These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 0 insertions, 48 deletions

diff --git a/kernel/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/kernel/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
deleted file mode 100644
index 8db32384a..000000000
--- a/kernel/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ /dev/null
@@ -1,48 +0,0 @@
-* AMD 10GbE PHY driver (amd-xgbe-phy)
-
-Required properties:
-- compatible: Should be "amd,xgbe-phy-seattle-v1a" and
-  "ethernet-phy-ieee802.3-c45"
-- reg: Address and length of the register sets for the device
-   - SerDes Rx/Tx registers
-   - SerDes integration registers (1/2)
-   - SerDes integration registers (2/2)
-- interrupt-parent: Should be the phandle for the interrupt controller
-  that services interrupts for this device
-- interrupts: Should contain the amd-xgbe-phy interrupt.
-
-Optional properties:
-- amd,speed-set: Speed capabilities of the device
-    0 - 1GbE and 10GbE (default)
-    1 - 2.5GbE and 10GbE
-
-The following optional properties are represented by an array with each
-value corresponding to a particular speed. The first array value represents
-the setting for the 1GbE speed, the second value for the 2.5GbE speed and
-the third value for the 10GbE speed.  All three values are required if the
-property is used.
-- amd,serdes-blwc: Baseline wandering correction enablement
-    0 - Off
-    1 - On
-- amd,serdes-cdr-rate: CDR rate speed selection
-- amd,serdes-pq-skew: PQ (data sampling) skew
-- amd,serdes-tx-amp: TX amplitude boost
-- amd,serdes-dfe-tap-config: DFE taps available to run
-- amd,serdes-dfe-tap-enable: DFE taps to enable
-
-Example:
-	xgbe_phy@e1240800 {
-		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
-		reg = <0 0xe1240800 0 0x00400>,
-		      <0 0xe1250000 0 0x00060>,
-		      <0 0xe1250080 0 0x00004>;
-		interrupt-parent = <&gic>;
-		interrupts = <0 323 4>;
-		amd,speed-set = <0>;
-		amd,serdes-blwc = <1>, <1>, <0>;
-		amd,serdes-cdr-rate = <2>, <2>, <7>;
-		amd,serdes-pq-skew = <10>, <10>, <30>;
-		amd,serdes-tx-amp = <15>, <15>, <10>;
-		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
-		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
-	};