These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 86 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/kernel/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt
new file mode 100644
index 000000000..76df91738
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt
@@ -0,0 +1,86 @@
+* Marvell International Ltd. NCI NFC Controller
+
+Required properties:
+- compatible: Should be:
+  - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices
+  - "marvell,nfc-i2c" for I2C devices
+  - "marvell,nfc-spi" for SPI devices
+
+Optional SoC specific properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+- reset-n-io: Output GPIO pin used to reset the chip (active low).
+- hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
+
+Optional UART-based chip specific properties:
+- flow-control: Specifies that the chip is using RTS/CTS.
+- break-control: Specifies that the chip needs specific break management.
+
+Optional I2C-based chip specific properties:
+- i2c-int-falling: Specifies that the chip read event shall be trigged on
+  		   falling edge.
+- i2c-int-rising: Specifies that the chip read event shall be trigged on
+  		  rising edge.
+
+Example (for ARM-based BeagleBoard Black with 88W8887 on UART5):
+
+&uart5 {
+	status = "okay";
+
+	nfcmrvluart: nfcmrvluart@5 {
+		compatible = "marvell,nfc-uart";
+
+		reset-n-io = <&gpio3 16 0>;
+
+		hci-muxed;
+		flow-control;
+        }
+};
+
+
+Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1):
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	nfcmrvli2c0: i2c@1 {
+		compatible = "marvell,nfc-i2c";
+
+		reg = <0x8>;
+
+		/* I2C INT configuration */
+		interrupt-parent = <&gpio3>;
+		interrupts = <21 0>;
+
+		/* I2C INT trigger configuration */
+		i2c-int-rising;
+
+		/* Reset IO */
+		reset-n-io = <&gpio3 19 0>;
+	};
+};
+
+
+Example (for ARM-based BeagleBoard Black on SPI0):
+
+&spi0 {
+
+	mrvlnfcspi0: spi@0 {
+		compatible = "marvell,nfc-spi";
+
+		reg = <0>;
+
+		/* SPI Bus configuration */
+		spi-max-frequency = <3000000>;
+		spi-cpha;
+		spi-cpol;
+
+		/* SPI INT configuration */
+		interrupt-parent = <&gpio1>;
+		interrupts = <17 0>;
+
+		/* Reset IO */
+       		reset-n-io = <&gpio3 19 0>;
+	};
+};