These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

13 files changed, 179 insertions, 9 deletions

diff --git a/kernel/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt b/kernel/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt
index 34c150577..5d3791e78 100644
--- a/kernel/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt
+++ b/kernel/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt
@@ -5,6 +5,7 @@ Required properties:
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: rtc alarm/event interrupt
+- clocks: phandle to input clock.
 
 Example:
 
@@ -12,4 +13,5 @@ rtc@fffffe00 {
 	compatible = "atmel,at91rm9200-rtc";
 	reg = <0xfffffe00 0x100>;
 	interrupts = <1 4 7>;
+	clocks = <&clk32k>;
 };
diff --git a/kernel/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt b/kernel/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt
new file mode 100644
index 000000000..8e76f2648
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt
@@ -0,0 +1,18 @@
+* Dallas DS1390		SPI Serial Real-Time Clock
+
+Required properties:
+- compatible: Should contain "dallas,ds1390".
+- reg: SPI address for chip
+
+Optional properties:
+- trickle-resistor-ohms : Selected resistor for trickle charger
+	Values usable for ds1390 are 250, 2000, 4000
+	Should be given if trickle charger should be enabled
+- trickle-diode-disable : Do not use internal trickle charger diode
+	Should be given if internal trickle charger diode should be disabled
+Example:
+	ds1390: rtc@68 {
+		compatible = "dallas,ds1390";
+		trickle-resistor-ohms = <250>;
+		reg = <0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt b/kernel/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt
index 5c199ee04..a8934fe2a 100644
--- a/kernel/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt
+++ b/kernel/Documentation/devicetree/bindings/rtc/haoyu,hym8563.txt
@@ -6,11 +6,11 @@ as well as a clock output of up to 32kHz.
 Required properties:
 - compatible: should be: "haoyu,hym8563"
 - reg: i2c address
-- interrupts: rtc alarm/event interrupt
 - #clock-cells: the value should be 0
 
 Optional properties:
 - clock-output-names: From common clock binding
+- interrupts: rtc alarm/event interrupt
 
 Example:
 
diff --git a/kernel/Documentation/devicetree/bindings/rtc/isil,isl12057.txt b/kernel/Documentation/devicetree/bindings/rtc/isil,isl12057.txt
index 501c39cea..cf83e0940 100644
--- a/kernel/Documentation/devicetree/bindings/rtc/isil,isl12057.txt
+++ b/kernel/Documentation/devicetree/bindings/rtc/isil,isl12057.txt
@@ -5,7 +5,7 @@ consisting of a compatible field, an address and possibly an interrupt
 line).
 
 Nonetheless, it also supports an option boolean property
-("isil,irq2-can-wakeup-machine") to handle the specific use-case found
+("wakeup-source") to handle the specific use-case found
 on at least three in-tree users of the chip (NETGEAR ReadyNAS 102, 104
 and 2120 ARM-based NAS); On those devices, the IRQ#2 pin of the chip
 (associated with the alarm supported by the driver) is not connected
@@ -22,9 +22,9 @@ Required properties supported by the device:
 
 Optional properties:
 
- - "isil,irq2-can-wakeup-machine": mark the chip as a wakeup source,
-   independently of the availability of an IRQ line connected to the
-   SoC.
+ - "wakeup-source": mark the chip as a wakeup source, independently of
+    the availability of an IRQ line connected to the SoC.
+    (Legacy property supported: "isil,irq2-can-wakeup-machine")
 
  - "interrupt-parent", "interrupts": for passing the interrupt line
    of the SoC connected to IRQ#2 of the RTC chip.
@@ -74,5 +74,5 @@ PMIC, allowing the device to be started based on configured alarm:
 	isl12057: isl12057@68 {
 		compatible = "isil,isl12057";
 		reg = <0x68>;
-		isil,irq2-can-wakeup-machine;
+		wakeup-source;
 	};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/nxp,lpc1788-rtc.txt b/kernel/Documentation/devicetree/bindings/rtc/nxp,lpc1788-rtc.txt
new file mode 100644
index 000000000..3c97bd180
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/nxp,lpc1788-rtc.txt
@@ -0,0 +1,21 @@
+NXP LPC1788 real-time clock
+
+The LPC1788 RTC provides calendar and clock functionality
+together with periodic tick and alarm interrupt support.
+
+Required properties:
+- compatible	: must contain "nxp,lpc1788-rtc"
+- reg		: Specifies base physical address and size of the registers.
+- interrupts	: A single interrupt specifier.
+- clocks	: Must contain clock specifiers for rtc and register clock
+- clock-names	: Must contain "rtc" and "reg"
+  See ../clocks/clock-bindings.txt for details.
+
+Example:
+rtc: rtc@40046000 {
+	compatible = "nxp,lpc1788-rtc";
+	reg = <0x40046000 0x1000>;
+	interrupts = <47>;
+	clocks = <&creg_clk 0>, <&ccu1 CLK_CPU_BUS>;
+	clock-names = "rtc", "reg";
+};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/pcf8563.txt b/kernel/Documentation/devicetree/bindings/rtc/pcf8563.txt
new file mode 100644
index 000000000..72f6d2c96
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/pcf8563.txt
@@ -0,0 +1,25 @@
+* Philips PCF8563/Epson RTC8564 Real Time Clock
+
+Philips PCF8563/Epson RTC8564 Real Time Clock
+
+Required properties:
+see: Documentation/devicetree/bindings/i2c/trivial-devices.txt
+
+Optional property:
+- #clock-cells: Should be 0.
+- clock-output-names:
+  overwrite the default clock name "pcf8563-clkout"
+
+Example:
+
+pcf8563: pcf8563@51 {
+	compatible = "nxp,pcf8563";
+	reg = <0x51>;
+	#clock-cells = <0>;
+};
+
+device {
+...
+	clocks = <&pcf8563>;
+...
+};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/rtc-mxc.txt b/kernel/Documentation/devicetree/bindings/rtc/rtc-mxc.txt
new file mode 100644
index 000000000..5bcd31d99
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/rtc-mxc.txt
@@ -0,0 +1,26 @@
+* Real Time Clock of the i.MX SoCs
+
+RTC controller for the i.MX SoCs
+
+Required properties:
+- compatible: Should be "fsl,imx1-rtc" or "fsl,imx21-rtc".
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: IRQ line for the RTC.
+- clocks: should contain two entries:
+  * one for the input reference
+  * one for the the SoC RTC
+- clock-names: should contain:
+  * "ref" for the input reference clock
+  * "ipg" for the SoC RTC clock
+
+Example:
+
+rtc@10007000 {
+	compatible = "fsl,imx21-rtc";
+	reg = <0x10007000 0x1000>;
+	interrupts = <22>;
+	clocks = <&clks IMX27_CLK_CKIL>,
+		 <&clks IMX27_CLK_RTC_IPG_GATE>;
+	clock-names = "ref", "ipg";
+};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/kernel/Documentation/devicetree/bindings/rtc/rtc-omap.txt
index 4ba4dbd34..bf7d11ae9 100644
--- a/kernel/Documentation/devicetree/bindings/rtc/rtc-omap.txt
+++ b/kernel/Documentation/devicetree/bindings/rtc/rtc-omap.txt
@@ -8,6 +8,7 @@ Required properties:
 			    Wakeup generation for event Alarm. It can also be
 			    used to control an external PMIC via the
 			    pmic_power_en pin.
+	- "ti,am4372-rtc" - for RTC IP used similar to that on AM437X SoC family.
 - reg: Address range of rtc register set
 - interrupts: rtc timer, alarm interrupts in order
 - interrupt-parent: phandle for the interrupt controller
@@ -15,6 +16,8 @@ Required properties:
 Optional properties:
 - system-power-controller: whether the rtc is controlling the system power
   through pmic_power_en
+- clocks: Any internal or external clocks feeding in to rtc
+- clock-names: Corresponding names of the clocks
 
 Example:
 
@@ -25,4 +28,6 @@ rtc@1c23000 {
 		      19>;
 	interrupt-parent = <&intc>;
 	system-power-controller;
+	clocks = <&clk_32k_rtc>, <&clk_32768_ck>;
+	clock-names = "ext-clk", "int-clk";
 };
diff --git a/kernel/Documentation/devicetree/bindings/rtc/rtc-opal.txt b/kernel/Documentation/devicetree/bindings/rtc/rtc-opal.txt
index af87e5eca..a1734e5cb 100644
--- a/kernel/Documentation/devicetree/bindings/rtc/rtc-opal.txt
+++ b/kernel/Documentation/devicetree/bindings/rtc/rtc-opal.txt
@@ -5,12 +5,13 @@ Required properties:
 - comapatible: Should be "ibm,opal-rtc"
 
 Optional properties:
-- has-tpo: Decides if the wakeup is supported or not.
+- wakeup-source: Decides if the wakeup is supported or not
+		 (Legacy property supported: "has-tpo")
 
 Example:
 	rtc {
 		compatible = "ibm,opal-rtc";
-		has-tpo;
+		wakeup-source;
 		phandle = <0x10000029>;
 		linux,phandle = <0x10000029>;
 	};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt b/kernel/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt
new file mode 100644
index 000000000..daf88265d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt
@@ -0,0 +1,28 @@
+STMicroelectronics Low Power Controller (LPC) - RTC
+===================================================
+
+LPC currently supports Watchdog OR Real Time Clock OR Clocksource
+functionality.
+
+[See: ../watchdog/st_lpc_wdt.txt for Watchdog options]
+[See: ../timer/st,stih407-lpc for Clocksource options]
+
+Required properties
+
+- compatible 	: Must be: "st,stih407-lpc"
+- reg		: LPC registers base address + size
+- interrupts    : LPC interrupt line number and associated flags
+- clocks	: Clock used by LPC device (See: ../clock/clock-bindings.txt)
+- st,lpc-mode	: The LPC can run either one of three modes:
+                  ST_LPC_MODE_RTC    [0]
+                  ST_LPC_MODE_WDT    [1]
+                  ST_LPC_MODE_CLKSRC [2]
+		 One (and only one) mode must be selected.
+
+Example:
+	lpc@fde05000 {
+		compatible	= "st,stih407-lpc";
+		reg		= <0xfde05000 0x1000>;
+		clocks 		= <&clk_s_d3_flexgen CLK_LPC_0>;
+		st,lpc-mode	= <ST_LPC_MODE_RTC>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/kernel/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
index ab757b84d..ac2fcd6ff 100644
--- a/kernel/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
+++ b/kernel/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
@@ -6,7 +6,8 @@ Required properties:
     * "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc.
     * "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc.
     * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
-    * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc.
+    * "samsung,exynos3250-rtc" - (deprecated) for controllers compatible with
+                                 exynos3250 rtc (use "samsung,s3c6410-rtc").
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: Two interrupt numbers to the cpu should be specified. First
diff --git a/kernel/Documentation/devicetree/bindings/rtc/ti,bq32k.txt b/kernel/Documentation/devicetree/bindings/rtc/ti,bq32k.txt
new file mode 100644
index 000000000..e204906b9
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/ti,bq32k.txt
@@ -0,0 +1,18 @@
+* TI BQ32000                I2C Serial Real-Time Clock
+
+Required properties:
+- compatible: Should contain "ti,bq32000".
+- reg: I2C address for chip
+
+Optional properties:
+- trickle-resistor-ohms : Selected resistor for trickle charger
+       Values usable are 1120 and 20180
+       Should be given if trickle charger should be enabled
+- trickle-diode-disable : Do not use internal trickle charger diode
+       Should be given if internal trickle charger diode should be disabled
+Example:
+       bq32000: rtc@68 {
+               compatible = "ti,bq32000";
+               trickle-resistor-ohms = <1120>;
+               reg = <0x68>;
+       };
diff --git a/kernel/Documentation/devicetree/bindings/rtc/xlnx-rtc.txt b/kernel/Documentation/devicetree/bindings/rtc/xlnx-rtc.txt
new file mode 100644
index 000000000..0df6f016b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/rtc/xlnx-rtc.txt
@@ -0,0 +1,25 @@
+* Xilinx Zynq Ultrascale+ MPSoC Real Time Clock
+
+RTC controller for the Xilinx Zynq MPSoC Real Time Clock
+Separate IRQ lines for seconds and alarm
+
+Required properties:
+- compatible: Should be "xlnx,zynqmp-rtc"
+- reg: Physical base address of the controller and length
+       of memory mapped region.
+- interrupts: IRQ lines for the RTC.
+- interrupt-names: interrupt line names eg. "sec" "alarm"
+
+Optional:
+- calibration: calibration value for 1 sec period which will
+		be programmed directly to calibration register
+
+Example:
+rtc: rtc@ffa60000 {
+	compatible = "xlnx,zynqmp-rtc";
+	reg = <0x0 0xffa60000 0x100>;
+	interrupt-parent = <&gic>;
+	interrupts = <0 26 4>, <0 27 4>;
+	interrupt-names = "alarm", "sec";
+	calibration = <0x198233>;
+};