These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

1 files changed, 0 insertions, 98 deletions

diff --git a/kernel/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt b/kernel/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
deleted file mode 100644
index 973c27273..000000000
--- a/kernel/Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
+++ /dev/null
@@ -1,98 +0,0 @@
-MIPI DSI (Display Serial Interface) busses
-==========================================
-
-The MIPI Display Serial Interface specifies a serial bus and a protocol for
-communication between a host and up to four peripherals. This document will
-define the syntax used to represent a DSI bus in a device tree.
-
-This document describes DSI bus-specific properties only or defines existing
-standard properties in the context of the DSI bus.
-
-Each DSI host provides a DSI bus. The DSI host controller's node contains a
-set of properties that characterize the bus. Child nodes describe individual
-peripherals on that bus.
-
-The following assumes that only a single peripheral is connected to a DSI
-host. Experience shows that this is true for the large majority of setups.
-
-DSI host
---------
-
-In addition to the standard properties and those defined by the parent bus of
-a DSI host, the following properties apply to a node representing a DSI host.
-
-Required properties:
-- #address-cells: The number of cells required to represent an address on the
-  bus. DSI peripherals are addressed using a 2-bit virtual channel number, so
-  a maximum of 4 devices can be addressed on a single bus. Hence the value of
-  this property should be 1.
-- #size-cells: Should be 0. There are cases where it makes sense to use a
-  different value here. See below.
-
-DSI peripheral
---------------
-
-Peripherals are represented as child nodes of the DSI host's node. Properties
-described here apply to all DSI peripherals, but individual bindings may want
-to define additional, device-specific properties.
-
-Required properties:
-- reg: The virtual channel number of a DSI peripheral. Must be in the range
-  from 0 to 3.
-
-Some DSI peripherals respond to more than a single virtual channel. In that
-case two alternative representations can be chosen:
-- The reg property can take multiple entries, one for each virtual channel
-  that the peripheral responds to.
-- If the virtual channels that a peripheral responds to are consecutive, the
-  #size-cells can be set to 1. The first cell of each entry in the reg
-  property is the number of the first virtual channel and the second cell is
-  the number of consecutive virtual channels.
-
-Example
--------
-
-	dsi-host {
-		...
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* peripheral responds to virtual channel 0 */
-		peripheral@0 {
-			compatible = "...";
-			reg = <0>;
-		};
-
-		...
-	};
-
-	dsi-host {
-		...
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* peripheral responds to virtual channels 0 and 2 */
-		peripheral@0 {
-			compatible = "...";
-			reg = <0, 2>;
-		};
-
-		...
-	};
-
-	dsi-host {
-		...
-
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		/* peripheral responds to virtual channels 1, 2 and 3 */
-		peripheral@1 {
-			compatible = "...";
-			reg = <1 3>;
-		};
-
-		...
-	};