These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

32 files changed, 805 insertions, 70 deletions

diff --git a/kernel/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/kernel/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
deleted file mode 100644
index 8db32384a..000000000
--- a/kernel/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ /dev/null
@@ -1,48 +0,0 @@
-* AMD 10GbE PHY driver (amd-xgbe-phy)
-
-Required properties:
-- compatible: Should be "amd,xgbe-phy-seattle-v1a" and
-  "ethernet-phy-ieee802.3-c45"
-- reg: Address and length of the register sets for the device
-   - SerDes Rx/Tx registers
-   - SerDes integration registers (1/2)
-   - SerDes integration registers (2/2)
-- interrupt-parent: Should be the phandle for the interrupt controller
-  that services interrupts for this device
-- interrupts: Should contain the amd-xgbe-phy interrupt.
-
-Optional properties:
-- amd,speed-set: Speed capabilities of the device
-    0 - 1GbE and 10GbE (default)
-    1 - 2.5GbE and 10GbE
-
-The following optional properties are represented by an array with each
-value corresponding to a particular speed. The first array value represents
-the setting for the 1GbE speed, the second value for the 2.5GbE speed and
-the third value for the 10GbE speed.  All three values are required if the
-property is used.
-- amd,serdes-blwc: Baseline wandering correction enablement
-    0 - Off
-    1 - On
-- amd,serdes-cdr-rate: CDR rate speed selection
-- amd,serdes-pq-skew: PQ (data sampling) skew
-- amd,serdes-tx-amp: TX amplitude boost
-- amd,serdes-dfe-tap-config: DFE taps available to run
-- amd,serdes-dfe-tap-enable: DFE taps to enable
-
-Example:
-	xgbe_phy@e1240800 {
-		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
-		reg = <0 0xe1240800 0 0x00400>,
-		      <0 0xe1250000 0 0x00060>,
-		      <0 0xe1250080 0 0x00004>;
-		interrupt-parent = <&gic>;
-		interrupts = <0 323 4>;
-		amd,speed-set = <0>;
-		amd,serdes-blwc = <1>, <1>, <0>;
-		amd,serdes-cdr-rate = <2>, <2>, <7>;
-		amd,serdes-pq-skew = <10>, <10>, <30>;
-		amd,serdes-tx-amp = <15>, <15>, <10>;
-		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
-		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
-	};
diff --git a/kernel/Documentation/devicetree/bindings/net/amd-xgbe.txt b/kernel/Documentation/devicetree/bindings/net/amd-xgbe.txt
index 26efd526d..4bb624a73 100644
--- a/kernel/Documentation/devicetree/bindings/net/amd-xgbe.txt
+++ b/kernel/Documentation/devicetree/bindings/net/amd-xgbe.txt
@@ -5,12 +5,16 @@ Required properties:
 - reg: Address and length of the register sets for the device
    - MAC registers
    - PCS registers
+   - SerDes Rx/Tx registers
+   - SerDes integration registers (1/2)
+   - SerDes integration registers (2/2)
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
 - interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt
   listed is required and is the general device interrupt. If the optional
   amd,per-channel-interrupt property is specified, then one additional
-  interrupt for each DMA channel supported by the device should be specified
+  interrupt for each DMA channel supported by the device should be specified.
+  The last interrupt listed should be the PCS auto-negotiation interrupt.
 - clocks:
    - DMA clock for the amd-xgbe device (used for calculating the
      correct Rx interrupt watchdog timer value on a DMA channel
@@ -19,7 +23,6 @@ Required properties:
 - clock-names: Should be the names of the clocks
    - "dma_clk" for the DMA clock
    - "ptp_clk" for the PTP clock
-- phy-handle: See ethernet.txt file in the same directory
 - phy-mode: See ethernet.txt file in the same directory
 
 Optional properties:
@@ -29,19 +32,46 @@ Optional properties:
 - amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate
   a unique interrupt for each DMA channel - this requires an additional
   interrupt be configured for each DMA channel
+- amd,speed-set: Speed capabilities of the device
+    0 - 1GbE and 10GbE (default)
+    1 - 2.5GbE and 10GbE
+
+The following optional properties are represented by an array with each
+value corresponding to a particular speed. The first array value represents
+the setting for the 1GbE speed, the second value for the 2.5GbE speed and
+the third value for the 10GbE speed.  All three values are required if the
+property is used.
+- amd,serdes-blwc: Baseline wandering correction enablement
+    0 - Off
+    1 - On
+- amd,serdes-cdr-rate: CDR rate speed selection
+- amd,serdes-pq-skew: PQ (data sampling) skew
+- amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
 
 Example:
 	xgbe@e0700000 {
 		compatible = "amd,xgbe-seattle-v1a";
 		reg = <0 0xe0700000 0 0x80000>,
-		      <0 0xe0780000 0 0x80000>;
+		      <0 0xe0780000 0 0x80000>,
+		      <0 0xe1240800 0 0x00400>,
+		      <0 0xe1250000 0 0x00060>,
+		      <0 0xe1250080 0 0x00004>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 325 4>,
-			     <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>;
+			     <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>,
+			     <0 323 4>;
 		amd,per-channel-interrupt;
 		clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
 		clock-names = "dma_clk", "ptp_clk";
-		phy-handle = <&phy>;
 		phy-mode = "xgmii";
 		mac-address = [ 02 a1 a2 a3 a4 a5 ];
+		amd,speed-set = <0>;
+		amd,serdes-blwc = <1>, <1>, <0>;
+		amd,serdes-cdr-rate = <2>, <2>, <7>;
+		amd,serdes-pq-skew = <10>, <10>, <30>;
+		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
 	};
diff --git a/kernel/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/kernel/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
index f55aa280d..078060a97 100644
--- a/kernel/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
+++ b/kernel/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
@@ -37,6 +37,14 @@ Required properties for ethernet interfaces that have external PHY:
 
 Optional properties:
 - status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok".
+- tx-delay: Delay value for RGMII bridge TX clock.
+	    Valid values are between 0 to 7, that maps to
+	    417, 717, 1020, 1321, 1611, 1913, 2215, 2514 ps
+	    Default value is 4, which corresponds to 1611 ps
+- rx-delay: Delay value for RGMII bridge RX clock.
+	    Valid values are between 0 to 7, that maps to
+	    273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps
+	    Default value is 2, which corresponds to 899 ps
 
 Example:
 	menetclk: menetclk {
@@ -72,5 +80,7 @@ Example:
 
 /* Board-specific peripheral configurations */
 &menet {
+	tx-delay = <4>;
+	rx-delay = <2>;
         status = "ok";
 };
diff --git a/kernel/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt b/kernel/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt
new file mode 100644
index 000000000..8ba9ed11d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt
@@ -0,0 +1,23 @@
+* Broadcom iProc MDIO bus controller
+
+Required properties:
+- compatible: should be "brcm,iproc-mdio"
+- reg: address and length of the register set for the MDIO interface
+- #size-cells: must be 1
+- #address-cells: must be 0
+
+Child nodes of this MDIO bus controller node are standard Ethernet PHY device
+nodes as described in Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+
+mdio@18002000 {
+	compatible = "brcm,iproc-mdio";
+	reg = <0x18002000 0x8>;
+	#size-cells = <1>;
+	#address-cells = <0>;
+
+	enet-gphy@0 {
+		reg = <0>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/can/sun4i_can.txt b/kernel/Documentation/devicetree/bindings/net/can/sun4i_can.txt
new file mode 100644
index 000000000..84ed1909d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/can/sun4i_can.txt
@@ -0,0 +1,36 @@
+Allwinner A10/A20 CAN controller Device Tree Bindings
+-----------------------------------------------------
+
+Required properties:
+- compatible: "allwinner,sun4i-a10-can"
+- reg: physical base address and size of the Allwinner A10/A20 CAN register map.
+- interrupts: interrupt specifier for the sole interrupt.
+- clock: phandle and clock specifier.
+
+Example
+-------
+
+SoC common .dtsi file:
+
+	can0_pins_a: can0@0 {
+		allwinner,pins = "PH20","PH21";
+		allwinner,function = "can";
+		allwinner,drive = <0>;
+		allwinner,pull = <0>;
+	};
+...
+	can0: can@01c2bc00 {
+		compatible = "allwinner,sun4i-a10-can";
+		reg = <0x01c2bc00 0x400>;
+		interrupts = <0 26 4>;
+		clocks = <&apb1_gates 4>;
+		status = "disabled";
+	};
+
+Board specific .dts file:
+
+	can0: can@01c2bc00 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&can0_pins_a>;
+		status = "okay";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/cpsw.txt b/kernel/Documentation/devicetree/bindings/net/cpsw.txt
index 33fe8462e..28a4781ab 100644
--- a/kernel/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/kernel/Documentation/devicetree/bindings/net/cpsw.txt
@@ -2,7 +2,11 @@ TI SoC Ethernet Switch Controller Device Tree Bindings
 ------------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,cpsw"
+- compatible		: Should be one of the below:-
+			  "ti,cpsw" for backward compatible
+			  "ti,am335x-cpsw" for AM335x controllers
+			  "ti,am4372-cpsw" for AM437x controllers
+			  "ti,dra7-cpsw" for DRA7x controllers
 - reg			: physical base address and size of the cpsw
 			  registers map
 - interrupts		: property with a value describing the interrupt
@@ -26,15 +30,28 @@ Optional properties:
 - dual_emac		: Specifies Switch to act as Dual EMAC
 - syscon		: Phandle to the system control device node, which is
 			  the control module device of the am33x
+- mode-gpios		: Should be added if one/multiple gpio lines are
+			  required to be driven so that cpsw data lines
+			  can be connected to the phy via selective mux.
+			  For example in dra72x-evm, pcf gpio has to be
+			  driven low so that cpsw slave 0 and phy data
+			  lines are connected via mux.
+
 
 Slave Properties:
 Required properties:
-- phy_id		: Specifies slave phy id
 - phy-mode		: See ethernet.txt file in the same directory
 
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
 - mac-address		: See ethernet.txt file in the same directory
+- phy_id		: Specifies slave phy id
+- phy-handle		: See ethernet.txt file in the same directory
+
+Slave sub-nodes:
+- fixed-link		: See fixed-link.txt file in the same directory
+			  Either the property phy_id, or the sub-node
+			  fixed-link can be specified
 
 Note: "ti,hwmods" field is used to fetch the base address and irq
 resources from TI, omap hwmod data base during device registration.
diff --git a/kernel/Documentation/devicetree/bindings/net/dsa/dsa.txt b/kernel/Documentation/devicetree/bindings/net/dsa/dsa.txt
index f0b4cd724..04e6bef3a 100644
--- a/kernel/Documentation/devicetree/bindings/net/dsa/dsa.txt
+++ b/kernel/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -44,9 +44,10 @@ Note that a port labelled "dsa" will imply checking for the uplink phandle
 described below.
 
 Optionnal property:
-- link			: Should be a phandle to another switch's DSA port.
+- link			: Should be a list of phandles to another switch's DSA port.
 			  This property is only used when switches are being
-			  chained/cascaded together.
+			  chained/cascaded together. This port is used as outgoing port
+			  towards the phandle port, which can be more than one hop away.
 
 - phy-handle		: Phandle to a PHY on an external MDIO bus, not the
 			  switch internal one. See
@@ -58,6 +59,10 @@ Optionnal property:
 			  Documentation/devicetree/bindings/net/ethernet.txt
 			  for details.
 
+- mii-bus		: Should be a phandle to a valid MDIO bus device node.
+			  This mii-bus will be used in preference to the
+			  global dsa,mii-bus defined above, for this switch.
+
 Optional subnodes:
 - fixed-link		: Fixed-link subnode describing a link to a non-MDIO
 			  managed entity. See
@@ -96,10 +101,11 @@ Example:
 				label = "cpu";
 			};
 
-			switch0uplink: port@6 {
+			switch0port6: port@6 {
 				reg = <6>;
 				label = "dsa";
-				link = <&switch1uplink>;
+				link = <&switch1port0
+				        &switch2port0>;
 			};
 		};
 
@@ -107,11 +113,31 @@ Example:
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <17 1>;	/* MDIO address 17, switch 1 in tree */
+			mii-bus = <&mii_bus1>;
+
+			switch1port0: port@0 {
+				reg = <0>;
+				label = "dsa";
+				link = <&switch0port6>;
+			};
+			switch1port1: port@1 {
+				reg = <1>;
+				label = "dsa";
+				link = <&switch2port1>;
+			};
+		};
+
+		switch@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <18 2>;	/* MDIO address 18, switch 2 in tree */
+			mii-bus = <&mii_bus1>;
 
-			switch1uplink: port@0 {
+			switch2port0: port@0 {
 				reg = <0>;
 				label = "dsa";
-				link = <&switch0uplink>;
+				link = <&switch1port1
+				        &switch0port6>;
 			};
 		};
 	};
diff --git a/kernel/Documentation/devicetree/bindings/net/ezchip_enet.txt b/kernel/Documentation/devicetree/bindings/net/ezchip_enet.txt
new file mode 100644
index 000000000..4e29b2b82
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/ezchip_enet.txt
@@ -0,0 +1,15 @@
+* EZchip NPS Management Ethernet port driver
+
+Required properties:
+- compatible: Should be "ezchip,nps-mgt-enet"
+- reg: Address and length of the register set for the device
+- interrupts: Should contain the ENET interrupt
+
+Examples:
+
+	ethernet@f0003000 {
+		compatible = "ezchip,nps-mgt-enet";
+		reg = <0xf0003000 0x44>;
+		interrupts = <7>;
+		mac-address = [ 00 11 22 33 44 55 ];
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/fixed-link.txt b/kernel/Documentation/devicetree/bindings/net/fixed-link.txt
index 82bf7e0f4..ec5d889fe 100644
--- a/kernel/Documentation/devicetree/bindings/net/fixed-link.txt
+++ b/kernel/Documentation/devicetree/bindings/net/fixed-link.txt
@@ -17,6 +17,8 @@ properties:
   enabled.
 * 'asym-pause' (boolean, optional), to indicate that asym_pause should
   be enabled.
+* 'link-gpios' ('gpio-list', optional), to indicate if a gpio can be read
+  to determine if the link is up.
 
 Old, deprecated 'fixed-link' binding:
 
@@ -30,7 +32,7 @@ Old, deprecated 'fixed-link' binding:
   - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for
     asymmetric pause
 
-Example:
+Examples:
 
 ethernet@0 {
 	...
@@ -40,3 +42,13 @@ ethernet@0 {
 	};
 	...
 };
+
+ethernet@1 {
+	...
+	fixed-link {
+	      speed = <1000>;
+	      pause;
+	      link-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+	};
+	...
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/kernel/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
index 1e97532a0..db74f0dc2 100644
--- a/kernel/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
+++ b/kernel/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt
@@ -57,6 +57,10 @@ Properties:
     "rgmii-id", as all other connection types are detected by hardware.
   - fsl,magic-packet : If present, indicates that the hardware supports
     waking up via magic packet.
+  - fsl,wake-on-filer : If present, indicates that the hardware supports
+    waking up by Filer General Purpose Interrupt (FGPI) asserted on the
+    Rx int line.  This is an advanced power management capability allowing
+    certain packet types (user) defined by filer rules to wake up the system.
   - bd-stash : If present, indicates that the hardware supports stashing
     buffer descriptors in the L2.
   - rx-stash-len : Denotes the number of bytes of a received buffer to stash
diff --git a/kernel/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/kernel/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
index 988fc694b..d1df8a00e 100644
--- a/kernel/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
+++ b/kernel/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
@@ -32,13 +32,13 @@ Required properties:
 
 Required properties:
 
-- compatible: should be "hisilicon,hip04-mdio".
+- compatible: should be "hisilicon,mdio".
 - Inherits from MDIO bus node binding [2]
 [2] Documentation/devicetree/bindings/net/phy.txt
 
 Example:
 	mdio {
-		compatible = "hisilicon,hip04-mdio";
+		compatible = "hisilicon,mdio";
 		reg = <0x28f1000 0x1000>;
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt
new file mode 100644
index 000000000..80411b2f0
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt
@@ -0,0 +1,49 @@
+Hisilicon DSA Fabric device controller
+
+Required properties:
+- compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2".
+  "hisilicon,hns-dsaf-v1" is for hip05.
+  "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612.
+- dsa-name: dsa fabric name who provide this interface.
+  should be "dsafX", X is the dsaf id.
+- mode: dsa fabric mode string. only support one of dsaf modes like these:
+		"2port-64vf",
+		"6port-16rss",
+		"6port-16vf".
+- interrupt-parent: the interrupt parent of this device.
+- interrupts: should contain the DSA Fabric and rcb interrupt.
+- reg: specifies base physical address(es) and size of the device registers.
+  The first region is external interface control register base and size.
+  The second region is SerDes base register and size.
+  The third region is the PPE register base and size.
+  The fourth region is dsa fabric base register and size.
+  The fifth region is cpld base register and size, it is not required if do not use cpld.
+- phy-handle: phy handle of physicl port, 0 if not any phy device. see ethernet.txt [1].
+- buf-size: rx buffer size, should be 16-1024.
+- desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096.
+
+[1] Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+
+dsa: dsa@c7000000 {
+	compatible = "hisilicon,hns-dsaf-v1";
+	dsa_name = "dsaf0";
+	mode = "6port-16rss";
+	interrupt-parent = <&mbigen_dsa>;
+	reg = <0x0 0xC0000000 0x0 0x420000
+	       0x0 0xC2000000 0x0 0x300000
+	       0x0 0xc5000000 0x0 0x890000
+	       0x0 0xc7000000 0x0 0x60000>;
+	phy-handle = <0 0 0 0 &soc0_phy4 &soc0_phy5 0 0>;
+	interrupts = <131 4>,<132 4>, <133 4>,<134 4>,
+		     <135 4>,<136 4>, <137 4>,<138 4>,
+		     <139 4>,<140 4>, <141 4>,<142 4>,
+		     <143 4>,<144 4>, <145 4>,<146 4>,
+		     <147 4>,<148 4>, <384 1>,<385 1>,
+		     <386 1>,<387 1>, <388 1>,<389 1>,
+		     <390 1>,<391 1>,
+	buf-size = <4096>;
+	desc-num = <1024>;
+	dma-coherent;
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt b/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt
new file mode 100644
index 000000000..9c23fdf25
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt
@@ -0,0 +1,22 @@
+Hisilicon MDIO bus controller
+
+Properties:
+- compatible: "hisilicon,mdio","hisilicon,hns-mdio".
+- reg: The base address of the MDIO bus controller register bank.
+- #address-cells: Must be <1>.
+- #size-cells: Must be <0>.  MDIO addresses have no size component.
+
+Typically an MDIO bus might have several children.
+
+Example:
+         mdio@803c0000 {
+                   #address-cells = <1>;
+                   #size-cells = <0>;
+                   compatible = "hisilicon,hns-mdio","hisilicon,mdio";
+                   reg = <0x0 0x803c0000 0x0 0x10000>;
+
+                   ethernet-phy@0 {
+                            ...
+                            reg = <0>;
+                   };
+         };
diff --git a/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt
new file mode 100644
index 000000000..41d19be70
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt
@@ -0,0 +1,47 @@
+Hisilicon Network Subsystem NIC controller
+
+Required properties:
+- compatible: "hisilicon,hns-nic-v1" or "hisilicon,hns-nic-v2".
+  "hisilicon,hns-nic-v1" is for hip05.
+  "hisilicon,hns-nic-v2" is for Hi1610 and Hi1612.
+- ae-name: accelerator name who provides this interface,
+  is simply a name referring to the name of name in the accelerator node.
+- port-id: is the index of port provided by DSAF (the accelerator). DSAF can
+  connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They
+  are called debug ports.
+
+  The remaining 6 PHYs are taken according to the mode of DSAF.
+
+  In NIC mode of DSAF, all 6 PHYs are taken as ethernet ports to the CPU. The
+  port-id can be 2 to 7. Here is the diagram:
+            +-----+---------------+
+            |            CPU      |
+            +-+-+-+---+-+-+-+-+-+-+
+              | |     | | | | | |
+             debug       service
+             port         port
+             (0,1)       (2-7)
+
+  In Switch mode of DSAF, all 6 PHYs are taken as physical ports connect to a
+  LAN Switch while the CPU side assume itself have one single NIC connect to
+  this switch. In this case, the port-id will be 2 only.
+            +-----+---------------+
+            |            CPU      |
+            +-+-+-+---+-+-+-+-+-+-+
+              | |   service| port(2)
+             debug   +------------+
+             port    |   switch   |
+             (0,1)   +-+-+-+-+-+-++
+                       | | | | | |
+                      external port
+
+- local-mac-address: mac addr of the ethernet interface
+
+Example:
+
+	ethernet@0{
+		compatible = "hisilicon,hns-nic-v1";
+		ae-name = "dsaf0";
+		port-id = <0>;
+		local-mac-address = [a2 14 e4 4b 56 76];
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt b/kernel/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt
new file mode 100644
index 000000000..a4ed2efb5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt
@@ -0,0 +1,20 @@
+* MRF24J40 IEEE 802.15.4 *
+
+Required properties:
+  - compatible:		should be "microchip,mrf24j40", "microchip,mrf24j40ma",
+			or "microchip,mrf24j40mc" depends on your transceiver
+			board
+  - spi-max-frequency:	maximal bus speed, should be set something under or equal
+			10000000
+  - reg:		the chipselect index
+  - interrupts:		the interrupt generated by the device.
+
+Example:
+
+	mrf24j40ma@0 {
+		compatible = "microchip,mrf24j40ma";
+		spi-max-frequency = <8500000>;
+		reg = <0>;
+		interrupts = <19 8>;
+		interrupt-parent = <&gpio3>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/ipq806x-dwmac.txt b/kernel/Documentation/devicetree/bindings/net/ipq806x-dwmac.txt
new file mode 100644
index 000000000..6d7ab4e52
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/ipq806x-dwmac.txt
@@ -0,0 +1,35 @@
+* IPQ806x DWMAC Ethernet controller
+
+The device inherits all the properties of the dwmac/stmmac devices
+described in the file net/stmmac.txt with the following changes.
+
+Required properties:
+
+- compatible: should be "qcom,ipq806x-gmac" along with "snps,dwmac"
+	      and any applicable more detailed version number
+	      described in net/stmmac.txt
+
+- qcom,nss-common: should contain a phandle to a syscon device mapping the
+		   nss-common registers.
+
+- qcom,qsgmii-csr: should contain a phandle to a syscon device mapping the
+		   qsgmii-csr registers.
+
+Example:
+
+	gmac: ethernet@37000000 {
+		device_type = "network";
+		compatible = "qcom,ipq806x-gmac";
+		reg = <0x37000000 0x200000>;
+		interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq";
+
+		qcom,nss-common = <&nss_common>;
+		qcom,qsgmii-csr = <&qsgmii_csr>;
+
+		clocks = <&gcc GMAC_CORE1_CLK>;
+		clock-names = "stmmaceth";
+
+		resets = <&gcc GMAC_CORE1_RESET>;
+		reset-names = "stmmaceth";
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/keystone-netcp.txt b/kernel/Documentation/devicetree/bindings/net/keystone-netcp.txt
index d0e6fa38f..b30ab6b5c 100644
--- a/kernel/Documentation/devicetree/bindings/net/keystone-netcp.txt
+++ b/kernel/Documentation/devicetree/bindings/net/keystone-netcp.txt
@@ -130,7 +130,11 @@ Required properties:
 
 Optional properties:
 - efuse-mac:	If this is 1, then the MAC address for the interface is
-		obtained from the device efuse mac address register
+		obtained from the device efuse mac address register.
+		If this is 2, the two DWORDs occupied by the MAC address
+		are swapped.  The netcp driver will swap the two DWORDs
+		back to the proper order when this property is set to 2
+		when it obtains the mac address from efuse.
 - local-mac-address:	the driver is designed to use the of_get_mac_address api
 			only if efuse-mac is 0. When efuse-mac is 0, the MAC
 			address is obtained from local-mac-address. If this
diff --git a/kernel/Documentation/devicetree/bindings/net/macb.txt b/kernel/Documentation/devicetree/bindings/net/macb.txt
index ba19d671e..b5d79761a 100644
--- a/kernel/Documentation/devicetree/bindings/net/macb.txt
+++ b/kernel/Documentation/devicetree/bindings/net/macb.txt
@@ -7,8 +7,10 @@ Required properties:
   Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
   Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
   the Cadence GEM, or the generic form: "cdns,gem".
-  Use "cdns,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs.
-  Use "cdns,sama5d4-gem" for the Gigabit IP available on Atmel sama5d4 SoCs.
+  Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs.
+  Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs.
+  Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs.
+  Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC.
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt
 - phy-mode: See ethernet.txt file in the same directory.
diff --git a/kernel/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/kernel/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
index f5a8ca29a..aeea50c84 100644
--- a/kernel/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
+++ b/kernel/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
@@ -8,6 +8,11 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 - clocks: a pointer to the reference clock for this device.
 
+Optional properties:
+- tx-csum-limit: maximum mtu supported by port that allow TX checksum.
+  Value is presented in bytes. If not used, by default 1600B is set for
+  "marvell,armada-370-neta" and 9800B for others.
+
 Example:
 
 ethernet@d0070000 {
@@ -15,6 +20,7 @@ ethernet@d0070000 {
 	reg = <0xd0070000 0x2500>;
 	interrupts = <8>;
 	clocks = <&gate_clk 4>;
+	tx-csum-limit = <9800>
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";
diff --git a/kernel/Documentation/devicetree/bindings/net/maxim,ds26522.txt b/kernel/Documentation/devicetree/bindings/net/maxim,ds26522.txt
new file mode 100644
index 000000000..ee8bb725f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/maxim,ds26522.txt
@@ -0,0 +1,13 @@
+* Maxim (Dallas) DS26522 Dual T1/E1/J1 Transceiver
+
+Required properties:
+- compatible: Should contain "maxim,ds26522".
+- reg: SPI CS.
+- spi-max-frequency: SPI clock.
+
+Example:
+	slic@1 {
+		compatible = "maxim,ds26522";
+		reg = <1>;
+		spi-max-frequency = <2000000>; /* input clock */
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/kernel/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt
new file mode 100644
index 000000000..76df91738
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt
@@ -0,0 +1,86 @@
+* Marvell International Ltd. NCI NFC Controller
+
+Required properties:
+- compatible: Should be:
+  - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices
+  - "marvell,nfc-i2c" for I2C devices
+  - "marvell,nfc-spi" for SPI devices
+
+Optional SoC specific properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- reset-n-io: Output GPIO pin used to reset the chip (active low).
+- hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
+
+Optional UART-based chip specific properties:
+- flow-control: Specifies that the chip is using RTS/CTS.
+- break-control: Specifies that the chip needs specific break management.
+
+Optional I2C-based chip specific properties:
+- i2c-int-falling: Specifies that the chip read event shall be trigged on
+  		   falling edge.
+- i2c-int-rising: Specifies that the chip read event shall be trigged on
+  		  rising edge.
+
+Example (for ARM-based BeagleBoard Black with 88W8887 on UART5):
+
+&uart5 {
+	status = "okay";
+
+	nfcmrvluart: nfcmrvluart@5 {
+		compatible = "marvell,nfc-uart";
+
+		reset-n-io = <&gpio3 16 0>;
+
+		hci-muxed;
+		flow-control;
+        }
+};
+
+
+Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1):
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	nfcmrvli2c0: i2c@1 {
+		compatible = "marvell,nfc-i2c";
+
+		reg = <0x8>;
+
+		/* I2C INT configuration */
+		interrupt-parent = <&gpio3>;
+		interrupts = <21 0>;
+
+		/* I2C INT trigger configuration */
+		i2c-int-rising;
+
+		/* Reset IO */
+		reset-n-io = <&gpio3 19 0>;
+	};
+};
+
+
+Example (for ARM-based BeagleBoard Black on SPI0):
+
+&spi0 {
+
+	mrvlnfcspi0: spi@0 {
+		compatible = "marvell,nfc-spi";
+
+		reg = <0>;
+
+		/* SPI Bus configuration */
+		spi-max-frequency = <3000000>;
+		spi-cpha;
+		spi-cpol;
+
+		/* SPI INT configuration */
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 0>;
+
+		/* Reset IO */
+       		reset-n-io = <&gpio3 19 0>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt b/kernel/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt
new file mode 100644
index 000000000..fb1e75fac
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt
@@ -0,0 +1,27 @@
+* Samsung S3FWRN5 NCI NFC Controller
+
+Required properties:
+- compatible: Should be "samsung,s3fwrn5-i2c".
+- reg: address on the bus
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip
+- s3fwrn5,fw-gpios: Output GPIO pin used to enter firmware mode and
+  sleep/wakeup control
+
+Example:
+
+&hsi2c_4 {
+	status = "okay";
+	s3fwrn5@27 {
+		compatible = "samsung,s3fwrn5-i2c";
+
+		reg = <0x27>;
+
+		interrupt-parent = <&gpa1>;
+		interrupts = <3 0 0>;
+
+		s3fwrn5,en-gpios = <&gpf1 4 0>;
+		s3fwrn5,fw-gpios = <&gpj0 2 0>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/kernel/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt
index bb237072d..263732e88 100644
--- a/kernel/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt
+++ b/kernel/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt
@@ -1,7 +1,7 @@
-* STMicroelectronics SAS. ST21NFCB NFC Controller
+* STMicroelectronics SAS. ST NCI NFC Controller
 
 Required properties:
-- compatible: Should be "st,st21nfcb-i2c".
+- compatible: Should be "st,st21nfcb-i2c" or "st,st21nfcc-i2c".
 - clock-frequency: I²C work frequency.
 - reg: address on the bus
 - interrupt-parent: phandle for the interrupt gpio controller
@@ -11,6 +11,10 @@ Required properties:
 Optional SoC Specific Properties:
 - pinctrl-names: Contains only one value - "default".
 - pintctrl-0: Specifies the pin control groups used for this controller.
+- ese-present: Specifies that an ese is physically connected to the nfc
+controller.
+- uicc-present: Specifies that the uicc swp signal can be physically
+connected to the nfc controller.
 
 Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2):
 
@@ -29,5 +33,8 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2):
 		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 
 		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+
+		ese-present;
+		uicc-present;
 	};
 };
diff --git a/kernel/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/kernel/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt
new file mode 100644
index 000000000..711ca85a3
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt
@@ -0,0 +1,38 @@
+* STMicroelectronics SAS. ST NCI NFC Controller
+
+Required properties:
+- compatible: Should be "st,st21nfcb-spi"
+- spi-max-frequency: Maximum SPI frequency (<= 4000000).
+- interrupt-parent: phandle for the interrupt gpio controller
+- interrupts: GPIO interrupt to which the chip is connected
+- reset-gpios: Output GPIO pin used to reset the ST21NFCB
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- ese-present: Specifies that an ese is physically connected to the nfc
+controller.
+- uicc-present: Specifies that the uicc swp signal can be physically
+connected to the nfc controller.
+
+Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4):
+
+&mcspi4 {
+
+	status = "okay";
+
+	st21nfcb: st21nfcb@0 {
+
+		compatible = "st,st21nfcb-spi";
+
+		clock-frequency = <4000000>;
+
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+
+		reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+
+		ese-present;
+		uicc-present;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/kernel/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
index 7c89ca290..32b35a07a 100644
--- a/kernel/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
+++ b/kernel/Documentation/devicetree/bindings/net/nfc/trf7970a.txt
@@ -18,6 +18,9 @@ Optional SoC Specific Properties:
   "IRQ Status Read" erratum.
 - en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF"
   erratum.
+- t5t-rmb-extra-byte-quirk: Specify that the trf7970a has the erratum
+  where an extra byte is returned by Read Multiple Block commands issued
+  to Type 5 tags.
 
 Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 
@@ -39,6 +42,7 @@ Example (for ARM-based BeagleBone with TRF7970A on SPI1):
 		autosuspend-delay = <30000>;
 		irq-status-read-quirk;
 		en2-rf-quirk;
+		t5t-rmb-extra-byte-quirk;
 		status = "okay";
 	};
 };
diff --git a/kernel/Documentation/devicetree/bindings/net/nxp,lpc1850-dwmac.txt b/kernel/Documentation/devicetree/bindings/net/nxp,lpc1850-dwmac.txt
new file mode 100644
index 000000000..7edba1264
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/nxp,lpc1850-dwmac.txt
@@ -0,0 +1,20 @@
+* NXP LPC1850 GMAC ethernet controller
+
+This device is a platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+Required properties:
+ - compatible:  Should contain "nxp,lpc1850-dwmac"
+
+Examples:
+
+mac: ethernet@40010000 {
+	compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
+	reg = <0x40010000 0x2000>;
+	interrupts = <5>;
+	interrupt-names = "macirq";
+	clocks = <&ccu1 CLK_CPU_ETHERNET>;
+	clock-names = "stmmaceth";
+	resets = <&rgu 22>;
+	reset-names = "stmmaceth";
+}
diff --git a/kernel/Documentation/devicetree/bindings/net/phy.txt b/kernel/Documentation/devicetree/bindings/net/phy.txt
index 40831fbaf..525e1658f 100644
--- a/kernel/Documentation/devicetree/bindings/net/phy.txt
+++ b/kernel/Documentation/devicetree/bindings/net/phy.txt
@@ -30,6 +30,9 @@ Optional Properties:
 
 - max-speed: Maximum PHY supported speed (10, 100, 1000...)
 
+- broken-turn-around: If set, indicates the PHY device does not correctly
+  release the turn around line low at the end of a MDIO transaction.
+
 Example:
 
 ethernet-phy@0 {
diff --git a/kernel/Documentation/devicetree/bindings/net/renesas,ravb.txt b/kernel/Documentation/devicetree/bindings/net/renesas,ravb.txt
new file mode 100644
index 000000000..b486f3f5f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/renesas,ravb.txt
@@ -0,0 +1,103 @@
+* Renesas Electronics Ethernet AVB
+
+This file provides information on what the device node for the Ethernet AVB
+interface contains.
+
+Required properties:
+- compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC.
+	      "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC.
+	      "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC.
+- reg: offset and length of (1) the register block and (2) the stream buffer.
+- interrupts: A list of interrupt-specifiers, one for each entry in
+	      interrupt-names.
+	      If interrupt-names is not present, an interrupt specifier
+	      for a single muxed interrupt.
+- phy-mode: see ethernet.txt file in the same directory.
+- phy-handle: see ethernet.txt file in the same directory.
+- #address-cells: number of address cells for the MDIO bus, must be equal to 1.
+- #size-cells: number of size cells on the MDIO bus, must be equal to 0.
+- clocks: clock phandle and specifier pair.
+- pinctrl-0: phandle, referring to a default pin configuration node.
+
+Optional properties:
+- interrupt-parent: the phandle for the interrupt controller that services
+		    interrupts for this device.
+- interrupt-names: A list of interrupt names.
+		   For the R8A7795 SoC this property is mandatory;
+		   it should include one entry per channel, named "ch%u",
+		   where %u is the channel number ranging from 0 to 24.
+		   For other SoCs this property is optional; if present
+		   it should contain "mux" for a single muxed interrupt.
+- pinctrl-names: pin configuration state name ("default").
+- renesas,no-ether-link: boolean, specify when a board does not provide a proper
+			 AVB_LINK signal.
+- renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is
+				 active-low instead of normal active-high.
+
+Example:
+
+	ethernet@e6800000 {
+		compatible = "renesas,etheravb-r8a7795";
+		reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "ch0", "ch1", "ch2", "ch3",
+				  "ch4", "ch5", "ch6", "ch7",
+				  "ch8", "ch9", "ch10", "ch11",
+				  "ch12", "ch13", "ch14", "ch15",
+				  "ch16", "ch17", "ch18", "ch19",
+				  "ch20", "ch21", "ch22", "ch23",
+				  "ch24";
+		clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>;
+		power-domains = <&cpg_clocks>;
+		phy-mode = "rgmii-id";
+		phy-handle = <&phy0>;
+
+		pinctrl-0 = <&ether_pins>;
+		pinctrl-names = "default";
+		renesas,no-ether-link;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			rxc-skew-ps = <900>;
+			rxdv-skew-ps = <0>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txc-skew-ps = <900>;
+			txen-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+			reg = <0>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/kernel/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
index 21fd199e8..93eac7ce1 100644
--- a/kernel/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
+++ b/kernel/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
@@ -3,7 +3,7 @@ Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC)
 The device node has following properties.
 
 Required properties:
- - compatible: Can be "rockchip,rk3288-gmac".
+ - compatible: Can be one of "rockchip,rk3288-gmac", "rockchip,rk3368-gmac"
  - reg: addresses and length of the register sets for the device.
  - interrupts: Should contain the GMAC interrupts.
  - interrupt-names: Should contain the interrupt names "macirq".
diff --git a/kernel/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/kernel/Documentation/devicetree/bindings/net/smsc-lan87xx.txt
new file mode 100644
index 000000000..974edd5c8
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/smsc-lan87xx.txt
@@ -0,0 +1,24 @@
+SMSC LAN87xx Ethernet PHY
+
+Some boards require special tuning values. Configure them
+through an Ethernet OF device node.
+
+Optional properties:
+
+- smsc,disable-energy-detect:
+  If set, do not enable energy detect mode for the SMSC phy.
+  default: enable energy detect mode
+
+Examples:
+smsc phy with disabled energy detect mode on an am335x based board.
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+
+	ethernetphy0: ethernet-phy@0 {
+		reg = <0>;
+		smsc,disable-energy-detect;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/kernel/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
new file mode 100644
index 000000000..51f8d2eba
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
@@ -0,0 +1,75 @@
+* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
+
+
+Required properties:
+- compatible: Should be "snps,dwc-qos-ethernet-4.10"
+- reg: Address and length of the register set for the device
+- clocks: Phandles to the reference clock and the bus clock
+- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk"
+  for the bus clock.
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the core's combined interrupt signal
+- phy-mode: See ethernet.txt file in the same directory
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent
+- mac-address: See ethernet.txt in the same directory
+- local-mac-address: See ethernet.txt in the same directory
+- snps,en-lpi: If present it enables use of the AXI low-power interface
+- snps,write-requests: Number of write requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,read-requests: Number of read requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB
+  representing 4, then 8 etc.
+- snps,txpbl: DMA Programmable burst length for the TX DMA
+- snps,rxpbl: DMA Programmable burst length for the RX DMA
+- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
+  TX low-power mode.
+- phy-handle: See ethernet.txt file in the same directory
+- mdio device tree subnode: When the GMAC has a phy connected to its local
+    mdio, there must be device tree subnode with the following
+    required properties:
+    - compatible: Must be "snps,dwc-qos-ethernet-mdio".
+    - #address-cells: Must be <1>.
+    - #size-cells: Must be <0>.
+
+    For each phy on the mdio bus, there must be a node with the following
+    fields:
+
+    - reg: phy id used to communicate to phy.
+    - device_type: Must be "ethernet-phy".
+    - fixed-mode device tree subnode: see fixed-link.txt in the same directory
+
+Examples:
+ethernet2@40010000 {
+	clock-names = "phy_ref_clk", "apb_pclk";
+	clocks = <&clkc 17>, <&clkc 15>;
+	compatible = "snps,dwc-qos-ethernet-4.10";
+	interrupt-parent = <&intc>;
+	interrupts = <0x0 0x1e 0x4>;
+	reg = <0x40010000 0x4000>;
+	phy-handle = <&phy2>;
+	phy-mode = "gmii";
+
+	snps,en-tx-lpi-clockgating;
+	snps,en-lpi;
+	snps,write-requests = <2>;
+	snps,read-requests = <16>;
+	snps,burst-map = <0x7>;
+	snps,txpbl = <8>;
+	snps,rxpbl = <2>;
+
+	dma-coherent;
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		phy2: phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			device_type = "ethernet-phy";
+			reg = <0x1>;
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/net/ti,dp83867.txt b/kernel/Documentation/devicetree/bindings/net/ti,dp83867.txt
new file mode 100644
index 000000000..58d935b58
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/ti,dp83867.txt
@@ -0,0 +1,25 @@
+* Texas Instruments - dp83867 Giga bit ethernet phy
+
+Required properties:
+	- reg - The ID number for the phy, usually a small integer
+	- ti,rx-internal-delay - RGMII Recieve Clock Delay - see dt-bindings/net/ti-dp83867.h
+		for applicable values
+	- ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
+		for applicable values
+	- ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h
+		for applicable values
+
+Default child nodes are standard Ethernet PHY device
+nodes as described in Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+
+	ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+
+Datasheet can be found:
+http://www.ti.com/product/DP83867IR/datasheet