diff options
author | 2016-04-11 10:41:07 +0300 | |
---|---|---|
committer | 2016-04-13 08:17:18 +0300 | |
commit | e09b41010ba33a20a87472ee821fa407a5b8da36 (patch) | |
tree | d10dc367189862e7ca5c592f033dc3726e1df4e3 /kernel/Documentation/devicetree/bindings/mtd/vf610-nfc.txt | |
parent | f93b97fd65072de626c074dbe099a1fff05ce060 (diff) |
These changes are the raw update to linux-4.4.6-rt14. Kernel sources
are taken from kernel.org, and rt patch from the rt wiki download page.
During the rebasing, the following patch collided:
Force tick interrupt and get rid of softirq magic(I70131fb85).
Collisions have been removed because its logic was found on the
source already.
Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>
Diffstat (limited to 'kernel/Documentation/devicetree/bindings/mtd/vf610-nfc.txt')
-rw-r--r-- | kernel/Documentation/devicetree/bindings/mtd/vf610-nfc.txt | 59 |
1 files changed, 59 insertions, 0 deletions
diff --git a/kernel/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/kernel/Documentation/devicetree/bindings/mtd/vf610-nfc.txt new file mode 100644 index 000000000..c96eeb65f --- /dev/null +++ b/kernel/Documentation/devicetree/bindings/mtd/vf610-nfc.txt @@ -0,0 +1,59 @@ +Freescale's NAND flash controller (NFC) + +This variant of the Freescale NAND flash controller (NFC) can be found on +Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70. + +Required properties: +- compatible: Should be set to "fsl,vf610-nfc". +- reg: address range of the NFC. +- interrupts: interrupt of the NFC. +- #address-cells: shall be set to 1. Encode the nand CS. +- #size-cells : shall be set to 0. +- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>; +- assigned-clock-rates: The NAND bus timing is derived from this clock + rate and should not exceed maximum timing for any NAND memory chip + in a board stuffing. Typical NAND memory timings derived from this + clock are found in the SoC hardware reference manual. Furthermore, + there might be restrictions on maximum rates when using hardware ECC. + +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. + +Required children nodes: +Children nodes represent the available nand chips. Currently the driver can +only handle one NAND chip. + +Required properties: +- compatible: Should be set to "fsl,vf610-nfc-cs". +- nand-bus-width: see nand.txt +- nand-ecc-mode: see nand.txt + +Required properties for hardware ECC: +- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand.txt) +- nand-ecc-step-size: step size equals page size, currently only 2k pages are + supported +- nand-on-flash-bbt: see nand.txt + +Example: + + nfc: nand@400e0000 { + compatible = "fsl,vf610-nfc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x400e0000 0x4000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_NFC>; + clock-names = "nfc"; + assigned-clocks = <&clks VF610_CLK_NFC>; + assigned-clock-rates = <33000000>; + + nand@0 { + compatible = "fsl,vf610-nfc-nandcs"; + reg = <0>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <32>; + nand-ecc-step-size = <2048>; + nand-on-flash-bbt; + }; + }; |