These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

7 files changed, 245 insertions, 9 deletions

diff --git a/kernel/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/kernel/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt
index 4ef45636e..38941db23 100644
--- a/kernel/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt
+++ b/kernel/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt
@@ -4,7 +4,8 @@ Required properties:
 
 - compatible	: should be one of:
 		  "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg",
-		  "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg";
+		  "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg",
+		  "samsung,exynos5433-jpeg";
 - reg		: address and length of the JPEG codec IP register set;
 - interrupts	: specifies the JPEG codec IP interrupt;
 - clock-names   : should contain:
diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/adp1653.txt b/kernel/Documentation/devicetree/bindings/media/i2c/adp1653.txt
new file mode 100644
index 000000000..5ce66f210
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/media/i2c/adp1653.txt
@@ -0,0 +1,37 @@
+* Analog Devices ADP1653 flash LED driver
+
+Required Properties:
+
+  - compatible: Must contain "adi,adp1653"
+
+  - reg: I2C slave address
+
+  - enable-gpios: Specifier of the GPIO connected to EN pin
+
+There are two LED outputs available - flash and indicator. One LED is
+represented by one child node, nodes need to be named "flash" and "indicator".
+
+Required properties of the LED child node:
+- max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Required properties of the flash LED child node:
+
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+	adp1653: led-controller@30 {
+		compatible = "adi,adp1653";
+		reg = <0x30>;
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
+
+		flash {
+			flash-timeout-us = <500000>;
+			flash-max-microamp = <320000>;
+			max-microamp = <50000>;
+		};
+		indicator {
+			max-microamp = <17500>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt
index c27cede3b..8337f75c7 100644
--- a/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt
+++ b/kernel/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -1,15 +1,17 @@
-* Analog Devices ADV7604/11 video decoder with HDMI receiver
+* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
 
-The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI
-receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input,
-and the ADV7611 has one HDMI input and no analog input.
+The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+similar to the 7611 but has 2 HDMI inputs.
 
-These device tree bindings support the ADV7611 only at the moment.
+These device tree bindings support the ADV7611/12 only at the moment.
 
 Required Properties:
 
   - compatible: Must contain one of the following
     - "adi,adv7611" for the ADV7611
+    - "adi,adv7612" for the ADV7612
 
   - reg: I2C slave address
 
@@ -22,10 +24,10 @@ port, in accordance with the video interface bindings defined in
 Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
 are numbered as follows.
 
-  Port			ADV7611
+  Port			ADV7611    ADV7612
 ------------------------------------------------------------
-  HDMI			0
-  Digital output	1
+  HDMI			0             0, 1
+  Digital output	1                2
 
 The digital output port node must contain at least one endpoint.
 
@@ -45,6 +47,7 @@ Optional Endpoint Properties:
   If none of hsync-active, vsync-active and pclk-sample is specified the
   endpoint will use embedded BT.656 synchronization.
 
+  - default-input: Select which input is selected after reset.
 
 Example:
 
@@ -58,6 +61,8 @@ Example:
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		default-input = <0>;
+
 		port@0 {
 			reg = <0>;
 		};
diff --git a/kernel/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/kernel/Documentation/devicetree/bindings/media/i2c/tc358743.txt
new file mode 100644
index 000000000..521892162
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/media/i2c/tc358743.txt
@@ -0,0 +1,48 @@
+* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge
+
+The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts
+a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C.
+
+Required Properties:
+
+- compatible: value should be "toshiba,tc358743"
+- clocks, clock-names: should contain a phandle link to the reference clock
+		       source, the clock input is named "refclk".
+
+Optional Properties:
+
+- reset-gpios: gpio phandle GPIO connected to the reset pin
+- interrupts, interrupt-parent: GPIO connected to the interrupt pin
+- data-lanes: should be <1 2 3 4> for four-lane operation,
+	      or <1 2> for two-lane operation
+- clock-lanes: should be <0>
+- clock-noncontinuous: Presence of this boolean property decides whether the
+		       MIPI CSI-2 clock is continuous or non-continuous.
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+		    expressed as a 64-bit big-endian integer. The frequency
+		    is half of the bps per lane due to DDR transmission.
+
+For further information on the MIPI CSI-2 endpoint node properties, see
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	tc358743@0f {
+		compatible = "toshiba,tc358743";
+		reg = <0x0f>;
+		clocks = <&hdmi_osc>;
+		clock-names = "refclk";
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		port {
+			tc358743_out: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				data-lanes = <1 2 3 4>;
+				clock-lanes = <0>;
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <297000000>;
+			};
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/media/renesas,jpu.txt b/kernel/Documentation/devicetree/bindings/media/renesas,jpu.txt
new file mode 100644
index 000000000..0cb94201b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/media/renesas,jpu.txt
@@ -0,0 +1,24 @@
+* Renesas JPEG Processing Unit
+
+The JPEG processing unit (JPU) incorporates the JPEG codec with an encoding
+and decoding function conforming to the JPEG baseline process, so that the JPU
+can encode image data and decode JPEG data quickly.
+
+Required properties:
+  - compatible: should containg one of the following:
+			- "renesas,jpu-r8a7790" for R-Car H2
+			- "renesas,jpu-r8a7791" for R-Car M2-W
+			- "renesas,jpu-r8a7792" for R-Car V2H
+			- "renesas,jpu-r8a7793" for R-Car M2-N
+
+  - reg: Base address and length of the registers block for the JPU.
+  - interrupts: JPU interrupt specifier.
+  - clocks: A phandle + clock-specifier pair for the JPU functional clock.
+
+Example: R8A7790 (R-Car H2) JPU node
+	jpeg-codec@fe980000 {
+		compatible = "renesas,jpu-r8a7790";
+		reg = <0 0xfe980000 0 0x10300>;
+		interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7790_CLK_JPU>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/media/st,stih4xx.txt b/kernel/Documentation/devicetree/bindings/media/st,stih4xx.txt
new file mode 100644
index 000000000..df655cd3a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/media/st,stih4xx.txt
@@ -0,0 +1,32 @@
+STMicroelectronics stih4xx platforms
+
+bdisp: 2D blitter for STMicroelectronics SoC.
+
+Required properties:
+- compatible: should be "st,stih407-bdisp".
+- reg: BDISP physical address location and length.
+- interrupts: BDISP interrupt number.
+- clocks: from common clock binding: handle hardware IP needed clocks, the
+  number of clocks may depend on the SoC type.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: names of the clocks listed in clocks property in the same order.
+
+Example:
+
+	bdisp0:bdisp@9f10000 {
+		compatible = "st,stih407-bdisp";
+		reg = <0x9f10000 0x1000>;
+		interrupts = <GIC_SPI 38 IRQ_TYPE_NONE>;
+		clock-names = "bdisp";
+		clocks = <&clk_s_c0_flexgen CLK_IC_BDISP_0>;
+	};
+
+Aliases:
+Each BDISP should have a numbered alias in the aliases node, in the form of
+bdispN, N = 0 or 1.
+
+Example:
+
+	aliases {
+		bdisp0 = &bdisp0;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/kernel/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
new file mode 100644
index 000000000..d4def767b
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
@@ -0,0 +1,89 @@
+STMicroelectronics STi c8sectpfe binding
+============================================
+
+This document describes the c8sectpfe device bindings that is used to get transport
+stream data into the SoC on the TS pins, and into DDR for further processing.
+
+It is typically used in conjunction with one or more demodulator and tuner devices
+which converts from the RF to digital domain. Demodulators and tuners are usually
+located on an external DVB frontend card connected to SoC TS input pins.
+
+Currently 7 TS input (tsin) channels are supported on the stih407 family SoC.
+
+Required properties (controller (parent) node):
+- compatible	: Should be "stih407-c8sectpfe"
+
+- reg		: Address and length of register sets for each device in
+		  "reg-names"
+
+- reg-names	: The names of the register addresses corresponding to the
+		  registers filled in "reg":
+			- c8sectpfe: c8sectpfe registers
+			- c8sectpfe-ram: c8sectpfe internal sram
+
+- clocks	: phandle list of c8sectpfe clocks
+- clock-names	: should be "c8sectpfe"
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+- pinctrl-names	: a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
+		   must be defined for each tsin child node.
+- pinctrl-0	: phandle referencing pin configuration for this tsin configuration
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+
+Required properties (tsin (child) node):
+
+- tsin-num	: tsin id of the InputBlock (must be between 0 to 6)
+- i2c-bus	: phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected.
+- rst-gpio	: reset gpio for this tsin channel.
+
+Optional properties (tsin (child) node):
+
+- invert-ts-clk		: Bool property to control sense of ts input clock (data stored on falling edge of clk).
+- serial-not-parallel	: Bool property to configure input bus width (serial on ts_data<7>).
+- async-not-sync	: Bool property to control if data is received in asynchronous mode
+			   (all bits/bytes with ts_valid or ts_packet asserted are valid).
+
+- dvb-card		: Describes the NIM card connected to this tsin channel.
+
+Example:
+
+/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
+
+	c8sectpfe@08a20000 {
+		compatible = "st,stih407-c8sectpfe";
+		status = "okay";
+		reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
+		reg-names = "stfe", "stfe-ram";
+		interrupts = <0 34 0>, <0 35 0>;
+		interrupt-names = "stfe-error-irq", "stfe-idle-irq";
+
+		pinctrl-names	= "tsin0-serial", "tsin0-parallel", "tsin3-serial",
+				"tsin4-serial", "tsin5-serial";
+
+		pinctrl-0	= <&pinctrl_tsin0_serial>;
+		pinctrl-1	= <&pinctrl_tsin0_parallel>;
+		pinctrl-2	= <&pinctrl_tsin3_serial>;
+		pinctrl-3	= <&pinctrl_tsin4_serial_alt3>;
+		pinctrl-4	= <&pinctrl_tsin5_serial_alt1>;
+
+		clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
+		clock-names = "stfe";
+
+		/* tsin0 is TSA on NIMA */
+		tsin0: port@0 {
+			tsin-num		= <0>;
+			serial-not-parallel;
+			i2c-bus			= <&ssc2>;
+			rst-gpio		= <&pio15 4 0>;
+			dvb-card		= <STV0367_TDA18212_NIMA_1>;
+		};
+
+		tsin3: port@3 {
+			tsin-num		= <3>;
+			serial-not-parallel;
+			i2c-bus			= <&ssc3>;
+			rst-gpio		= <&pio15 7 0>;
+			dvb-card		= <STV0367_TDA18212_NIMB_1>;
+		};
+	};