These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

4 files changed, 190 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt b/kernel/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt
new file mode 100644
index 000000000..862f4a49d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt
@@ -0,0 +1,34 @@
+AXP20x USB power supply
+
+Required Properties:
+-compatible: "x-powers,axp202-usb-power-supply"
+
+This node is a subnode of the axp20x PMIC.
+
+Example:
+
+axp209: pmic@34 {
+	compatible = "x-powers,axp209";
+	reg = <0x34>;
+	interrupt-parent = <&nmi_intc>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	regulators {
+		x-powers,dcdc-freq = <1500>;
+
+		vdd_cpu: dcdc2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1450000>;
+			regulator-name = "vdd-cpu";
+		};
+
+		...
+	};
+
+	usb-power-supply: usb-power-supply {
+		compatible = "x-powers,axp202-usb-power-supply";
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/power_supply/max17042_battery.txt b/kernel/Documentation/devicetree/bindings/power_supply/max17042_battery.txt
index 5bc9b685c..3f3894aae 100644
--- a/kernel/Documentation/devicetree/bindings/power_supply/max17042_battery.txt
+++ b/kernel/Documentation/devicetree/bindings/power_supply/max17042_battery.txt
@@ -9,10 +9,23 @@ Optional properties :
                          (datasheet-recommended value is 10000).
    Defining this property enables current-sense functionality.
 
+Optional threshold properties :
+ If skipped the condition won't be reported.
+ - maxim,cold-temp :      Temperature threshold to report battery
+                          as cold (in tenths of degree Celsius).
+ - maxim,over-heat-temp : Temperature threshold to report battery
+                          as over heated (in tenths of degree Celsius).
+ - maxim,dead-volt :      Voltage threshold to report battery
+                          as dead (in mV).
+ - maxim,over-volt :      Voltage threshold to report battery
+                          as over voltage (in mV).
+
 Example:
 
 	battery-charger@36 {
 		compatible = "maxim,max17042";
 		reg = <0x36>;
 		maxim,rsns-microohm = <10000>;
+		maxim,over-heat-temp = <600>;
+		maxim,over-volt = <4300>;
 	};
diff --git a/kernel/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/kernel/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
new file mode 100644
index 000000000..65b88fac8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
@@ -0,0 +1,131 @@
+Qualcomm Switch-Mode Battery Charger and Boost
+
+PROPERTIES
+- compatible:
+  Usage: required
+  Value type: <stringlist>
+  Description: Must be one of:
+               - "qcom,pm8941-charger"
+
+- reg:
+  Usage: required
+  Value type: <prop-encoded-array>
+  Description: Base address of registers for SMBB block
+
+- interrupts:
+  Usage: required
+  Value type: <prop-encoded-array>
+  Description: The format of the specifier is defined by the binding document
+               describing the node's interrupt parent.  Must contain one
+               specifier for each of the following interrupts, in order:
+               - charge done
+               - charge fast mode
+               - charge trickle mode
+               - battery temperature ok
+               - battery present
+               - charger disconnected
+               - USB-in valid
+               - DC-in valid
+
+- interrupt-names:
+  Usage: required
+  Value type: <stringlist>
+  Description: Must contain the following list, strictly ordered:
+               "chg-done",
+               "chg-fast",
+               "chg-trkl",
+               "bat-temp-ok",
+               "bat-present",
+               "chg-gone",
+               "usb-valid",
+               "dc-valid"
+
+- qcom,fast-charge-current-limit:
+  Usage: optional (default: 1A, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 3A]
+  Description: Maximum charge current; May be clamped to safety limits.
+
+- qcom,fast-charge-low-threshold-voltage:
+  Usage: optional (default: 3.2V, or pre-configured value)
+  Value type: <u32>; uV; range [2.1V : 3.6V]
+  Description: Battery voltage limit above which fast charging may operate;
+               Below this value linear or switch-mode auto-trickle-charging
+               will operate.
+
+- qcom,fast-charge-high-threshold-voltage:
+  Usage: optional (default: 4.2V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Battery voltage limit below which fast charging may operate;
+               The fast charger will attempt to charge the battery to this
+               voltage.  May be clamped to safety limits.
+
+- qcom,fast-charge-safe-voltage:
+  Usage: optional (default: 4.2V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Maximum safe battery voltage; May be pre-set by bootloader, in
+               which case, setting this will harmlessly fail. The property
+               'fast-charge-high-watermark' will be clamped by this value.
+
+- qcom,fast-charge-safe-current:
+  Usage: optional (default: 1A, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 3A]
+  Description: Maximum safe battery charge current; May pre-set by bootloader,
+               in which case, setting this will harmlessly fail. The property
+               'qcom,fast-charge-current-limit' will be clamped by this value.
+
+- qcom,auto-recharge-threshold-voltage:
+  Usage: optional (default: 4.1V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Battery voltage limit below which auto-recharge functionality
+               will restart charging after end-of-charge;  The high cutoff
+               limit for auto-recharge is 5% above this value.
+
+- qcom,minimum-input-voltage:
+  Usage: optional (default: 4.3V, or pre-configured value)
+  Value type: <u32>; uV; range [4.2V : 9.6V]
+  Description: Input voltage level above which charging may operate
+
+- qcom,dc-current-limit:
+  Usage: optional (default: 100mA, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 2.5A]
+  Description: Default DC charge current limit
+
+- qcom,disable-dc:
+  Usage: optional (default: false)
+  Value type: boolean: <u32> or <empty>
+  Description: Disable DC charger
+
+- qcom,jeita-extended-temp-range:
+  Usage: optional (default: false)
+  Value type: boolean: <u32> or <empty>
+  Description: Enable JEITA extended temperature range;  This does *not*
+               adjust the maximum charge voltage or current in the extended
+               temperature range.  It only allows charging when the battery
+               is in the extended temperature range.  Voltage/current
+               regulation must be done externally to fully comply with
+               the JEITA safety guidelines if this flag is set.
+
+EXAMPLE
+charger@1000 {
+       compatible = "qcom,pm8941-charger";
+       reg = <0x1000 0x700>;
+       interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+       interrupt-names = "chg-done",
+                       "chg-fast",
+                       "chg-trkl",
+                       "bat-temp-ok",
+                       "bat-present",
+                       "chg-gone",
+                       "usb-valid",
+                       "dc-valid";
+
+       qcom,fast-charge-current-limit = <1000000>;
+       qcom,dc-charge-current-limit = <1000000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt b/kernel/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt
new file mode 100644
index 000000000..98d131ace
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt
@@ -0,0 +1,12 @@
+TPS65217 Charger
+
+Required Properties:
+-compatible: "ti,tps65217-charger"
+
+This node is a subnode of the tps65217 PMIC.
+
+Example:
+
+	tps65217-charger {
+		compatible = "ti,tps65090-charger";
+	};