These changes are the raw update to linux-4.4.6-rt14. Kernel sources

are taken from kernel.org, and rt patch from the rt wiki download page.

During the rebasing, the following patch collided:

Force tick interrupt and get rid of softirq magic(I70131fb85).

Collisions have been removed because its logic was found on the
source already.

Change-Id: I7f57a4081d9deaa0d9ccfc41a6c8daccdee3b769
Signed-off-by: José Pekkarinen <jose.pekkarinen@nokia.com>

17 files changed, 977 insertions, 13 deletions

diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt
new file mode 100644
index 000000000..261df2799
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt
@@ -0,0 +1,15 @@
+88pm860x-backlight bindings
+
+Optional properties:
+  - marvell,88pm860x-iset: Current supplies on backlight device.
+  - marvell,88pm860x-pwm: PWM frequency on backlight device.
+
+Example:
+
+	backlights {
+		backlight-0 {
+			marvell,88pm860x-iset = <4>;
+			marvell,88pm860x-pwm = <3>;
+		};
+		backlight-2 {
+		};
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt
new file mode 100644
index 000000000..321be6640
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt
@@ -0,0 +1,16 @@
+gpio-backlight bindings
+
+Required properties:
+  - compatible: "gpio-backlight"
+  - gpios: describes the gpio that is used for enabling/disabling the backlight.
+    refer to bindings/gpio/gpio.txt for more details.
+
+Optional properties:
+  - default-on: enable the backlight at boot.
+
+Example:
+	backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/lp855x.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/lp855x.txt
new file mode 100644
index 000000000..0a3ecbc3a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/lp855x.txt
@@ -0,0 +1,70 @@
+lp855x bindings
+
+Required properties:
+  - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553",
+                "ti,lp8555", "ti,lp8556", "ti,lp8557"
+  - reg: I2C slave address (u8)
+  - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device.
+
+Optional properties:
+  - bl-name: Backlight device name (string)
+  - init-brt: Initial value of backlight brightness (u8)
+  - pwm-period: PWM period value. Set only PWM input mode used (u32)
+  - rom-addr: Register address of ROM area to be updated (u8)
+  - rom-val: Register value to be updated (u8)
+  - power-supply: Regulator which controls the 3V rail
+
+Example:
+
+	/* LP8555 */
+	backlight@2c {
+		compatible = "ti,lp8555";
+		reg = <0x2c>;
+
+		dev-ctrl = /bits/ 8 <0x00>;
+		pwm-period = <10000>;
+
+		/* 4V OV, 4 output LED0 string enabled */
+		rom_14h {
+			rom-addr = /bits/ 8 <0x14>;
+			rom-val = /bits/ 8 <0xcf>;
+		};
+
+		/* Heavy smoothing, 24ms ramp time step */
+		rom_15h {
+			rom-addr = /bits/ 8 <0x15>;
+			rom-val = /bits/ 8 <0xc7>;
+		};
+
+		/* 4 output LED1 string enabled */
+		rom_19h {
+			rom-addr = /bits/ 8 <0x19>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+	};
+
+	/* LP8556 */
+	backlight@2c {
+		compatible = "ti,lp8556";
+		reg = <0x2c>;
+
+		bl-name = "lcd-bl";
+		dev-ctrl = /bits/ 8 <0x85>;
+		init-brt = /bits/ 8 <0x10>;
+	};
+
+	/* LP8557 */
+	backlight@2c {
+		compatible = "ti,lp8557";
+		reg = <0x2c>;
+		power-supply = <&backlight_vdd>;
+
+		dev-ctrl = /bits/ 8 <0x41>;
+		init-brt = /bits/ 8 <0x0a>;
+
+		/* 4V OV, 4 output LED string enabled */
+		rom_14h {
+			rom-addr = /bits/ 8 <0x14>;
+			rom-val = /bits/ 8 <0xcf>;
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt
new file mode 100644
index 000000000..b4cffdaa4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt
@@ -0,0 +1,10 @@
+88pm860x-backlight bindings
+
+Optional properties:
+  - maxim,max8925-dual-string: whether support dual string
+
+Example:
+
+	backlights {
+		maxim,max8925-dual-string = <0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-pm8941-wled.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt
index a85a964d6..e5b294daf 100644
--- a/kernel/Documentation/devicetree/bindings/leds/leds-pm8941-wled.txt
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt
@@ -5,10 +5,9 @@ Required properties:
 - reg: slave address
 
 Optional properties:
-- label: The label for this led
-  See Documentation/devicetree/bindings/leds/common.txt
-- linux,default-trigger: Default trigger assigned to the LED
-  See Documentation/devicetree/bindings/leds/common.txt
+- default-brightness: brightness value on boot, value from: 0-4095
+	default: 2048
+- label: The name of the backlight device
 - qcom,cs-out: bool; enable current sink output
 - qcom,cabc: bool; enable content adaptive backlight control
 - qcom,ext-gen: bool; use externally generated modulator signal to dim
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
new file mode 100644
index 000000000..764db86d4
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
@@ -0,0 +1,35 @@
+pwm-backlight bindings
+
+Required properties:
+  - compatible: "pwm-backlight"
+  - pwms: OF device-tree PWM specification (see PWM binding[0])
+  - brightness-levels: Array of distinct brightness levels. Typically these
+      are in the range from 0 to 255, but any range starting at 0 will do.
+      The actual brightness level (PWM duty cycle) will be interpolated
+      from these values. 0 means a 0% duty cycle (darkest/off), while the
+      last value in the array represents a 100% duty cycle (brightest).
+  - default-brightness-level: the default brightness level (index into the
+      array defined by the "brightness-levels" property)
+  - power-supply: regulator for supply voltage
+
+Optional properties:
+  - pwm-names: a list of names for the PWM devices specified in the
+               "pwms" property (see PWM binding[0])
+  - enable-gpios: contains a single GPIO specifier for the GPIO which enables
+                  and disables the backlight (see GPIO binding[1])
+
+[0]: Documentation/devicetree/bindings/pwm/pwm.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+
+		power-supply = <&vdd_bl_reg>;
+		enable-gpios = <&gpio 58 0>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt
new file mode 100644
index 000000000..8bf2940f5
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt
@@ -0,0 +1,29 @@
+SKY81452-backlight bindings
+
+Required properties:
+- compatible		: Must be "skyworks,sky81452-backlight"
+
+Optional properties:
+- name			: Name of backlight device. Default is 'lcd-backlight'.
+- gpios			: GPIO to use to EN pin.
+			See Documentation/devicetree/bindings/gpio/gpio.txt
+- led-sources		: List of enabled channels from 0 to 5.
+			See Documentation/devicetree/bindings/leds/common.txt
+- skyworks,ignore-pwm	: Ignore both PWM input
+- skyworks,dpwm-mode	: Enable DPWM dimming mode, otherwise Analog dimming.
+- skyworks,phase-shift	: Enable phase shift mode
+- skyworks,short-detection-threshold-volt
+			: It should be one of 4, 5, 6 and 7V.
+- skyworks,current-limit-mA
+			: It should be 2300mA or 2750mA.
+
+Example:
+
+	backlight {
+		compatible = "skyworks,sky81452-backlight";
+		name = "pwm-backlight";
+		led-sources = <0 1 2 5>;
+		skyworks,ignore-pwm;
+		skyworks,phase-shift;
+		skyworks,current-limit-mA = <2300>;
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt b/kernel/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt
new file mode 100644
index 000000000..5fb9279ac
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt
@@ -0,0 +1,27 @@
+TPS65217 family of regulators
+
+The TPS65217 chip contains a boost converter and current sinks which can be
+used to drive LEDs for use as backlights.
+
+Required properties:
+- compatible: "ti,tps65217"
+- reg: I2C slave address
+- backlight: node for specifying WLED1 and WLED2 lines in TPS65217
+- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level)
+- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000
+- default-brightness: valid values: 0-100
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+	tps: tps@24 {
+		reg = <0x24>;
+		compatible = "ti,tps65217";
+		backlight {
+			isel = <1>;  /* 1 - ISET1, 2 ISET2 */
+			fdim = <100>; /* TPS65217_BL_FDIM_100HZ */
+			default-brightness = <50>;
+		};
+	};
+
diff --git a/kernel/Documentation/devicetree/bindings/leds/common.txt b/kernel/Documentation/devicetree/bindings/leds/common.txt
index 747c53805..68419843e 100644
--- a/kernel/Documentation/devicetree/bindings/leds/common.txt
+++ b/kernel/Documentation/devicetree/bindings/leds/common.txt
@@ -29,14 +29,23 @@ Optional properties for child nodes:
      "ide-disk" - LED indicates disk activity
      "timer" - LED flashes at a fixed, configurable rate
 
-- max-microamp : maximum intensity in microamperes of the LED
-		 (torch LED for flash devices)
-- flash-max-microamp : maximum intensity in microamperes of the
-                       flash LED; it is mandatory if the LED should
-		       support the flash mode
-- flash-timeout-us : timeout in microseconds after which the flash
-                     LED is turned off
+- led-max-microamp : Maximum LED supply current in microamperes. This property
+                     can be made mandatory for the board configurations
+                     introducing a risk of hardware damage in case an excessive
+                     current is set.
+                     For flash LED controllers with configurable current this
+                     property is mandatory for the LEDs in the non-flash modes
+                     (e.g. torch or indicator).
 
+Required properties for flash LED child nodes:
+- flash-max-microamp : Maximum flash LED supply current in microamperes.
+- flash-max-timeout-us : Maximum timeout in microseconds after which the flash
+                         LED is turned off.
+
+For controllers that have no configurable current the flash-max-microamp
+property can be omitted.
+For controllers that have no configurable timeout the flash-max-timeout-us
+property can be omitted.
 
 Examples:
 
@@ -49,7 +58,7 @@ system-status {
 camera-flash {
 	label = "Flash";
 	led-sources = <0>, <1>;
-	max-microamp = <50000>;
+	led-max-microamp = <50000>;
 	flash-max-microamp = <320000>;
-	flash-timeout-us = <500000>;
+	flash-max-timeout-us = <500000>;
 };
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/kernel/Documentation/devicetree/bindings/leds/leds-aat1290.txt
new file mode 100644
index 000000000..85c0c5861
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-aat1290.txt
@@ -0,0 +1,73 @@
+* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
+
+The device is controlled through two pins: FL_EN and EN_SET. The pins when,
+asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. CPU or camera sensor) there is an additional switch required, independent
+of the flash chip. The switch is controlled with pin control.
+
+Required properties:
+
+- compatible : Must be "skyworks,aat1290".
+- flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
+- enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
+
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+		"default" and "host" must refer to the same pin configuration
+		node, which sets the host as a strobe signal provider. Entry
+		"isp" must refer to the pin configuration node, which sets the
+		ISP as a strobe signal provider.
+
+A discrete LED element connected to the device must be represented by a child
+node - see Documentation/devicetree/bindings/leds/common.txt.
+
+Required properties of the LED child node:
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+                       Maximum flash LED supply current can be calculated using
+                       following formula: I = 1A * 162kohm / Rset.
+- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+                         Maximum flash timeout can be calculated using following
+                         formula: T = 8.82 * 10^9 * Ct.
+
+Optional properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+
+Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
+a switch that allows for routing strobe signal either from the host or from
+the camera sensor):
+
+#include "exynos4412.dtsi"
+
+aat1290 {
+	compatible = "skyworks,aat1290";
+	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
+	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default", "host", "isp";
+	pinctrl-0 = <&camera_flash_host>;
+	pinctrl-1 = <&camera_flash_host>;
+	pinctrl-2 = <&camera_flash_isp>;
+
+	camera_flash: flash-led {
+		label = "aat1290-flash";
+		led-max-microamp = <520833>;
+		flash-max-microamp = <1012500>;
+		flash-max-timeout-us = <1940000>;
+	};
+};
+
+&pinctrl_0 {
+	camera_flash_host: camera-flash-host {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <0>;
+	};
+
+	camera_flash_isp: camera-flash-isp {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <1>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6328.txt
new file mode 100644
index 000000000..3f48c1eaf
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6328.txt
@@ -0,0 +1,319 @@
+LEDs connected to Broadcom BCM6328 controller
+
+This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
+In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
+However, on some devices there are Serial LEDs (LEDs connected to a 74x164
+controller), which can either be controlled by software (exporting the 74x164
+as spi-gpio. See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
+by hardware using this driver.
+Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
+exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
+controlled, so the only chance to keep them working is by using this driver.
+
+BCM6328 LED controller has a HWDIS register, which controls whether a LED
+should be controlled by a hardware signal instead of the MODE register value,
+with 0 meaning hardware control enabled and 1 hardware control disabled. This
+is usually 1:1 for hardware to LED signals, but through the activity/link
+registers you have some limited control over rerouting the LEDs (as
+explained later in brcm,link-signal-sources). Even if a LED is hardware
+controlled you are still able to make it blink or light it up if it isn't,
+but you can't turn it off if the hardware decides to light it up. For this
+reason, hardware controlled LEDs aren't registered as LED class devices.
+
+Required properties:
+  - compatible : should be "brcm,bcm6328-leds".
+  - #address-cells : must be 1.
+  - #size-cells : must be 0.
+  - reg : BCM6328 LED controller address and size.
+
+Optional properties:
+  - brcm,serial-leds : Boolean, enables Serial LEDs.
+    Default : false
+  - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing.
+    Default : false
+  - brcm,serial-clk-low : Boolean, makes clock signal active low.
+    Default : false
+  - brcm,serial-dat-low : Boolean, makes data signal active low.
+    Default : false
+  - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction.
+    Default : false
+
+Each LED is represented as a sub-node of the brcm,bcm6328-leds device.
+
+LED sub-node required properties:
+  - reg : LED pin number (only LEDs 0 to 23 are valid).
+
+LED sub-node optional properties:
+  a) Optional properties for sub-nodes related to software controlled LEDs:
+    - label : see Documentation/devicetree/bindings/leds/common.txt
+    - active-low : Boolean, makes LED active low.
+      Default : false
+    - default-state : see
+      Documentation/devicetree/bindings/leds/leds-gpio.txt
+    - linux,default-trigger : see
+      Documentation/devicetree/bindings/leds/common.txt
+
+  b) Optional properties for sub-nodes related to hardware controlled LEDs:
+    - brcm,hardware-controlled : Boolean, makes this LED hardware controlled.
+      Default : false
+    - brcm,link-signal-sources : An array of hardware link
+      signal sources. Up to four link hardware signals can get muxed into
+      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
+      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
+      4 to 7. A signal can be muxed to more than one LED, and one LED can
+      have more than one source signal.
+    - brcm,activity-signal-sources : An array of hardware activity
+      signal sources. Up to four activity hardware signals can get muxed into
+      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
+      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
+      4 to 7. A signal can be muxed to more than one LED, and one LED can
+      have more than one source signal.
+
+Examples:
+Scenario 1 : BCM6328 with 4 EPHY LEDs
+	leds0: led-controller@10000800 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10000800 0x24>;
+
+		alarm_red@2 {
+			reg = <2>;
+			active-low;
+			label = "red:alarm";
+		};
+		inet_green@3 {
+			reg = <3>;
+			active-low;
+			label = "green:inet";
+		};
+		power_green@4 {
+			reg = <4>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+		ephy0_spd@17 {
+			reg = <17>;
+			brcm,hardware-controlled;
+		};
+		ephy1_spd@18 {
+			reg = <18>;
+			brcm,hardware-controlled;
+		};
+		ephy2_spd@19 {
+			reg = <19>;
+			brcm,hardware-controlled;
+		};
+		ephy3_spd@20 {
+			reg = <20>;
+			brcm,hardware-controlled;
+		};
+	};
+
+Scenario 2 : BCM63268 with Serial/GPHY0 LEDs
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+		brcm,serial-leds;
+		brcm,serial-dat-low;
+		brcm,serial-shift-inv;
+
+		gphy0_spd0@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0>;
+		};
+		gphy0_spd1@1 {
+			reg = <1>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <1>;
+		};
+		inet_red@2 {
+			reg = <2>;
+			active-low;
+			label = "red:inet";
+		};
+		dsl_green@3 {
+			reg = <3>;
+			active-low;
+			label = "green:dsl";
+		};
+		usb_green@4 {
+			reg = <4>;
+			active-low;
+			label = "green:usb";
+		};
+		wps_green@7 {
+			reg = <7>;
+			active-low;
+			label = "green:wps";
+		};
+		inet_green@8 {
+			reg = <8>;
+			active-low;
+			label = "green:inet";
+		};
+		ephy0_act@9 {
+			reg = <9>;
+			brcm,hardware-controlled;
+		};
+		ephy1_act@10 {
+			reg = <10>;
+			brcm,hardware-controlled;
+		};
+		ephy2_act@11 {
+			reg = <11>;
+			brcm,hardware-controlled;
+		};
+		gphy0_act@12 {
+			reg = <12>;
+			brcm,hardware-controlled;
+		};
+		ephy0_spd@13 {
+			reg = <13>;
+			brcm,hardware-controlled;
+		};
+		ephy1_spd@14 {
+			reg = <14>;
+			brcm,hardware-controlled;
+		};
+		ephy2_spd@15 {
+			reg = <15>;
+			brcm,hardware-controlled;
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
+
+Scenario 3 : BCM6362 with 1 LED for each EPHY
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+
+		usb@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0>;
+			brcm,activity-signal-sources = <0>;
+			/* USB link/activity routed to USB LED */
+		};
+		inet@1 {
+			reg = <1>;
+			brcm,hardware-controlled;
+			brcm,activity-signal-sources = <1>;
+			/* INET activity routed to INET LED */
+		};
+		ephy0@4 {
+			reg = <4>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <4>;
+			/* EPHY0 link routed to EPHY0 LED */
+		};
+		ephy1@5 {
+			reg = <5>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <5>;
+			/* EPHY1 link routed to EPHY1 LED */
+		};
+		ephy2@6 {
+			reg = <6>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <6>;
+			/* EPHY2 link routed to EPHY2 LED */
+		};
+		ephy3@7 {
+			reg = <7>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <7>;
+			/* EPHY3 link routed to EPHY3 LED */
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
+
+Scenario 4 : BCM6362 with 1 LED for all EPHYs
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+
+		usb@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0 1>;
+			brcm,activity-signal-sources = <0 1>;
+			/* USB/INET link/activity routed to USB LED */
+		};
+		ephy@4 {
+			reg = <4>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <4 5 6 7>;
+			/* EPHY0/1/2/3 link routed to EPHY0 LED */
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
+
+Scenario 5 : BCM6362 with EPHY LEDs swapped
+	leds0: led-controller@10001900 {
+		compatible = "brcm,bcm6328-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10001900 0x24>;
+
+		usb@0 {
+			reg = <0>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <0>;
+			brcm,activity-signal-sources = <0 1>;
+			/* USB link/act and INET act routed to USB LED */
+		};
+		ephy0@4 {
+			reg = <4>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <7>;
+			/* EPHY3 link routed to EPHY0 LED */
+		};
+		ephy1@5 {
+			reg = <5>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <6>;
+			/* EPHY2 link routed to EPHY1 LED */
+		};
+		ephy2@6 {
+			reg = <6>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <5>;
+			/* EPHY1 link routed to EPHY2 LED */
+		};
+		ephy3@7 {
+			reg = <7>;
+			brcm,hardware-controlled;
+			brcm,link-signal-sources = <4>;
+			/* EPHY0 link routed to EPHY3 LED */
+		};
+		power_green@20 {
+			reg = <20>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-bcm6358.txt b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6358.txt
new file mode 100644
index 000000000..b22a55bcc
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-bcm6358.txt
@@ -0,0 +1,145 @@
+LEDs connected to Broadcom BCM6358 controller
+
+This controller is present on BCM6358 and BCM6368.
+In these SoCs there are Serial LEDs (LEDs connected to a 74x164 controller),
+which can either be controlled by software (exporting the 74x164 as spi-gpio.
+See Documentation/devicetree/bindings/gpio/gpio-74x164.txt), or
+by hardware using this driver.
+
+Required properties:
+  - compatible : should be "brcm,bcm6358-leds".
+  - #address-cells : must be 1.
+  - #size-cells : must be 0.
+  - reg : BCM6358 LED controller address and size.
+
+Optional properties:
+  - brcm,clk-div : SCK signal divider. Possible values are 1, 2, 4 and 8.
+    Default : 1
+  - brcm,clk-dat-low : Boolean, makes clock and data signals active low.
+    Default : false
+
+Each LED is represented as a sub-node of the brcm,bcm6358-leds device.
+
+LED sub-node required properties:
+  - reg : LED pin number (only LEDs 0 to 31 are valid).
+
+LED sub-node optional properties:
+  - label : see Documentation/devicetree/bindings/leds/common.txt
+  - active-low : Boolean, makes LED active low.
+    Default : false
+  - default-state : see
+    Documentation/devicetree/bindings/leds/leds-gpio.txt
+  - linux,default-trigger : see
+    Documentation/devicetree/bindings/leds/common.txt
+
+Examples:
+Scenario 1 : BCM6358
+	leds0: led-controller@fffe00d0 {
+		compatible = "brcm,bcm6358-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xfffe00d0 0x8>;
+
+		alarm_white {
+			reg = <0>;
+			active-low;
+			label = "white:alarm";
+		};
+		tv_white {
+			reg = <2>;
+			active-low;
+			label = "white:tv";
+		};
+		tel_white {
+			reg = <3>;
+			active-low;
+			label = "white:tel";
+		};
+		adsl_white {
+			reg = <4>;
+			active-low;
+			label = "white:adsl";
+		};
+	};
+
+Scenario 2 : BCM6368
+	leds0: led-controller@100000d0 {
+		compatible = "brcm,bcm6358-leds";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x100000d0 0x8>;
+		brcm,pol-low;
+		brcm,clk-div = <4>;
+
+		power_red {
+			reg = <0>;
+			active-low;
+			label = "red:power";
+		};
+		power_green {
+			reg = <1>;
+			active-low;
+			label = "green:power";
+			default-state = "on";
+		};
+		power_blue {
+			reg = <2>;
+			label = "blue:power";
+		};
+		broadband_red {
+			reg = <3>;
+			active-low;
+			label = "red:broadband";
+		};
+		broadband_green {
+			reg = <4>;
+			label = "green:broadband";
+		};
+		broadband_blue {
+			reg = <5>;
+			active-low;
+			label = "blue:broadband";
+		};
+		wireless_red {
+			reg = <6>;
+			active-low;
+			label = "red:wireless";
+		};
+		wireless_green {
+			reg = <7>;
+			active-low;
+			label = "green:wireless";
+		};
+		wireless_blue {
+			reg = <8>;
+			label = "blue:wireless";
+		};
+		phone_red {
+			reg = <9>;
+			active-low;
+			label = "red:phone";
+		};
+		phone_green {
+			reg = <10>;
+			active-low;
+			label = "green:phone";
+		};
+		phone_blue {
+			reg = <11>;
+			label = "blue:phone";
+		};
+		upgrading_red {
+			reg = <12>;
+			active-low;
+			label = "red:upgrading";
+		};
+		upgrading_green {
+			reg = <13>;
+			active-low;
+			label = "green:upgrading";
+		};
+		upgrading_blue {
+			reg = <14>;
+			label = "blue:upgrading";
+		};
+	};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-ktd2692.txt b/kernel/Documentation/devicetree/bindings/leds/leds-ktd2692.txt
new file mode 100644
index 000000000..853737452
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-ktd2692.txt
@@ -0,0 +1,50 @@
+* Kinetic Technologies - KTD2692 Flash LED Driver
+
+KTD2692 is the ideal power solution for high-power flash LEDs.
+It uses ExpressWire single-wire programming for maximum flexibility.
+
+The ExpressWire interface through CTRL pin can control LED on/off and
+enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current,
+Flash timeout, LVP(low voltage protection).
+
+Also, When the AUX pin is pulled high while CTRL pin is high,
+LED current will be ramped up to the flash-mode current level.
+
+Required properties:
+- compatible : Should be "kinetic,ktd2692".
+- ctrl-gpios : Specifier of the GPIO connected to CTRL pin.
+- aux-gpios : Specifier of the GPIO connected to AUX pin.
+
+Optional properties:
+- vin-supply : "vin" LED supply (2.7V to 5.5V).
+  See Documentation/devicetree/bindings/regulator/regulator.txt
+
+A discrete LED element connected to the device must be represented by a child
+node - See Documentation/devicetree/bindings/leds/common.txt
+
+Required properties for flash LED child nodes:
+  See Documentation/devicetree/bindings/leds/common.txt
+- led-max-microamp : Minimum Threshold for Timer protection
+  is defined internally (Maximum 300mA).
+- flash-max-microamp : Flash LED maximum current
+  Formula : I(mA) = 15000 / Rset.
+- flash-max-timeout-us : Flash LED maximum timeout.
+
+Optional properties for flash LED child nodes:
+- label : See Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+ktd2692 {
+	compatible = "kinetic,ktd2692";
+	ctrl-gpios = <&gpc0 1 0>;
+	aux-gpios = <&gpc0 2 0>;
+	vin-supply = <&vbat>;
+
+	flash-led {
+		label = "ktd2692-flash";
+		led-max-microamp = <300000>;
+		flash-max-microamp = <1500000>;
+		flash-max-timeout-us = <1835000>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-netxbig.txt b/kernel/Documentation/devicetree/bindings/leds/leds-netxbig.txt
new file mode 100644
index 000000000..5ef92a26d
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-netxbig.txt
@@ -0,0 +1,92 @@
+Binding for the CPLD LEDs (GPIO extension bus) found on some LaCie/Seagate
+boards (Example: 2Big/5Big Network v2, 2Big NAS).
+
+Required properties:
+- compatible: "lacie,netxbig-leds".
+- gpio-ext: Phandle for the gpio-ext bus.
+
+Optional properties:
+- timers: Timer array. Each timer entry is represented by three integers:
+  Mode (gpio-ext bus), delay_on and delay_off.
+
+Each LED is represented as a sub-node of the netxbig-leds device.
+
+Required sub-node properties:
+- mode-addr: Mode register address on gpio-ext bus.
+- mode-val: Mode to value mapping. Each entry is represented by two integers:
+  A mode and the corresponding value on the gpio-ext bus.
+- bright-addr: Brightness register address on gpio-ext bus.
+- max-brightness: Maximum brightness value.
+
+Optional sub-node properties:
+- label: Name for this LED. If omitted, the label is taken from the node name.
+- linux,default-trigger: Trigger assigned to the LED.
+
+Example:
+
+netxbig-leds {
+	compatible = "lacie,netxbig-leds";
+
+	gpio-ext = &gpio_ext;
+
+	timers = <NETXBIG_LED_TIMER1 500 500
+		  NETXBIG_LED_TIMER2 500 1000>;
+
+	blue-power {
+		label = "netxbig:blue:power";
+		mode-addr = <0>;
+		mode-val = <NETXBIG_LED_OFF 0
+			    NETXBIG_LED_ON 1
+			    NETXBIG_LED_TIMER1 3
+			    NETXBIG_LED_TIMER2 7>;
+		bright-addr = <1>;
+		max-brightness = <7>;
+	};
+	red-power {
+		label = "netxbig:red:power";
+		mode-addr = <0>;
+		mode-val = <NETXBIG_LED_OFF 0
+			    NETXBIG_LED_ON 2
+			    NETXBIG_LED_TIMER1 4>;
+		bright-addr = <1>;
+		max-brightness = <7>;
+	};
+	blue-sata0 {
+		label = "netxbig:blue:sata0";
+		mode-addr = <3>;
+		mode-val = <NETXBIG_LED_OFF 0
+			    NETXBIG_LED_ON 7
+			    NETXBIG_LED_SATA 1
+			    NETXBIG_LED_TIMER1 3>;
+		bright-addr = <2>;
+		max-brightness = <7>;
+	};
+	red-sata0 {
+		label = "netxbig:red:sata0";
+		mode-addr = <3>;
+		mode-val = <NETXBIG_LED_OFF 0
+			    NETXBIG_LED_ON 2
+			    NETXBIG_LED_TIMER1 4>;
+		bright-addr = <2>;
+		max-brightness = <7>;
+	};
+	blue-sata1 {
+		label = "netxbig:blue:sata1";
+		mode-addr = <4>;
+		mode-val = <NETXBIG_LED_OFF 0
+			    NETXBIG_LED_ON 7
+			    NETXBIG_LED_SATA 1
+			    NETXBIG_LED_TIMER1 3>;
+		bright-addr = <2>;
+		max-brightness = <7>;
+	};
+	red-sata1 {
+		label = "netxbig:red:sata1";
+		mode-addr = <4>;
+		mode-val = <NETXBIG_LED_OFF 0
+			    NETXBIG_LED_ON 2
+			    NETXBIG_LED_TIMER1 4>;
+		bright-addr = <2>;
+		max-brightness = <7>;
+	};
+};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt b/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt
index aef3aca34..9f81258a5 100644
--- a/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-ns2.txt
@@ -8,6 +8,9 @@ Each LED is represented as a sub-node of the ns2-leds device.
 Required sub-node properties:
 - cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification.
 - slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification.
+- modes-map: A mapping between LED modes (off, on or SATA activity blinking) and
+  the corresponding cmd-gpio/slow-gpio values. All the GPIO values combinations
+  should be given in order to avoid having an unknown mode at driver probe time.
 
 Optional sub-node properties:
 - label: Name for this LED. If omitted, the label is taken from the node name.
@@ -15,6 +18,8 @@ Optional sub-node properties:
 
 Example:
 
+#include <dt-bindings/leds/leds-ns2.h>
+
 ns2-leds {
 	compatible = "lacie,ns2-leds";
 
@@ -22,5 +27,9 @@ ns2-leds {
 		label = "ns2:blue:sata";
 		slow-gpio = <&gpio0 29 0>;
 		cmd-gpio = <&gpio0 30 0>;
+		modes-map = <NS_V2_LED_OFF  0 1
+			     NS_V2_LED_ON   1 0
+			     NS_V2_LED_ON   0 0
+			     NS_V2_LED_SATA 1 1>;
 	};
 };
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-powernv.txt b/kernel/Documentation/devicetree/bindings/leds/leds-powernv.txt
new file mode 100644
index 000000000..66655690f
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-powernv.txt
@@ -0,0 +1,26 @@
+Device Tree binding for LEDs on IBM Power Systems
+-------------------------------------------------
+
+Required properties:
+- compatible : Should be "ibm,opal-v3-led".
+- led-mode   : Should be "lightpath" or "guidinglight".
+
+Each location code of FRU/Enclosure must be expressed in the
+form of a sub-node.
+
+Required properties for the sub nodes:
+- led-types : Supported LED types (attention/identify/fault) provided
+              in the form of string array.
+
+Example:
+
+leds {
+	compatible = "ibm,opal-v3-led";
+	led-mode = "lightpath";
+
+	U78C9.001.RST0027-P1-C1 {
+		led-types = "identify", "fault";
+	};
+	...
+	...
+};
diff --git a/kernel/Documentation/devicetree/bindings/leds/leds-tlc591xx.txt b/kernel/Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
new file mode 100644
index 000000000..3bbbf7024
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
@@ -0,0 +1,40 @@
+LEDs connected to tlc59116 or tlc59108
+
+Required properties
+- compatible: should be "ti,tlc59116" or "ti,tlc59108"
+- #address-cells: must be 1
+- #size-cells: must be 0
+- reg: typically 0x68
+
+Each led is represented as a sub-node of the ti,tlc59116.
+See Documentation/devicetree/bindings/leds/common.txt
+
+LED sub-node properties:
+- reg: number of LED line, 0 to 15 or 0 to 7
+- label: (optional) name of LED
+- linux,default-trigger : (optional)
+
+Examples:
+
+tlc59116@68 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "ti,tlc59116";
+	reg = <0x68>;
+
+	wan@0 {
+		label = "wrt1900ac:amber:wan";
+		reg = <0x0>;
+	};
+
+	2g@2 {
+		label = "wrt1900ac:white:2g";
+		reg = <0x2>;
+	};
+
+	alive@9 {
+		label = "wrt1900ac:green:alive";
+		reg = <0x9>;
+		linux,default_trigger = "heartbeat";
+	};
+};