de-asserted. That also means that clocks cannot be changed
+	without putting the chip back into hardware reset, which also requires
+	a complete re-initialization of all registers.
+
+	One (undocumented) workaround is to assert and de-assert the PDN bit
+	in the MODE2 register. This workaround can be enabled with this DT
+	property.
+
+	Note that this is not needed in case the clocks are stable
+	throughout the entire runtime of the codec.
+
+Examples:
+
+	codec_i2c: cs4271@10 {
+		compatible = "cirrus,cs4271";
+		reg = <0x10>;
+		reset-gpio = <&gpio 23 0>;
+	};
+
+	codec_spi: cs4271@0 {
+		compatible = "cirrus,cs4271";
+		reg = <0x0>;
+		reset-gpio = <&gpio 23 0>;
+		spi-max-frequency = <6000000>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs42l52.txt b/kernel/Documentation/devicetree/bindings/sound/cs42l52.txt
new file mode 100644
index 000000000..bc03c9312
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs42l52.txt
@@ -0,0 +1,46 @@
+CS42L52 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs42l52"
+
+  - reg : the I2C address of the device for I2C
+
+Optional properties:
+
+  - cirrus,reset-gpio : GPIO controller's phandle and the number
+  of the GPIO used to reset the codec.
+
+  - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
+  Allowable values of 0x00 through 0x0F. These are raw values written to the
+  register, not the actual frequency. The frequency is determined by the following.
+  Frequency = (64xFs)/(N+2)
+  N = chgfreq_val
+  Fs = Sample Rate (variable)
+
+  - cirrus,mica-differential-cfg : boolean, If present, then the MICA input is configured
+  as a differential input. If not present then the MICA input is configured as
+  Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
+
+  - cirrus,micb-differential-cfg : boolean, If present, then the MICB input is configured
+  as a differential input. If not present then the MICB input is configured as
+  Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
+
+  - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin
+  0 = 0.5 x VA
+  1 = 0.6 x VA
+  2 = 0.7 x VA
+  3 = 0.8 x VA
+  4 = 0.83 x VA
+  5 = 0.91 x VA
+
+Example:
+
+codec: codec@4a {
+	compatible = "cirrus,cs42l52";
+	reg = <0x4a>;
+	reset-gpio = <&gpio 10 0>;
+	cirrus,chgfreq-divisor = <0x05>;
+	cirrus.mica-differential-cfg;
+	cirrus,micbias-lvl = <5>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs42l56.txt b/kernel/Documentation/devicetree/bindings/sound/cs42l56.txt
new file mode 100644
index 000000000..4feb0eb27
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs42l56.txt
@@ -0,0 +1,63 @@
+CS42L52 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs42l56"
+
+  - reg : the I2C address of the device for I2C
+
+  - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
+  as covered in Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+  - cirrus,gpio-nreset : GPIO controller's phandle and the number
+  of the GPIO used to reset the codec.
+
+  - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
+  Allowable values of 0x00 through 0x0F. These are raw values written to the
+  register, not the actual frequency. The frequency is determined by the following.
+  Frequency = MCLK / 4 * (N+2)
+  N = chgfreq_val
+  MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit.
+
+  - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
+  as a pseudo-differential input referenced to AIN1REF/AIN3A.
+
+  - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
+  as a pseudo-differential input referenced to AIN2REF/AIN3B.
+
+  - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
+  0 = 0.5 x VA
+  1 = 0.6 x VA
+  2 = 0.7 x VA
+  3 = 0.8 x VA
+  4 = 0.83 x VA
+  5 = 0.91 x VA
+
+  - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout
+  Amplifiers adapt to the output signal levels.
+  0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings.
+  1 = Fixed - Headphone and Line Amp supply = + or - VCP/2.
+  2 = Fixed - Headphone and Line Amp supply = + or - VCP.
+  3 = Adapted to Signal; Voltage level is dynamically determined by the output signal.
+
+  - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass
+  Filter.
+  0 = 1.8Hz
+  1 = 119Hz
+  2 = 236Hz
+  3 = 464Hz
+
+
+Example:
+
+codec: codec@4b {
+	compatible = "cirrus,cs42l56";
+	reg = <0x4b>;
+	gpio-reset = <&gpio 10 0>;
+	cirrus,chgfreq-divisor = <0x05>;
+	cirrus.ain1_ref_cfg;
+	cirrus,micbias-lvl = <5>;
+	VA-supply = <&reg_audio>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs42l73.txt b/kernel/Documentation/devicetree/bindings/sound/cs42l73.txt
new file mode 100644
index 000000000..80ae910db
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs42l73.txt
@@ -0,0 +1,22 @@
+CS42L73 audio CODEC
+
+Required properties:
+
+  - compatible : "cirrus,cs42l73"
+
+  - reg : the I2C address of the device for I2C
+
+Optional properties:
+
+  - reset_gpio : a GPIO spec for the reset pin.
+  - chgfreq    : Charge Pump Frequency values 0x00-0x0F
+
+
+Example:
+
+codec: cs42l73@4a {
+	compatible = "cirrus,cs42l73";
+	reg = <0x4a>;
+	reset_gpio = <&gpio 10 0>;
+	chgfreq = <0x05>;
+};
\ No newline at end of file
diff --git a/kernel/Documentation/devicetree/bindings/sound/cs42xx8.txt b/kernel/Documentation/devicetree/bindings/sound/cs42xx8.txt
new file mode 100644
index 000000000..f631fbca6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/cs42xx8.txt
@@ -0,0 +1,28 @@
+CS42448/CS42888 audio CODEC
+
+Required properties:
+
+  - compatible : must contain one of "cirrus,cs42448" and "cirrus,cs42888"
+
+  - reg : the I2C address of the device for I2C
+
+  - clocks : a list of phandles + clock-specifiers, one for each entry in
+    clock-names
+
+  - clock-names : must contain "mclk"
+
+  - VA-supply, VD-supply, VLS-supply, VLC-supply: power supplies for the device,
+    as covered in Documentation/devicetree/bindings/regulator/regulator.txt
+
+Example:
+
+codec: cs42888@48 {
+	compatible = "cirrus,cs42888";
+	reg = <0x48>;
+	clocks = <&codec_mclk 0>;
+	clock-names = "mclk";
+	VA-supply = <&reg_audio>;
+	VD-supply = <&reg_audio>;
+	VLS-supply = <&reg_audio>;
+	VLC-supply = <&reg_audio>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/da9055.txt b/kernel/Documentation/devicetree/bindings/sound/da9055.txt
new file mode 100644
index 000000000..ed1b7cc6f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/da9055.txt
@@ -0,0 +1,22 @@
+* Dialog DA9055 Audio CODEC
+
+DA9055 provides Audio CODEC support (I2C only).
+
+The Audio CODEC device in DA9055 has it's own I2C address which is configurable,
+so the device is instantiated separately from the PMIC (MFD) device.
+
+For details on accompanying PMIC I2C device, see the following:
+Documentation/devicetree/bindings/mfd/da9055.txt
+
+Required properties:
+
+  - compatible: "dlg,da9055-codec"
+  - reg: Specifies the I2C slave address
+
+
+Example:
+
+	codec: da9055-codec@1a {
+		compatible = "dlg,da9055-codec";
+		reg = <0x1a>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt b/kernel/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
new file mode 100644
index 000000000..963e10051
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/davinci-evm-audio.txt
@@ -0,0 +1,49 @@
+* Texas Instruments SoC audio setups with TLV320AIC3X Codec
+
+Required properties:
+- compatible : "ti,da830-evm-audio" : forDM365/DA8xx/OMAPL1x/AM33xx
+- ti,model : The user-visible name of this sound complex.
+- ti,audio-codec : The phandle of the TLV320AIC3x audio codec
+- ti,mcasp-controller : The phandle of the McASP controller
+- ti,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the codec's pins, and the jacks on the board:
+
+Optional properties:
+- ti,codec-clock-rate : The Codec Clock rate (in Hz) applied to the Codec.
+- clocks : Reference to the master clock
+- clock-names : The clock should be named "mclk"
+- Either codec-clock-rate or the codec-clock reference has to be defined. If
+  the both are defined the driver attempts to set referenced clock to the
+  defined rate and takes the rate from the clock reference.
+
+  Board connectors:
+
+  * Headphone Jack
+  * Line Out
+  * Mic Jack
+  * Line In
+
+
+Example:
+
+sound {
+	compatible = "ti,da830-evm-audio";
+	ti,model = "DA830 EVM";
+	ti,audio-codec = <&tlv320aic3x>;
+	ti,mcasp-controller = <&mcasp1>;
+	ti,codec-clock-rate = <12000000>;
+	ti,audio-routing =
+		"Headphone Jack",       "HPLOUT",
+		"Headphone Jack",       "HPROUT",
+		"Line Out",             "LLOUT",
+		"Line Out",             "RLOUT",
+		"MIC3L",                "Mic Bias 2V",
+		"MIC3R",                "Mic Bias 2V",
+		"Mic Bias 2V",          "Mic Jack",
+		"LINE1L",               "Line In",
+		"LINE2L",               "Line In",
+		"LINE1R",               "Line In",
+		"LINE2R",               "Line In";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/kernel/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt
new file mode 100644
index 000000000..46bc9829c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt
@@ -0,0 +1,60 @@
+Texas Instruments McASP controller
+
+Required properties:
+- compatible :
+	"ti,dm646x-mcasp-audio"	: for DM646x platforms
+	"ti,da830-mcasp-audio"	: for both DA830 & DA850 platforms
+	"ti,am33xx-mcasp-audio"	: for AM33xx platforms (AM33xx, AM43xx, TI81xx)
+	"ti,dra7-mcasp-audio"	: for DRA7xx platforms
+
+- reg : Should contain reg specifiers for the entries in the reg-names property.
+- reg-names : Should contain:
+         * "mpu" for the main registers (required). For compatibility with
+           existing software, it is recommended this is the first entry.
+         * "dat" for separate data port register access (optional).
+- op-mode : I2S/DIT ops mode. 0 for I2S mode. 1 for DIT mode used for S/PDIF,
+  	    IEC60958-1, and AES-3 formats.
+- tdm-slots : Slots for TDM operation. Indicates number of channels transmitted
+  	      or received over one serializer.
+- serial-dir : A list of serializer configuration. Each entry is a number
+               indication for serializer pin direction.
+               (0 - INACTIVE, 1 - TX, 2 - RX)
+- dmas: two element list of DMA controller phandles and DMA request line
+        ordered pairs.
+- dma-names: identifier string for each DMA request line in the dmas property.
+	     These strings correspond 1:1 with the ordered pairs in dmas. The dma
+	     identifiers must be "rx" and "tx".
+
+Optional properties:
+
+- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0
+- tx-num-evt : FIFO levels.
+- rx-num-evt : FIFO levels.
+- sram-size-playback : size of sram to be allocated during playback
+- sram-size-capture  : size of sram to be allocated during capture
+- interrupts : Interrupt numbers for McASP
+- interrupt-names : Known interrupt names are "tx" and "rx"
+- pinctrl-0: Should specify pin control group used for this controller.
+- pinctrl-names: Should contain only one value - "default", for more details
+  		 please refer to pinctrl-bindings.txt
+- fck_parent : Should contain a valid clock name which will be used as parent
+	       for the McASP fck
+
+Example:
+
+mcasp0: mcasp0@1d00000 {
+	compatible = "ti,da830-mcasp-audio";
+	reg = <0x100000 0x3000>;
+	reg-names "mpu";
+	interrupts = <82>, <83>;
+	interrupt-names = "tx", "rx";
+	op-mode = <0>;		/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <
+			0 0 0 0	/* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 0 0
+			0 0 0 1
+			2 0 0 0 >;
+	tx-num-evt = <1>;
+	rx-num-evt = <1>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/designware-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/designware-i2s.txt
new file mode 100644
index 000000000..7bb54247f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/designware-i2s.txt
@@ -0,0 +1,31 @@
+DesignWare I2S controller
+
+Required properties:
+ - compatible : Must be "snps,designware-i2s"
+ - reg : Must contain the I2S core's registers location and length
+ - clocks : Pairs of phandle and specifier referencing the controller's
+   clocks. The controller expects one clock: the clock used as the sampling
+   rate reference clock sample.
+ - clock-names : "i2sclk" for the sample rate reference clock.
+ - dmas: Pairs of phandle and specifier for the DMA channels that are used by
+   the core. The core expects one or two dma channels: one for transmit and
+   one for receive.
+ - dma-names : "tx" for the transmit channel, "rx" for the receive channel.
+
+For more details on the 'dma', 'dma-names', 'clock' and 'clock-names'
+properties please check:
+	* resource-names.txt
+	* clock/clock-bindings.txt
+	* dma/dma.txt
+
+Example:
+
+	soc_i2s: i2s@7ff90000 {
+		compatible = "snps,designware-i2s";
+		reg = <0x0 0x7ff90000 0x0 0x1000>;
+		clocks = <&scpi_i2sclk 0>;
+		clock-names = "i2sclk";
+		#sound-dai-cells = <0>;
+		dmas = <&dma0 5>;
+		dma-names = "tx";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/es8328.txt b/kernel/Documentation/devicetree/bindings/sound/es8328.txt
new file mode 100644
index 000000000..30ea8a318
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/es8328.txt
@@ -0,0 +1,38 @@
+Everest ES8328 audio CODEC
+
+This device supports both I2C and SPI.
+
+Required properties:
+
+  - compatible : "everest,es8328"
+  - DVDD-supply : Regulator providing digital core supply voltage 1.8 - 3.6V
+  - AVDD-supply : Regulator providing analog supply voltage 3.3V
+  - PVDD-supply : Regulator providing digital IO supply voltage 1.8 - 3.6V
+  - IPVDD-supply : Regulator providing analog output voltage 3.3V
+  - clocks : A 22.5792 or 11.2896 MHz clock
+  - reg : the I2C address of the device for I2C, the chip select number for SPI
+
+Pins on the device (for linking into audio routes):
+
+  * LOUT1
+  * LOUT2
+  * ROUT1
+  * ROUT2
+  * LINPUT1
+  * RINPUT1
+  * LINPUT2
+  * RINPUT2
+  * Mic Bias
+
+
+Example:
+
+codec: es8328@11 {
+	compatible = "everest,es8328";
+	DVDD-supply = <&reg_3p3v>;
+	AVDD-supply = <&reg_3p3v>;
+	PVDD-supply = <&reg_3p3v>;
+	HPVDD-supply = <&reg_3p3v>;
+	clocks = <&clks 169>;
+	reg = <0x11>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt b/kernel/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt
new file mode 100644
index 000000000..6dfa88c4d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt
@@ -0,0 +1,26 @@
+Audio complex for Eukrea boards with tlv320aic23 codec.
+
+Required properties:
+
+  - compatible		: "eukrea,asoc-tlv320"
+
+  - eukrea,model	: The user-visible name of this sound complex.
+
+  - ssi-controller	: The phandle of the SSI controller.
+
+  - fsl,mux-int-port	: The internal port of the i.MX audio muxer (AUDMUX).
+
+  - fsl,mux-ext-port	: The external port of the i.MX audio muxer.
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+	sound {
+		compatible = "eukrea,asoc-tlv320";
+		eukrea,model = "imx51-eukrea-tlv320aic23";
+		ssi-controller = <&ssi2>;
+		fsl,mux-int-port = <2>;
+		fsl,mux-ext-port = <3>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/kernel/Documentation/devicetree/bindings/sound/fsl,asrc.txt
new file mode 100644
index 000000000..b93362a57
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl,asrc.txt
@@ -0,0 +1,60 @@
+Freescale Asynchronous Sample Rate Converter (ASRC) Controller
+
+The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a
+signal associated with an input clock into a signal associated with a different
+output clock. The driver currently works as a Front End of DPCM with other Back
+Ends Audio controller such as ESAI, SSI and SAI. It has three pairs to support
+three substreams within totally 10 channels.
+
+Required properties:
+
+  - compatible		: Contains "fsl,imx35-asrc" or "fsl,imx53-asrc".
+
+  - reg			: Offset and length of the register set for the device.
+
+  - interrupts		: Contains the spdif interrupt.
+
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names		: Contains "rxa", "rxb", "rxc", "txa", "txb" and "txc".
+
+  - clocks		: Contains an entry for each entry in clock-names.
+
+  - clock-names		: Contains the following entries
+	"mem"		  Peripheral access clock to access registers.
+	"ipg"		  Peripheral clock to driver module.
+	"asrck_<0-f>"	  Clock sources for input and output clock.
+
+   - big-endian		: If this property is absent, the little endian mode
+			  will be in use as default. Otherwise, the big endian
+			  mode will be in use for all the device registers.
+
+   - fsl,asrc-rate	: Defines a mutual sample rate used by DPCM Back Ends.
+
+   - fsl,asrc-width	: Defines a mutual sample width used by DPCM Back Ends.
+
+Example:
+
+asrc: asrc@02034000 {
+	compatible = "fsl,imx53-asrc";
+	reg = <0x02034000 0x4000>;
+	interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks 107>, <&clks 107>, <&clks 0>,
+	       <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+	       <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+	       <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+	       <&clks 107>, <&clks 0>, <&clks 0>;
+	clock-names = "mem", "ipg", "asrck0",
+		"asrck_1", "asrck_2", "asrck_3", "asrck_4",
+		"asrck_5", "asrck_6", "asrck_7", "asrck_8",
+		"asrck_9", "asrck_a", "asrck_b", "asrck_c",
+		"asrck_d", "asrck_e", "asrck_f";
+	dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>,
+	     <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
+	dma-names = "rxa", "rxb", "rxc",
+		"txa", "txb", "txc";
+	fsl,asrc-rate  = <48000>;
+	fsl,asrc-width = <16>;
+	status = "okay";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl,esai.txt b/kernel/Documentation/devicetree/bindings/sound/fsl,esai.txt
new file mode 100644
index 000000000..d3b6b5f48
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl,esai.txt
@@ -0,0 +1,58 @@
+Freescale Enhanced Serial Audio Interface (ESAI) Controller
+
+The Enhanced Serial Audio Interface (ESAI) provides a full-duplex serial port
+for serial communication with a variety of serial devices, including industry
+standard codecs, Sony/Phillips Digital Interface (S/PDIF) transceivers, and
+other DSPs. It has up to six transmitters and four receivers.
+
+Required properties:
+
+  - compatible		: Compatible list, must contain "fsl,imx35-esai" or
+			  "fsl,vf610-esai"
+
+  - reg			: Offset and length of the register set for the device.
+
+  - interrupts		: Contains the spdif interrupt.
+
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
+
+  - clocks		: Contains an entry for each entry in clock-names.
+
+  - clock-names		: Includes the following entries:
+	"core"		  The core clock used to access registers
+	"extal"		  The esai baud clock for esai controller used to
+			  derive HCK, SCK and FS.
+	"fsys"		  The system clock derived from ahb clock used to
+			  derive HCK, SCK and FS.
+
+  - fsl,fifo-depth	: The number of elements in the transmit and receive
+			  FIFOs. This number is the maximum allowed value for
+			  TFCR[TFWM] or RFCR[RFWM].
+
+  - fsl,esai-synchronous: This is a boolean property. If present, indicating
+			  that ESAI would work in the synchronous mode, which
+			  means all the settings for Receiving would be
+			  duplicated from Transmition related registers.
+
+  - big-endian		: If this property is absent, the native endian mode
+			  will be in use as default, or the big endian mode
+			  will be in use for all the device registers.
+
+Example:
+
+esai: esai@02024000 {
+	compatible = "fsl,imx35-esai";
+	reg = <0x02024000 0x4000>;
+	interrupts = <0 51 0x04>;
+	clocks = <&clks 208>, <&clks 118>, <&clks 208>;
+	clock-names = "core", "extal", "fsys";
+	dmas = <&sdma 23 21 0>, <&sdma 24 21 0>;
+	dma-names = "rx", "tx";
+	fsl,fifo-depth = <128>;
+	fsl,esai-synchronous;
+	big-endian;
+	status = "disabled";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/kernel/Documentation/devicetree/bindings/sound/fsl,spdif.txt
new file mode 100644
index 000000000..b5ee32ee3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl,spdif.txt
@@ -0,0 +1,58 @@
+Freescale Sony/Philips Digital Interface Format (S/PDIF) Controller
+
+The Freescale S/PDIF audio block is a stereo transceiver that allows the
+processor to receive and transmit digital audio via an coaxial cable or
+a fibre cable.
+
+Required properties:
+
+  - compatible		: Compatible list, must contain "fsl,imx35-spdif".
+
+  - reg			: Offset and length of the register set for the device.
+
+  - interrupts		: Contains the spdif interrupt.
+
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
+
+  - clocks		: Contains an entry for each entry in clock-names.
+
+  - clock-names		: Includes the following entries:
+	"core"		  The core clock of spdif controller.
+	"rxtx<0-7>"	  Clock source list for tx and rx clock.
+			  This clock list should be identical to the source
+			  list connecting to the spdif clock mux in "SPDIF
+			  Transceiver Clock Diagram" of SoC reference manual.
+			  It can also be referred to TxClk_Source bit of
+			  register SPDIF_STC.
+
+   - big-endian		: If this property is absent, the native endian mode
+			  will be in use as default, or the big endian mode
+			  will be in use for all the device registers.
+
+Example:
+
+spdif: spdif@02004000 {
+	compatible = "fsl,imx35-spdif";
+	reg = <0x02004000 0x4000>;
+	interrupts = <0 52 0x04>;
+	dmas = <&sdma 14 18 0>,
+	       <&sdma 15 18 0>;
+	dma-names = "rx", "tx";
+
+	clocks = <&clks 197>, <&clks 3>,
+	       <&clks 197>, <&clks 107>,
+	       <&clks 0>, <&clks 118>,
+	       <&clks 62>, <&clks 139>,
+	       <&clks 0>;
+	clock-names = "core", "rxtx0",
+		"rxtx1", "rxtx2",
+		"rxtx3", "rxtx4",
+		"rxtx5", "rxtx6",
+		"rxtx7";
+
+	big-endian;
+	status = "okay";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl,ssi.txt b/kernel/Documentation/devicetree/bindings/sound/fsl,ssi.txt
new file mode 100644
index 000000000..5b76be45d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl,ssi.txt
@@ -0,0 +1,87 @@
+Freescale Synchronous Serial Interface
+
+The SSI is a serial device that communicates with audio codecs.  It can
+be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+Required properties:
+- compatible:       Compatible list, should contain one of the following
+                    compatibles:
+                      fsl,mpc8610-ssi
+                      fsl,imx51-ssi
+                      fsl,imx35-ssi
+                      fsl,imx21-ssi
+- cell-index:       The SSI, <0> = SSI1, <1> = SSI2, and so on.
+- reg:              Offset and length of the register set for the device.
+- interrupts:       <a b> where a is the interrupt number and b is a
+                    field that represents an encoding of the sense and
+                    level information for the interrupt.  This should be
+                    encoded based on the information in section 2)
+                    depending on the type of interrupt controller you
+                    have.
+- interrupt-parent: The phandle for the interrupt controller that
+                    services interrupts for this device.
+- fsl,playback-dma: Phandle to a node for the DMA channel to use for
+                    playback of audio.  This is typically dictated by SOC
+                    design.  See the notes below.
+- fsl,capture-dma:  Phandle to a node for the DMA channel to use for
+                    capture (recording) of audio.  This is typically dictated
+                    by SOC design.  See the notes below.
+- fsl,fifo-depth:   The number of elements in the transmit and receive FIFOs.
+                    This number is the maximum allowed value for SFCSR[TFWM0].
+- fsl,ssi-asynchronous:
+                    If specified, the SSI is to be programmed in asynchronous
+                    mode.  In this mode, pins SRCK, STCK, SRFS, and STFS must
+                    all be connected to valid signals.  In synchronous mode,
+                    SRCK and SRFS are ignored.  Asynchronous mode allows
+                    playback and capture to use different sample sizes and
+                    sample rates.  Some drivers may require that SRCK and STCK
+                    be connected together, and SRFS and STFS be connected
+                    together.  This would still allow different sample sizes,
+                    but not different sample rates.
+ - clocks:          "ipg" - Required clock for the SSI unit
+                    "baud" - Required clock for SSI master mode. Otherwise this
+		      clock is not used
+
+Required are also ac97 link bindings if ac97 is used. See
+Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary
+bindings.
+
+Optional properties:
+- codec-handle:     Phandle to a 'codec' node that defines an audio
+                    codec connected to this SSI.  This node is typically
+                    a child of an I2C or other control node.
+- fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to
+		    filter the codec stream. This is necessary for some boards
+		    where an incompatible codec is connected to this SSI, e.g.
+		    on pca100 and pcm043.
+- dmas:		    Generic dma devicetree binding as described in
+		    Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names:	    Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq
+		    is not defined.
+- fsl,mode:         The operating mode for the AC97 interface only.
+                    "ac97-slave" - AC97 mode, SSI is clock slave
+                    "ac97-master" - AC97 mode, SSI is clock master
+
+Child 'codec' node required properties:
+- compatible:       Compatible list, contains the name of the codec
+
+Child 'codec' node optional properties:
+- clock-frequency:  The frequency of the input clock, which typically comes
+                    from an on-board dedicated oscillator.
+
+Notes on fsl,playback-dma and fsl,capture-dma:
+
+On SOCs that have an SSI, specific DMA channels are hard-wired for playback
+and capture.  On the MPC8610, for example, SSI1 must use DMA channel 0 for
+playback and DMA channel 1 for capture.  SSI2 must use DMA channel 2 for
+playback and DMA channel 3 for capture.  The developer can choose which
+DMA controller to use, but the channels themselves are hard-wired.  The
+purpose of these two properties is to represent this hardware design.
+
+The device tree nodes for the DMA channels that are referenced by
+"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
+"fsl,ssi-dma-channel".  The SOC-specific compatible string (e.g.
+"fsl,mpc8610-dma-channel") can remain.  If these nodes are left as
+"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
+drivers (fsldma) will attempt to use them, and it will conflict with the
+sound drivers.
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt b/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
new file mode 100644
index 000000000..a96774c19
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl-asoc-card.txt
@@ -0,0 +1,82 @@
+Freescale Generic ASoC Sound Card with ASRC support
+
+The Freescale Generic ASoC Sound Card can be used, ideally, for all Freescale
+SoCs connecting with external CODECs.
+
+The idea of this generic sound card is a bit like ASoC Simple Card. However,
+for Freescale SoCs (especially those released in recent years), most of them
+have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And
+this is a specific feature that might be painstakingly controlled and merged
+into the Simple Card.
+
+So having this generic sound card allows all Freescale SoC users to benefit
+from the simplification of a new card support and the capability of the wide
+sample rates support through ASRC.
+
+Note: The card is initially designed for those sound cards who use I2S and
+      PCM DAI formats. However, it'll be also possible to support those non
+      I2S/PCM type sound cards, such as S/PDIF audio and HDMI audio, as long
+      as the driver has been properly upgraded.
+
+
+The compatible list for this generic sound card currently:
+ "fsl,imx-audio-cs42888"
+
+ "fsl,imx-audio-wm8962"
+ (compatible with Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt)
+
+ "fsl,imx-audio-sgtl5000"
+ (compatible with Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt)
+
+Required properties:
+
+  - compatible		: Contains one of entries in the compatible list.
+
+  - model		: The user-visible name of this sound complex
+
+  - audio-cpu		: The phandle of an CPU DAI controller
+
+  - audio-codec		: The phandle of an audio codec
+
+  - audio-routing	: A list of the connections between audio components.
+			  Each entry is a pair of strings, the first being the
+			  connection's sink, the second being the connection's
+			  source. There're a few pre-designed board connectors:
+			   * Line Out Jack
+			   * Line In Jack
+			   * Headphone Jack
+			   * Mic Jack
+			   * Ext Spk
+			   * AMIC (stands for Analog Microphone Jack)
+			   * DMIC (stands for Digital Microphone Jack)
+
+			  Note: The "Mic Jack" and "AMIC" are redundant while
+			        coexsiting in order to support the old bindings
+				of wm8962 and sgtl5000.
+
+Optional properties:
+
+  - audio-asrc		: The phandle of ASRC. It can be absent if there's no
+			  need to add ASRC support via DPCM.
+
+Example:
+sound-cs42888 {
+	compatible = "fsl,imx-audio-cs42888";
+	model = "cs42888-audio";
+	audio-cpu = <&esai>;
+	audio-asrc = <&asrc>;
+	audio-codec = <&cs42888>;
+	audio-routing =
+		"Line Out Jack", "AOUT1L",
+		"Line Out Jack", "AOUT1R",
+		"Line Out Jack", "AOUT2L",
+		"Line Out Jack", "AOUT2R",
+		"Line Out Jack", "AOUT3L",
+		"Line Out Jack", "AOUT3R",
+		"Line Out Jack", "AOUT4L",
+		"Line Out Jack", "AOUT4R",
+		"AIN1L", "Line In Jack",
+		"AIN1R", "Line In Jack",
+		"AIN2L", "Line In Jack",
+		"AIN2R", "Line In Jack";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/fsl-sai.txt b/kernel/Documentation/devicetree/bindings/sound/fsl-sai.txt
new file mode 100644
index 000000000..044e5d76e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/fsl-sai.txt
@@ -0,0 +1,73 @@
+Freescale Synchronous Audio Interface (SAI).
+
+The SAI is based on I2S module that used communicating with audio codecs,
+which provides a synchronous audio interface that supports fullduplex
+serial interfaces with frame synchronization such as I2S, AC97, TDM, and
+codec/DSP interfaces.
+
+Required properties:
+
+  - compatible		: Compatible list, contains "fsl,vf610-sai" or
+			  "fsl,imx6sx-sai".
+
+  - reg			: Offset and length of the register set for the device.
+
+  - clocks		: Must contain an entry for each entry in clock-names.
+
+  - clock-names		: Must include the "bus" for register access and
+			  "mclk1", "mclk2", "mclk3" for bit clock and frame
+			  clock providing.
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
+
+  - pinctrl-names	: Must contain a "default" entry.
+
+  - pinctrl-NNN		: One property must exist for each entry in
+			  pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
+			  for details of the property values.
+
+  - big-endian		: Boolean property, required if all the FTM_PWM
+			  registers are big-endian rather than little-endian.
+
+  - lsb-first		: Configures whether the LSB or the MSB is transmitted
+			  first for the fifo data. If this property is absent,
+			  the MSB is transmitted first as default, or the LSB
+			  is transmitted first.
+
+  - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
+			  that SAI will work in the synchronous mode (sync Tx
+			  with Rx) which means both the transimitter and the
+			  receiver will send and receive data by following
+			  receiver's bit clocks and frame sync clocks.
+
+  - fsl,sai-asynchronous: This is a boolean property. If present, indicating
+			  that SAI will work in the asynchronous mode, which
+			  means both transimitter and receiver will send and
+			  receive data by following their own bit clocks and
+			  frame sync clocks separately.
+
+Note:
+- If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the
+  default synchronous mode (sync Rx with Tx) will be used, which means both
+  transimitter and receiver will send and receive data by following clocks
+  of transimitter.
+- fsl,sai-asynchronous and fsl,sai-synchronous-rx are exclusive.
+
+Example:
+sai2: sai@40031000 {
+	      compatible = "fsl,vf610-sai";
+	      reg = <0x40031000 0x1000>;
+	      pinctrl-names = "default";
+	      pinctrl-0 = <&pinctrl_sai2_1>;
+	      clocks = <&clks VF610_CLK_PLATFORM_BUS>,
+		     <&clks VF610_CLK_SAI2>,
+		     <&clks 0>, <&clks 0>;
+	      clock-names = "bus", "mclk1", "mclk2", "mclk3";
+	      dma-names = "tx", "rx";
+	      dmas = <&edma0 0 VF610_EDMA_MUXID0_SAI2_TX>,
+		   <&edma0 0 VF610_EDMA_MUXID0_SAI2_RX>;
+	      big-endian;
+	      lsb-first;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/hdmi.txt b/kernel/Documentation/devicetree/bindings/sound/hdmi.txt
new file mode 100644
index 000000000..31af7bca3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/hdmi.txt
@@ -0,0 +1,17 @@
+Device-Tree bindings for dummy HDMI codec
+
+Required properties:
+	- compatible: should be "linux,hdmi-audio".
+
+CODEC output pins:
+  * TX
+
+CODEC input pins:
+  * RX
+
+Example node:
+
+	hdmi_audio: hdmi_audio@0 {
+		compatible = "linux,hdmi-audio";
+		status = "okay";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt b/kernel/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt
new file mode 100644
index 000000000..07b68ab20
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt
@@ -0,0 +1,60 @@
+Freescale i.MX audio complex with ES8328 codec
+
+Required properties:
+- compatible       : "fsl,imx-audio-es8328"
+- model            : The user-visible name of this sound complex
+- ssi-controller   : The phandle of the i.MX SSI controller
+- jack-gpio        : Optional GPIO for headphone jack
+- audio-amp-supply : Power regulator for speaker amps
+- audio-codec      : The phandle of the ES8328 audio codec
+- audio-routing    : A list of the connections between audio components.
+                     Each entry is a pair of strings, the first being the
+		     connection's sink, the second being the connection's
+		     source. Valid names could be power supplies, ES8328
+		     pins, and the jacks on the board:
+
+			Power supplies:
+			   * audio-amp
+
+			ES8328 pins:
+			   * LOUT1
+			   * LOUT2
+			   * ROUT1
+			   * ROUT2
+			   * LINPUT1
+			   * LINPUT2
+			   * RINPUT1
+			   * RINPUT2
+			   * Mic PGA
+
+			Board connectors:
+			   * Headphone
+			   * Speaker
+			   * Mic Jack
+- mux-int-port     : The internal port of the i.MX audio muxer (AUDMUX)
+- mux-ext-port     : The external port of the i.MX audio muxer (AUDMIX)
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+sound {
+	compatible = "fsl,imx-audio-es8328";
+	model = "imx-audio-es8328";
+	ssi-controller = <&ssi1>;
+	audio-codec = <&codec>;
+	jack-gpio = <&gpio5 15 0>;
+	audio-amp-supply = <&reg_audio_amp>;
+	audio-routing =
+		"Speaker", "LOUT2",
+		"Speaker", "ROUT2",
+		"Speaker", "audio-amp",
+		"Headphone", "ROUT1",
+		"Headphone", "LOUT1",
+		"LINPUT1", "Mic Jack",
+		"RINPUT1", "Mic Jack",
+		"Mic Jack", "Mic Bias";
+	mux-int-port = <1>;
+	mux-ext-port = <3>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt b/kernel/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt
new file mode 100644
index 000000000..2f89db88f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt
@@ -0,0 +1,56 @@
+Freescale i.MX audio complex with SGTL5000 codec
+
+Required properties:
+
+  - compatible		: "fsl,imx-audio-sgtl5000"
+
+  - model		: The user-visible name of this sound complex
+
+  - ssi-controller	: The phandle of the i.MX SSI controller
+
+  - audio-codec		: The phandle of the SGTL5000 audio codec
+
+  - audio-routing	: A list of the connections between audio components.
+			  Each entry is a pair of strings, the first being the
+			  connection's sink, the second being the connection's
+			  source. Valid names could be power supplies, SGTL5000
+			  pins, and the jacks on the board:
+
+			  Power supplies:
+			   * Mic Bias
+
+			  SGTL5000 pins:
+			   * MIC_IN
+			   * LINE_IN
+			   * HP_OUT
+			   * LINE_OUT
+
+			  Board connectors:
+			   * Mic Jack
+			   * Line In Jack
+			   * Headphone Jack
+			   * Line Out Jack
+			   * Ext Spk
+
+  - mux-int-port	: The internal port of the i.MX audio muxer (AUDMUX)
+
+  - mux-ext-port	: The external port of the i.MX audio muxer
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+sound {
+	compatible = "fsl,imx51-babbage-sgtl5000",
+		     "fsl,imx-audio-sgtl5000";
+	model = "imx51-babbage-sgtl5000";
+	ssi-controller = <&ssi1>;
+	audio-codec = <&sgtl5000>;
+	audio-routing =
+		"MIC_IN", "Mic Jack",
+		"Mic Jack", "Mic Bias",
+		"Headphone Jack", "HP_OUT";
+	mux-int-port = <1>;
+	mux-ext-port = <3>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt b/kernel/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt
new file mode 100644
index 000000000..da84a442c
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt
@@ -0,0 +1,36 @@
+Freescale i.MX audio complex with S/PDIF transceiver
+
+Required properties:
+
+  - compatible		: "fsl,imx-audio-spdif"
+
+  - model		: The user-visible name of this sound complex
+
+  - spdif-controller	: The phandle of the i.MX S/PDIF controller
+
+
+Optional properties:
+
+  - spdif-out		: This is a boolean property. If present, the
+			  transmitting function of S/PDIF will be enabled,
+			  indicating there's a physical S/PDIF out connector
+			  or jack on the board or it's connecting to some
+			  other IP block, such as an HDMI encoder or
+			  display-controller.
+
+  - spdif-in		: This is a boolean property. If present, the receiving
+			  function of S/PDIF will be enabled, indicating there
+			  is a physical S/PDIF in connector/jack on the board.
+
+* Note: At least one of these two properties should be set in the DT binding.
+
+
+Example:
+
+sound-spdif {
+	compatible = "fsl,imx-audio-spdif";
+	model = "imx-spdif";
+	spdif-controller = <&spdif>;
+	spdif-out;
+	spdif-in;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/kernel/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt
new file mode 100644
index 000000000..acea71bee
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt
@@ -0,0 +1,53 @@
+Freescale i.MX audio complex with WM8962 codec
+
+Required properties:
+
+  - compatible		: "fsl,imx-audio-wm8962"
+
+  - model		: The user-visible name of this sound complex
+
+  - ssi-controller	: The phandle of the i.MX SSI controller
+
+  - audio-codec		: The phandle of the WM8962 audio codec
+
+  - audio-routing	: A list of the connections between audio components.
+			  Each entry is a pair of strings, the first being the
+			  connection's sink, the second being the connection's
+			  source. Valid names could be power supplies, WM8962
+			  pins, and the jacks on the board:
+
+			  Power supplies:
+			   * Mic Bias
+
+			  Board connectors:
+			   * Mic Jack
+			   * Headphone Jack
+			   * Ext Spk
+
+  - mux-int-port	: The internal port of the i.MX audio muxer (AUDMUX)
+
+  - mux-ext-port	: The external port of the i.MX audio muxer
+
+Note: The AUDMUX port numbering should start at 1, which is consistent with
+hardware manual.
+
+Example:
+
+sound {
+	compatible = "fsl,imx6q-sabresd-wm8962",
+		     "fsl,imx-audio-wm8962";
+	model = "wm8962-audio";
+	ssi-controller = <&ssi2>;
+	audio-codec = <&codec>;
+		audio-routing =
+		"Headphone Jack", "HPOUTL",
+		"Headphone Jack", "HPOUTR",
+		"Ext Spk", "SPKOUTL",
+		"Ext Spk", "SPKOUTR",
+		"MICBIAS", "AMIC",
+		"IN3R", "MICBIAS",
+		"DMIC", "MICBIAS",
+		"DMICDAT", "DMIC";
+	mux-int-port = <2>;
+	mux-ext-port = <3>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/imx-audmux.txt b/kernel/Documentation/devicetree/bindings/sound/imx-audmux.txt
new file mode 100644
index 000000000..b30a737e2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/imx-audmux.txt
@@ -0,0 +1,28 @@
+Freescale Digital Audio Mux (AUDMUX) device
+
+Required properties:
+
+  - compatible		: "fsl,imx21-audmux" for AUDMUX version firstly used
+			  on i.MX21, or "fsl,imx31-audmux" for the version
+			  firstly used on i.MX31.
+
+  - reg			: Should contain AUDMUX registers location and length.
+
+An initial configuration can be setup using child nodes.
+
+Required properties of optional child nodes:
+
+  - fsl,audmux-port	: Integer of the audmux port that is configured by this
+			  child node.
+
+  - fsl,port-config	: List of configuration options for the specific port.
+			  For imx31-audmux and above, it is a list of tuples
+			  <ptcr pdcr>. For imx21-audmux it is a list of pcr
+			  values.
+
+Example:
+
+audmux@021d8000 {
+	compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
+	reg = <0x021d8000 0x4000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt
new file mode 100644
index 000000000..b623d5000
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt
@@ -0,0 +1,23 @@
+Ingenic JZ4740 I2S controller
+
+Required properties:
+- compatible : "ingenic,jz4740-i2s" or "ingenic,jz4780-i2s"
+- reg : I2S registers location and length
+- clocks : AIC and I2S PLL clock specifiers.
+- clock-names: "aic" and "i2s"
+- dmas: DMA controller phandle and DMA request line for I2S Tx and Rx channels
+- dma-names: Must be "tx" and "rx"
+
+Example:
+
+i2s: i2s@10020000 {
+	compatible = "ingenic,jz4740-i2s";
+	reg = <0x10020000 0x94>;
+
+	clocks = <&cgu JZ4740_CLK_AIC>, <&cgu JZ4740_CLK_I2SPLL>;
+	clock-names = "aic", "i2s";
+
+	dmas = <&dma 2>, <&dma 3>;
+	dma-names = "tx", "rx";
+
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/max98090.txt b/kernel/Documentation/devicetree/bindings/sound/max98090.txt
new file mode 100644
index 000000000..aa802a274
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/max98090.txt
@@ -0,0 +1,51 @@
+MAX98090 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "maxim,max98090" or "maxim,max98091".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+- clocks: The phandle of the master clock to the CODEC
+
+- clock-names: Should be "mclk"
+
+- maxim,dmic-freq: Frequency at which to clock DMIC
+
+Pins on the device (for linking into audio routes):
+
+  * MIC1
+  * MIC2
+  * DMICL
+  * DMICR
+  * IN1
+  * IN2
+  * IN3
+  * IN4
+  * IN5
+  * IN6
+  * IN12
+  * IN34
+  * IN56
+  * HPL
+  * HPR
+  * SPKL
+  * SPKR
+  * RCVL
+  * RCVR
+  * MICBIAS
+
+Example:
+
+audio-codec@10 {
+	compatible = "maxim,max98090";
+	reg = <0x10>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/max98095.txt b/kernel/Documentation/devicetree/bindings/sound/max98095.txt
new file mode 100644
index 000000000..318a4c82f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/max98095.txt
@@ -0,0 +1,22 @@
+MAX98095 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "maxim,max98095".
+
+- reg : The I2C address of the device.
+
+Optional properties:
+
+- clocks: The phandle of the master clock to the CODEC
+
+- clock-names: Should be "mclk"
+
+Example:
+
+max98095: codec@11 {
+	compatible = "maxim,max98095";
+	reg = <0x11>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/max98357a.txt b/kernel/Documentation/devicetree/bindings/sound/max98357a.txt
new file mode 100644
index 000000000..a7a149a23
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/max98357a.txt
@@ -0,0 +1,14 @@
+Maxim MAX98357A audio DAC
+
+This node models the Maxim MAX98357A DAC.
+
+Required properties:
+- compatible   : "maxim,max98357a"
+- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin
+
+Example:
+
+max98357a {
+	compatible = "maxim,max98357a";
+	sdmode-gpios = <&qcom_pinmux 25 0>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/max98925.txt b/kernel/Documentation/devicetree/bindings/sound/max98925.txt
new file mode 100644
index 000000000..27be63e2a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/max98925.txt
@@ -0,0 +1,22 @@
+max98925 audio CODEC
+
+This device supports I2C.
+
+Required properties:
+
+  - compatible : "maxim,max98925"
+
+  - vmon-slot-no : slot number used to send voltage information
+
+  - imon-slot-no : slot number used to send current information
+
+  - reg : the I2C address of the device for I2C
+
+Example:
+
+codec: max98925@1a {
+	compatible = "maxim,max98925";
+	vmon-slot-no = <0>;
+	imon-slot-no = <2>;
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt b/kernel/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt
new file mode 100644
index 000000000..74c9ba6c2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt
@@ -0,0 +1,28 @@
+Marvell PXA SSP CPU DAI bindings
+
+Required properties:
+
+	compatible	Must be "mrvl,pxa-ssp-dai"
+	port		A phandle reference to a PXA ssp upstream device
+
+Example:
+
+	/* upstream device */
+
+	ssp0: ssp@41000000 {
+		compatible = "mrvl,pxa3xx-ssp";
+		reg = <0x41000000 0x40>;
+		interrupts = <24>;
+		clock-names = "pxa27x-ssp.0";
+		dmas = <&dma 13
+			&dma 14>;
+		dma-names = "rx", "tx";
+	};
+
+	/* DAI as user */
+
+	ssp_dai0: ssp_dai@0 {
+		compatible = "mrvl,pxa-ssp-dai";
+		port = <&ssp0>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/mrvl,pxa2xx-pcm.txt b/kernel/Documentation/devicetree/bindings/sound/mrvl,pxa2xx-pcm.txt
new file mode 100644
index 000000000..551fbb834
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mrvl,pxa2xx-pcm.txt
@@ -0,0 +1,15 @@
+DT bindings for ARM PXA2xx PCM platform driver
+
+This is just a dummy driver that registers the PXA ASoC platform driver.
+It does not have any resources assigned.
+
+Required properties:
+
+	- compatible		'mrvl,pxa-pcm-audio'
+
+Example:
+
+	pxa_pcm_audio: snd_soc_pxa_audio {
+		compatible = "mrvl,pxa-pcm-audio";
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/mvebu-audio.txt b/kernel/Documentation/devicetree/bindings/sound/mvebu-audio.txt
new file mode 100644
index 000000000..cb8c07c81
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mvebu-audio.txt
@@ -0,0 +1,34 @@
+* mvebu (Kirkwood, Dove, Armada 370) audio controller
+
+Required properties:
+
+- compatible:
+  "marvell,kirkwood-audio" for Kirkwood platforms
+  "marvell,dove-audio" for Dove platforms
+  "marvell,armada370-audio" for Armada 370 platforms
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts:
+  with "marvell,kirkwood-audio", the audio interrupt
+  with "marvell,dove-audio", a list of two interrupts, the first for
+  the data flow, and the second for errors.
+
+- clocks: one or two phandles.
+  The first one is mandatory and defines the internal clock.
+  The second one is optional and defines an external clock.
+
+- clock-names: names associated to the clocks:
+	"internal" for the internal clock
+	"extclk" for the external clock
+
+Example:
+
+i2s1: audio-controller@b4000 {
+	compatible = "marvell,dove-audio";
+	reg = <0xb4000 0x2210>;
+	interrupts = <21>, <22>;
+	clocks = <&gate_clk 13>;
+	clock-names = "internal";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt b/kernel/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt
new file mode 100644
index 000000000..601c518ed
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mxs-audio-sgtl5000.txt
@@ -0,0 +1,17 @@
+* Freescale MXS audio complex with SGTL5000 codec
+
+Required properties:
+- compatible: "fsl,mxs-audio-sgtl5000"
+- model: The user-visible name of this sound complex
+- saif-controllers: The phandle list of the MXS SAIF controller
+- audio-codec: The phandle of the SGTL5000 audio codec
+
+Example:
+
+sound {
+	compatible = "fsl,imx28-evk-sgtl5000",
+		     "fsl,mxs-audio-sgtl5000";
+	model = "imx28-evk-sgtl5000";
+	saif-controllers = <&saif0 &saif1>;
+	audio-codec = <&sgtl5000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/mxs-saif.txt b/kernel/Documentation/devicetree/bindings/sound/mxs-saif.txt
new file mode 100644
index 000000000..7ba07a118
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/mxs-saif.txt
@@ -0,0 +1,41 @@
+* Freescale MXS Serial Audio Interface (SAIF)
+
+Required properties:
+- compatible: Should be "fsl,<chip>-saif"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR interrupt number
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SAIF DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
+
+Optional properties:
+- fsl,saif-master: phandle to the master SAIF.  It's only required for
+  the slave SAIF.
+
+Note: Each SAIF controller should have an alias correctly numbered
+in "aliases" node.
+
+Example:
+
+aliases {
+	saif0 = &saif0;
+	saif1 = &saif1;
+};
+
+saif0: saif@80042000 {
+	compatible = "fsl,imx28-saif";
+	reg = <0x80042000 2000>;
+	interrupts = <59>;
+	dmas = <&dma_apbx 4>;
+	dma-names = "rx-tx";
+};
+
+saif1: saif@80046000 {
+	compatible = "fsl,imx28-saif";
+	reg = <0x80046000 2000>;
+	interrupts = <58>;
+	dmas = <&dma_apbx 5>;
+	dma-names = "rx-tx";
+	fsl,saif-master = <&saif0>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nokia,rx51.txt b/kernel/Documentation/devicetree/bindings/sound/nokia,rx51.txt
new file mode 100644
index 000000000..72f93d996
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nokia,rx51.txt
@@ -0,0 +1,27 @@
+* Nokia N900 audio setup
+
+Required properties:
+- compatible: Should contain "nokia,n900-audio"
+- nokia,cpu-dai: phandle for the McBSP node
+- nokia,audio-codec: phandles for the main TLV320AIC3X node and the
+                     auxiliary TLV320AIC3X node (in this order)
+- nokia,headphone-amplifier: phandle for the TPA6130A2 node
+- tvout-selection-gpios: GPIO for tvout selection
+- jack-detection-gpios: GPIO for jack detection
+- eci-switch-gpios: GPIO for ECI (Enhancement Control Interface) switch
+- speaker-amplifier-gpios: GPIO for speaker amplifier
+
+Example:
+
+sound {
+	compatible = "nokia,n900-audio";
+
+	nokia,cpu-dai = <&mcbsp2>;
+	nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
+	nokia,headphone-amplifier = <&tpa6130a2>;
+
+	tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
+	jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
+	eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
+	speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt
new file mode 100644
index 000000000..57f40f934
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt
@@ -0,0 +1,48 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-alc5632"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the ALC5632's pins as documented in the binding for the device
+  and:
+
+  * Headset Stereophone
+  * Int Spk
+  * Headset Mic
+  * Digital Mic
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller
+- nvidia,audio-codec : The phandle of the ALC5632 audio codec
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-alc5632-paz00",
+				 "nvidia,tegra-audio-alc5632";
+
+	nvidia,model = "Compal PAZ00";
+
+	nvidia,audio-routing =
+				"Int Spk", "SPK_OUTP",
+				"Int Spk", "SPK_OUTN",
+				"Headset Mic","MICBIAS1",
+				"MIC1_N", "Headset Mic",
+				"MIC1_P", "Headset Mic",
+				"Headset Stereophone", "HP_OUT_R",
+				"Headset Stereophone", "HP_OUT_L";
+
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&alc5632>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt
new file mode 100644
index 000000000..c3495beba
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt
@@ -0,0 +1,53 @@
+NVIDIA Tegra audio complex, with MAX98090 CODEC
+
+Required properties:
+- compatible : "nvidia,tegra-audio-max98090"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the MAX98090's pins (as documented in its binding), and the jacks
+  on the board:
+
+  * Headphones
+  * Speakers
+  * Mic Jack
+  * Int Mic
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's
+  connected to the CODEC.
+- nvidia,audio-codec : The phandle of the MAX98090 audio codec.
+
+Optional properties:
+- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
+- nvidia,mic-det-gpios : The GPIO that detect microphones are plugged in
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-max98090-venice2",
+		     "nvidia,tegra-audio-max98090";
+	nvidia,model = "NVIDIA Tegra Venice2";
+
+	nvidia,audio-routing =
+		"Headphones", "HPR",
+		"Headphones", "HPL",
+		"Speakers", "SPKR",
+		"Speakers", "SPKL",
+		"Mic Jack", "MICBIAS",
+		"IN34", "Mic Jack";
+
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&acodec>;
+
+	clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
+		 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+		 <&tegra_car TEGRA124_CLK_EXTERN1>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt
new file mode 100644
index 000000000..7788808dc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt
@@ -0,0 +1,52 @@
+NVIDIA Tegra audio complex, with RT5640 CODEC
+
+Required properties:
+- compatible : "nvidia,tegra-audio-rt5640"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the RT5640's pins (as documented in its binding), and the jacks
+  on the board:
+
+  * Headphones
+  * Speakers
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's
+  connected to the CODEC.
+- nvidia,audio-codec : The phandle of the RT5640 audio codec. This binding
+  assumes that AIF1 on the CODEC is connected to Tegra.
+
+Optional properties:
+- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-rt5640-dalmore",
+			"nvidia,tegra-audio-rt5640";
+	nvidia,model = "NVIDIA Tegra Dalmore";
+
+	nvidia,audio-routing =
+		"Headphones", "HPOR",
+		"Headphones", "HPOL",
+		"Speakers", "SPORP",
+		"Speakers", "SPORN",
+		"Speakers", "SPOLP",
+		"Speakers", "SPOLN";
+
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&rt5640>;
+
+	nvidia,hp-det-gpios = <&gpio 143 0>; /* GPIO PR7 */
+
+	clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt
new file mode 100644
index 000000000..a4589cda2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5677.txt
@@ -0,0 +1,67 @@
+NVIDIA Tegra audio complex, with RT5677 CODEC
+
+Required properties:
+- compatible : "nvidia,tegra-audio-rt5677"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the RT5677's pins (as documented in its binding), and the jacks
+  on the board:
+
+  * Headphone
+  * Speaker
+  * Headset Mic
+  * Internal Mic 1
+  * Internal Mic 2
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's
+  connected to the CODEC.
+- nvidia,audio-codec : The phandle of the RT5677 audio codec. This binding
+  assumes that AIF1 on the CODEC is connected to Tegra.
+
+Optional properties:
+- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in
+- nvidia,hp-en-gpios : The GPIO that enables headphone amplifier
+- nvidia,mic-present-gpios: The GPIO that mic jack is plugged in
+- nvidia,dmic-clk-en-gpios : The GPIO that gates DMIC clock signal
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-rt5677-ryu",
+	        "nvidia,tegra-audio-rt5677";
+	nvidia,model = "NVIDIA Tegra Ryu";
+
+	nvidia,audio-routing =
+		"Headphone", "LOUT2",
+		"Headphone", "LOUT1",
+		"Headset Mic", "MICBIAS1",
+		"IN1P", "Headset Mic",
+		"IN1N", "Headset Mic",
+		"DMIC L1", "Internal Mic 1",
+		"DMIC R1", "Internal Mic 1",
+		"DMIC L2", "Internal Mic 2",
+		"DMIC R2", "Internal Mic 2",
+		"Speaker", "PDM1L",
+		"Speaker", "PDM1R";
+
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&rt5677>;
+
+	nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
+	nvidia,mic-present-gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>;
+	nvidia,hp-en-gpios = <&rt5677 1 GPIO_ACTIVE_HIGH>;
+	nvidia,dmic-clk-en-gpios = <&rt5677 2 GPIO_ACTIVE_HIGH>;
+
+	clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
+	         <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+	         <&tegra_car TEGRA124_CLK_EXTERN1>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt
new file mode 100644
index 000000000..ef1fe7358
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt
@@ -0,0 +1,21 @@
+NVIDIA Tegra audio complex for TrimSlice
+
+Required properties:
+- compatible : "nvidia,tegra-audio-trimslice"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-trimslice";
+	nvidia,i2s-controller = <&tegra_i2s1>;
+	nvidia,audio-codec = <&codec>;
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt
new file mode 100644
index 000000000..96f6a57dd
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt
@@ -0,0 +1,40 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8753"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM8753's pins as documented in the binding for the WM8753,
+  and the jacks on the board:
+
+  * Headphone Jack
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8753 audio codec
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm8753-whistler",
+		     "nvidia,tegra-audio-wm8753"
+	nvidia,model = "tegra-wm8753-harmony";
+
+	nvidia,audio-routing =
+		"Headphone Jack", "LOUT1",
+		"Headphone Jack", "ROUT1";
+
+	nvidia,i2s-controller = <&i2s1>;
+	nvidia,audio-codec = <&wm8753>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt
new file mode 100644
index 000000000..b795d2828
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt
@@ -0,0 +1,60 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm8903"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM8903's pins (documented in the WM8903 binding document),
+  and the jacks on the board:
+
+  * Headphone Jack
+  * Int Spk
+  * Mic Jack
+
+- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
+- nvidia,audio-codec : The phandle of the WM8903 audio codec
+
+Optional properties:
+- nvidia,spkr-en-gpios : The GPIO that enables the speakers
+- nvidia,hp-mute-gpios : The GPIO that mutes the headphones
+- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in
+- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone
+- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm8903-harmony",
+		     "nvidia,tegra-audio-wm8903"
+	nvidia,model = "tegra-wm8903-harmony";
+
+	nvidia,audio-routing =
+		"Headphone Jack", "HPOUTR",
+		"Headphone Jack", "HPOUTL",
+		"Int Spk", "ROP",
+		"Int Spk", "RON",
+		"Int Spk", "LOP",
+		"Int Spk", "LON",
+		"Mic Jack", "MICBIAS",
+		"IN1L", "Mic Jack";
+
+	nvidia,i2s-controller = <&i2s1>;
+	nvidia,audio-codec = <&wm8903>;
+
+	nvidia,spkr-en-gpios = <&codec 2 0>;
+	nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+	nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+	nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt
new file mode 100644
index 000000000..436f6cd9d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt
@@ -0,0 +1,60 @@
+NVIDIA Tegra audio complex
+
+Required properties:
+- compatible : "nvidia,tegra-audio-wm9712"
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - pll_a
+  - pll_a_out0
+  - mclk (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
+- nvidia,model : The user-visible name of this sound complex.
+- nvidia,audio-routing : A list of the connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source. Valid names for sources and
+  sinks are the WM9712's pins, and the jacks on the board:
+
+  WM9712 pins:
+
+  * MONOOUT
+  * HPOUTL
+  * HPOUTR
+  * LOUT2
+  * ROUT2
+  * OUT3
+  * LINEINL
+  * LINEINR
+  * PHONE
+  * PCBEEP
+  * MIC1
+  * MIC2
+  * Mic Bias
+
+  Board connectors:
+
+  * Headphone
+  * LineIn
+  * Mic
+
+- nvidia,ac97-controller : The phandle of the Tegra AC97 controller
+
+
+Example:
+
+sound {
+	compatible = "nvidia,tegra-audio-wm9712-colibri_t20",
+		         "nvidia,tegra-audio-wm9712";
+	nvidia,model = "Toradex Colibri T20";
+
+	nvidia,audio-routing =
+		"Headphone", "HPOUTL",
+		"Headphone", "HPOUTR",
+		"LineIn", "LINEINL",
+		"LineIn", "LINEINR",
+		"Mic", "MIC1";
+
+	nvidia,ac97-controller = <&ac97>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt
new file mode 100644
index 000000000..eaf00102d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-ac97.txt
@@ -0,0 +1,36 @@
+NVIDIA Tegra 20 AC97 controller
+
+Required properties:
+- compatible : "nvidia,tegra20-ac97"
+- reg : Should contain AC97 controller registers location and length
+- interrupts : Should contain AC97 interrupt
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - ac97
+- dmas : Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+  - rx
+  - tx
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- nvidia,codec-reset-gpio : The Tegra GPIO controller's phandle and the number
+  of the GPIO used to reset the external AC97 codec
+- nvidia,codec-sync-gpio : The Tegra GPIO controller's phandle and the number
+  of the GPIO corresponding with the AC97 DAP _FS line
+
+Example:
+
+ac97@70002000 {
+	compatible = "nvidia,tegra20-ac97";
+	reg = <0x70002000 0x200>;
+	interrupts = <0 81 0x04>;
+	nvidia,codec-reset-gpio = <&gpio 170 0>;
+	nvidia,codec-sync-gpio = <&gpio 120 0>;
+	clocks = <&tegra_car 3>;
+	resets = <&tegra_car 3>;
+	reset-names = "ac97";
+	dmas = <&apbdma 12>, <&apbdma 12>;
+	dma-names = "rx", "tx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt
new file mode 100644
index 000000000..6de3a7ee4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt
@@ -0,0 +1,12 @@
+NVIDIA Tegra 20 DAS (Digital Audio Switch) controller
+
+Required properties:
+- compatible : "nvidia,tegra20-das"
+- reg : Should contain DAS registers location and length
+
+Example:
+
+das@70000c00 {
+	compatible = "nvidia,tegra20-das";
+	reg = <0x70000c00 0x80>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt
new file mode 100644
index 000000000..dc30c6bfb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt
@@ -0,0 +1,30 @@
+NVIDIA Tegra 20 I2S controller
+
+Required properties:
+- compatible : "nvidia,tegra20-i2s"
+- reg : Should contain I2S registers location and length
+- interrupts : Should contain I2S interrupt
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - i2s
+- dmas : Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+  - rx
+  - tx
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+
+Example:
+
+i2s@70002800 {
+	compatible = "nvidia,tegra20-i2s";
+	reg = <0x70002800 0x200>;
+	interrupts = < 45 >;
+	clocks = <&tegra_car 11>;
+	resets = <&tegra_car 11>;
+	reset-names = "i2s";
+	dmas = <&apbdma 21>, <&apbdma 21>;
+	dma-names = "rx", "tx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt
new file mode 100644
index 000000000..0e9a1895d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-ahub.txt
@@ -0,0 +1,88 @@
+NVIDIA Tegra30 AHUB (Audio Hub)
+
+Required properties:
+- compatible : For Tegra30, must contain "nvidia,tegra30-ahub".  For Tegra114,
+  must contain "nvidia,tegra114-ahub".  For Tegra124, must contain
+  "nvidia,tegra124-ahub".  Otherwise, must contain "nvidia,<chip>-ahub",
+  plus at least one of the above, where <chip> is tegra132.
+- reg : Should contain the register physical address and length for each of
+  the AHUB's register blocks.
+  - Tegra30 requires 2 entries, for the APBIF and AHUB/AUDIO register blocks.
+  - Tegra114 requires an additional entry, for the APBIF2 register block.
+- interrupts : Should contain AHUB interrupt
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - d_audio
+  - apbif
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  Tegra30 and later:
+  - d_audio
+  - apbif
+  - i2s0
+  - i2s1
+  - i2s2
+  - i2s3
+  - i2s4
+  - dam0
+  - dam1
+  - dam2
+  - spdif
+  Tegra114 and later additionally require:
+  - amx
+  - adx
+  Tegra124 and later additionally require:
+  - amx1
+  - adx1
+  - afc0
+  - afc1
+  - afc2
+  - afc3
+  - afc4
+  - afc5
+- ranges : The bus address mapping for the configlink register bus.
+  Can be empty since the mapping is 1:1.
+- dmas : Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+  - rx0 .. rx<n>
+  - tx0 .. tx<n>
+  ... where n is:
+  Tegra30: 3
+  Tegra114, Tegra124: 9
+- #address-cells : For the configlink bus. Should be <1>;
+- #size-cells : For the configlink bus. Should be <1>.
+
+AHUB client modules need to specify the IDs of their CIFs (Client InterFaces).
+For RX CIFs, the numbers indicate the register number within AHUB routing
+register space (APBIF 0..3 RX, I2S 0..5 RX, DAM 0..2 RX 0..1, SPDIF RX 0..1).
+For TX CIFs, the numbers indicate the bit position within the AHUB routing
+registers (APBIF 0..3 TX, I2S 0..5 TX, DAM 0..2 TX, SPDIF TX 0..1).
+
+Example:
+
+ahub@70080000 {
+	compatible = "nvidia,tegra30-ahub";
+	reg = <0x70080000 0x200 0x70080200 0x100>;
+	interrupts = < 0 103 0x04 >;
+	nvidia,dma-request-selector = <&apbdma 1>;
+	clocks = <&tegra_car 106>, <&tegra_car 107>;
+	clock-names = "d_audio", "apbif";
+	resets = <&tegra_car 106>, <&tegra_car 107>, <&tegra_car 30>,
+		<&tegra_car 11>, <&tegra_car 18>, <&tegra_car 101>,
+		<&tegra_car 102>, <&tegra_car 108>, <&tegra_car 109>,
+		<&tegra_car 110>, <&tegra_car 10>;
+	reset-names = "d_audio", "apbif", "i2s0", "i2s1", "i2s2",
+		"i2s3", "i2s4", "dam0", "dam1", "dam2",
+		"spdif";
+	dmas = <&apbdma 1>, <&apbdma 1>;
+	       <&apbdma 2>, <&apbdma 2>;
+	       <&apbdma 3>, <&apbdma 3>;
+	       <&apbdma 4>, <&apbdma 4>;
+	dma-names = "rx0", "tx0", "rx1", "tx1", "rx2", "tx2", "rx3", "tx3";
+	ranges;
+	#address-cells = <1>;
+	#size-cells = <1>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt
new file mode 100644
index 000000000..13e2ef496
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt
@@ -0,0 +1,30 @@
+NVIDIA Tegra30 HDA controller
+
+Required properties:
+- compatible : For Tegra30, must contain "nvidia,tegra30-hda".  Otherwise,
+  must contain '"nvidia,<chip>-hda", "nvidia,tegra30-hda"', where <chip> is
+  tegra114, tegra124, or tegra132.
+- reg : Should contain the HDA registers location and length.
+- interrupts : The interrupt from the HDA controller.
+- clocks : Must contain an entry for each required entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi
+
+Example:
+
+hda@0,70030000 {
+	compatible = "nvidia,tegra124-hda", "nvidia,tegra30-hda";
+	reg = <0x0 0x70030000 0x0 0x10000>;
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA124_CLK_HDA>,
+		 <&tegra_car TEGRA124_CLK_HDA2HDMI>,
+		 <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>;
+	clock-names = "hda", "hda2hdmi", "hda2codec_2x";
+	resets = <&tegra_car 125>, /* hda */
+		 <&tegra_car 128>; /* hda2hdmi */
+		 <&tegra_car 111>, /* hda2codec_2x */
+	reset-names = "hda", "hda2hdmi", "hda2codec_2x";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt
new file mode 100644
index 000000000..38caa936f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/nvidia,tegra30-i2s.txt
@@ -0,0 +1,27 @@
+NVIDIA Tegra30 I2S controller
+
+Required properties:
+- compatible : For Tegra30, must contain "nvidia,tegra30-i2s".  For Tegra124,
+  must contain "nvidia,tegra124-i2s".  Otherwise, must contain
+  "nvidia,<chip>-i2s" plus at least one of the above, where <chip> is
+  tegra114 or tegra132.
+- reg : Should contain I2S registers location and length
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - i2s
+- nvidia,ahub-cif-ids : The list of AHUB CIF IDs for this port, rx (playback)
+  first, tx (capture) second. See nvidia,tegra30-ahub.txt for values.
+
+Example:
+
+i2s@70080300 {
+	compatible = "nvidia,tegra30-i2s";
+	reg = <0x70080300 0x100>;
+	nvidia,ahub-cif-ids = <4 4>;
+	clocks = <&tegra_car 11>;
+	resets = <&tegra_car 11>;
+	reset-names = "i2s";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt b/kernel/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt
new file mode 100644
index 000000000..fd40c852d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/omap-abe-twl6040.txt
@@ -0,0 +1,91 @@
+* Texas Instruments OMAP4+ and twl6040 based audio setups
+
+Required properties:
+- compatible: "ti,abe-twl6040"
+- ti,model: Name of the sound card ( for example "SDP4430")
+- ti,mclk-freq: MCLK frequency for HPPLL operation
+- ti,mcpdm: phandle for the McPDM node
+- ti,twl6040: phandle for the twl6040 core node
+- ti,audio-routing: List of connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source.
+
+Optional properties:
+- ti,dmic: phandle for the OMAP dmic node if the machine have it connected
+- ti,jack_detection: Need to be present if the board capable to detect jack
+  insertion, removal.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Earphone Spk
+ * Ext Spk
+ * Line Out
+ * Vibrator
+ * Headset Mic
+ * Main Handset Mic
+ * Sub Handset Mic
+ * Line In
+ * Digital Mic
+
+twl6040 pins:
+ * HSOL
+ * HSOR
+ * EP
+ * HFL
+ * HFR
+ * AUXL
+ * AUXR
+ * VIBRAL
+ * VIBRAR
+ * HSMIC
+ * MAINMIC
+ * SUBMIC
+ * AFML
+ * AFMR
+
+ * Headset Mic Bias
+ * Main Mic Bias
+ * Digital Mic1 Bias
+ * Digital Mic2 Bias
+
+Digital mic pins:
+ * DMic
+
+Example:
+
+sound {
+	compatible = "ti,abe-twl6040";
+	ti,model = "SDP4430";
+
+	ti,jack-detection;
+	ti,mclk-freq = <38400000>;
+
+	ti,mcpdm = <&mcpdm>;
+	ti,dmic = <&dmic>;
+
+	ti,twl6040 = <&twl6040>;
+
+	/* Audio routing */
+	ti,audio-routing =
+		"Headset Stereophone", "HSOL",
+		"Headset Stereophone", "HSOR",
+		"Earphone Spk", "EP",
+		"Ext Spk", "HFL",
+		"Ext Spk", "HFR",
+		"Line Out", "AUXL",
+		"Line Out", "AUXR",
+		"Vibrator", "VIBRAL",
+		"Vibrator", "VIBRAR",
+		"HSMIC", "Headset Mic",
+		"Headset Mic", "Headset Mic Bias",
+		"MAINMIC", "Main Handset Mic",
+		"Main Handset Mic", "Main Mic Bias",
+		"SUBMIC", "Sub Handset Mic",
+		"Sub Handset Mic", "Main Mic Bias",
+		"AFML", "Line In",
+		"AFMR", "Line In",
+		"DMic", "Digital Mic",
+		"Digital Mic", "Digital Mic1 Bias";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/omap-dmic.txt b/kernel/Documentation/devicetree/bindings/sound/omap-dmic.txt
new file mode 100644
index 000000000..fd8105f18
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/omap-dmic.txt
@@ -0,0 +1,21 @@
+* Texas Instruments OMAP4+ Digital Microphone Module
+
+Required properties:
+- compatible: "ti,omap4-dmic"
+- reg: Register location and size as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- interrupts: Interrupt number for DMIC
+- interrupt-parent: The parent interrupt controller
+- ti,hwmods: Name of the hwmod associated with OMAP dmic IP
+
+Example:
+
+dmic: dmic@4012e000 {
+	compatible = "ti,omap4-dmic";
+	reg = <0x4012e000 0x7f>, /* MPU private access */
+	      <0x4902e000 0x7f>; /* L3 Interconnect */
+	interrupts = <0 114 0x4>;
+	interrupt-parent = <&gic>;
+	ti,hwmods = "dmic";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/omap-mcbsp.txt b/kernel/Documentation/devicetree/bindings/sound/omap-mcbsp.txt
new file mode 100644
index 000000000..17cce4490
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/omap-mcbsp.txt
@@ -0,0 +1,37 @@
+* Texas Instruments OMAP2+ McBSP module
+
+Required properties:
+- compatible: "ti,omap2420-mcbsp" for McBSP on OMAP2420
+	      "ti,omap2430-mcbsp" for McBSP on OMAP2430
+	      "ti,omap3-mcbsp" for McBSP on OMAP3
+	      "ti,omap4-mcbsp" for McBSP on OMAP4 and newer SoC
+- reg: Register location and size, for OMAP4+ as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- reg-names: Array of strings associated with the address space
+- interrupts: Interrupt numbers for the McBSP port, as an array in case the
+	      McBSP IP have more interrupt lines:
+	<OCP compliant irq>,
+	<TX irq>,
+	<RX irq>;
+- interrupt-names: Array of strings associated with the interrupt numbers
+- interrupt-parent: The parent interrupt controller
+- ti,buffer-size: Size of the FIFO on the port (OMAP2430 and newer SoC)
+- ti,hwmods: Name of the hwmod associated to the McBSP port
+
+Example:
+
+mcbsp2: mcbsp@49022000 {
+	compatible = "ti,omap3-mcbsp";
+	reg = <0x49022000 0xff>,
+	      <0x49028000 0xff>;
+	reg-names = "mpu", "sidetone";
+	interrupts = <0 17 0x4>, /* OCP compliant interrupt */
+		     <0 62 0x4>, /* TX interrupt */
+		     <0 63 0x4>, /* RX interrupt */
+		     <0 4 0x4>;  /* Sidetone */
+	interrupt-names = "common", "tx", "rx", "sidetone";
+	interrupt-parent = <&intc>;
+	ti,buffer-size = <1280>;
+	ti,hwmods = "mcbsp2";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/kernel/Documentation/devicetree/bindings/sound/omap-mcpdm.txt
new file mode 100644
index 000000000..0741dff04
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/omap-mcpdm.txt
@@ -0,0 +1,21 @@
+* Texas Instruments OMAP4+ McPDM
+
+Required properties:
+- compatible: "ti,omap4-mcpdm"
+- reg: Register location and size as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- interrupts: Interrupt number for McPDM
+- interrupt-parent: The parent interrupt controller
+- ti,hwmods: Name of the hwmod associated to the McPDM
+
+Example:
+
+mcpdm: mcpdm@40132000 {
+	compatible = "ti,omap4-mcpdm";
+	reg = <0x40132000 0x7f>, /* MPU private access */
+	      <0x49032000 0x7f>; /* L3 Interconnect */
+	interrupts = <0 112 0x4>;
+	interrupt-parent = <&gic>;
+	ti,hwmods = "mcpdm";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/kernel/Documentation/devicetree/bindings/sound/omap-twl4030.txt
new file mode 100644
index 000000000..f6a715e4e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/omap-twl4030.txt
@@ -0,0 +1,62 @@
+* Texas Instruments SoC with twl4030 based audio setups
+
+Required properties:
+- compatible: "ti,omap-twl4030"
+- ti,model: Name of the sound card (for example "omap3beagle")
+- ti,mcbsp: phandle for the McBSP node
+
+Optional properties:
+- ti,codec: phandle for the twl4030 audio node
+- ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl
+- ti, jack-det-gpio: Jack detect GPIO
+- ti,audio-routing: List of connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source.
+  If the routing is not provided all possible connection will be available
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Earpiece Spk
+ * Handsfree Spk
+ * Ext Spk
+ * Main Mic
+ * Sub Mic
+ * Headset Mic
+ * Carkit Mic
+ * Digital0 Mic
+ * Digital1 Mic
+ * Line In
+
+twl4030 pins:
+ * HSOL
+ * HSOR
+ * EARPIECE
+ * HFL
+ * HFR
+ * PREDRIVEL
+ * PREDRIVER
+ * CARKITL
+ * CARKITR
+ * MAINMIC
+ * SUBMIC
+ * HSMIC
+ * DIGIMIC0
+ * DIGIMIC1
+ * CARKITMIC
+ * AUXL
+ * AUXR
+
+ * Headset Mic Bias
+ * Mic Bias 1 /* Used for Main Mic or Digimic0 */
+ * Mic Bias 2 /* Used for Sub Mic or Digimic1 */
+
+Example:
+
+sound {
+	compatible = "ti,omap-twl4030";
+	ti,model = "omap3beagle";
+
+	ti,mcbsp = <&mcbsp2>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/pcm1792a.txt b/kernel/Documentation/devicetree/bindings/sound/pcm1792a.txt
new file mode 100644
index 000000000..970ba1ed5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/pcm1792a.txt
@@ -0,0 +1,18 @@
+Texas Instruments pcm1792a DT bindings
+
+This driver supports the SPI bus.
+
+Required properties:
+
+ - compatible: "ti,pcm1792a"
+
+For required properties on SPI, please consult
+Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Examples:
+
+	codec_spi: 1792a@0 {
+		compatible = "ti,pcm1792a";
+		spi-max-frequency = <600000>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/pcm512x.txt b/kernel/Documentation/devicetree/bindings/sound/pcm512x.txt
new file mode 100644
index 000000000..3aae3b41b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/pcm512x.txt
@@ -0,0 +1,52 @@
+PCM512x audio CODECs
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : One of "ti,pcm5121", "ti,pcm5122", "ti,pcm5141" or
+                 "ti,pcm5142"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+  - AVDD-supply, DVDD-supply, and CPVDD-supply : power supplies for the
+    device, as covered in bindings/regulator/regulator.txt
+
+Optional properties:
+
+  - clocks : A clock specifier for the clock connected as SCLK.  If this
+    is absent the device will be configured to clock from BCLK.  If pll-in
+    and pll-out are specified in addition to a clock, the device is
+    configured to accept clock input on a specified gpio pin.
+
+  - pll-in, pll-out : gpio pins used to connect the pll using <1>
+    through <6>.  The device will be configured for clock input on the
+    given pll-in pin and PLL output on the given pll-out pin.  An
+    external connection from the pll-out pin to the SCLK pin is assumed.
+
+Examples:
+
+	pcm5122: pcm5122@4c {
+		compatible = "ti,pcm5122";
+		reg = <0x4c>;
+
+		AVDD-supply = <&reg_3v3_analog>;
+		DVDD-supply = <&reg_1v8>;
+		CPVDD-supply = <&reg_3v3>;
+	};
+
+
+	pcm5142: pcm5142@4c {
+		compatible = "ti,pcm5142";
+		reg = <0x4c>;
+
+		AVDD-supply = <&reg_3v3_analog>;
+		DVDD-supply = <&reg_1v8>;
+		CPVDD-supply = <&reg_3v3>;
+
+		clocks = <&sck>;
+		pll-in = <3>;
+		pll-out = <6>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt
new file mode 100644
index 000000000..e00732dac
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt
@@ -0,0 +1,43 @@
+* Qualcomm Technologies LPASS CPU DAI
+
+This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS).
+
+Required properties:
+
+- compatible		: "qcom,lpass-cpu"
+- clocks		: Must contain an entry for each entry in clock-names.
+- clock-names		: A list which must include the following entries:
+				* "ahbix-clk"
+				* "mi2s-osr-clk"
+				* "mi2s-bit-clk"
+- interrupts		: Must contain an entry for each entry in
+			  interrupt-names.
+- interrupt-names	: A list which must include the following entries:
+				* "lpass-irq-lpaif"
+- pinctrl-N		: One property must exist for each entry in
+			  pinctrl-names.  See ../pinctrl/pinctrl-bindings.txt
+			  for details of the property values.
+- pinctrl-names		: Must contain a "default" entry.
+- reg			: Must contain an address for each entry in reg-names.
+- reg-names		: A list which must include the following entries:
+				* "lpass-lpaif"
+
+Optional properties:
+
+- qcom,adsp		: Phandle for the audio DSP node
+
+Example:
+
+lpass@28100000 {
+	compatible = "qcom,lpass-cpu";
+	clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>;
+	clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk";
+	interrupts = <0 85 1>;
+	interrupt-names = "lpass-irq-lpaif";
+	pinctrl-names = "default", "idle";
+	pinctrl-0 = <&mi2s_default>;
+	pinctrl-1 = <&mi2s_idle>;
+	reg = <0x28100000 0x10000>;
+	reg-names = "lpass-lpaif";
+	qcom,adsp = <&adsp>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/kernel/Documentation/devicetree/bindings/sound/renesas,fsi.txt
new file mode 100644
index 000000000..0d0ab5110
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/renesas,fsi.txt
@@ -0,0 +1,31 @@
+Renesas FSI
+
+Required properties:
+- compatible			: "renesas,fsi2-<soctype>",
+				  "renesas,sh_fsi2" or "renesas,sh_fsi" as
+				  fallback.
+				  Examples with soctypes are:
+				    - "renesas,fsi2-r8a7740" (R-Mobile A1)
+				    - "renesas,fsi2-sh73a0" (SH-Mobile AG5)
+- reg				: Should contain the register physical address and length
+- interrupts			: Should contain FSI interrupt
+
+- fsia,spdif-connection		: FSI is connected by S/PDIF
+- fsia,stream-mode-support	: FSI supports 16bit stream mode.
+- fsia,use-internal-clock	: FSI uses internal clock when master mode.
+
+- fsib,spdif-connection		: same as fsia
+- fsib,stream-mode-support	: same as fsia
+- fsib,use-internal-clock	: same as fsia
+
+Example:
+
+sh_fsi2: sh_fsi2@0xec230000 {
+	compatible = "renesas,sh_fsi2";
+	reg = <0xec230000 0x400>;
+	interrupts = <0 146 0x4>;
+
+	fsia,spdif-connection;
+	fsia,stream-mode-support;
+	fsia,use-internal-clock;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
new file mode 100644
index 000000000..f316ce1f2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
@@ -0,0 +1,216 @@
+Renesas R-Car sound
+
+Required properties:
+- compatible			: "renesas,rcar_sound-<soctype>", fallbacks
+				  "renesas,rcar_sound-gen1" if generation1, and
+				  "renesas,rcar_sound-gen2" if generation2
+				  Examples with soctypes are:
+				    - "renesas,rcar_sound-r8a7790" (R-Car H2)
+				    - "renesas,rcar_sound-r8a7791" (R-Car M2-W)
+- reg				: Should contain the register physical address.
+				  required register is
+				   SRU/ADG/SSI      if generation1
+				   SRU/ADG/SSIU/SSI if generation2
+- rcar_sound,ssi		: Should contain SSI feature.
+				  The number of SSI subnode should be same as HW.
+				  see below for detail.
+- rcar_sound,src		: Should contain SRC feature.
+				  The number of SRC subnode should be same as HW.
+				  see below for detail.
+- rcar_sound,dvc		: Should contain DVC feature.
+				  The number of DVC subnode should be same as HW.
+				  see below for detail.
+- rcar_sound,dai		: DAI contents.
+				  The number of DAI subnode should be same as HW.
+				  see below for detail.
+
+SSI subnode properties:
+- interrupts			: Should contain SSI interrupt for PIO transfer
+- shared-pin			: if shared clock pin
+- pio-transfer			: use PIO transfer mode
+- no-busif			: BUSIF is not ussed when [mem -> SSI] via DMA case
+- dma				: Should contain Audio DMAC entry
+- dma-names			: SSI  case "rx"  (=playback), "tx"  (=capture)
+				  SSIU case "rxu" (=playback), "txu" (=capture)
+
+SRC subnode properties:
+- dma				: Should contain Audio DMAC entry
+- dma-names			: "rx" (=playback), "tx" (=capture)
+
+DVC subnode properties:
+- dma				: Should contain Audio DMAC entry
+- dma-names			: "tx" (=playback/capture)
+
+DAI subnode properties:
+- playback			: list of playback modules
+- capture			: list of capture  modules
+
+Example:
+
+rcar_sound: rcar_sound@ec500000 {
+	#sound-dai-cells = <1>;
+	compatible = "renesas,rcar_sound-r8a7791", "renesas,rcar_sound-gen2";
+	reg =	<0 0xec500000 0 0x1000>, /* SCU */
+		<0 0xec5a0000 0 0x100>,  /* ADG */
+		<0 0xec540000 0 0x1000>, /* SSIU */
+		<0 0xec541000 0 0x1280>, /* SSI */
+		<0 0xec740000 0 0x200>;  /* Audio DMAC peri peri*/
+	reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
+
+	clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>,
+		<&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>,
+		<&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>,
+		<&mstp10_clks R8A7790_CLK_SSI5>, <&mstp10_clks R8A7790_CLK_SSI4>,
+		<&mstp10_clks R8A7790_CLK_SSI3>, <&mstp10_clks R8A7790_CLK_SSI2>,
+		<&mstp10_clks R8A7790_CLK_SSI1>, <&mstp10_clks R8A7790_CLK_SSI0>,
+		<&mstp10_clks R8A7790_CLK_SCU_SRC9>, <&mstp10_clks R8A7790_CLK_SCU_SRC8>,
+		<&mstp10_clks R8A7790_CLK_SCU_SRC7>, <&mstp10_clks R8A7790_CLK_SCU_SRC6>,
+		<&mstp10_clks R8A7790_CLK_SCU_SRC5>, <&mstp10_clks R8A7790_CLK_SCU_SRC4>,
+		<&mstp10_clks R8A7790_CLK_SCU_SRC3>, <&mstp10_clks R8A7790_CLK_SCU_SRC2>,
+		<&mstp10_clks R8A7790_CLK_SCU_SRC1>, <&mstp10_clks R8A7790_CLK_SCU_SRC0>,
+		<&mstp10_clks R8A7790_CLK_SCU_DVC0>, <&mstp10_clks R8A7790_CLK_SCU_DVC1>,
+		<&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, <&m2_clk>;
+	clock-names = "ssi-all",
+			"ssi.9", "ssi.8", "ssi.7", "ssi.6", "ssi.5",
+			"ssi.4", "ssi.3", "ssi.2", "ssi.1", "ssi.0",
+			"src.9", "src.8", "src.7", "src.6", "src.5",
+			"src.4", "src.3", "src.2", "src.1", "src.0",
+			"dvc.0", "dvc.1",
+			"clk_a", "clk_b", "clk_c", "clk_i";
+
+	rcar_sound,dvc {
+		dvc0: dvc@0 {
+			dmas = <&audma0 0xbc>;
+			dma-names = "tx";
+		};
+		dvc1: dvc@1 {
+			dmas = <&audma0 0xbe>;
+			dma-names = "tx";
+		};
+	};
+
+	rcar_sound,src {
+		src0: src@0 {
+			interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x85>, <&audma1 0x9a>;
+			dma-names = "rx", "tx";
+		};
+		src1: src@1 {
+			interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x87>, <&audma1 0x9c>;
+			dma-names = "rx", "tx";
+		};
+		src2: src@2 {
+			interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x89>, <&audma1 0x9e>;
+			dma-names = "rx", "tx";
+		};
+		src3: src@3 {
+			interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x8b>, <&audma1 0xa0>;
+			dma-names = "rx", "tx";
+		};
+		src4: src@4 {
+			interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x8d>, <&audma1 0xb0>;
+			dma-names = "rx", "tx";
+		};
+		src5: src@5 {
+			interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x8f>, <&audma1 0xb2>;
+			dma-names = "rx", "tx";
+		};
+		src6: src@6 {
+			interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x91>, <&audma1 0xb4>;
+			dma-names = "rx", "tx";
+		};
+		src7: src@7 {
+			interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x93>, <&audma1 0xb6>;
+			dma-names = "rx", "tx";
+		};
+		src8: src@8 {
+			interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x95>, <&audma1 0xb8>;
+			dma-names = "rx", "tx";
+		};
+		src9: src@9 {
+			interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x97>, <&audma1 0xba>;
+			dma-names = "rx", "tx";
+		};
+	};
+
+	rcar_sound,ssi {
+		ssi0: ssi@0 {
+			interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi1: ssi@1 {
+			interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi2: ssi@2 {
+			interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi3: ssi@3 {
+			interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi4: ssi@4 {
+			interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi5: ssi@5 {
+			interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi6: ssi@6 {
+			interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi7: ssi@7 {
+			interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi8: ssi@8 {
+			interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+		ssi9: ssi@9 {
+			interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
+			dma-names = "rx", "tx", "rxu", "txu";
+		};
+	};
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi5 &src5>;
+			capture  = <&ssi6>;
+		};
+		dai1 {
+			playback = <&ssi3>;
+		};
+		dai2 {
+			capture  = <&ssi4>;
+		};
+		dai3 {
+			playback = <&ssi7>;
+		};
+		dai4 {
+			capture  = <&ssi8>;
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt
new file mode 100644
index 000000000..c64155027
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt
@@ -0,0 +1,67 @@
+Renesas Sampling Rate Convert Sound Card:
+
+Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC <-> codec.
+
+Required properties:
+
+- compatible				: "renesas,rsrc-card,<board>"
+					  Examples with soctypes are:
+					    - "renesas,rsrc-card,lager"
+					    - "renesas,rsrc-card,koelsch"
+Optional properties:
+
+- card_name				: User specified audio sound card name, one string
+					  property.
+- cpu					: CPU   sub-node
+- codec					: CODEC sub-node
+
+Optional subnode properties:
+
+- format				: CPU/CODEC common audio format.
+					  "i2s", "right_j", "left_j" , "dsp_a"
+					  "dsp_b", "ac97", "pdm", "msb", "lsb"
+- frame-master				: Indicates dai-link frame master.
+					  phandle to a cpu or codec subnode.
+- bitclock-master			: Indicates dai-link bit clock master.
+					  phandle to a cpu or codec subnode.
+- bitclock-inversion			: bool property. Add this if the
+					  dai-link uses bit clock inversion.
+- frame-inversion			: bool property. Add this if the
+					  dai-link uses frame clock inversion.
+- convert-rate				: platform specified sampling rate convert
+
+Required CPU/CODEC subnodes properties:
+
+- sound-dai				: phandle and port of CPU/CODEC
+
+Optional CPU/CODEC subnodes properties:
+
+- clocks / system-clock-frequency	: specify subnode's clock if needed.
+					  it can be specified via "clocks" if system has
+					  clock node (= common clock), or "system-clock-frequency"
+					  (if system doens't support common clock)
+					  If a clock is specified, it is
+					  enabled with clk_prepare_enable()
+					  in dai startup() and disabled with
+					  clk_disable_unprepare() in dai
+					  shutdown().
+
+Example
+
+sound {
+	compatible = "renesas,rsrc-card,lager";
+
+	card-name = "rsnd-ak4643";
+	format = "left_j";
+	bitclock-master = <&sndcodec>;
+	frame-master = <&sndcodec>;
+
+	sndcpu: cpu {
+		sound-dai = <&rcar_sound>;
+	};
+
+	sndcodec: codec {
+		sound-dai = <&ak4643>;
+		system-clock-frequency = <11289600>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
new file mode 100644
index 000000000..9b82c20b3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rockchip-i2s.txt
@@ -0,0 +1,37 @@
+* Rockchip I2S controller
+
+The I2S bus (Inter-IC sound bus) is a serial link for digital
+audio data transfer between devices in the system.
+
+Required properties:
+
+- compatible: should be one of the followings
+   - "rockchip,rk3066-i2s": for rk3066
+   - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188
+   - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: should contain the I2S interrupt.
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: should include "tx" and "rx".
+- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names.
+- clock-names: should contain followings:
+   - "i2s_hclk": clock for I2S BUS
+   - "i2s_clk" : clock for I2S controller
+
+Example for rk3288 I2S controller:
+
+i2s@ff890000 {
+	compatible = "rockchip,rk3288-i2s", "rockchip,rk3066-i2s";
+	reg = <0xff890000 0x10000>;
+	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	dmas = <&pdma1 0>, <&pdma1 1>;
+	dma-names = "tx", "rx";
+	clock-names = "i2s_hclk", "i2s_clk";
+	clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rt5631.txt b/kernel/Documentation/devicetree/bindings/sound/rt5631.txt
new file mode 100644
index 000000000..92b986ca3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rt5631.txt
@@ -0,0 +1,48 @@
+ALC5631/RT5631 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "realtek,alc5631" or "realtek,rt5631"
+
+  - reg : the I2C address of the device.
+
+Pins on the device (for linking into audio routes):
+
+  * SPK_OUT_R_P
+  * SPK_OUT_R_N
+  * SPK_OUT_L_P
+  * SPK_OUT_L_N
+  * HP_OUT_L
+  * HP_OUT_R
+  * AUX_OUT2_LP
+  * AUX_OUT2_RN
+  * AUX_OUT1_LP
+  * AUX_OUT1_RN
+  * AUX_IN_L_JD
+  * AUX_IN_R_JD
+  * MONO_IN_P
+  * MONO_IN_N
+  * MIC1_P
+  * MIC1_N
+  * MIC2_P
+  * MIC2_N
+  * MONO_OUT_P
+  * MONO_OUT_N
+  * MICBIAS1
+  * MICBIAS2
+
+Example:
+
+alc5631: alc5631@1a {
+	compatible = "realtek,alc5631";
+	reg = <0x1a>;
+};
+
+or
+
+rt5631: rt5631@1a {
+	compatible = "realtek,rt5631";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rt5640.txt b/kernel/Documentation/devicetree/bindings/sound/rt5640.txt
new file mode 100644
index 000000000..bac4d9ac1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rt5640.txt
@@ -0,0 +1,53 @@
+RT5640/RT5639 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : One of "realtek,rt5640" or "realtek,rt5639".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+- realtek,in1-differential
+- realtek,in2-differential
+  Boolean. Indicate MIC1/2 input are differential, rather than single-ended.
+
+- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
+
+Pins on the device (for linking into audio routes) for RT5639/RT5640:
+
+  * DMIC1
+  * DMIC2
+  * MICBIAS1
+  * IN1P
+  * IN1R
+  * IN2P
+  * IN2R
+  * HPOL
+  * HPOR
+  * LOUTL
+  * LOUTR
+  * SPOLP
+  * SPOLN
+  * SPORP
+  * SPORN
+
+Additional pins on the device for RT5640:
+
+  * MONOP
+  * MONON
+
+Example:
+
+rt5640 {
+	compatible = "realtek,rt5640";
+	reg = <0x1c>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>;
+	realtek,ldo1-en-gpios =
+		<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/rt5677.txt b/kernel/Documentation/devicetree/bindings/sound/rt5677.txt
new file mode 100644
index 000000000..740ff771a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/rt5677.txt
@@ -0,0 +1,76 @@
+RT5677 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "realtek,rt5677".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+- gpio-controller : Indicates this device is a GPIO controller.
+
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+
+Optional properties:
+
+- realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin.
+
+- realtek,in1-differential
+- realtek,in2-differential
+- realtek,lout1-differential
+- realtek,lout2-differential
+- realtek,lout3-differential
+  Boolean. Indicate MIC1/2 input and LOUT1/2/3 outputs are differential,
+  rather than single-ended.
+
+- realtek,gpio-config
+  Array of six 8bit elements that configures GPIO.
+    0 - floating (reset value)
+    1 - pull down
+    2 - pull up
+
+- realtek,jd1-gpio
+  Configures GPIO Mic Jack detection 1.
+  Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively.
+
+- realtek,jd2-gpio
+- realtek,jd3-gpio
+  Configures GPIO Mic Jack detection 2 and 3.
+  Select 0 ~ 3 as OFF, GPIO4, GPIO5 and GPIO6 respectively.
+
+Pins on the device (for linking into audio routes):
+
+  * IN1P
+  * IN1N
+  * IN2P
+  * IN2N
+  * MICBIAS1
+  * DMIC1
+  * DMIC2
+  * DMIC3
+  * DMIC4
+  * LOUT1
+  * LOUT2
+  * LOUT3
+
+Example:
+
+rt5677 {
+	compatible = "realtek,rt5677";
+	reg = <0x2c>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	realtek,pow-ldo2-gpio =
+		<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+	realtek,in1-differential = "true";
+	realtek,gpio-config = /bits/ 8  <0 0 0 0 0 2>;   /* pull up GPIO6 */
+	realtek,jd2-gpio = <3>;  /* Enables Jack detection for GPIO6 */
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt b/kernel/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt
new file mode 100644
index 000000000..9148f7231
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/samsung,odroidx2-max98090.txt
@@ -0,0 +1,35 @@
+Samsung Exynos Odroid X2/U3 audio complex with MAX98090 codec
+
+Required properties:
+ - compatible : "samsung,odroidx2-audio" - for Odroid X2 board,
+		"samsung,odroidu3-audio" - for Odroid U3 board
+ - samsung,model : the user-visible name of this sound complex
+ - samsung,i2s-controller : the phandle of the I2S controller
+ - samsung,audio-codec : the phandle of the MAX98090 audio codec
+ - samsung,audio-routing : a list of the connections between audio
+   components;  each entry is a pair of strings, the first being the
+   connection's sink, the second being the connection's source;
+   valid names for sources and sinks are the MAX98090's pins (as
+   documented in its binding), and the jacks on the board
+   For Odroid X2:
+     * Headphone Jack
+     * Mic Jack
+     * DMIC
+
+   For Odroid U3:
+     * Headphone Jack
+     * Speakers
+
+Example:
+
+sound {
+	compatible = "samsung,odroidu3-audio";
+	samsung,i2s-controller = <&i2s0>;
+	samsung,audio-codec = <&max98090>;
+	samsung,model = "Odroid-X2";
+	samsung,audio-routing =
+		"Headphone Jack", "HPL",
+		"Headphone Jack", "HPR",
+		"IN1", "Mic Jack",
+		"Mic Jack", "MICBIAS";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt b/kernel/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt
new file mode 100644
index 000000000..4686646fb
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/samsung,smdk-wm8994.txt
@@ -0,0 +1,14 @@
+Samsung SMDK audio complex
+
+Required properties:
+- compatible : "samsung,smdk-wm8994"
+- samsung,i2s-controller: The phandle of the Samsung I2S0 controller
+- samsung,audio-codec: The phandle of the WM8994 audio codec
+Example:
+
+sound {
+		compatible = "samsung,smdk-wm8994";
+
+		samsung,i2s-controller = <&i2s0>;
+		samsung,audio-codec = <&wm8994>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/kernel/Documentation/devicetree/bindings/sound/samsung-i2s.txt
new file mode 100644
index 000000000..09e0e1859
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/samsung-i2s.txt
@@ -0,0 +1,82 @@
+* Samsung I2S controller
+
+Required SoC Specific Properties:
+
+- compatible : should be one of the following.
+   - samsung,s3c6410-i2s: for 8/16/24bit stereo I2S.
+   - samsung,s5pv210-i2s: for 8/16/24bit multichannel(5.1) I2S with
+     secondary fifo, s/w reset control and internal mux for root clk src.
+   - samsung,exynos5420-i2s: for 8/16/24bit multichannel(5.1) I2S for
+     playback, sterio channel capture, secondary fifo using internal
+     or external dma, s/w reset control, internal mux for root clk src
+     and 7.1 channel TDM support for playback. TDM (Time division multiplexing)
+     is to allow transfer of multiple channel audio data on single data line.
+   - samsung,exynos7-i2s: with all the available features of exynos5 i2s,
+     exynos7 I2S has 7.1 channel TDM support for capture, secondary fifo
+     with only external dma and more no.of root clk sampling frequencies.
+   - samsung,exynos7-i2s1: I2S1 on previous samsung platforms supports
+     stereo channels. exynos7 i2s1 upgraded to 5.1 multichannel with
+     slightly modified bit offsets.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- dmas: list of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+- clocks: Handle to iis clock and RCLK source clk.
+- clock-names:
+  i2s0 uses some base clks from CMU and some are from audio subsystem internal
+  clock controller. The clock names for i2s0 should be "iis", "i2s_opclk0" and
+  "i2s_opclk1" as shown in the example below.
+  i2s1 and i2s2 uses clocks from CMU. The clock names for i2s1 and i2s2 should
+  be "iis" and "i2s_opclk0".
+  "iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root
+  clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2
+  doesn't have any such mux.
+- #clock-cells: should be 1, this property must be present if the I2S device
+  is a clock provider in terms of the common clock bindings, described in
+  ../clock/clock-bindings.txt.
+- clock-output-names: from the common clock bindings, names of the CDCLK
+  I2S output clocks, suggested values are "i2s_cdclk0", "i2s_cdclk1",
+  "i2s_cdclk3" for the I2S0, I2S1, I2S2 devices recpectively.
+
+There are following clocks available at the I2S device nodes:
+ CLK_I2S_CDCLK    - the CDCLK (CODECLKO) gate clock,
+ CLK_I2S_RCLK_PSR - the RCLK prescaler divider clock (corresponding to the
+		    IISPSR register),
+ CLK_I2S_RCLK_SRC - the RCLKSRC mux clock (corresponding to RCLKSRC bit in
+		    IISMOD register).
+
+Refer to the SoC datasheet for availability of the above clocks.
+The CLK_I2S_RCLK_PSR and CLK_I2S_RCLK_SRC clocks are usually only available
+in the IIS Multi Audio Interface (I2S0).
+Note: Old DTs may not have the #clock-cells, clock-output-names properties
+and then not use the I2S node as a clock supplier.
+
+Optional SoC Specific Properties:
+
+- samsung,idma-addr: Internal DMA register base address of the audio
+  sub system(used in secondary sound source).
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
+
+
+Example:
+
+i2s0: i2s@03830000 {
+	compatible = "samsung,s5pv210-i2s";
+	reg = <0x03830000 0x100>;
+	dmas = <&pdma0 10
+		&pdma0 9
+		&pdma0 8>;
+	dma-names = "tx", "rx", "tx-sec";
+	clocks = <&clock_audss EXYNOS_I2S_BUS>,
+		<&clock_audss EXYNOS_I2S_BUS>,
+		<&clock_audss EXYNOS_SCLK_I2S>;
+	clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+	#clock-cells;
+	clock-output-names = "i2s_cdclk0";
+	samsung,idma-addr = <0x03000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_bus>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/sgtl5000.txt b/kernel/Documentation/devicetree/bindings/sound/sgtl5000.txt
new file mode 100644
index 000000000..0e5e4eb3e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/sgtl5000.txt
@@ -0,0 +1,39 @@
+* Freescale SGTL5000 Stereo Codec
+
+Required properties:
+- compatible : "fsl,sgtl5000".
+
+- reg : the I2C address of the device
+
+- clocks : the clock provider of SYS_MCLK
+
+- micbias-resistor-k-ohms : the bias resistor to be used in kOmhs
+	The resistor can take values of 2k, 4k or 8k.
+	If set to 0 it will be off.
+	If this node is not mentioned or if the value is unknown, then
+	micbias	resistor is set to 4K.
+
+- micbias-voltage-m-volts : the bias voltage to be used in mVolts
+	The voltage can take values from 1.25V to 3V by 250mV steps
+	If this node is not mentionned or the value is unknown, then
+	the value is set to 1.25V.
+
+- VDDA-supply : the regulator provider of VDDA
+
+- VDDIO-supply: the regulator provider of VDDIO
+
+Optional properties:
+
+- VDDD-supply : the regulator provider of VDDD
+
+Example:
+
+codec: sgtl5000@0a {
+	compatible = "fsl,sgtl5000";
+	reg = <0x0a>;
+	clocks = <&clks 150>;
+	micbias-resistor-k-ohms = <2>;
+	micbias-voltage-m-volts = <2250>;
+	VDDA-supply = <&reg_3p3v>;
+	VDDIO-supply = <&reg_3p3v>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/simple-card.txt b/kernel/Documentation/devicetree/bindings/sound/simple-card.txt
new file mode 100644
index 000000000..73bf314f7
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/simple-card.txt
@@ -0,0 +1,160 @@
+Simple-Card:
+
+Simple-Card specifies audio DAI connections of SoC <-> codec.
+
+Required properties:
+
+- compatible				: "simple-audio-card"
+
+Optional properties:
+
+- simple-audio-card,name		: User specified audio sound card name, one string
+					  property.
+- simple-audio-card,widgets		: Please refer to widgets.txt.
+- simple-audio-card,routing		: A list of the connections between audio components.
+					  Each entry is a pair of strings, the first being the
+					  connection's sink, the second being the connection's
+					  source.
+- simple-audio-card,mclk-fs             : Multiplication factor between stream rate and codec
+  					  mclk.
+- simple-audio-card,hp-det-gpio		: Reference to GPIO that signals when
+					  headphones are attached.
+- simple-audio-card,mic-det-gpio	: Reference to GPIO that signals when
+					  a microphone is attached.
+
+Optional subnodes:
+
+- simple-audio-card,dai-link		: Container for dai-link level
+					  properties and the CPU and CODEC
+					  sub-nodes. This container may be
+					  omitted when the card has only one
+					  DAI link. See the examples and the
+					  section bellow.
+
+Dai-link subnode properties and subnodes:
+
+If dai-link subnode is omitted and the subnode properties are directly
+under "sound"-node the subnode property and subnode names have to be
+prefixed with "simple-audio-card,"-prefix.
+
+Required dai-link subnodes:
+
+- cpu					: CPU   sub-node
+- codec					: CODEC sub-node
+
+Optional dai-link subnode properties:
+
+- format				: CPU/CODEC common audio format.
+					  "i2s", "right_j", "left_j" , "dsp_a"
+					  "dsp_b", "ac97", "pdm", "msb", "lsb"
+- frame-master				: Indicates dai-link frame master.
+					  phandle to a cpu or codec subnode.
+- bitclock-master			: Indicates dai-link bit clock master.
+					  phandle to a cpu or codec subnode.
+- bitclock-inversion			: bool property. Add this if the
+					  dai-link uses bit clock inversion.
+- frame-inversion			: bool property. Add this if the
+					  dai-link uses frame clock inversion.
+
+For backward compatibility the frame-master and bitclock-master
+properties can be used as booleans in codec subnode to indicate if the
+codec is the dai-link frame or bit clock master. In this case there
+should be no dai-link node, the same properties should not be present
+at sound-node level, and the bitclock-inversion and frame-inversion
+properties should also be placed in the codec node if needed.
+
+Required CPU/CODEC subnodes properties:
+
+- sound-dai				: phandle and port of CPU/CODEC
+
+Optional CPU/CODEC subnodes properties:
+
+- dai-tdm-slot-num			: Please refer to tdm-slot.txt.
+- dai-tdm-slot-width			: Please refer to tdm-slot.txt.
+- clocks / system-clock-frequency	: specify subnode's clock if needed.
+					  it can be specified via "clocks" if system has
+					  clock node (= common clock), or "system-clock-frequency"
+					  (if system doens't support common clock)
+					  If a clock is specified, it is
+					  enabled with clk_prepare_enable()
+					  in dai startup() and disabled with
+					  clk_disable_unprepare() in dai
+					  shutdown().
+
+Example 1 - single DAI link:
+
+sound {
+	compatible = "simple-audio-card";
+	simple-audio-card,name = "VF610-Tower-Sound-Card";
+	simple-audio-card,format = "left_j";
+	simple-audio-card,bitclock-master = <&dailink0_master>;
+	simple-audio-card,frame-master = <&dailink0_master>;
+	simple-audio-card,widgets =
+		"Microphone", "Microphone Jack",
+		"Headphone", "Headphone Jack",
+		"Speaker", "External Speaker";
+	simple-audio-card,routing =
+		"MIC_IN", "Microphone Jack",
+		"Headphone Jack", "HP_OUT",
+		"External Speaker", "LINE_OUT";
+
+	simple-audio-card,cpu {
+		sound-dai = <&sh_fsi2 0>;
+	};
+
+	dailink0_master: simple-audio-card,codec {
+		sound-dai = <&ak4648>;
+		clocks = <&osc>;
+	};
+};
+
+&i2c0 {
+	ak4648: ak4648@12 {
+		#sound-dai-cells = <0>;
+		compatible = "asahi-kasei,ak4648";
+		reg = <0x12>;
+	};
+};
+
+sh_fsi2: sh_fsi2@ec230000 {
+	#sound-dai-cells = <1>;
+	compatible = "renesas,sh_fsi2";
+	reg = <0xec230000 0x400>;
+	interrupt-parent = <&gic>;
+	interrupts = <0 146 0x4>;
+};
+
+Example 2 - many DAI links:
+
+sound {
+	compatible = "simple-audio-card";
+	simple-audio-card,name = "Cubox Audio";
+
+	simple-audio-card,dai-link@0 {		/* I2S - HDMI */
+		format = "i2s";
+		cpu {
+			sound-dai = <&audio1 0>;
+		};
+		codec {
+			sound-dai = <&tda998x 0>;
+		};
+	};
+
+	simple-audio-card,dai-link@1 {		/* S/PDIF - HDMI */
+		cpu {
+			sound-dai = <&audio1 1>;
+		};
+		codec {
+			sound-dai = <&tda998x 1>;
+		};
+	};
+
+	simple-audio-card,dai-link@2 {		/* S/PDIF - S/PDIF */
+		cpu {
+			sound-dai = <&audio1 1>;
+		};
+		codec {
+			sound-dai = <&spdif_codec>;
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt b/kernel/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
new file mode 100644
index 000000000..062f5ec36
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
@@ -0,0 +1,17 @@
+SiRF internal audio CODEC
+
+Required properties:
+
+  - compatible : "sirf,atlas6-audio-codec" or "sirf,prima2-audio-codec"
+
+  - reg : the register address of the device.
+
+  - clocks: the clock of SiRF internal audio codec
+
+Example:
+
+audiocodec: audiocodec@b0040000 {
+	compatible = "sirf,atlas6-audio-codec";
+	reg = <0xb0040000 0x10000>;
+	clocks = <&clks 27>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/sirf-audio-port.txt b/kernel/Documentation/devicetree/bindings/sound/sirf-audio-port.txt
new file mode 100644
index 000000000..1f66de3c8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/sirf-audio-port.txt
@@ -0,0 +1,20 @@
+* SiRF SoC audio port
+
+Required properties:
+- compatible: "sirf,audio-port"
+- reg: Base address and size entries:
+- dmas: List of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: Identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+  One of the DMA channels will be responsible for transmission (should be
+  named "tx") and one for reception (should be named "rx").
+
+Example:
+
+audioport: audioport@b0040000 {
+	compatible = "sirf,audio-port";
+	reg = <0xb0040000 0x10000>;
+	dmas = <&dmac1 3>, <&dmac1 8>;
+	dma-names = "rx", "tx";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/sirf-audio.txt b/kernel/Documentation/devicetree/bindings/sound/sirf-audio.txt
new file mode 100644
index 000000000..c88882ca3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/sirf-audio.txt
@@ -0,0 +1,41 @@
+* SiRF atlas6 and prima2 internal audio codec and port based audio setups
+
+Required properties:
+- compatible: "sirf,sirf-audio-card"
+- sirf,audio-platform: phandle for the platform node
+- sirf,audio-codec: phandle for the SiRF internal codec node
+
+Optional properties:
+- hp-pa-gpios: Need to be present if the board need control external
+  headphone amplifier.
+- spk-pa-gpios: Need to be present if the board need control external
+  speaker amplifier.
+- hp-switch-gpios: Need to be present if the board capable to detect jack
+  insertion, removal.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Ext Spk
+ * Line In
+ * Mic
+
+SiRF internal audio codec pins:
+ * HPOUTL
+ * HPOUTR
+ * SPKOUT
+ * Ext Mic
+ * Mic Bias
+
+Example:
+
+sound {
+		compatible = "sirf,sirf-audio-card";
+		sirf,audio-codec = <&audiocodec>;
+		sirf,audio-platform = <&audioport>;
+		hp-pa-gpios = <&gpio 44 0>;
+		spk-pa-gpios = <&gpio 46 0>;
+		hp-switch-gpios = <&gpio 45 0>;
+};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/sirf-usp.txt b/kernel/Documentation/devicetree/bindings/sound/sirf-usp.txt
new file mode 100644
index 000000000..02f85b32d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/sirf-usp.txt
@@ -0,0 +1,27 @@
+* SiRF SoC USP module
+
+Required properties:
+- compatible: "sirf,prima2-usp-pcm"
+- reg: Base address and size entries:
+- dmas: List of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: Identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+
+  One of the DMA channels will be responsible for transmission (should be
+  named "tx") and one for reception (should be named "rx").
+
+- clocks: USP controller clock source
+- pinctrl-names: Must contain a "default" entry.
+- pinctrl-NNN: One property must exist for each entry in pinctrl-names.
+
+Example:
+usp0: usp@b0080000 {
+	compatible = "sirf,prima2-usp-pcm";
+	reg = <0xb0080000 0x10000>;
+	clocks = <&clks 28>;
+	dmas = <&dmac1 1>, <&dmac1 2>;
+	dma-names = "rx", "tx";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usp0_only_utfs_pins_a>;
+};
+
diff --git a/kernel/Documentation/devicetree/bindings/sound/snow.txt b/kernel/Documentation/devicetree/bindings/sound/snow.txt
new file mode 100644
index 000000000..6df74f156
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/snow.txt
@@ -0,0 +1,22 @@
+Audio Binding for Snow boards
+
+Required properties:
+- compatible : Can be one of the following,
+			"google,snow-audio-max98090" or
+			"google,snow-audio-max98091" or
+			"google,snow-audio-max98095"
+- samsung,i2s-controller: The phandle of the Samsung I2S controller
+- samsung,audio-codec: The phandle of the audio codec
+
+Optional:
+- samsung,model: The name of the sound-card
+
+Example:
+
+sound {
+		compatible = "google,snow-audio-max98095";
+
+		samsung,model = "Snow-I2S-MAX98095";
+		samsung,i2s-controller = <&i2s0>;
+		samsung,audio-codec = <&max98095>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/soc-ac97link.txt b/kernel/Documentation/devicetree/bindings/sound/soc-ac97link.txt
new file mode 100644
index 000000000..80152a87f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/soc-ac97link.txt
@@ -0,0 +1,28 @@
+AC97 link bindings
+
+These bindings can be included within any other device node.
+
+Required properties:
+ - pinctrl-names: Has to contain following states to setup the correct
+   pinmuxing for the used gpios:
+	"ac97-running": AC97-link is active
+	"ac97-reset": AC97-link reset state
+	"ac97-warm-reset": AC97-link warm reset state
+ - ac97-gpios: List of gpio phandles with args in the order ac97-sync,
+   ac97-sdata, ac97-reset
+
+
+Example:
+
+ssi {
+	...
+
+	pinctrl-names = "default", "ac97-running", "ac97-reset", "ac97-warm-reset";
+	pinctrl-0 = <&ac97link_running>;
+	pinctrl-1 = <&ac97link_running>;
+	pinctrl-2 = <&ac97link_reset>;
+	pinctrl-3 = <&ac97link_warm_reset>;
+	ac97-gpios = <&gpio3 20 0 &gpio3 22 0 &gpio3 28 0>;
+
+	...
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/spdif-receiver.txt b/kernel/Documentation/devicetree/bindings/sound/spdif-receiver.txt
new file mode 100644
index 000000000..80f807bf8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/spdif-receiver.txt
@@ -0,0 +1,10 @@
+Device-Tree bindings for dummy spdif receiver
+
+Required properties:
+	- compatible: should be "linux,spdif-dir".
+
+Example node:
+
+	codec: spdif-receiver {
+		compatible = "linux,spdif-dir";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/spdif-transmitter.txt b/kernel/Documentation/devicetree/bindings/sound/spdif-transmitter.txt
new file mode 100644
index 000000000..55a85841d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/spdif-transmitter.txt
@@ -0,0 +1,10 @@
+Device-Tree bindings for dummy spdif transmitter
+
+Required properties:
+	- compatible: should be "linux,spdif-dit".
+
+Example node:
+
+	codec: spdif-transmitter {
+		compatible = "linux,spdif-dit";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ssm2518.txt b/kernel/Documentation/devicetree/bindings/sound/ssm2518.txt
new file mode 100644
index 000000000..59381a778
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ssm2518.txt
@@ -0,0 +1,20 @@
+SSM2518 audio amplifier
+
+This device supports I2C only.
+
+Required properties:
+  - compatible : Must be "adi,ssm2518"
+  - reg : the I2C address of the device. This will either be 0x34 (ADDR pin low)
+	or 0x35 (ADDR pin high)
+
+Optional properties:
+  - gpios : GPIO connected to the nSD pin. If the property is not present it is
+	        assumed that the nSD pin is hardwired to always on.
+
+Example:
+
+	ssm2518: ssm2518@34 {
+		compatible = "adi,ssm2518";
+		reg = <0x34>;
+		gpios = <&gpio 5 0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ssm4567.txt b/kernel/Documentation/devicetree/bindings/sound/ssm4567.txt
new file mode 100644
index 000000000..ec3d9e700
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ssm4567.txt
@@ -0,0 +1,15 @@
+Analog Devices SSM4567 audio amplifier
+
+This device supports I2C only.
+
+Required properties:
+  - compatible : Must be "adi,ssm4567"
+  - reg : the I2C address of the device. This will either be 0x34 (LR_SEL/ADDR connected to AGND),
+	0x35 (LR_SEL/ADDR connected to IOVDD) or 0x36 (LR_SEL/ADDR open).
+
+Example:
+
+	ssm4567: ssm4567@34 {
+		compatible = "adi,ssm4567";
+		reg = <0x34>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/st,sta32x.txt b/kernel/Documentation/devicetree/bindings/sound/st,sta32x.txt
new file mode 100644
index 000000000..255de3ae5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/st,sta32x.txt
@@ -0,0 +1,92 @@
+STA32X audio CODEC
+
+The driver for this device only supports I2C.
+
+Required properties:
+
+  - compatible: "st,sta32x"
+  - reg: the I2C address of the device for I2C
+  - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+  - power-down-gpios: a GPIO spec for the power down pin. If specified,
+		      it will be deasserted before communication to the codec
+		      starts.
+
+  - Vdda-supply: regulator spec, providing 3.3V
+  - Vdd3-supply: regulator spec, providing 3.3V
+  - Vcc-supply: regulator spec, providing 5V - 26V
+
+Optional properties:
+
+  -  st,output-conf: number, Selects the output configuration:
+	0: 2-channel (full-bridge) power, 2-channel data-out
+	1: 2 (half-bridge). 1 (full-bridge) on-board power
+	2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
+	3: 1 Channel Mono-Parallel
+	If parameter is missing, mode 0 will be enabled.
+	This property has to be specified as '/bits/ 8' value.
+
+  -  st,ch1-output-mapping: Channel 1 output mapping
+  -  st,ch2-output-mapping: Channel 2 output mapping
+  -  st,ch3-output-mapping: Channel 3 output mapping
+	0: Channel 1
+	1: Channel 2
+	2: Channel 3
+	If parameter is missing, channel 1 is chosen.
+	This properties have to be specified as '/bits/ 8' values.
+
+  -  st,thermal-warning-recover:
+	If present, thermal warning recovery is enabled.
+
+  -  st,thermal-warning-adjustment:
+	If present, thermal warning adjustment is enabled.
+
+  -  st,fault-detect-recovery:
+	If present, then fault recovery will be enabled.
+
+  -  st,drop-compensation-ns: number
+	Only required for "st,ffx-power-output-mode" ==
+	"variable-drop-compensation".
+	Specifies the drop compensation in nanoseconds.
+	The value must be in the range of 0..300, and only
+	multiples of 20 are allowed. Default is 140ns.
+
+  -  st,max-power-use-mpcc:
+	If present, then MPCC bits are used for MPC coefficients,
+	otherwise standard MPC coefficients are used.
+
+  -  st,max-power-corr:
+	If present, power bridge correction for THD reduction near maximum
+	power output is enabled.
+
+  -  st,am-reduction-mode:
+	If present, FFX mode runs in AM reduction mode, otherwise normal
+	FFX mode is used.
+
+  -  st,odd-pwm-speed-mode:
+	If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
+	channels. If not present, normal PWM spped mode (384 kHz) will be used.
+
+  -  st,invalid-input-detect-mute:
+	If present, automatic invalid input detect mute is enabled.
+
+Example:
+
+codec: sta32x@38 {
+	compatible = "st,sta32x";
+	reg = <0x1c>;
+	reset-gpios = <&gpio1 19 0>;
+	power-down-gpios = <&gpio1 16 0>;
+	st,output-conf = /bits/ 8  <0x3>;	// set output to 2-channel
+						// (full-bridge) power,
+						// 2-channel data-out
+	st,ch1-output-mapping = /bits/ 8 <0>;	// set channel 1 output ch 1
+	st,ch2-output-mapping = /bits/ 8 <0>;	// set channel 2 output ch 1
+	st,ch3-output-mapping = /bits/ 8 <0>;	// set channel 3 output ch 1
+	st,max-power-correction;		// enables power bridge
+						// correction for THD reduction
+						// near maximum power output
+	st,invalid-input-detect-mute;		// mute if no valid digital
+						// audio signal is provided.
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/st,sta350.txt b/kernel/Documentation/devicetree/bindings/sound/st,sta350.txt
new file mode 100644
index 000000000..307398ef2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/st,sta350.txt
@@ -0,0 +1,131 @@
+STA350 audio CODEC
+
+The driver for this device only supports I2C.
+
+Required properties:
+
+  - compatible: "st,sta350"
+  - reg: the I2C address of the device for I2C
+  - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+  - power-down-gpios: a GPIO spec for the power down pin. If specified,
+		      it will be deasserted before communication to the codec
+		      starts.
+
+  - vdd-dig-supply: regulator spec, providing 3.3V
+  - vdd-pll-supply: regulator spec, providing 3.3V
+  - vcc-supply: regulator spec, providing 5V - 26V
+
+Optional properties:
+
+  -  st,output-conf: number, Selects the output configuration:
+	0: 2-channel (full-bridge) power, 2-channel data-out
+	1: 2 (half-bridge). 1 (full-bridge) on-board power
+	2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
+	3: 1 Channel Mono-Parallel
+	If parameter is missing, mode 0 will be enabled.
+	This property has to be specified as '/bits/ 8' value.
+
+  -  st,ch1-output-mapping: Channel 1 output mapping
+  -  st,ch2-output-mapping: Channel 2 output mapping
+  -  st,ch3-output-mapping: Channel 3 output mapping
+	0: Channel 1
+	1: Channel 2
+	2: Channel 3
+	If parameter is missing, channel 1 is chosen.
+	This properties have to be specified as '/bits/ 8' values.
+
+  -  st,thermal-warning-recover:
+	If present, thermal warning recovery is enabled.
+
+  -  st,thermal-warning-adjustment:
+	If present, thermal warning adjustment is enabled.
+
+  -  st,fault-detect-recovery:
+	If present, then fault recovery will be enabled.
+
+  -  st,ffx-power-output-mode: string
+	The FFX power output mode selects how the FFX output timing is
+	configured. Must be one of these values:
+	  -  "drop-compensation"
+	  -  "tapered-compensation"
+	  -  "full-power-mode"
+	  -  "variable-drop-compensation" (default)
+
+  -  st,drop-compensation-ns: number
+	Only required for "st,ffx-power-output-mode" ==
+	"variable-drop-compensation".
+	Specifies the drop compensation in nanoseconds.
+	The value must be in the range of 0..300, and only
+	multiples of 20 are allowed. Default is 140ns.
+
+  -  st,overcurrent-warning-adjustment:
+	If present, overcurrent warning adjustment is enabled.
+
+  -  st,max-power-use-mpcc:
+	If present, then MPCC bits are used for MPC coefficients,
+	otherwise standard MPC coefficients are used.
+
+  -  st,max-power-corr:
+	If present, power bridge correction for THD reduction near maximum
+	power output is enabled.
+
+  -  st,am-reduction-mode:
+	If present, FFX mode runs in AM reduction mode, otherwise normal
+	FFX mode is used.
+
+  -  st,odd-pwm-speed-mode:
+	If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
+	channels. If not present, normal PWM spped mode (384 kHz) will be used.
+
+  -  st,distortion-compensation:
+	If present, distortion compensation variable uses DCC coefficient.
+	If not present, preset DC coefficient is used.
+
+  -  st,invalid-input-detect-mute:
+	If present, automatic invalid input detect mute is enabled.
+
+  -  st,activate-mute-output:
+	If present, a mute output will be activated in ase the volume will
+	reach a value lower than -76 dBFS.
+
+  -  st,bridge-immediate-off:
+	If present, the bridge will be switched off immediately after the
+	power-down-gpio goes low. Otherwise, the bridge will wait for 13
+	million clock cycles to pass before shutting down.
+
+  -  st,noise-shape-dc-cut:
+	If present, the noise-shaping technique on the DC cutoff filter are
+	enabled.
+
+  -  st,powerdown-master-volume:
+	If present, the power-down pin and I2C power-down functions will
+	act on the master volume. Otherwise, the functions will act on the
+	mute commands.
+
+  -  st,powerdown-delay-divider:
+	If present, the bridge power-down time will be divided by the provided
+	value. If not specified, a divider of 1 will be used. Allowed values
+	are 1, 2, 4, 8, 16, 32, 64 and 128.
+	This property has to be specified as '/bits/ 8' value.
+
+Example:
+
+codec: sta350@38 {
+	compatible = "st,sta350";
+	reg = <0x1c>;
+	reset-gpios = <&gpio1 19 0>;
+	power-down-gpios = <&gpio1 16 0>;
+	st,output-conf = /bits/ 8  <0x3>;	// set output to 2-channel
+						// (full-bridge) power,
+						// 2-channel data-out
+	st,ch1-output-mapping = /bits/ 8 <0>;	// set channel 1 output ch 1
+	st,ch2-output-mapping = /bits/ 8 <0>;	// set channel 2 output ch 1
+	st,ch3-output-mapping = /bits/ 8 <0>;	// set channel 3 output ch 1
+	st,max-power-correction;		// enables power bridge
+						// correction for THD reduction
+						// near maximum power output
+	st,invalid-input-detect-mute;		// mute if no valid digital
+						// audio signal is provided.
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/storm.txt b/kernel/Documentation/devicetree/bindings/sound/storm.txt
new file mode 100644
index 000000000..062a4c185
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/storm.txt
@@ -0,0 +1,23 @@
+* Sound complex for Storm boards
+
+Models a soundcard for Storm boards with the Qualcomm Technologies IPQ806x SOC
+connected to a MAX98357A DAC via I2S.
+
+Required properties:
+
+- compatible	: "google,storm-audio"
+- cpu		: Phandle of the CPU DAI
+- codec		: Phandle of the codec DAI
+
+Optional properties:
+
+- qcom,model	: The user-visible name of this sound card.
+
+Example:
+
+sound {
+	compatible = "google,storm-audio";
+	qcom,model = "ipq806x-storm";
+	cpu = <&lpass_cpu>;
+	codec = <&max98357a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tas2552.txt b/kernel/Documentation/devicetree/bindings/sound/tas2552.txt
new file mode 100644
index 000000000..55e2a0af5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tas2552.txt
@@ -0,0 +1,26 @@
+Texas Instruments - tas2552 Codec module
+
+The tas2552 serial control bus communicates through I2C protocols
+
+Required properties:
+	- compatible - One of:
+		"ti,tas2552" - TAS2552
+	- reg -  I2C slave address
+	- supply-*: Required supply regulators are:
+		"vbat"		battery voltage
+		"iovdd"		I/O Voltage
+		"avdd"		Analog DAC Voltage
+
+Optional properties:
+	- enable-gpio - gpio pin to enable/disable the device
+
+Example:
+
+tas2552: tas2552@41 {
+	compatible = "ti,tas2552";
+	reg = <0x41>;
+	enable-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+};
+
+For more product information please see the link below:
+http://www.ti.com/product/TAS2552
diff --git a/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt b/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt
new file mode 100644
index 000000000..6a2c84247
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tdm-slot.txt
@@ -0,0 +1,20 @@
+TDM slot:
+
+This specifies audio DAI's TDM slot.
+
+TDM slot properties:
+dai-tdm-slot-num : Number of slots in use.
+dai-tdm-slot-width :  Width in bits for each slot.
+
+For instance:
+	dai-tdm-slot-num = <2>;
+	dai-tdm-slot-width = <8>;
+
+And for each spcified driver, there could be one .of_xlate_tdm_slot_mask()
+to specify a explicit mapping of the channels and the slots. If it's absent
+the default snd_soc_of_xlate_tdm_slot_mask() will be used to generating the
+tx and rx masks.
+
+For snd_soc_of_xlate_tdm_slot_mask(), the tx and rx masks will use a 1 bit
+for an active slot as default, and the default active bits are at the LSB of
+the masks.
diff --git a/kernel/Documentation/devicetree/bindings/sound/ti,pcm1681.txt b/kernel/Documentation/devicetree/bindings/sound/ti,pcm1681.txt
new file mode 100644
index 000000000..4df17185a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ti,pcm1681.txt
@@ -0,0 +1,15 @@
+Texas Instruments PCM1681 8-channel PWM Processor
+
+Required properties:
+
+ - compatible:		Should contain "ti,pcm1681".
+ - reg:			The i2c address. Should contain <0x4c>.
+
+Examples:
+
+	i2c_bus {
+		pcm1681@4c {
+			compatible = "ti,pcm1681";
+			reg = <0x4c>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/kernel/Documentation/devicetree/bindings/sound/ti,tas5086.txt
new file mode 100644
index 000000000..234dad296
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ti,tas5086.txt
@@ -0,0 +1,48 @@
+Texas Instruments TAS5086 6-channel PWM Processor
+
+Required properties:
+
+ - compatible:		Should contain "ti,tas5086".
+ - reg:			The i2c address. Should contain <0x1b>.
+
+Optional properties:
+
+ - reset-gpio: 		A GPIO spec to define which pin is connected to the
+			chip's !RESET pin. If specified, the driver will
+			assert a hardware reset at probe time.
+
+ - ti,charge-period:	This property should contain the time in microseconds
+			that closely matches the external single-ended
+			split-capacitor charge period. The hardware chip
+			waits for this period of time before starting the
+			PWM signals. This helps reduce pops and clicks.
+
+			When not specified, the hardware default of 1300ms
+			is retained.
+
+ - ti,mid-z-channel-X:	Boolean properties, X being a number from 1 to 6.
+			If given, channel X will start with the Mid-Z start
+			sequence, otherwise the default Low-Z scheme is used.
+
+			The correct configuration depends on how the power
+			stages connected to the PWM output pins work. Not all
+			power stages are compatible to Mid-Z - please refer
+			to the datasheets for more details.
+
+			Most systems should not set any of these properties.
+
+ - avdd-supply:         Power supply for AVDD, providing 3.3V
+ - dvdd-supply:         Power supply for DVDD, providing 3.3V
+
+Examples:
+
+	i2c_bus {
+		tas5086@1b {
+			compatible = "ti,tas5086";
+			reg = <0x1b>;
+			reset-gpio = <&gpio 23 0>;
+			ti,charge-period = <156000>;
+			avdd-supply = <&vdd_3v3_reg>;
+			dvdd-supply = <&vdd_3v3_reg>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt b/kernel/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt
new file mode 100644
index 000000000..eff12be5e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tlv320aic31xx.txt
@@ -0,0 +1,61 @@
+Texas Instruments - tlv320aic31xx Codec module
+
+The tlv320aic31xx serial control bus communicates through I2C protocols
+
+Required properties:
+
+- compatible - "string" - One of:
+    "ti,tlv320aic310x" - Generic TLV320AIC31xx with mono speaker amp
+    "ti,tlv320aic311x" - Generic TLV320AIC31xx with stereo speaker amp
+    "ti,tlv320aic3100" - TLV320AIC3100 (mono speaker amp, no MiniDSP)
+    "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP)
+    "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP)
+    "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP)
+
+- reg - <int> -  I2C slave address
+- HPVDD-supply, SPRVDD-supply, SPLVDD-supply, AVDD-supply, IOVDD-supply,
+  DVDD-supply : power supplies for the device as covered in
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+Optional properties:
+
+- gpio-reset - gpio pin number used for codec reset
+- ai31xx-micbias-vg - MicBias Voltage setting
+        1 or MICBIAS_2_0V - MICBIAS output is powered to 2.0V
+        2 or MICBIAS_2_5V - MICBIAS output is powered to 2.5V
+        3 or MICBIAS_AVDD - MICBIAS output is connected to AVDD
+	If this node is not mentioned or if the value is unknown, then
+	micbias	is set to 2.0V.
+
+CODEC output pins:
+  * HPL
+  * HPR
+  * SPL, devices with stereo speaker amp
+  * SPR, devices with stereo speaker amp
+  * SPK, devices with mono speaker amp
+  * MICBIAS
+
+CODEC input pins:
+  * MIC1LP
+  * MIC1RP
+  * MIC1LM
+
+The pins can be used in referring sound node's audio-routing property.
+
+Example:
+#include <dt-bindings/sound/tlv320aic31xx-micbias.h>
+
+tlv320aic31xx: tlv320aic31xx@18 {
+	compatible = "ti,tlv320aic311x";
+	reg = <0x18>;
+
+	ai31xx-micbias-vg = <MICBIAS_OFF>;
+
+	HPVDD-supply = <&regulator>;
+	SPRVDD-supply = <&regulator>;
+	SPLVDD-supply = <&regulator>;
+	AVDD-supply = <&regulator>;
+	IOVDD-supply = <&regulator>;
+	DVDD-supply = <&regulator>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt b/kernel/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt
new file mode 100644
index 000000000..5e2741af2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tlv320aic32x4.txt
@@ -0,0 +1,30 @@
+Texas Instruments - tlv320aic32x4 Codec module
+
+The tlv320aic32x4 serial control bus communicates through I2C protocols
+
+Required properties:
+ - compatible: Should be "ti,tlv320aic32x4"
+ - reg: I2C slave address
+ - supply-*: Required supply regulators are:
+    "iov" - digital IO power supply
+    "ldoin" - LDO power supply
+    "dv" - Digital core power supply
+    "av" - Analog core power supply
+    If you supply ldoin, dv and av are optional. Otherwise they are required
+   See regulator/regulator.txt for more information about the detailed binding
+   format.
+
+Optional properties:
+ - reset-gpios: Reset-GPIO phandle with args as described in gpio/gpio.txt
+ - clocks/clock-names: Clock named 'mclk' for the master clock of the codec.
+   See clock/clock-bindings.txt for information about the detailed format.
+
+
+Example:
+
+codec: tlv320aic32x4@18 {
+	compatible = "ti,tlv320aic32x4";
+	reg = <0x18>;
+	clocks = <&clks 201>;
+	clock-names = "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tlv320aic3x.txt b/kernel/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
new file mode 100644
index 000000000..47a213c41
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tlv320aic3x.txt
@@ -0,0 +1,67 @@
+Texas Instruments - tlv320aic3x Codec module
+
+The tlv320aic3x serial control bus communicates through I2C protocols
+
+Required properties:
+
+- compatible - "string" - One of:
+    "ti,tlv320aic3x" - Generic TLV320AIC3x device
+    "ti,tlv320aic33" - TLV320AIC33
+    "ti,tlv320aic3007" - TLV320AIC3007
+    "ti,tlv320aic3106" - TLV320AIC3106
+    "ti,tlv320aic3104" - TLV320AIC3104
+
+
+- reg - <int> -  I2C slave address
+
+
+Optional properties:
+
+- gpio-reset - gpio pin number used for codec reset
+- ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
+				    - Not supported on tlv320aic3104
+- ai3x-micbias-vg - MicBias Voltage required.
+	1 - MICBIAS output is powered to 2.0V,
+	2 - MICBIAS output is powered to 2.5V,
+	3 - MICBIAS output is connected to AVDD,
+	If this node is not mentioned or if the value is incorrect, then MicBias
+	is powered down.
+- AVDD-supply, IOVDD-supply, DRVDD-supply, DVDD-supply : power supplies for the
+  device as covered in Documentation/devicetree/bindings/regulator/regulator.txt
+
+CODEC output pins:
+  * LLOUT
+  * RLOUT
+  * MONO_LOUT
+  * HPLOUT
+  * HPROUT
+  * HPLCOM
+  * HPRCOM
+
+CODEC input pins for TLV320AIC3104:
+  * MIC2L
+  * MIC2R
+  * LINE1L
+  * LINE1R
+
+CODEC input pins for other compatible codecs:
+  * MIC3L
+  * MIC3R
+  * LINE1L
+  * LINE2L
+  * LINE1R
+  * LINE2R
+
+The pins can be used in referring sound node's audio-routing property.
+
+Example:
+
+tlv320aic3x: tlv320aic3x@1b {
+	compatible = "ti,tlv320aic3x";
+	reg = <0x1b>;
+
+	AVDD-supply = <&regulator>;
+	IOVDD-supply = <&regulator>;
+	DRVDD-supply = <&regulator>;
+	DVDD-supply = <&regulator>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/tpa6130a2.txt b/kernel/Documentation/devicetree/bindings/sound/tpa6130a2.txt
new file mode 100644
index 000000000..6dfa740e4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/tpa6130a2.txt
@@ -0,0 +1,27 @@
+Texas Instruments - tpa6130a2 Codec module
+
+The tpa6130a2 serial control bus communicates through I2C protocols
+
+Required properties:
+
+- compatible - "string" - One of:
+    "ti,tpa6130a2" - TPA6130A2
+    "ti,tpa6140a2" - TPA6140A2
+
+
+- reg - <int> -  I2C slave address
+
+- Vdd-supply - <phandle> - power supply regulator
+
+Optional properties:
+
+- power-gpio - gpio pin to power the device
+
+Example:
+
+tpa6130a2: tpa6130a2@60 {
+	compatible = "ti,tpa6130a2";
+	reg = <0x60>;
+	Vdd-supply = <&vmmc2>;
+	power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ts3a227e.txt b/kernel/Documentation/devicetree/bindings/sound/ts3a227e.txt
new file mode 100644
index 000000000..a836881d9
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ts3a227e.txt
@@ -0,0 +1,31 @@
+Texas Instruments TS3A227E
+Autonomous Audio Accessory Detection and Configuration Switch
+
+The TS3A227E detect headsets of 3-ring and 4-ring standards and
+switches automatically to route the microphone correctly.  It also
+handles key press detection in accordance with the Android audio
+headset specification v1.0.
+
+Required properties:
+
+ - compatible:		Should contain "ti,ts3a227e".
+ - reg:			The i2c address. Should contain <0x3b>.
+ - interrupt-parent:	The parent interrupt controller
+ - interrupts:		Interrupt number for /INT pin from the 227e
+
+Optional properies:
+ - ti,micbias:   Intended MICBIAS voltage (datasheet section 9.6.7).
+      Select 0/1/2/3/4/5/6/7 to specify MACBIAS voltage
+      2.1V/2.2V/2.3V/2.4V/2.5V/2.6V/2.7V/2.8V
+      Default value is "1" (2.2V).
+
+Examples:
+
+	i2c {
+		ts3a227e@3b {
+			compatible = "ti,ts3a227e";
+			reg = <0x3b>;
+			interrupt-parent = <&gpio>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ux500-mop500.txt b/kernel/Documentation/devicetree/bindings/sound/ux500-mop500.txt
new file mode 100644
index 000000000..48e071c96
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ux500-mop500.txt
@@ -0,0 +1,39 @@
+* MOP500 Audio Machine Driver
+
+This node is responsible for linking together all ux500 Audio Driver components.
+
+Required properties:
+ - compatible              : "stericsson,snd-soc-mop500"
+
+Non-standard properties:
+ - stericsson,cpu-dai      : Phandle to the CPU-side DAI
+ - stericsson,audio-codec  : Phandle to the Audio CODEC
+ - stericsson,card-name    : Over-ride default card name
+
+Example:
+
+	sound {
+		compatible = "stericsson,snd-soc-mop500";
+
+		stericsson,cpu-dai = <&msp1 &msp3>;
+		stericsson,audio-codec = <&codec>;
+	};
+
+	msp1: msp@80124000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80124000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	msp3: msp@80125000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80125000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	codec: ab8500-codec {
+		compatible = "stericsson,ab8500-codec";
+		stericsson,earpeice-cmv = <950>; /* Units in mV. */
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/ux500-msp.txt b/kernel/Documentation/devicetree/bindings/sound/ux500-msp.txt
new file mode 100644
index 000000000..99acd9c77
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/ux500-msp.txt
@@ -0,0 +1,43 @@
+* ux500 MSP (CPU-side Digital Audio Interface)
+
+Required properties:
+ - compatible       :"stericsson,ux500-msp-i2s"
+ - reg              : Physical base address and length of the device's registers.
+
+Optional properties:
+ - interrupts       : The interrupt output from the device.
+ - interrupt-parent : The parent interrupt controller.
+ - <name>-supply    : Phandle to the regulator <name> supply
+
+Example:
+
+	sound {
+		compatible = "stericsson,snd-soc-mop500";
+
+		stericsson,platform-pcm-dma = <&pcm>;
+		stericsson,cpu-dai = <&msp1 &msp3>;
+		stericsson,audio-codec = <&codec>;
+	};
+
+	pcm: ux500-pcm {
+		compatible = "stericsson,ux500-pcm";
+	};
+
+	msp1: msp@80124000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80124000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	msp3: msp@80125000 {
+		compatible = "stericsson,ux500-msp-i2s";
+		reg = <0x80125000 0x1000>;
+		interrupts = <0 62 0x4>;
+		v-ape-supply = <&db8500_vape_reg>;
+	};
+
+	codec: ab8500-codec {
+		compatible = "stericsson,ab8500-codec";
+		stericsson,earpeice-cmv = <950>; /* Units in mV. */
+	};
diff --git a/kernel/Documentation/devicetree/bindings/sound/widgets.txt b/kernel/Documentation/devicetree/bindings/sound/widgets.txt
new file mode 100644
index 000000000..b6de5ba3b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/widgets.txt
@@ -0,0 +1,20 @@
+Widgets:
+
+This mainly specifies audio off-codec DAPM widgets.
+
+Each entry is a pair of strings in DT:
+
+	"template-wname", "user-supplied-wname"
+
+The "template-wname" being the template widget name and currently includes:
+"Microphone", "Line", "Headphone" and "Speaker".
+
+The "user-supplied-wname" being the user specified widget name.
+
+For instance:
+	simple-audio-widgets =
+		"Microphone", "Microphone Jack",
+		"Line", "Line In Jack",
+		"Line", "Line Out Jack",
+		"Headphone", "Headphone Jack",
+		"Speaker", "Speaker External";
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8510.txt b/kernel/Documentation/devicetree/bindings/sound/wm8510.txt
new file mode 100644
index 000000000..fa1a32b85
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8510.txt
@@ -0,0 +1,18 @@
+WM8510 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8510"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8510@1a {
+	compatible = "wlf,wm8510";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8523.txt b/kernel/Documentation/devicetree/bindings/sound/wm8523.txt
new file mode 100644
index 000000000..04746186b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8523.txt
@@ -0,0 +1,16 @@
+WM8523 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8523"
+
+  - reg : the I2C address of the device.
+
+Example:
+
+codec: wm8523@1a {
+	compatible = "wlf,wm8523";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8580.txt b/kernel/Documentation/devicetree/bindings/sound/wm8580.txt
new file mode 100644
index 000000000..7d9821f34
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8580.txt
@@ -0,0 +1,16 @@
+WM8580 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8580"
+
+  - reg : the I2C address of the device.
+
+Example:
+
+codec: wm8580@1a {
+	compatible = "wlf,wm8580";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8711.txt b/kernel/Documentation/devicetree/bindings/sound/wm8711.txt
new file mode 100644
index 000000000..8ed9998cd
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8711.txt
@@ -0,0 +1,18 @@
+WM8711 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8711"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8711@1a {
+	compatible = "wlf,wm8711";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8728.txt b/kernel/Documentation/devicetree/bindings/sound/wm8728.txt
new file mode 100644
index 000000000..a8b5c3668
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8728.txt
@@ -0,0 +1,18 @@
+WM8728 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8728"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8728@1a {
+	compatible = "wlf,wm8728";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8731.txt b/kernel/Documentation/devicetree/bindings/sound/wm8731.txt
new file mode 100644
index 000000000..236690e99
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8731.txt
@@ -0,0 +1,27 @@
+WM8731 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8731"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8731@1a {
+	compatible = "wlf,wm8731";
+	reg = <0x1a>;
+};
+
+Available audio endpoints for an audio-routing table:
+ * LOUT: Left Channel Line Output
+ * ROUT: Right Channel Line Output
+ * LHPOUT: Left Channel Headphone Output
+ * RHPOUT: Right Channel Headphone Output
+ * LLINEIN: Left Channel Line Input
+ * RLINEIN: Right Channel Line Input
+ * MICIN: Microphone Input
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8737.txt b/kernel/Documentation/devicetree/bindings/sound/wm8737.txt
new file mode 100644
index 000000000..4bc2cea3b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8737.txt
@@ -0,0 +1,18 @@
+WM8737 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8737"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8737@1a {
+	compatible = "wlf,wm8737";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8741.txt b/kernel/Documentation/devicetree/bindings/sound/wm8741.txt
new file mode 100644
index 000000000..74bda58c1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8741.txt
@@ -0,0 +1,18 @@
+WM8741 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8741"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8741@1a {
+	compatible = "wlf,wm8741";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8750.txt b/kernel/Documentation/devicetree/bindings/sound/wm8750.txt
new file mode 100644
index 000000000..8db239fd5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8750.txt
@@ -0,0 +1,18 @@
+WM8750 and WM8987 audio CODECs
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8750" or "wlf,wm8987"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8750@1a {
+	compatible = "wlf,wm8750";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8753.txt b/kernel/Documentation/devicetree/bindings/sound/wm8753.txt
new file mode 100644
index 000000000..8eee61282
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8753.txt
@@ -0,0 +1,40 @@
+WM8753 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8753"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Pins on the device (for linking into audio routes):
+
+  * LOUT1
+  * LOUT2
+  * ROUT1
+  * ROUT2
+  * MONO1
+  * MONO2
+  * OUT3
+  * OUT4
+  * LINE1
+  * LINE2
+  * RXP
+  * RXN
+  * ACIN
+  * ACOP
+  * MIC1N
+  * MIC1
+  * MIC2N
+  * MIC2
+  * Mic Bias
+
+Example:
+
+codec: wm8753@1a {
+	compatible = "wlf,wm8753";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8770.txt b/kernel/Documentation/devicetree/bindings/sound/wm8770.txt
new file mode 100644
index 000000000..866e00ca1
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8770.txt
@@ -0,0 +1,16 @@
+WM8770 audio CODEC
+
+This device supports SPI.
+
+Required properties:
+
+  - compatible : "wlf,wm8770"
+
+  - reg : the chip select number.
+
+Example:
+
+codec: wm8770@1 {
+	compatible = "wlf,wm8770";
+	reg = <1>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8776.txt b/kernel/Documentation/devicetree/bindings/sound/wm8776.txt
new file mode 100644
index 000000000..3b9ca49ab
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8776.txt
@@ -0,0 +1,18 @@
+WM8776 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8776"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+Example:
+
+codec: wm8776@1a {
+	compatible = "wlf,wm8776";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8804.txt b/kernel/Documentation/devicetree/bindings/sound/wm8804.txt
new file mode 100644
index 000000000..6fd124b16
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8804.txt
@@ -0,0 +1,25 @@
+WM8804 audio CODEC
+
+This device supports both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : "wlf,wm8804"
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+  - PVDD-supply, DVDD-supply : Power supplies for the device, as covered
+    in Documentation/devicetree/bindings/regulator/regulator.txt
+
+Optional properties:
+
+  - wlf,reset-gpio: A GPIO specifier for the GPIO controlling the reset pin
+
+Example:
+
+codec: wm8804@1a {
+	compatible = "wlf,wm8804";
+	reg = <0x1a>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8903.txt b/kernel/Documentation/devicetree/bindings/sound/wm8903.txt
new file mode 100644
index 000000000..94ec32c19
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8903.txt
@@ -0,0 +1,69 @@
+WM8903 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8903"
+
+  - reg : the I2C address of the device.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+
+  - #gpio-cells : Should be two. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+Optional properties:
+
+  - interrupts : The interrupt line the codec is connected to.
+
+  - micdet-cfg : Default register value for R6 (Mic Bias). If absent, the
+    default is 0.
+
+  - micdet-delay : The debounce delay for microphone detection in mS. If
+    absent, the default is 100.
+
+  - gpio-cfg : A list of GPIO configuration register values. The list must
+    be 5 entries long. If absent, no configuration of these registers is
+    performed. If any entry has the value 0xffffffff, that GPIO's
+    configuration will not be modified.
+
+Pins on the device (for linking into audio routes):
+
+  * IN1L
+  * IN1R
+  * IN2L
+  * IN2R
+  * IN3L
+  * IN3R
+  * DMICDAT
+  * HPOUTL
+  * HPOUTR
+  * LINEOUTL
+  * LINEOUTR
+  * LOP
+  * LON
+  * ROP
+  * RON
+  * MICBIAS
+
+Example:
+
+codec: wm8903@1a {
+	compatible = "wlf,wm8903";
+	reg = <0x1a>;
+	interrupts = < 347 >;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	micdet-cfg = <0>;
+	micdet-delay = <100>;
+	gpio-cfg = <
+		0x0600 /* DMIC_LR, output */
+		0x0680 /* DMIC_DAT, input */
+		0x0000 /* GPIO, output, low */
+		0x0200 /* Interrupt, output */
+		0x01a0 /* BCLK, input, active high */
+	>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8904.txt b/kernel/Documentation/devicetree/bindings/sound/wm8904.txt
new file mode 100644
index 000000000..66bf26142
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8904.txt
@@ -0,0 +1,33 @@
+WM8904 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+  - compatible: "wlf,wm8904" or "wlf,wm8912"
+  - reg: the I2C address of the device.
+  - clock-names: "mclk"
+  - clocks: reference to
+    <Documentation/devicetree/bindings/clock/clock-bindings.txt>
+
+Pins on the device (for linking into audio routes):
+
+  * IN1L
+  * IN1R
+  * IN2L
+  * IN2R
+  * IN3L
+  * IN3R
+  * HPOUTL
+  * HPOUTR
+  * LINEOUTL
+  * LINEOUTR
+  * MICBIAS
+
+Examples:
+
+codec: wm8904@1a {
+	compatible = "wlf,wm8904";
+	reg = <0x1a>;
+	clocks = <&pck0>;
+	clock-names = "mclk";
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8960.txt b/kernel/Documentation/devicetree/bindings/sound/wm8960.txt
new file mode 100644
index 000000000..2deb8a3da
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8960.txt
@@ -0,0 +1,31 @@
+WM8960 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8960"
+
+  - reg : the I2C address of the device.
+
+Optional properties:
+  - wlf,shared-lrclk: This is a boolean property. If present, the LRCM bit of
+	R24 (Additional control 2) gets set, indicating that ADCLRC and DACLRC pins
+	will be disabled only when ADC (Left and Right) and DAC (Left and Right)
+	are disabled.
+	When wm8960 works on synchronize mode and DACLRC pin is used to supply
+	frame clock, it will no frame clock for captrue unless enable DAC to enable
+	DACLRC pin. If shared-lrclk is present, no need to enable DAC for captrue.
+
+  - wlf,capless: This is a boolean property. If present, OUT3 pin will be
+	enabled and disabled together with HP_L and HP_R pins in response to jack
+	detect events.
+
+Example:
+
+codec: wm8960@1a {
+	compatible = "wlf,wm8960";
+	reg = <0x1a>;
+
+	wlf,shared-lrclk;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8962.txt b/kernel/Documentation/devicetree/bindings/sound/wm8962.txt
new file mode 100644
index 000000000..7f82b59ec
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8962.txt
@@ -0,0 +1,39 @@
+WM8962 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+  - compatible : "wlf,wm8962"
+
+  - reg : the I2C address of the device.
+
+Optional properties:
+  - spk-mono: This is a boolean property. If present, the SPK_MONO bit
+    of R51 (Class D Control 2) gets set, indicating that the speaker is
+    in mono mode.
+
+  - mic-cfg : Default register value for R48 (Additional Control 4).
+    If absent, the default should be the register default.
+
+  - gpio-cfg : A list of GPIO configuration register values. The list must
+    be 6 entries long. If absent, no configuration of these registers is
+    performed. And note that only the value within [0x0, 0xffff] is valid.
+    Any other value is regarded as setting the GPIO register by its reset
+    value 0x0.
+
+Example:
+
+codec: wm8962@1a {
+	compatible = "wlf,wm8962";
+	reg = <0x1a>;
+
+	gpio-cfg = <
+		0x0000 /* 0:Default */
+		0x0000 /* 1:Default */
+		0x0013 /* 2:FN_DMICCLK */
+		0x0000 /* 3:Default */
+		0x8014 /* 4:FN_DMICCDAT */
+		0x0000 /* 5:Default */
+	>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/sound/wm8994.txt b/kernel/Documentation/devicetree/bindings/sound/wm8994.txt
new file mode 100644
index 000000000..e045e90a0
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/sound/wm8994.txt
@@ -0,0 +1,78 @@
+WM1811/WM8994/WM8958 audio CODEC
+
+These devices support both I2C and SPI (configured with pin strapping
+on the board).
+
+Required properties:
+
+  - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
+
+  - reg : the I2C address of the device for I2C, the chip select
+          number for SPI.
+
+  - gpio-controller : Indicates this device is a GPIO controller.
+  - #gpio-cells : Must be 2. The first cell is the pin number and the
+    second cell is used to specify optional parameters (currently unused).
+
+  - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply,
+    SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered
+    in Documentation/devicetree/bindings/regulator/regulator.txt
+
+Optional properties:
+
+  - interrupts : The interrupt line the IRQ signal for the device is
+    connected to.  This is optional, if it is not connected then none
+    of the interrupt related properties should be specified.
+  - interrupt-controller : These devices contain interrupt controllers
+    and may provide interrupt services to other devices if they have an
+    interrupt line connected.
+  - interrupt-parent : The parent interrupt controller.
+  - #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
+    The first cell is the IRQ number.
+    The second cell is the flags, encoded as the trigger masks from
+    Documentation/devicetree/bindings/interrupts.txt
+
+  - clocks : A list of up to two phandle and clock specifier pairs
+  - clock-names : A list of clock names sorted in the same order as clocks.
+                  Valid clock names are "MCLK1" and "MCLK2".
+
+  - wlf,gpio-cfg : A list of GPIO configuration register values. If absent,
+    no configuration of these registers is performed. If any value is
+    over 0xffff then the register will be left as default. If present 11
+    values must be supplied.
+
+  - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or
+    WM8958.  If absent the register defaults will be used.
+
+  - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device.
+  - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device.
+
+  - wlf,lineout1-se : If present LINEOUT1 is in single ended mode.
+  - wlf,lineout2-se : If present LINEOUT2 is in single ended mode.
+
+  - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback
+    connected.
+  - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback
+    connected.
+
+  - wlf,ldoena-always-driven : If present LDOENA is always driven.
+
+Example:
+
+codec: wm8994@1a {
+	compatible = "wlf,wm8994";
+	reg = <0x1a>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	lineout1-se;
+
+	AVDD2-supply = <&regulator>;
+	CPVDD-supply = <&regulator>;
+	DBVDD1-supply = <&regulator>;
+	DBVDD2-supply = <&regulator>;
+	DBVDD3-supply = <&regulator>;
+	SPKVDD1-supply = <&regulator>;
+	SPKVDD2-supply = <&regulator>;
+};