These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

11 files changed, 377 insertions, 26 deletions

diff --git a/kernel/Documentation/devicetree/bindings/power/bq24257.txt b/kernel/Documentation/devicetree/bindings/power/bq24257.txt
new file mode 100644
index 000000000..d693702c9
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/bq24257.txt
@@ -0,0 +1,64 @@
+Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24250"
+ * "ti,bq24251"
+ * "ti,bq24257"
+- reg: integer, i2c address of the device.
+- interrupt-parent: Should be the phandle for the interrupt controller. Use in
+    conjunction with "interrupts".
+- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
+    conjunction with "interrupt-parent".
+- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+    constant-voltage phase drops below this value (in uA).
+
+Optional properties:
+- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
+    This pin is not available on all devices however it should be used if
+    possible as this is the recommended way to obtain the charger's input PG
+    state. If this pin is not specified a software-based approach for PG
+    detection is used.
+- ti,current-limit: The maximum current to be drawn from the charger's input
+    (in uA). If this property is not specified, the input limit current is
+    set automatically using USB D+/D- signal based charger type detection.
+    If the hardware does not support the D+/D- based detection, a default
+    of 500,000 is used (=500mA) instead.
+- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
+    not specified a default of 6,5000,000 (=6.5V) is used.
+- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
+    power path management (in uV). If not specified a default of 4,360,000
+    (=4.36V) is used.
+
+Example:
+
+bq24257 {
+	compatible = "ti,bq24257";
+	reg = <0x6a>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+	pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+	ti,battery-regulation-voltage = <4200000>;
+	ti,charge-current = <1000000>;
+	ti,termination-current = <50000>;
+};
+
+Example:
+
+bq24250 {
+	compatible = "ti,bq24250";
+	reg = <0x6a>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+	ti,battery-regulation-voltage = <4200000>;
+	ti,charge-current = <500000>;
+	ti,termination-current = <50000>;
+	ti,current-limit = <900000>;
+	ti,ovp-voltage = <9500000>;
+	ti,in-dpm-voltage = <4440000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/power/bq25890.txt b/kernel/Documentation/devicetree/bindings/power/bq25890.txt
new file mode 100644
index 000000000..c9dd17d14
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/bq25890.txt
@@ -0,0 +1,46 @@
+Binding for TI bq25890 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+    * "ti,bq25890"
+- reg: integer, i2c address of the device.
+- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
+- ti,charge-current: integer, maximum charging current (in uA);
+- ti,termination-current: integer, charge will be terminated when current in
+    constant-voltage phase drops below this value (in uA);
+- ti,precharge-current: integer, maximum charge current during precharge
+    phase (in uA);
+- ti,minimum-sys-voltage: integer, when battery is charging and it is below
+    minimum system voltage, the system will be regulated above
+    minimum-sys-voltage setting (in uV);
+- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
+- ti,boost-max-current: integer, maximum allowed current draw in boost mode
+    (in uA).
+
+Optional properties:
+- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
+    otherwise 1.5MHz;
+- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
+    input current will be the lower between the resistor setting and the IINLIM
+    register setting;
+- ti,thermal-regulation-threshold: integer, temperature above which the charge
+    current is lowered, to avoid overheating (in degrees Celsius). If omitted,
+    the default setting will be used (120 degrees);
+
+Example:
+
+bq25890 {
+        compatible = "ti,bq25890";
+        reg = <0x6a>;
+
+        ti,battery-regulation-voltage = <4200000>;
+        ti,charge-current = <1000000>;
+        ti,termination-current = <50000>;
+        ti,precharge-current = <128000>;
+        ti,minimum-sys-voltage = <3600000>;
+        ti,boost-voltage = <5000000>;
+        ti,boost-max-current = <1000000>;
+
+        ti,use-ilim-pin;
+        ti,thermal-regulation-threshold = <120>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/power/da9150-fg.txt b/kernel/Documentation/devicetree/bindings/power/da9150-fg.txt
new file mode 100644
index 000000000..00236fe3e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/da9150-fg.txt
@@ -0,0 +1,23 @@
+Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings
+
+Required properties:
+- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply
+
+Optional properties:
+- dlg,update-interval: Interval time (milliseconds) between battery level checks.
+- dlg,warn-soc-level: Battery discharge level (%) where warning event raised.
+      [1 - 100]
+- dlg,crit-soc-level: Battery discharge level (%) where critical event raised.
+  This value should be lower than the warning level.
+      [1 - 100]
+
+
+Example:
+
+	fuel-gauge {
+		compatible = "dlg,da9150-fuel-gauge";
+
+		dlg,update-interval = <10000>;
+		dlg,warn-soc-level = /bits/ 8 <15>;
+		dlg,crit-soc-level = /bits/ 8 <5>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/power/opp.txt b/kernel/Documentation/devicetree/bindings/power/opp.txt
deleted file mode 100644
index 74499e503..000000000
--- a/kernel/Documentation/devicetree/bindings/power/opp.txt
+++ /dev/null
@@ -1,25 +0,0 @@
-* Generic OPP Interface
-
-SoCs have a standard set of tuples consisting of frequency and
-voltage pairs that the device will support per voltage domain. These
-are called Operating Performance Points or OPPs.
-
-Properties:
-- operating-points: An array of 2-tuples items, and each item consists
-  of frequency and voltage like <freq-kHz vol-uV>.
-	freq: clock frequency in kHz
-	vol: voltage in microvolt
-
-Examples:
-
-cpu@0 {
-	compatible = "arm,cortex-a9";
-	reg = <0>;
-	next-level-cache = <&L2>;
-	operating-points = <
-		/* kHz    uV */
-		792000  1100000
-		396000  950000
-		198000  850000
-	>;
-};
diff --git a/kernel/Documentation/devicetree/bindings/power/pd-samsung.txt b/kernel/Documentation/devicetree/bindings/power/pd-samsung.txt
new file mode 100644
index 000000000..4e947372a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/pd-samsung.txt
@@ -0,0 +1,52 @@
+* Samsung Exynos Power Domains
+
+Exynos processors include support for multiple power domains which are used
+to gate power to one or more peripherals on the processor.
+
+Required Properties:
+- compatible: should be one of the following.
+    * samsung,exynos4210-pd - for exynos4210 type power domain.
+- reg: physical base address of the controller and length of memory mapped
+    region.
+- #power-domain-cells: number of cells in power domain specifier;
+    must be 0.
+
+Optional Properties:
+- clocks: List of clock handles. The parent clocks of the input clocks to the
+	devices in this power domain are set to oscclk before power gating
+	and restored back after powering on a domain. This is required for
+	all domains which are powered on and off and not required for unused
+	domains.
+- clock-names: The following clocks can be specified:
+	- oscclk: Oscillator clock.
+	- clkN: Input clocks to the devices in this power domain. These clocks
+		will be reparented to oscclk before swithing power domain off.
+		Their original parent will be brought back after turning on
+		the domain. Maximum of 4 clocks (N = 0 to 3) are supported.
+	- asbN: Clocks required by asynchronous bridges (ASB) present in
+		the power domain. These clock should be enabled during power
+		domain on/off operations.
+- power-domains: phandle pointing to the parent power domain, for more details
+		 see Documentation/devicetree/bindings/power/power_domain.txt
+
+Node of a device using power domains must have a power-domains property
+defined with a phandle to respective power domain.
+
+Example:
+
+	lcd0: power-domain-lcd0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023C00 0x10>;
+		#power-domain-cells = <0>;
+	};
+
+	mfc_pd: power-domain@10044060 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10044060 0x20>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MOUT_USER_ACLK333>;
+		clock-names = "oscclk", "clk0";
+		#power-domain-cells = <0>;
+	};
+
+See Documentation/devicetree/bindings/power/power_domain.txt for description
+of consumer-side bindings.
diff --git a/kernel/Documentation/devicetree/bindings/power/power_domain.txt b/kernel/Documentation/devicetree/bindings/power/power_domain.txt
index 0f8ed3710..025b5e7df 100644
--- a/kernel/Documentation/devicetree/bindings/power/power_domain.txt
+++ b/kernel/Documentation/devicetree/bindings/power/power_domain.txt
@@ -48,7 +48,7 @@ Example 2:
 		#power-domain-cells = <1>;
 	};
 
-	child: power-controller@12340000 {
+	child: power-controller@12341000 {
 		compatible = "foo,power-controller";
 		reg = <0x12341000 0x1000>;
 		power-domains = <&parent 0>;
diff --git a/kernel/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt b/kernel/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt
new file mode 100644
index 000000000..0e6d8754e
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt
@@ -0,0 +1,48 @@
+Qualcomm Coincell Charger:
+
+The hardware block controls charging for a coincell or capacitor that is
+used to provide power backup for certain features of the power management
+IC (PMIC)
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be: "qcom,pm8941-coincell"
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: base address of the coincell charger registers
+
+- qcom,rset-ohms:
+	Usage: required
+	Value type: <u32>
+	Definition: resistance (in ohms) for current-limiting resistor
+		must be one of: 800, 1200, 1700, 2100
+
+- qcom,vset-millivolts:
+	Usage: required
+	Value type: <u32>
+	Definition: voltage (in millivolts) to apply for charging
+		must be one of: 2500, 3000, 3100, 3200
+
+- qcom,charger-disable:
+	Usage: optional
+	Value type: <boolean>
+	Definition: definining this property disables charging
+
+This charger is a sub-node of one of the 8941 PMIC blocks, and is specified
+as a child node in DTS of that node.  See ../mfd/qcom,spmi-pmic.txt and
+../mfd/qcom-pm8xxx.txt
+
+Example:
+
+	pm8941@0 {
+		coincell@2800 {
+			compatible = "qcom,pm8941-coincell";
+			reg = <0x2800>;
+
+			qcom,rset-ohms = <2100>;
+			qcom,vset-millivolts = <3000>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/kernel/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
index 8b70db103..b8627e763 100644
--- a/kernel/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
+++ b/kernel/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
@@ -33,6 +33,8 @@ Required properties:
 - compatible: should be one of:
   - "rockchip,rk3188-io-voltage-domain" for rk3188
   - "rockchip,rk3288-io-voltage-domain" for rk3288
+  - "rockchip,rk3368-io-voltage-domain" for rk3368
+  - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains
 - rockchip,grf: phandle to the syscon managing the "general register files"
 
 
@@ -64,6 +66,18 @@ Possible supplies for rk3288:
 - sdcard-supply: The supply connected to SDMMC0_VDD.
 - wifi-supply:   The supply connected to APIO3_VDD.  Also known as SDIO0.
 
+Possible supplies for rk3368:
+- audio-supply:  The supply connected to APIO3_VDD.
+- dvp-supply:    The supply connected to DVPIO_VDD.
+- flash0-supply: The supply connected to FLASH0_VDD.  Typically for eMMC
+- gpio30-supply: The supply connected to APIO1_VDD.
+- gpio1830       The supply connected to APIO4_VDD.
+- sdcard-supply: The supply connected to SDMMC0_VDD.
+- wifi-supply:   The supply connected to APIO2_VDD.  Also known as SDIO0.
+
+Possible supplies for rk3368 pmu-domains:
+- pmu-supply:    The supply connected to PMUIO_VDD.
+- vop-supply:    The supply connected to LCDC_VDD.
 
 Example:
 
diff --git a/kernel/Documentation/devicetree/bindings/power/rt9455_charger.txt b/kernel/Documentation/devicetree/bindings/power/rt9455_charger.txt
new file mode 100644
index 000000000..5d9ad5cf2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/rt9455_charger.txt
@@ -0,0 +1,48 @@
+Binding for Richtek rt9455 battery charger
+
+Required properties:
+- compatible:				it should contain one of the following:
+					"richtek,rt9455".
+- reg:					integer, i2c address of the device.
+- interrupt-parent:			the phandle for the interrupt controller that
+					services interrupts for this device.
+- interrupts:				interrupt mapping for GPIO IRQ, it should be
+					configured with IRQ_TYPE_LEVEL_LOW flag.
+- richtek,output-charge-current:	integer, output current from the charger to the
+					battery, in uA.
+- richtek,end-of-charge-percentage:	integer, percent of the output charge current.
+					When the current in constant-voltage phase drops
+					below output_charge_current x end-of-charge-percentage,
+					charge is terminated.
+- richtek,battery-regulation-voltage:	integer, maximum battery voltage in uV.
+- richtek,boost-output-voltage:		integer, maximum voltage provided to consumer
+					devices, when the charger is in boost mode, in uV.
+
+Optional properties:
+- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to
+					decrease voltage level when the over current
+					of the input power source occurs.
+					This prevents input voltage drop due to insufficient
+					current provided by the power source.
+					Default: 4500000 uV (4.5V)
+- richtek,avg-input-current-regulation: integer, input current value in uA drained by the
+					charger from the power source.
+					Default: 500000 uA (500mA)
+
+Example:
+
+rt9455@22 {
+	compatible = "richtek,rt9455";
+	reg = <0x22>;
+
+	interrupt-parent = <&gpio1>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+	richtek,output-charge-current	    = <500000>;
+	richtek,end-of-charge-percentage    = <10>;
+	richtek,battery-regulation-voltage  = <4200000>;
+	richtek,boost-output-voltage	    = <5050000>;
+
+	richtek,min-input-voltage-regulation = <4500000>;
+	richtek,avg-input-current-regulation = <500000>;
+};
diff --git a/kernel/Documentation/devicetree/bindings/power/twl-charger.txt b/kernel/Documentation/devicetree/bindings/power/twl-charger.txt
index d5c706216..3b4ea1b73 100644
--- a/kernel/Documentation/devicetree/bindings/power/twl-charger.txt
+++ b/kernel/Documentation/devicetree/bindings/power/twl-charger.txt
@@ -1,5 +1,15 @@
 TWL BCI (Battery Charger Interface)
 
+The battery charger needs to interact with the USB phy in order
+to know when charging is permissible, and when there is a connection
+or disconnection.
+
+The choice of phy cannot be configured at a hardware level, so there
+is no value in explicit configuration in device-tree.  Rather
+if there is a sibling of the BCI node which is compatible with
+"ti,twl4030-usb", then that is used to determine when and how
+use USB power for charging.
+
 Required properties:
 - compatible:
   - "ti,twl4030-bci"
diff --git a/kernel/Documentation/devicetree/bindings/power/wakeup-source.txt b/kernel/Documentation/devicetree/bindings/power/wakeup-source.txt
new file mode 100644
index 000000000..963c6dfd4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/power/wakeup-source.txt
@@ -0,0 +1,71 @@
+Specifying wakeup capability for devices
+============================================
+
+Any device nodes
+----------------
+Nodes that describe devices which has wakeup capability must contain an
+"wakeup-source" boolean property.
+
+Also, if device is marked as a wakeup source, then all the primary
+interrupt(s) can be used as wakeup interrupt(s).
+
+However if the devices have dedicated interrupt as the wakeup source
+then they need to specify/identify the same using device specific
+interrupt name. In such cases only that interrupt can be used as wakeup
+interrupt.
+
+List of legacy properties and respective binding document
+---------------------------------------------------------
+
+1. "enable-sdio-wakeup"		Documentation/devicetree/bindings/mmc/mmc.txt
+2. "gpio-key,wakeup"		Documentation/devicetree/bindings/input/gpio-keys{,-polled}.txt
+3. "has-tpo"			Documentation/devicetree/bindings/rtc/rtc-opal.txt
+4. "isil,irq2-can-wakeup-machine" Documentation/devicetree/bindings/rtc/isil,isl12057.txt
+5. "linux,wakeup"		Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt
+				Documentation/devicetree/bindings/mfd/tc3589x.txt
+				Documentation/devicetree/bindings/input/ads7846.txt
+6. "linux,keypad-wakeup"	Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt
+7. "linux,input-wakeup"		Documentation/devicetree/bindings/input/samsung-keypad.txt
+8. "nvidia,wakeup-source"	Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt
+
+Examples
+--------
+
+1. With "wakeup" interrupt name
+
+	device@10000 {
+		compatible	= "vendor,device-id";
+		reg		= <0x10000 0x1000>;
+		interrupts	= <0 19 4>, <0 21 4>, <0 22 4>;
+		interrupt-names	= "ack", "err", "wakeup";
+		wakeup-source;
+	};
+
+2. Without "wakeup" interrupt name
+
+	embedded-controller {
+		compatible = "google,cros-ec-i2c";
+		reg = <0x1e>;
+		interrupts = <6 0>;
+		interrupt-parent = <&gpx1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ec_irq>;
+		wakeup-source;
+	};
+
+3. Without interrupts
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@1 {
+			debounce_interval = <50>;
+			wakeup-source;
+			linux,code = <116>;
+			label = "POWER";
+			gpios = <&iofpga_gpio0 0 0x4>;
+		};
+		[....]
+	};