Add the rt linux 4.1.3-rt3 as base

Import the rt linux 4.1.3-rt3 as OPNFV kvm base.

It's from git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git linux-4.1.y-rt and
the base is:

commit 0917f823c59692d751951bf5ea699a2d1e2f26a2
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date:   Sat Jul 25 12:13:34 2015 +0200

    Prepare v4.1.3-rt3

    Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

We lose all the git history this way and it's not good. We
should apply another opnfv project repo in future.

Change-Id: I87543d81c9df70d99c5001fbdf646b202c19f423
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>

1 files changed, 264 insertions, 0 deletions

diff --git a/kernel/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/kernel/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
new file mode 100644
index 000000000..5e97a9593
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
@@ -0,0 +1,264 @@
+Qualcomm Resource Power Manager (RPM)
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-apq8064"
+		    "qcom,rpm-msm8660"
+		    "qcom,rpm-msm8960"
+		    "qcom,rpm-ipq8064"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: base address and size of the RPM's message ram
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: three entries specifying the RPM's:
+		    1. acknowledgement interrupt
+		    2. error interrupt
+		    3. wakeup interrupt
+
+- interrupt-names:
+	Usage: required
+	Value type: <string-array>
+	Definition: must be the three strings "ack", "err" and "wakeup", in order
+
+- qcom,ipc:
+	Usage: required
+	Value type: <prop-encoded-array>
+
+	Definition: three entries specifying the outgoing ipc bit used for
+		    signaling the RPM:
+		    - phandle to a syscon node representing the apcs registers
+		    - u32 representing offset to the register within the syscon
+		    - u32 representing the ipc bit within the register
+
+
+= SUBNODES
+
+The RPM exposes resources to its subnodes. The below bindings specify the set
+of valid subnodes that can operate on these resources.
+
+== Regulators
+
+Regulator nodes are identified by their compatible:
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-pm8058-regulators"
+		    "qcom,rpm-pm8901-regulators"
+		    "qcom,rpm-pm8921-regulators"
+
+- vdd_l0_l1_lvs-supply:
+- vdd_l2_l11_l12-supply:
+- vdd_l3_l4_l5-supply:
+- vdd_l6_l7-supply:
+- vdd_l8-supply:
+- vdd_l9-supply:
+- vdd_l10-supply:
+- vdd_l13_l16-supply:
+- vdd_l14_l15-supply:
+- vdd_l17_l18-supply:
+- vdd_l19_l20-supply:
+- vdd_l21-supply:
+- vdd_l22-supply:
+- vdd_l23_l24_l25-supply:
+- vdd_ncp-supply:
+- vdd_s0-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+	Usage: optional (pm8058 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+- lvs0_in-supply:
+- lvs1_in-supply:
+- lvs2_in-supply:
+- lvs3_in-supply:
+- mvs_in-supply:
+- vdd_l0-supply:
+- vdd_l1-supply:
+- vdd_l2-supply:
+- vdd_l3-supply:
+- vdd_l4-supply:
+- vdd_l5-supply:
+- vdd_l6-supply:
+- vdd_s0-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+	Usage: optional (pm8901 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+- vdd_l1_l2_l12_l18-supply:
+- vdd_l3_l15_l17-supply:
+- vdd_l4_l14-supply:
+- vdd_l5_l8_l16-supply:
+- vdd_l6_l7-supply:
+- vdd_l9_l11-supply:
+- vdd_l10_l22-supply:
+- vdd_l21_l23_l29-supply:
+- vdd_l24-supply:
+- vdd_l25-supply:
+- vdd_l26-supply:
+- vdd_l27-supply:
+- vdd_l28-supply:
+- vdd_ncp-supply:
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+- vin_5vs-supply:
+- vin_lvs1_3_6-supply:
+- vin_lvs2-supply:
+- vin_lvs4_5_7-supply:
+	Usage: optional (pm8921 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
+The regulator node houses sub-nodes for each regulator within the device. Each
+sub-node is identified using the node's name, with valid values listed for each
+of the pmics below.
+
+pm8058:
+	l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
+	l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
+	lvs0, lvs1, ncp
+
+pm8901:
+	l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
+	mvs
+
+pm8921:
+	s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+	l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
+	l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
+	ncp
+
+The content of each sub-node is defined by the standard binding for regulators -
+see regulator.txt - with additional custom properties described below:
+
+=== Switch-mode Power Supply regulator custom properties
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <empty>
+	Definition: enable pull down of the regulator when inactive
+
+- qcom,switch-mode-frequency:
+	Usage: required
+	Value type: <u32>
+	Definition: Frequency (Hz) of the switch-mode power supply;
+		    must be one of:
+		    19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+		    2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+		    1480000, 1370000, 1280000, 1200000
+
+- qcom,force-mode:
+	Usage: optional (default if no other qcom,force-mode is specified)
+	Value type: <u32>
+	Defintion: indicates that the regulator should be forced to a
+		   particular mode, valid values are:
+		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+		   QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+		   QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
+					      select its own mode based on
+					      realtime current draw, only for:
+					      pm8921 smps and ftsmps
+
+- qcom,power-mode-hysteretic:
+	Usage: optional
+	Value type: <empty>
+	Definition: select that the power supply should operate in hysteretic
+		    mode, instead of the default pwm mode
+
+=== Low-dropout regulator custom properties
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <empty>
+	Definition: enable pull down of the regulator when inactive
+
+- qcom,force-mode:
+	Usage: optional
+	Value type: <u32>
+	Defintion: indicates that the regulator should not be forced to any
+		   particular mode, valid values are:
+		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+		   QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+		   QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
+						mode, i.e.  to act as a switch
+						and not regulate, only for:
+						pm8921 pldo, nldo and nldo1200
+
+=== Negative Charge Pump custom properties
+
+- qcom,switch-mode-frequency:
+	Usage: required
+	Value type: <u32>
+	Definition: Frequency (Hz) of the swith mode power supply;
+		    must be one of:
+		    19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+		    2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+		    1480000, 1370000, 1280000, 1200000
+
+= EXAMPLE
+
+	#include <dt-bindings/mfd/qcom-rpm.h>
+
+	rpm@108000 {
+		compatible = "qcom,rpm-msm8960";
+		reg = <0x108000 0x1000>;
+		qcom,ipc = <&apcs 0x8 2>;
+
+		interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
+		interrupt-names = "ack", "err", "wakeup";
+
+		regulators {
+			compatible = "qcom,rpm-pm8921-regulators";
+			vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+			s1 {
+				regulator-min-microvolt = <1225000>;
+				regulator-max-microvolt = <1225000>;
+
+				bias-pull-down;
+
+				qcom,switch-mode-frequency = <3200000>;
+			};
+
+			pm8921_s4: s4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				qcom,switch-mode-frequency = <1600000>;
+				bias-pull-down;
+
+				qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+			};
+		};
+	};
+