These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

10 files changed, 657 insertions, 5 deletions

diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt
new file mode 100644
index 000000000..22b77ee02
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt
@@ -0,0 +1,127 @@
+* Device tree bindings for ARM PL172/PL175/PL176 MultiPort Memory Controller
+
+Required properties:
+
+- compatible:		Must be "arm,primecell" and exactly one from
+			"arm,pl172", "arm,pl175" or "arm,pl176".
+
+- reg:			Must contains offset/length value for controller.
+
+- #address-cells:	Must be 2. The partition number has to be encoded in the
+			first address cell and it may accept values 0..N-1
+			(N - total number of partitions). The second cell is the
+			offset into the partition.
+
+- #size-cells:		Must be set to 1.
+
+- ranges:		Must contain one or more chip select memory regions.
+
+- clocks:		Must contain references to controller clocks.
+
+- clock-names:		Must contain "mpmcclk" and "apb_pclk".
+
+- clock-ranges:		Empty property indicating that child nodes can inherit
+			named clocks. Required only if clock tree data present
+			in device tree.
+			See clock-bindings.txt
+
+Child chip-select (cs) nodes contain the memory devices nodes connected to
+such as NOR (e.g. cfi-flash) and NAND.
+
+Required child cs node properties:
+
+- #address-cells:	Must be 2.
+
+- #size-cells:		Must be 1.
+
+- ranges:		Empty property indicating that child nodes can inherit
+			memory layout.
+
+- clock-ranges:		Empty property indicating that child nodes can inherit
+			named clocks. Required only if clock tree data present
+			in device tree.
+
+- mpmc,cs:		Chip select number. Indicates to the pl0172 driver
+			which chipselect is used for accessing the memory.
+
+- mpmc,memory-width:	Width of the chip select memory. Must be equal to
+			either 8, 16 or 32.
+
+Optional child cs node config properties:
+
+- mpmc,async-page-mode:	Enable asynchronous page mode.
+
+- mpmc,cs-active-high:	Set chip select polarity to active high.
+
+- mpmc,byte-lane-low:	Set byte lane state to low.
+
+- mpmc,extended-wait:	Enable extended wait.
+
+- mpmc,buffer-enable:	Enable write buffer, option is not supported by
+			PL175 and PL176 controllers.
+
+- mpmc,write-protect:	Enable write protect.
+
+Optional child cs node timing properties:
+
+- mpmc,write-enable-delay:	Delay from chip select assertion to write
+				enable (WE signal) in nano seconds.
+
+- mpmc,output-enable-delay:	Delay from chip select assertion to output
+				enable (OE signal) in nano seconds.
+
+- mpmc,write-access-delay:	Delay from chip select assertion to write
+				access in nano seconds.
+
+- mpmc,read-access-delay:	Delay from chip select assertion to read
+				access in nano seconds.
+
+- mpmc,page-mode-read-delay:	Delay for asynchronous page mode sequential
+				accesses in nano seconds.
+
+- mpmc,turn-round-delay:	Delay between access to memory banks in nano
+				seconds.
+
+If any of the above timing parameters are absent, current parameter value will
+be taken from the corresponding HW reg.
+
+Example for pl172 with nor flash on chip select 0 shown below.
+
+emc: memory-controller@40005000 {
+	compatible = "arm,pl172", "arm,primecell";
+	reg = <0x40005000 0x1000>;
+	clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>;
+	clock-names = "mpmcclk", "apb_pclk";
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x1c000000 0x1000000
+		  1 0 0x1d000000 0x1000000
+		  2 0 0x1e000000 0x1000000
+		  3 0 0x1f000000 0x1000000>;
+
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		mpmc,cs = <0>;
+		mpmc,memory-width = <16>;
+		mpmc,byte-lane-low;
+		mpmc,write-enable-delay = <0>;
+		mpmc,output-enable-delay = <0>;
+		mpmc,read-enable-delay = <70>;
+		mpmc,page-mode-read-delay = <70>;
+
+		flash@0,0 {
+			compatible = "sst,sst39vf320", "cfi-flash";
+			reg = <0 0 0x400000>;
+			bank-width = <2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "data";
+				reg = <0 0x400000>;
+			};
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt
new file mode 100644
index 000000000..efe35a065
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt
@@ -0,0 +1,35 @@
+Binding for Qualcomm  Atheros AR7xxx/AR9xxx DDR controller
+
+The DDR controller of the ARxxx and AR9xxx families provides an interface
+to flush the FIFO between various devices and the DDR. This is mainly used
+by the IRQ controller to flush the FIFO before running the interrupt handler
+of such devices.
+
+Required properties:
+
+- compatible: has to be "qca,<soc-type>-ddr-controller",
+  "qca,[ar7100|ar7240]-ddr-controller" as fallback.
+  On SoC with PCI support "qca,ar7100-ddr-controller" should be used as
+  fallback, otherwise "qca,ar7240-ddr-controller" should be used.
+- reg: Base address and size of the controllers memory area
+- #qca,ddr-wb-channel-cells: has to be 1, the index of the write buffer
+  channel
+
+Example:
+
+	ddr_ctrl: memory-controller@18000000 {
+		compatible = "qca,ar9132-ddr-controller",
+				"qca,ar7240-ddr-controller";
+		reg = <0x18000000 0x100>;
+
+		#qca,ddr-wb-channel-cells = <1>;
+	};
+
+	...
+
+	interrupt-controller {
+		...
+		qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
+		qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
+					<&ddr_ctrl 0>, <&ddr_ctrl 1>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt
new file mode 100644
index 000000000..049675944
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/calxeda-ddr-ctrlr.txt
@@ -0,0 +1,16 @@
+Calxeda DDR memory controller
+
+Properties:
+- compatible : Should be:
+  - "calxeda,hb-ddr-ctrl" for ECX-1000
+  - "calxeda,ecx-2000-ddr-ctrl" for ECX-2000
+- reg : Address and size for DDR controller registers.
+- interrupts : Interrupt for DDR controller.
+
+Example:
+
+	memory-controller@fff00000 {
+		compatible = "calxeda,hb-ddr-ctrl";
+		reg = <0xfff00000 0x1000>;
+		interrupts = <0 91 4>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
index d5e370450..89427b018 100644
--- a/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt
@@ -18,6 +18,8 @@ Properties:
               interrupt (NAND_EVTER_STAT).  If there is only one,
               that interrupt reports both types of event.
 
+- little-endian : If this property is absent, the big-endian mode will
+                  be in use as default for registers.
 
 - ranges : Each range corresponds to a single chipselect, and covers
            the entire access window as configured.
@@ -34,6 +36,7 @@ Example:
 		#size-cells = <1>;
 		reg = <0x0 0xffe1e000 0 0x2000>;
 		interrupts = <16 2 19 2>;
+		little-endian;
 
 		/* NOR, NAND Flashes and CPLD on board */
 		ranges = <0x0 0x0 0x0 0xee000000 0x02000000
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
index f3db93c85..3338a2834 100644
--- a/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt
@@ -1,6 +1,9 @@
 NVIDIA Tegra Memory Controller device tree bindings
 ===================================================
 
+memory-controller node
+----------------------
+
 Required properties:
 - compatible: Should be "nvidia,tegra<chip>-mc"
 - reg: Physical base address and length of the controller's registers.
@@ -15,9 +18,49 @@ Required properties:
 This device implements an IOMMU that complies with the generic IOMMU binding.
 See ../iommu/iommu.txt for details.
 
-Example:
---------
+emc-timings subnode
+-------------------
+
+The node should contain a "emc-timings" subnode for each supported RAM type (see field RAM_CODE in
+register PMC_STRAPPING_OPT_A).
+
+Required properties for "emc-timings" nodes :
+- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is used for.
+
+timing subnode
+--------------
+
+Each "emc-timings" node should contain a subnode for every supported EMC clock rate.
+
+Required properties for timing nodes :
+- clock-frequency : Should contain the memory clock rate in Hz.
+- nvidia,emem-configuration : Values to be written to the EMEM register block. For the Tegra124 SoC
+(see section "15.6.1 MC Registers" in the TRM), these are the registers whose values need to be
+specified, according to the board documentation:
+
+	MC_EMEM_ARB_CFG
+	MC_EMEM_ARB_OUTSTANDING_REQ
+	MC_EMEM_ARB_TIMING_RCD
+	MC_EMEM_ARB_TIMING_RP
+	MC_EMEM_ARB_TIMING_RC
+	MC_EMEM_ARB_TIMING_RAS
+	MC_EMEM_ARB_TIMING_FAW
+	MC_EMEM_ARB_TIMING_RRD
+	MC_EMEM_ARB_TIMING_RAP2PRE
+	MC_EMEM_ARB_TIMING_WAP2PRE
+	MC_EMEM_ARB_TIMING_R2R
+	MC_EMEM_ARB_TIMING_W2W
+	MC_EMEM_ARB_TIMING_R2W
+	MC_EMEM_ARB_TIMING_W2R
+	MC_EMEM_ARB_DA_TURNS
+	MC_EMEM_ARB_DA_COVERS
+	MC_EMEM_ARB_MISC0
+	MC_EMEM_ARB_MISC1
+	MC_EMEM_ARB_RING1_THROTTLE
 
+Example SoC include file:
+
+/ {
 	mc: memory-controller@0,70019000 {
 		compatible = "nvidia,tegra124-mc";
 		reg = <0x0 0x70019000 0x0 0x1000>;
@@ -34,3 +77,40 @@ Example:
 		...
 		iommus = <&mc TEGRA_SWGROUP_SDMMC1A>;
 	};
+};
+
+Example board file:
+
+/ {
+	memory-controller@0,70019000 {
+		emc-timings-3 {
+			nvidia,ram-code = <3>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/renesas,h8300-bsc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/renesas,h8300-bsc.txt
new file mode 100644
index 000000000..cdf406c90
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/renesas,h8300-bsc.txt
@@ -0,0 +1,12 @@
+* H8/300 bus controller
+
+Required properties:
+  - compatible: Must be "renesas,h8300-bsc".
+  - reg: Base address and length of BSC registers.
+
+Example.
+	bsc: memory-controller@fee01e {
+		compatible = "renesas,h8300h-bsc", "renesas,h8300-bsc";
+		reg = <0xfee01e 8>;
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt
index c64b7925c..9f78e6c82 100644
--- a/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/renesas-memory-controllers.txt
@@ -24,9 +24,9 @@ Required properties:
 Optional properties:
   - interrupts: Must contain a list of interrupt specifiers for memory
 		controller interrupts, if available.
-  - interrupts-names: Must contain a list of interrupt names corresponding to
-		      the interrupts in the interrupts property, if available.
-		      Valid interrupt names are:
+  - interrupt-names: Must contain a list of interrupt names corresponding to
+		     the interrupts in the interrupts property, if available.
+		     Valid interrupt names are:
 			- "sec" (secure interrupt)
 			- "temp" (normal (temperature) interrupt)
   - power-domains: Must contain a reference to the PM domain that the memory
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt
index f9c645414..a43d26d41 100644
--- a/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/synopsys.txt
@@ -1,5 +1,9 @@
 Binding for Synopsys IntelliDDR Multi Protocol Memory Controller
 
+This controller has an optional ECC support in half-bus width (16-bit)
+configuration. The ECC controller corrects one bit error and detects
+two bit errors.
+
 Required properties:
  - compatible: Should be 'xlnx,zynq-ddrc-a05'
  - reg: Base address and size of the controllers memory area
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt
new file mode 100644
index 000000000..b59c625d6
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt
@@ -0,0 +1,374 @@
+NVIDIA Tegra124 SoC EMC (external memory controller)
+====================================================
+
+Required properties :
+- compatible : Should be "nvidia,tegra124-emc".
+- reg : physical base address and length of the controller's registers.
+- nvidia,memory-controller : phandle of the MC driver.
+
+The node should contain a "emc-timings" subnode for each supported RAM type
+(see field RAM_CODE in register PMC_STRAPPING_OPT_A), with its unit address
+being its RAM_CODE.
+
+Required properties for "emc-timings" nodes :
+- nvidia,ram-code : Should contain the value of RAM_CODE this timing set is
+used for.
+
+Each "emc-timings" node should contain a "timing" subnode for every supported
+EMC clock rate. The "timing" subnodes should have the clock rate in Hz as
+their unit address.
+
+Required properties for "timing" nodes :
+- clock-frequency : Should contain the memory clock rate in Hz.
+- The following properties contain EMC timing characterization values
+(specified in the board documentation) :
+  - nvidia,emc-auto-cal-config : EMC_AUTO_CAL_CONFIG
+  - nvidia,emc-auto-cal-config2 : EMC_AUTO_CAL_CONFIG2
+  - nvidia,emc-auto-cal-config3 : EMC_AUTO_CAL_CONFIG3
+  - nvidia,emc-auto-cal-interval : EMC_AUTO_CAL_INTERVAL
+  - nvidia,emc-bgbias-ctl0 : EMC_BGBIAS_CTL0
+  - nvidia,emc-cfg : EMC_CFG
+  - nvidia,emc-cfg-2 : EMC_CFG_2
+  - nvidia,emc-ctt-term-ctrl : EMC_CTT_TERM_CTRL
+  - nvidia,emc-mode-1 : Mode Register 1
+  - nvidia,emc-mode-2 : Mode Register 2
+  - nvidia,emc-mode-4 : Mode Register 4
+  - nvidia,emc-mode-reset : Mode Register 0
+  - nvidia,emc-mrs-wait-cnt : EMC_MRS_WAIT_CNT
+  - nvidia,emc-sel-dpd-ctrl : EMC_SEL_DPD_CTRL
+  - nvidia,emc-xm2dqspadctrl2 : EMC_XM2DQSPADCTRL2
+  - nvidia,emc-zcal-cnt-long : EMC_ZCAL_WAIT_CNT after clock change
+  - nvidia,emc-zcal-interval : EMC_ZCAL_INTERVAL
+- nvidia,emc-configuration : EMC timing characterization data. These are the
+registers (see section "15.6.2 EMC Registers" in the TRM) whose values need to
+be specified, according to the board documentation:
+
+	EMC_RC
+	EMC_RFC
+	EMC_RFC_SLR
+	EMC_RAS
+	EMC_RP
+	EMC_R2W
+	EMC_W2R
+	EMC_R2P
+	EMC_W2P
+	EMC_RD_RCD
+	EMC_WR_RCD
+	EMC_RRD
+	EMC_REXT
+	EMC_WEXT
+	EMC_WDV
+	EMC_WDV_MASK
+	EMC_QUSE
+	EMC_QUSE_WIDTH
+	EMC_IBDLY
+	EMC_EINPUT
+	EMC_EINPUT_DURATION
+	EMC_PUTERM_EXTRA
+	EMC_PUTERM_WIDTH
+	EMC_PUTERM_ADJ
+	EMC_CDB_CNTL_1
+	EMC_CDB_CNTL_2
+	EMC_CDB_CNTL_3
+	EMC_QRST
+	EMC_QSAFE
+	EMC_RDV
+	EMC_RDV_MASK
+	EMC_REFRESH
+	EMC_BURST_REFRESH_NUM
+	EMC_PRE_REFRESH_REQ_CNT
+	EMC_PDEX2WR
+	EMC_PDEX2RD
+	EMC_PCHG2PDEN
+	EMC_ACT2PDEN
+	EMC_AR2PDEN
+	EMC_RW2PDEN
+	EMC_TXSR
+	EMC_TXSRDLL
+	EMC_TCKE
+	EMC_TCKESR
+	EMC_TPD
+	EMC_TFAW
+	EMC_TRPAB
+	EMC_TCLKSTABLE
+	EMC_TCLKSTOP
+	EMC_TREFBW
+	EMC_FBIO_CFG6
+	EMC_ODT_WRITE
+	EMC_ODT_READ
+	EMC_FBIO_CFG5
+	EMC_CFG_DIG_DLL
+	EMC_CFG_DIG_DLL_PERIOD
+	EMC_DLL_XFORM_DQS0
+	EMC_DLL_XFORM_DQS1
+	EMC_DLL_XFORM_DQS2
+	EMC_DLL_XFORM_DQS3
+	EMC_DLL_XFORM_DQS4
+	EMC_DLL_XFORM_DQS5
+	EMC_DLL_XFORM_DQS6
+	EMC_DLL_XFORM_DQS7
+	EMC_DLL_XFORM_DQS8
+	EMC_DLL_XFORM_DQS9
+	EMC_DLL_XFORM_DQS10
+	EMC_DLL_XFORM_DQS11
+	EMC_DLL_XFORM_DQS12
+	EMC_DLL_XFORM_DQS13
+	EMC_DLL_XFORM_DQS14
+	EMC_DLL_XFORM_DQS15
+	EMC_DLL_XFORM_QUSE0
+	EMC_DLL_XFORM_QUSE1
+	EMC_DLL_XFORM_QUSE2
+	EMC_DLL_XFORM_QUSE3
+	EMC_DLL_XFORM_QUSE4
+	EMC_DLL_XFORM_QUSE5
+	EMC_DLL_XFORM_QUSE6
+	EMC_DLL_XFORM_QUSE7
+	EMC_DLL_XFORM_ADDR0
+	EMC_DLL_XFORM_ADDR1
+	EMC_DLL_XFORM_ADDR2
+	EMC_DLL_XFORM_ADDR3
+	EMC_DLL_XFORM_ADDR4
+	EMC_DLL_XFORM_ADDR5
+	EMC_DLL_XFORM_QUSE8
+	EMC_DLL_XFORM_QUSE9
+	EMC_DLL_XFORM_QUSE10
+	EMC_DLL_XFORM_QUSE11
+	EMC_DLL_XFORM_QUSE12
+	EMC_DLL_XFORM_QUSE13
+	EMC_DLL_XFORM_QUSE14
+	EMC_DLL_XFORM_QUSE15
+	EMC_DLI_TRIM_TXDQS0
+	EMC_DLI_TRIM_TXDQS1
+	EMC_DLI_TRIM_TXDQS2
+	EMC_DLI_TRIM_TXDQS3
+	EMC_DLI_TRIM_TXDQS4
+	EMC_DLI_TRIM_TXDQS5
+	EMC_DLI_TRIM_TXDQS6
+	EMC_DLI_TRIM_TXDQS7
+	EMC_DLI_TRIM_TXDQS8
+	EMC_DLI_TRIM_TXDQS9
+	EMC_DLI_TRIM_TXDQS10
+	EMC_DLI_TRIM_TXDQS11
+	EMC_DLI_TRIM_TXDQS12
+	EMC_DLI_TRIM_TXDQS13
+	EMC_DLI_TRIM_TXDQS14
+	EMC_DLI_TRIM_TXDQS15
+	EMC_DLL_XFORM_DQ0
+	EMC_DLL_XFORM_DQ1
+	EMC_DLL_XFORM_DQ2
+	EMC_DLL_XFORM_DQ3
+	EMC_DLL_XFORM_DQ4
+	EMC_DLL_XFORM_DQ5
+	EMC_DLL_XFORM_DQ6
+	EMC_DLL_XFORM_DQ7
+	EMC_XM2CMDPADCTRL
+	EMC_XM2CMDPADCTRL4
+	EMC_XM2CMDPADCTRL5
+	EMC_XM2DQPADCTRL2
+	EMC_XM2DQPADCTRL3
+	EMC_XM2CLKPADCTRL
+	EMC_XM2CLKPADCTRL2
+	EMC_XM2COMPPADCTRL
+	EMC_XM2VTTGENPADCTRL
+	EMC_XM2VTTGENPADCTRL2
+	EMC_XM2VTTGENPADCTRL3
+	EMC_XM2DQSPADCTRL3
+	EMC_XM2DQSPADCTRL4
+	EMC_XM2DQSPADCTRL5
+	EMC_XM2DQSPADCTRL6
+	EMC_DSR_VTTGEN_DRV
+	EMC_TXDSRVTTGEN
+	EMC_FBIO_SPARE
+	EMC_ZCAL_WAIT_CNT
+	EMC_MRS_WAIT_CNT2
+	EMC_CTT
+	EMC_CTT_DURATION
+	EMC_CFG_PIPE
+	EMC_DYN_SELF_REF_CONTROL
+	EMC_QPOP
+
+Example SoC include file:
+
+/ {
+	emc@0,7001b000 {
+		compatible = "nvidia,tegra124-emc";
+		reg = <0x0 0x7001b000 0x0 0x1000>;
+
+		nvidia,memory-controller = <&mc>;
+	};
+};
+
+Example board file:
+
+/ {
+	emc@0,7001b000 {
+		emc-timings-3 {
+			nvidia,ram-code = <3>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emc-zcal-cnt-long = <0x00000042>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-ctt-term-ctrl = <0x00000802>;
+				nvidia,emc-cfg = <0x73240000>;
+				nvidia,emc-cfg-2 = <0x000008c5>;
+				nvidia,emc-sel-dpd-ctrl = <0x00040128>;
+				nvidia,emc-bgbias-ctl0 = <0x00000008>;
+				nvidia,emc-auto-cal-config = <0xa1430000>;
+				nvidia,emc-auto-cal-config2 = <0x00000000>;
+				nvidia,emc-auto-cal-config3 = <0x00000000>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-4 = <0x00000000>;
+
+				nvidia,emc-configuration = <
+					0x00000000 /* EMC_RC */
+					0x00000003 /* EMC_RFC */
+					0x00000000 /* EMC_RFC_SLR */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000004 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000003 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000003 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000006 /* EMC_WDV */
+					0x00000006 /* EMC_WDV_MASK */
+					0x00000006 /* EMC_QUSE */
+					0x00000002 /* EMC_QUSE_WIDTH */
+					0x00000000 /* EMC_IBDLY */
+					0x00000005 /* EMC_EINPUT */
+					0x00000005 /* EMC_EINPUT_DURATION */
+					0x00010000 /* EMC_PUTERM_EXTRA */
+					0x00000003 /* EMC_PUTERM_WIDTH */
+					0x00000000 /* EMC_PUTERM_ADJ */
+					0x00000000 /* EMC_CDB_CNTL_1 */
+					0x00000000 /* EMC_CDB_CNTL_2 */
+					0x00000000 /* EMC_CDB_CNTL_3 */
+					0x00000004 /* EMC_QRST */
+					0x0000000c /* EMC_QSAFE */
+					0x0000000d /* EMC_RDV */
+					0x0000000f /* EMC_RDV_MASK */
+					0x00000060 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000018 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000005 /* EMC_TXSR */
+					0x00000005 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TCKESR */
+					0x00000004 /* EMC_TPD */
+					0x00000000 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000005 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000064 /* EMC_TREFBW */
+					0x00000000 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x106aa298 /* EMC_FBIO_CFG5 */
+					0x002c00a0 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00064000 /* EMC_DLL_XFORM_DQS0 */
+					0x00064000 /* EMC_DLL_XFORM_DQS1 */
+					0x00064000 /* EMC_DLL_XFORM_DQS2 */
+					0x00064000 /* EMC_DLL_XFORM_DQS3 */
+					0x00064000 /* EMC_DLL_XFORM_DQS4 */
+					0x00064000 /* EMC_DLL_XFORM_DQS5 */
+					0x00064000 /* EMC_DLL_XFORM_DQS6 */
+					0x00064000 /* EMC_DLL_XFORM_DQS7 */
+					0x00064000 /* EMC_DLL_XFORM_DQS8 */
+					0x00064000 /* EMC_DLL_XFORM_DQS9 */
+					0x00064000 /* EMC_DLL_XFORM_DQS10 */
+					0x00064000 /* EMC_DLL_XFORM_DQS11 */
+					0x00064000 /* EMC_DLL_XFORM_DQS12 */
+					0x00064000 /* EMC_DLL_XFORM_DQS13 */
+					0x00064000 /* EMC_DLL_XFORM_DQS14 */
+					0x00064000 /* EMC_DLL_XFORM_DQS15 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLL_XFORM_ADDR0 */
+					0x00000000 /* EMC_DLL_XFORM_ADDR1 */
+					0x00000000 /* EMC_DLL_XFORM_ADDR2 */
+					0x00000000 /* EMC_DLL_XFORM_ADDR3 */
+					0x00000000 /* EMC_DLL_XFORM_ADDR4 */
+					0x00000000 /* EMC_DLL_XFORM_ADDR5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE8 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE9 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE10 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE11 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE12 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE13 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE14 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE15 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS8 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS9 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS10 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS11 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS12 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS13 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS14 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS15 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x0000fc00 /* EMC_DLL_XFORM_DQ4 */
+					0x0000fc00 /* EMC_DLL_XFORM_DQ5 */
+					0x0000fc00 /* EMC_DLL_XFORM_DQ6 */
+					0x0000fc00 /* EMC_DLL_XFORM_DQ7 */
+					0x10000280 /* EMC_XM2CMDPADCTRL */
+					0x00000000 /* EMC_XM2CMDPADCTRL4 */
+					0x00111111 /* EMC_XM2CMDPADCTRL5 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL3 */
+					0x77ffc081 /* EMC_XM2CLKPADCTRL */
+					0x00000e0e /* EMC_XM2CLKPADCTRL2 */
+					0x81f1f108 /* EMC_XM2COMPPADCTRL */
+					0x07070004 /* EMC_XM2VTTGENPADCTRL */
+					0x0000003f /* EMC_XM2VTTGENPADCTRL2 */
+					0x016eeeee /* EMC_XM2VTTGENPADCTRL3 */
+					0x51451400 /* EMC_XM2DQSPADCTRL3 */
+					0x00514514 /* EMC_XM2DQSPADCTRL4 */
+					0x00514514 /* EMC_XM2DQSPADCTRL5 */
+					0x51451400 /* EMC_XM2DQSPADCTRL6 */
+					0x0000003f /* EMC_DSR_VTTGEN_DRV */
+					0x00000007 /* EMC_TXDSRVTTGEN */
+					0x00000000 /* EMC_FBIO_SPARE */
+					0x00000042 /* EMC_ZCAL_WAIT_CNT */
+					0x000e000e /* EMC_MRS_WAIT_CNT2 */
+					0x00000000 /* EMC_CTT */
+					0x00000003 /* EMC_CTT_DURATION */
+					0x0000f2f3 /* EMC_CFG_PIPE */
+					0x800001c5 /* EMC_DYN_SELF_REF_CONTROL */
+					0x0000000a /* EMC_QPOP */
+				>;
+			};
+		};
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
index 938f8e1ba..0db60470e 100644
--- a/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
+++ b/kernel/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
@@ -8,6 +8,7 @@ of the EMIF IP and memory parts attached to it.
 Required properties:
 - compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
   is the IP revision of the specific EMIF instance.
+		  For am437x should be ti,emif-am4372.
 
 - phy-type	: <u32> indicating the DDR phy type. Following are the
   allowed values